Ilumipod Inground Tri-3 IP Optic WW User Manual Rev. 5
Contents
1. Turns the unit on The unt will tun off y oa urns the unit on The unit will turn o lt POWER gt automatically after 30 seconds of inactivity DOWN Control Options You can set the Ilumipod Inground Tri 3 IP Optic 25 WW start address in the 001 512 DMX range This allows for the control of up to 512 products in the 1 channel SOLID personality Programming Carry out all the programming procedures indicated below from the control panel Refer to the Menu Map section to learn how the menu options relate to each other Use ENTER and MENU to change levels in the Menu Map moving right and left respectively Use UP and DOWN to move vertically within the Menu Map DMX Personality When you scroll 1 Goto PERSON and select SOLID personality e Mm 2 Make sure to rearrange the DMX addresses of all products in the current DMX you sos universe to avoid address overlapping many of them that do not correspond with the menu DMX Starting Address map Skip them as they do not work with the l Goto DMX WW only output 2 Select a starting DMX address 001 512 products llumipod Inground Tri 3 IP Optic 25 WW User Manual Rev 5 11 Operation ILUMINAR Static Colors 1 Goto STATIC 2 Select a color COOL 3 Select a color value 000 255 0 100 Dimmer This setting gives the user four different options to simulate the dimming curve of an incandescent lighting product DIM1 is the 1 Goto DIMMER d2. 2 Select a dimming curve OFF or DIMI 4 is the slowest Procedure DIMMER Description OFF Dimmer curve is linear with fader DIMI Non linear fastest DIM2 Non linear fast DIM3 Non linear slow DIM4 Non linear slowest Reset to Factory Settings 1 Goto SETTINGS gt RESET 2 Select YES or NO Menu Map Main Level Programming Levels Description DMX Sets the DMX starting address PERSON a DIMMER OFF Dimmer works in linear mode Dimmer works in non linear mode from fast to slow STATIC Configures the static color SETTINGS RESET YES Resets unit to factory default settings NO DMX Values SOLID Channel Function Value Percent Setting 1 Dimmer 000 255 0 100 12 llumipod Inground Tri 3 IP Optic 25 WW User Manual Rev 5 IL UIMIITI m r3 i m i a m JARC Technical Information 5 Technical Information Product Maintenance To maintain optimum performance and minimize wear clean the products frequently Usage and environment are contributing factors in determining the cleaning frequency As a general guideline products should be cleaned at least twice a month Dust build up reduces light output performance and can cause overheating This can lead to reduced light source life For products containing external optical lenses clean them periodically to optimize light output The cleaning frequency depends on the environment in which the product operates Always dry the Damp smoky or particularly dirty sur
3. Ilumicode Addresser IP67 ingress protection GORE valve Drive over rated glass lens cover High power 2 3 W 700 mA tri emitter LEDs Additional Equipment Ilumicode addresser required for product configuration sold separately llumipod Inground Tri 3 IP Optic 25 WW User Manual Rev 5 3 Product Description LUMINARC Overview Installation Sleeve 316 Stainless Steel Gland Nuts Tri emitter LEDs 4 llumipod Inground Tri 3 IP Optic 25 WW User Manual Rev 5 LUMINARC Product Description Dimensions 6 0 in 153 mm llumipod Inground Tri 3 IP Optic 25 WW User Manual Rev 5 3 Installation Installation Notes The Ilumipod Inground Tri 3 IP Optic 25 WW consists of two parts the product housing and the concrete installation sleeve The product housing is IP67 rated The installation sleeve is not Read the Installation Sleeve Setup instructions carefully Always keep the Do not use the product s junction box to extend the power or signal cables to other units This D ecd might compromise the IP rating of the junction box Instead use individual cables from the cables by running product to the corresponding distribution boxes them in different conduits and using separate Installation Sleeve Orientation distribution boxes E l You will have to run the AC power and signal cables from the base of the fixture into the installation sleeve Position the installation sleeve so that the signa
