User Manual for the JNF99FL system-board
Contents
1. 33 SYSFAN1 Smart Mode and SYSFAN2 Smart Mode to set respectively for value in Full Speed Temp Idle Temp and Idle Speed Duty 5V OVP 12V OVP Vcc3V OVP Use this item to select a value for 5V OVP 12V OVP Vcc3V OVP from the optional setting range CPU Temperature System Temperature SYSFAN1 SYSFAN2 Speed Vcore NB1 05V 5VSB VDIMM 5V 12V 5 Vcc3V 3VSB VBat This will show the CPU FAN System voltage chart and FAN Speed etc 3 11 Miscellaneous Control Copyright 1905 2009 American Heqatrends Inc Niscellaneous Control eS n F T nm cI rr s spread Spectrum Disabled Help Linear Clock 100 Current DRAM Clock is DRAM Clock at Next oot Auto Current Host PCI Clock ia Disabled Hoat PCI Clock at Next Poot 200 Enabled 11 Entor Select Ualue ESC Exit Fi Goneral Help Prev lous Values Fo iptinized Defaults Defaults Spread Spectrum The optional settings are Enabled Disabled Linear PCIEX Clock The optional settings are from 100 to 200 DRAM Clock at Next Boot This item allows you to set DRAM clock The optional settings are Auto 66 2 800MHz Host PCl Clock at Next Boot The optional settings are from 200 to 600 3 12 Password Setting You can set either supervisor or user password or both of them The differences are Su2. 2 3 Short Clear CMOS CMOS Clear Setting 2 2 Connectors and Headers 2 2 1 Connectors 1 VO Panel Connector PS 2 Port RJ 45 LAN Port Keyboard Port mH RJ 45 LAN Port Line OUT VGA Port USB 2 0 Ports USB 2 0 Port Line IN 2 Serial ATA PortS 1 SATA2 SAT A3 SATAA SAT A5 SATA SATA6 USB 3 0 Port Connector 2 2 2 Headers 1 Front Panel Audio Line Out MIC In Header 9 pin FP_AUDIO1 header connects to front panel Line out MIC In with cable s amp e 63 HHHH Sense FB Lineout2 L 44 N 5 H Line Out MIC Headers CD AUDIO In Header 4 CDIN1 CDIN header is for CD Audio Input signal Please connect itto CD ROM CD Audio output connector n gt oS gt gt Sp Terr CD Audio In Headers 3 USB Port Headers DIE USB3 USB4 USB5 20 lt gt n USB 3 4 5 Header 4 Speaker connector SPEAK This 4 pin header is to connect the case mounted speaker See the figure below 5 Power LED PWRLED The Power LED is light on while the system power is on Connect the Power LED from the system case to this pin TENEMENT PWRLED 0
3. ec Enn 2 3 closed Inverter 5V select JP3 JP4 1 2 closed UL1 USB1 Power On Disabled default JP4 1 5 J JP5 3 USB3 Power on Function Setting JP5 JP5 2 3 closed USB3 Header Power On Enabled 6 J aid ok pin m PCI Power VCC 3 3V Dual 3 3 V Function Select JP6 TH 1 2closed MINI PCI E VCCz 3 3V JP6 CUM 2 3closed MINI PCI E VCC Dual 3 3V p B m H 8 F t BE B BB 44 p I N Sp 1 LIO TEH 1 2 closed RS232 3 4 closed 12V 5 6 closed 5V 1 2 closed RS232 3 4 closed RS485 5 6 closed 85422 JP11 1 2 closed USB 4 5 Header Power On Disabled default S JP11 1 3 po 2 3 closed USB 4 5 Header Power On Enabled JBAT 1 3 1 2 Short Normal Ud 842511111114 1 3
4. a W 6 Front Panel Header JW FP PWRLED PWRBTN 5 8 gt 9 M 7 Bo 2809 lt H VPE a CH il Lu ail 6 0 uses Pin1 GND Pin2 12V fan power Pin3 Fan Speed SYSFAN 1 moo 1 3 CPUFAN 1 SYSFAN2 1 3 T S T B B ee FERREE B B B B B B B B B mm LL Tu 5 D 4 i E x ap 8 838 72220 115 9 ic m mb aslo dd RE 8 Serial Port CONDECION Pin female 2 EOCEEN ATTY 22 2 LU ER HN TT mismes 2 e 4 TX RXCOM 2 4 Pin 1 3 COM Header 10 LVDS Headers 32 Pin LVDS SPDIF O gt 22 Ja o CEHHEHIH m gt i IE Pin 2 ooooooooooooooo Pin 1 LVDS Header 11 LVDS Inverter headers INVERTER Pin 1 and pin2 VCC of inverter pin4 and GND Pi