4. World Wide Web www chauvet com mx Technical Support Email Eutech chauvetlighting eu World Wide Web www chauvetlighting eu llumipod Inground Tri 3 IP Optic 25 WW User Manual Rev 5 17 Technical Information IL LJIVIIINZAFSL Technical Specifications Dimensions and Weight Length Width Height Weight 6 0 in 153 mm 6 0 in 153 mm 7 0 in 178 mm 4 6 Ib 2 0 kg Note Dimensions in inches rounded to the nearest decimal digit Electrical Power Supply Type Range Voltage Selection Switching internal 100 to 240 VAC 50 60 Hz Auto ranging Parameter 120 V 60 Hz 230 V 50 Hz Consumption 11 W Operating current 0 1A Power I O Mmnpt O Output Connectors N A Cord plug N A N A Light Source Type Power Lifespan LED 2 3 W 50 000 hours Color Quantit Current Warm White 3100 K 3 700 mA Photometric Parameter Standard 252 Optics Illuminance O 5 m Beam angle I Field angle 297 Thermal Max External Temperature Cooling System 113 F 45 C Convection DMX I O Connectors Channel Range Open Wire Open Wire 1 Ordering Product Name UPC Number hie o t 01630585 781462209339 RoHS UL 1573 B CSAC22 2 No 166 E C US E113093 gt 18 llumipod Inground Tri 3 IP Optic 25 WW User Manual Rev 5 ILUMINARC LUMINARC
5. Ilumipod Inground Tri 3 IP Optic 25 WW User Manual Edition Notes Edition Notes i i j ip ni I J n gm mm LJ IVI N A H b 8 y E mus The Ilumipod Inground Tri 3 IP Optic 25 WW User Manual Rev 5 covers the description safety precautions installation programming operation and maintenance of the Ilumipod Inground Tri 3 IP Optic 25 WW ILUMINARC released this edition of the Ilumipod Inground Tri 3 IP Optic 25 WW User Manual Rev 5 in May 2015 Trademarks The ILUMINARC logo the ILUMINARC Q name and all other trademarks in this document related to services or products by ILUMINARC are trademarks owned or licensed by ILUMINARC its affiliates or subsidiaries Any other product names logos brands company names trademarks featured or referred to within this document are the property of their respective trademark holders Copyright Notice The entire content of this document except where applicable and unless otherwise noted is solely owned by ILUMINARC a wholly owned trademark of Chauvet amp Sons Inc Copyright 2015 ILUMINARC All rights reserved Electronically published by ILUMINARC in the United States of America Manual Usage ILUMINARC authorizes its customers to download and print this manual for professional information purposes only ILUMINARC expressly prohibits the usage copy storage distribution modification or printing of this manual or its content for any othe
6. Information Polar Candela Distribution 2 900 e 41 170 160 1502 140 130 1 933 Max Candela 2 885 7 at Horizontal 0 Vertical 1 1 450 120 Input Wattage 9 8 367 110 Luminous Opening Point 1008 Test 20120523 am Test Date 2012 05 23 Test Lab ILUMI NARC R amp D E Photometry Type B zu CIE Class Direct Ege 50 10 20 30 40 B 0H E 30 H Flood Summary Efficiency Lumens Horizontal Spread Vertical Spread Field 1096 52 796 210 6 29 1 29 Beam 50 23 7 94 9 15 2 14 5 Total 62 5 250 0 Illuminance at a Distance Center Beam Fc 0 6 ft 1 5 ft 273 6 fc 69 6 fc 2 3 t 3 1 FE 3 8 ft 4 6 FE 31 0 fc 17 4 fc 11 1 fc 7 1 c Spread 14 5 MhHoriz Spread 15 2 Beam Width 0 8 ft 1 6 Ft 2 4 ft 3 2 FE 4 0 Ft 4 8 Ft Photometrics Pro 1 3 21 copyright 2003 2012 by jSolutions Inc Reported data calculated from manufacturer s data file based on IES recommended methods llumipod Inground Tri 3 IP Optic 25 WW User Manual Rev 5 15 Technical Information ILUMINAR LED Disclaimer LED Life ILUMINARCO rates LED lifetime based on lumen depreciation of 70 of the original output with data provided by the manufacturer of the LED Data from the manufacturer of the LED are not independently verified or measured by ILUMINARCO When the product is operating in optimal environmental conditions the LED lifetime is rated to be 50 000 to 70 000 hours by the LED manufacturer
7. LED Binning LED manufacturers sort LEDs into bins based on variances in color output intensity and the frequency at which the semiconductor operates ILUMINARC strives to hold its LED manufacturers to the highest standards of binning to optimize consistency in output from product to product However the availability of a single bin cannot be guaranteed With that in mind ILUMINARC has developed a rigorous control system to seek the best achievable consistency in color and output Color Rendering Index CRI CRI is an industry standard method to compare properties of different types of light sources There are known limitations and inconsistencies related to CRI Results may vary depending on the environmental factors involved For this reason the U S Department of Energy DOE states that CRI should be considered as one point of reference among others in evaluating white LED products and systems The following is an excerpt of recommendations from the DOE 1 Identify the visual tasks to be performed under the light source If color fidelity under different light sources is critically important for example in a space where color or fabric comparisons are made under both daylight and electric lighting CRI values may be a useful metric for rating LED products 2 CRI may be compared only for light sources of equal correlated color temperature This applies to all light sources not only to LEDs Also differences in CRI values
8. ONTO ODIA S tartrate rr D D ante re Tm 11 Progra MTN ara di 11 DMX Personally nO E cS 11 DMX Starting Address in t T m e T 11 UN Ol Ol EET EDEN 12 Bla arse hts E Cn A PETERE PESCE 12 Reser IO FACIONy SUING me ae cl gal ai a i it ali a ald gate haat 12 A A dictates 12 IN oN ISS ite iid at persica ea e TR 12 SR A 12 llumipod Inground Tri 3 IP Optic 25 WW User Manual Rev 5 i Table of Contents ILUMINARC 5 Technical Information n 13 Produce Manten CO sisas idos 13 PIOGHCETIODAIES aida ia di A 13 TroUDIESNOOUNO Guidez er E 14 PROMET Soaic a a ds 15 LEDS cialmente 16 LED EIO pana Utada 16 LED BINNING sasse RR IN 16 Color Rendering index GA io iio aires 16 A ad seater Ga ta etc S E dens geet aoa uate aun Sean ed M ant 17 Contact US ossis instan aM edad 17 TECHNICAL PEC Ier dile RIEN di 18 llumipod Inground Tri 3 IP Optic 25 WW User Manual Rev 5 E M UMINARC ILU INAR Introduction 1 Introduction Critical What Is In the Box installation configuration or operation information Ilumipod Inground Tri 3 IP Optic 25 WW Failure to comply with this Installation Sleeve information may render the product partially or Warranty Card completely inoperative damage third party Quick Reference Guide equipment or cause harm to the user Unpacking Instructions Immediately upon receiving a product from ILUMINARC carefully unpack the carton D pL ai Che
9. Optic 25 WW User Manual Rev 5 pif Table of Contents Table of Contents A irere TI 1 WAS ITE BO RANA UU 1 UNICO IAS UON MN NE o oe eer ene ere ol aed 1 A cages hess cerca MM MI MM E E eo E EE MM M d LIU ae se 1 TEX CONV RR PE m m es 1 Salei NOG S ec antes atender it cosa ovo ft eut ce sedebit vota ie rc dot ou testas uS ob cota ad Lc d eui eed a D cd cU D re 2 lA AA A eE GE eed aceat ase a ELE O UL La 2 MOUMUNG Ez gie ASTANA OM ERES pm 2 meli GIG VINO eet ET MEE M 2 Operadlo em ee ee 2 2 Product DESCIIDUOM mre a 3 ESAS de e ase 3 e acces ciadasussteoiu se Sasastataiaceasoancescetssnce e a e a dal sinks state eo iuded astantes 3 Gad c c mm PES 4 DIMENSIONS e e EE 5 A f e t RS 6 Ils tallatlore INDIOS eise banda htnc o comu ca ecu Me Lou eire 6 Installation oleeveOre n allOT cas 6 Installation Sleeve Selup emen a sod Aue ed A I a Li a al 6 AC IR OW M B 7 mie r iere PIN eo RN ETT 7 nian C Y mio iim WIM nosse e P DS 7 DMX HNKIN G Lips iii ads 8 A A A a 8 SIC VV sur tlis 8 Protocol CONNSCUIVI TEE ES EP 8 degit LS Seta acest cee cya A TUE 9 AI mn ao ta ema ona arte era OTA on eS SO a Se OTe eo 9 l micade Addresser ic siii ls 10 4 Opera idad 11 llummicode Addresser ia 11 lu micode Panel Describir E 11 C
10. X products compatible with the Ilumipod Inground Tri 3 IP Optic 25 WW you can control each individually with a single DMX controller If you are not familiar with the DMX standard or if you need information about the DMX cables needed to link the Ilumipod Inground Tri 3 IP Optic 25 WW to a DMX controller you may download the DMX Primer from the ILUMINARC website at http www iluminarc com reports dmx primer DMX Modes The Ilumipod Inground Tri 3 IP Optic 25 WW uses the standard DMX data connection for its SOLID personality Refer to the Introduction chapter for a brief description of this mode Refer to the Operation chapter to learn how to configure the Ilumipod Inground Tri 3 IP Optic 25 WW to work in this mode The DMX Values section provides detailed information regarding the DMX mode DMX Mode SOLID DMX Address 512 Signal Wiring To provide signal for the Ilumipod Inground Tri 3 IP Optic 25 WW you can connect the bare ended IP67 rated signal cable from the product to two IP67 rated signal connectors DMX In DMX Out or use an IP67 rated junction box In this case make sure to use IP67 rated conduit Protocol Connectivity The Ilumipod Inground Tri 3 IP Optic 25 WW uses the USITT DMX 512 Protocol The procedure below illustrates the recommended connection method 1 Common Shield im 2 Data In Black 3 Data In White 4 Data Out Green 5 Data Out Red Junction box Jun
11. ck the contents of the box to ensure that all parts are present and that they are in good configuration condition information Failure to comply with this Claims information may prevent I l Wm the product from The carrier is responsible for any damage incurred during shipping Therefore if the received functioning correctly merchandise appears to have been damaged during shipping the customer must submit the damage report and any related claims to the carrier not ILUMINARCO The customer must Useful submit the report upon receipt of the damaged merchandise Failure to do so in a timely information manner may invalidate the customer s claim with the carrier For other issues such as missing components or parts damage not related to shipping or concealed damage the customer must make claims to ILUMINARC within 7 days of receiving the merchandise Text Conventions Convention Meaning 1 512 A range of values in the text 50 60 A set of mutually exclusive values in the text DMX Primer The name of another publication or manual The term DMX lt SET gt A button on the product s control panel used throughout this document Settings A product function or a menu option refers to the USITT MENU gt Settings A sequence of menu options DMX512 A transmission protocol 1 10 A range of menu values from which to choose in a menu Yes No A set of two mutually exclusive menu options in a menu ON A unique value to enter or selec
12. ction Conduit box llumipod Inground Tri 3 IP Optic 25 WW User Manual Rev 5 Controllers If you have not Th l D configured the e Ilumipod Inground Tri 3 IP Optic 25 WW can operate with a standard DMX controller or DMX starting the ILUMICODE addresser The sections below provide information on how to connect these address and products to the corresponding controllers The instructions to operate these products with each DMX mode for each of the above controllers are in the Operation chapter of this manual product they will all use their default values This means that all products DMX Controller will operate in unison The Ilumipod Inground Tri 3 IP Optic 25 WW can work with a standard DMX controller The channel assignments will depend on the chosen personality see the corresponding Menu Map section and the DMX address assigned to each product see the Programming section The figure below illustrates how to connect the DMX controller to the Ilumipod Inground Tri 3 IP Optic 25 WW To aieo other Earann fixtures DMX512 A Controller All llumipod Inground Tri 3 IP Optic 25 WW User Manual Rev 5 9 Installation LUMINARC llumicode Addresser To assign individual D DMX addressesto The Ilumipod Inground Tri 3 IP Optic 25 WW uses the Ilumicode addresser Ilumicode for each product you configuration purposes The diagram below shows how to connect the Ilumicode to this product must connect t
13. eaker fuse keeps eeu tripping blowing Short circuit along the power wires Check for a short in the electrical wiring Check for power on power outlet Product does not power up Loose or damaged power cord Check power cord Faulty internal power supply Return for service to ILUMINARC 9 Wrong DMX addressing Check Control Panel and product addressing Damaged DMX cables Check DMX cables Product does not respond to Wrong polarity on the controller og wens Loose DMX cables Check cable connections Faulty DMX interface Return for service to ILUMINARC 9 Faulty Display Main board Return for service to ILUMINARC Non DMX cables Use only DMX compatible cables Install terminator as suggested in the DMX Primer from the ILUMINARC website at http www iluminarc com reports dmx rimer O n3 e Bouncing signals DMX signal problems Install an optically coupled DMX splitter FORE Ca eno ENC eine right after the product with the strong signal Install an optically coupled DMX splitter Too many products after product 32 or before Keep DMX cables separated from power Interference from AC wires cables or fluorescent black lights MI Mumipod Inground Tri 3 IP Optic 25 WW User Manual Rev 5 ILUMINA RC Photometrics Filename Manufacturer Luminaire Lamp Output ILUMI POD I NGROUND TRI 3 IP OPTIC 25 WW ILUMINARC Ilumipod Inground Tri 3 IP Optic 25 WW 1 lamp rated lumens lamp 400 Technical
14. eceive the RMA please include the following information on a piece of paper inside the box Your name Your address Your phone number The RMA A brief description of the problem Be sure to pack the product properly Any shipping damage resulting from inadequate packaging will be the customer s responsibility FedEx packing or double boxing are recommended WORLD HEADQUARTERS ILUMINARC General Information Address 5200 NW 108th Avenue Sunrise FL 33351 Voice 954 923 3680 Fax 800 544 4898 World Wide Web www iluminarc com UNITED KINGDOM AND IRELAND Chauvet Europe Ltd General Information Technical Support Address Unit 1C Email uktech iluminarc com Brookhill Road Industrial Estate Pinxton Nottingham UK World Wide Web www chauvetlighting co uk NG16 6NT Voice 44 0 1773 511115 Fax 44 0 1773 511110 MEXICO Chauvet Mexico General Information Address Av Santa Ana 30 Parque Industrial Lerma Lerma Mexico C P 52000 Voice 52 728 285 5000 CHAUVET EUROPE Chauvet Europe BVBA General Information Address Stokstraat 18 9770 Kruishoutem Belgium Voice 32 9 388 93 97 Outside the U S United Kingdom Ireland Mexico or Benelux contact the dealer of record Follow their instructions to request support or to return a product Visit our website for contact details Technical Support Voice 800 762 1074 Email support iluminarc com Technical Support Email servicio iluminarc com mx
15. he lumicodaaddresserto each This connection will control multiple products at the same time all having the same DMX product individually address Important The Ilumicode must be used to configure this product The Ilumicode can be D o nd T purchased separately through your ILUMINARC sales representative connect no more than 20 products in this mode and keep the total distance to less than 60 m 197 ft Otherwise you might need to use an optically isolated signal amplifier OS OD xS RSS HK b Sexo 2 amp x To other fixtures r1 g 1 Gnd 1 Gnd Black clip 2 Data 2 Data Green clip 3 Data 3 Data Red clip DMX Output Signal Connector llumicode Addresser 10 llumipod Inground Tri 3 IP Optic 25 WW User Manual Rev 5 HU Operation 4 Operation llumicode Addresser The Ilumipod Inground Tri 3 IP Optic 25 WW needs an external controller the Ilumicode addresser IIumicode to change its configuration llumicode Panel Description Button Function lt MENU gt Exits from the current menu or function Enables the currently displayed menu or sets the lt ENTER gt currently selected value into the selected function Navigates upwards through the menu list and lt UP gt l l increases the numeric value when in a function O Navigates downwards through the menu list and UP lt DOWN gt 8 ae O decreases the numeric value when in a function
16. l cable exits the sleeve using one of the two cable outlets Use the opposite outlet for the power cable refer to the following figure This method will reduce the stress to the signal and power cables when setting the product down while keeping them separated under the product s housing Signal cable Power cable To power P distribution box Installation Sleeve Setup al n eann T A o signal distribution box When setting up the installation sleeve make sure that any water that may have entered can drain out of the sleeve Locate the installation sleeve above the normal drainage level so the product is never under more than m of water for more than 30 minutes IP67 during heavy rain In addition make sure that the installation sleeve and the stainless steel collar are horizontal and even with the ground surface This helps distribute the load uniformly over the product s surface and avoids creating dangerous bumps Collar llumipod Inground Tri 3 IP Optic 25 WW products can support a distributed load of up to 3 000 kg 6 614 Ib when properly installed Concrete Drainpipe Hardpan 6 llumipod Inground Tri 3 IP Optic 25 WW User Manual Rev 5 LUMINARC Always connect N the llumipod Inground Tri 3 IP Optic 25 WW to a protected circuit with an appropriate electrical ground to avoid the risk of electrocution o
17. lor U S Wire Europe IP67 Pin AC Ground Green Yellow Green Green Yellow 3 Power Wiring You can connect the bare ended IP67 rated AC power cable from the product to an IP67 rated power connector or IP67 rated junction box If using junction boxes make sure to use IP67 rated conduit for surface installations From To fuse other panel boxes J Green Jj LLL LL Conduit Distribution Box Distribution Box llumipod Inground Tri 3 IP Optic 25 WW User Manual Rev 5 7 Installation The llumipod Inground Tri 3 IP Optic 25 WW must be linked using DMX cable in a daisy chain serial fashion To comply with the ElA 485 standard no more than 32 products should be connected on one daisy chain without using a DMX optically isolated splitter Doing otherwise may result in deterioration of the digital DMX signal _ USITT A recommends limiting the total length of the DMX cable from the first product controller to the last product to 300 455 m 985 1 500 ft product from the AC power before opening it D must match or exceed the electrical characteristics of the Belden 9841 cable for EIA RS 485 applications You may also use CAT5 5e or CAT6 LAN cable Disconnect the The signal cable ILUMINARC DMX Linking You may link the Ilumipod Inground Tri 3 IP Optic 25 WW to a DMX controller using a standard DMX serial connection If using other DM
18. of less than five points are not significant e g light sources with 80 and 84 CRI are essentially the same 3 If color appearance is more important than color fidelity do not exclude white light LEDs solely on the basis of relatively low CRI values Some LED products with CRIs as low as 25 still produce visually pleasing white light 4 Evaluate LED systems in person and if possible on site when color fidelity or color appearance are important issues Source DOE publication PNNL SA 56891 January 2008 16 llumipod Inground Tri 3 IP Optic 25 WW User Manual Rev 5 ILUMINARC reserves the right to use its own discretion to repair or replace returned product s Always keep the original box and all packaging material as you will need those to ship the product back to ILUMINARC Contact Us ARC Technical Information Returns Procedure You must send the merchandise prepaid in the original box and with its original packing and accessories ILUMINARCO will not issue call tags Call ILUMINARC and request a Return Merchandise Authorization Number RMA before shipping the product Be prepared to provide the model number serial number and a brief description of the cause for the return The user must clearly label the package with an RMA ILUMINARC will refuse any product returned without an RMA DO NOT write the RMA directly on the box Instead write it on a properly affixed label Once you r
19. r fire Never connect the llumipod Inground Tri 3 IP Optic 25 WW to a rheostat variable resistor or dimmer circuit even if the rheostat or dimmer channel serves only as a O to 100 switch N connect the llumipod Inground Tri 3 IP Optic 25 WW to a power line with the proper voltage and frequency as per the specifications in this User Manual or on the product s sticker Make sure to The listed current rating indicates the maximum current draw during normal operation If you choose to bury the power or O signal distribution boxes make sure that they are IP67 rated or greater Installation AC Power The Ilumipod Inground Tri 3 IP Optic 25 WW has an auto ranging power supply that works with an input voltage range of 100 240 VAC 50 60 Hz Make sure that you are connecting this product to the proper voltage as per the specifications in this User Manual or on the product s sticker Power Consumption To determine the power requirements for the Ilumipod Inground Tri 3 IP Optic 25 WW refer to the label affixed to the side of the product Alternatively you may refer to the Technical Specifications The listed current rating indicates the maximum current draw during normal operation AC Plug The Ilumipod Inground Tri 3 IP Optic 25 WW comes with a bare ended power input cord for hardwired installation Use the table and the illustration below to wire a plug Connection Wire U S Screw Co
20. r purpose without its written consent Document Printing For better results print this document in color on letter size paper 8 5 x 11 in double sided If using A4 paper 210 x 297 mm configure your printer to scale the content of this document to A4 paper Intended Audience Any person in charge of installing operating and or maintaining the Ilumipod Inground Tri 3 IP Optic 25 WW should read all of both the guide that shipped with it and this User Manual before installing operating or maintaining this product Disclaimer ILUMINARC believes that the information contained in this manual is accurate in all respects However ILUMINARC assumes no responsibility for any error or omissions in this document ILUMINARC reserves the right to revise this document and to make changes from time to time in the content hereof without obligation of ILUMINARCO to notify any person or company of such revision or changes This does not constitute in any way a commitment by ILUMINARC to make such changes ILUMINARC may issue a revision of this manual or a new edition of it to incorporate such changes Document Revision The Ilumipod Inground Tri 3 IP Optic 25 WW User Manual Rev 5 supersedes all previous versions of this manual Please discard any older versions of this manual you may have whether in printed or electronic format and replace them with this version Author Date Editor Date D Couppe 5 1 15 llumipod Inground Tri 3 IP
21. rounding can cause greater accumulation of dirt on the p y or p y arty 8 8 D a optics product s optics requiring more frequent cleaning and glass surfaces carefully To clean a product after cleaning them Disconnect the product from power Wait until the product is at room temperature Use a vacuum or dry compressed air and a soft brush to remove dust collected on the If you still external surfaces al Clean all external glass optics and glass surfaces with a mild solution of glass cleaner or problems after isopropyl alcohol and a soft lint free cotton cloth or lens cleaning tissue ad q the Apply the solution directly to the cloth or tissue and wipe any dirt and grime to the outside e UNA DO edge of the lens Gently polish the external glass surfaces until they are free of haze and Technical Support lint Product Repairs ILUMINARC strongly advises you against attempting any repairs to this product unless you are an authorized ILUMINARC technician ILUMINARC presents the information contained in the Troubleshooting Guide as potential solutions only In most cases opening the product s housing will invalidate its warranty llumipod Inground Tri 3 IP Optic 25 WW User Manual Rev 5 13 aa b gt A EP 4 PE 7 Bi y i LJ 1 VAP ls Al Technical Information Il LJIVII Troubleshooting Guide Symptom Cause s Action s Check total load placed on the electrical ircui Excessive circuit load a Circuit br
22. se to this product while it is operating Power and Wiring Always make sure that you are connecting this product to the proper voltage as per the specifications in this User Manual or on the product s sticker CAUTION When transferring product from extreme temperature environments e g cold truck to warm humid ballroom condensation may form on the internal electronics of the product To avoid causing a failure allow product to fully acclimate to the surrounding environment before connecting it to power Never connect this product to a dimmer pack Make sure that the power input cable is not cracked crimped or damaged Never disconnect this product by pulling or tugging on the power input cable Operation The maximum ambient temperature is 113 F 45 C Do not operate this product at a higher temperature In case of a serious operating problem stop using this product immediately llumipod Inground Tri 3 IP Optic 25 WW User Manual Rev 5 ILUMINARG Product Description 2 Product Description The Ilumipod Inground Tri 3 IP Optic 25 WW is a wash light intended for in ground installation The product consists of a cast aluminum body containing a power supply control unit drive over rated glass lens cover and tri emitter LEDs Features 1 channel warm white LED in ground wash light Operating mode 1 channel Dimmer Five distinct dimming curves IP67 stainless steel gland nuts for cable entry Remotely addressable with
23. t in a menu llumipod Inground Tri 3 IP Optic 25 WW User Manual Rev 5 1 Introduction There are no user serviceable parts inside this product Any reference to servicing you may find in this User Manual will only apply to properly certified ILUMINARC technicians Do not open the housing or attempt any repairs unless you are certified to do so Please refer to all applicable local codes and regulations for the proper installation of this product Keep this manual for future consultation If you sell this product to another user make sure that they also receive this manual In the unlikely event that your D llumipod Inground Tri 3 IP Optic 25 WW may require service please contact ILUMINARC Technical Support Safety Notes Please read all the following Safety Notes carefully because they include important information on how to install use and maintain this product safely Personal Safety Avoid direct eye exposure to the light source while the product is on Always disconnect this product from its power source before servicing Always connect this product to a grounded circuit to avoid the risk of electrocution Do not touch this product s housing when operating because it may be very hot Mounting and Installation This product is for outdoor use and can be submerged IP67 However do not submerge deeper than 1 m for more than 30 minutes Make sure there are no flammable materials clo
Download Pdf Manuals
Related Search