5. lt Yalue F10 Sage ESC Exit Fil General Help Fo Previous Values F Untinized Defaults Peistandard Defaults 3 7 2 Onboard Device Function 0 1905 2009 Inc Unboard Device Function board LANL Controller Enabled Help len Unboard LANL Disabled Inboard LANZ Controller Enabled 1 3118 Disabled High Definition Audio Enabled Enabled Host Controller 12 198 Ports Disabled 1511 4 0 Function Enab Led US 2 0 Operation Mode US 3 0 Controller Mode Enabled Handle Enabled USI Keyboard Legacy Support Enabled 138 House Legacy Support Disabled US Storage Legacy Support Enabled 138 Hass Storage Device Configuration EntersSelect FlO Save ESC Exit FliGeneral Help Fo Previous Values Fo Defaults Pirstandard Defaults Onboard LAN1 2 Controller The optional settings are Enabled Disabled Onboard LAN1 2 BootROM The optional settings are Enabled Disabled High Definition Audio This item allows you to decide to auto disable the chipset family to support HD Audio The settings are Auto Disabled USB 2 0 Operation Mode The settings are FullSpeed HiSpeed USB Host Controller The optional settings Disabled 2 USB ports 4 USB ports 6 USB ports 8 USB ports 10 USB ports 12 USB ports USB 2 0 Function The optional settings are Enabled Disab
6. Copyright 1905 2009 Hegatrends Inc CPU Feature Hyper Threading Technology Enabled Help Limit CPU Disabled Execute Disable Tit Capablil Enabled Enabled for Windows and Linuxi 05 114111 ed for Hyper Threading Technology and disab led for other 05 115 not optimized uper Threading Techn ology Enter Select Ualue FliGeneral Help LER i fy 7418 Threading Technolegy Enabled for Windows XP and Linux4 OS optimized for Hyper Threading Technology and disabled for other OS OS not optimized for Hyper Threading Technology Ec Limit CPU MaxUal The optional settings are Disabled Enabled Execute Disable Bit Capabill The optional settings are Disabled Enabled When disabled force the XD feature Flag to always return 0 3 6 Advanced Chipset Features The Advanced Chipset Features Setup option is used to change the values of the chipset registers These registers control most of the system options in the computer Copyright C 1905 2009 American DRAM Timing Settings by SPD Initate Graphic Adapter 100 Hode Select LUDS ADDON CARD Suppor Enter Select DRAM Timing Settings SPD fidvanced Chipset Features Ui li R E 24 Hegatre nds
7. 1 3 Layout Diagram PS 2 Port 45 LAN Port Keyboard Port N 45 LAN Port B 5 Line OUT OK MIC IN VGA Port USB 2 0 Ports USB 2 0 Port Line IN USB 3 0 Port PS 2 Keyboard over USB 3 0 Port kel sYSFANI if Serial Port Intel CPU 8 Over VGA Port E Parallel Header 7 LVDS Inverter E 2 3 EB RJ 45 over spes 2e E DDRIII 800 USB 2 0 Port Jh EEEEEEEEREEEEEEE LVDS Header SODIMMs E LAN Chip SODIMMI SODIMM2 RJ 45 P 3 45 Port gt P Ti Intel ICH9R Chipset 4 d ND CPUFAN USB 2 0 Port 184 20 0 Por i 11 i 2 Header EN Line OUT ea P Connectors TX RX Line IN d Mini PCIE Slot 4 Audio Codec Chip MIC IN EST RAT 22 8888888889838585 88888888 GPIO i Front Pane 1 LE gebe Pover LED Header FP_AUDIO1 1 O Audio Header 69 iE ia Front Panel Header PCI slot SYSFAN2 USB Headers Daughter Card Connectors 8 Mbit Flash Rom BIOS Jumper __ Jumper Description 3 pin Block 2 ________ 5 5V 3 3V Select Block 3 pin
8. 2 HEADERS u 12 CHAPTER 3 INTRODUCING BIOS ENTERNING SEU UP EEEa 19 c 19 453 THE MAIN MEN 19 3 4 STANDARD BIOS FEATURES Calvum rasa eS cs 21 35 ADVANCED BIOS FEATURBDES 23 35551 OPU FEATURE 24 3 6 ADVANCED CHIPSET FEATURES LLULLU L u 25 3 7 INTEGRATED PHERIPHRALS uu uuu u 26 35771 ONBOARD SATA FUNC TION uuu ll l l l l l 27 3 7 2 ONBOARD DEVICE FUNCTION 28 3 7 3 ONBOARD SUPER IO FUNCTION 29 3 8 POWER MANAGEMENT SETUP J J J 30 99 PNPJIPGICONFIGUHATIONY u LLULLU 32 3410 HEACIH STATUS u u inn pati u uama Qux EHE SE Ex 32 3 11 MISCELLANEOUS CONTROL J JJ 34 9 12 PASSWORD uuu EU ie uM 35 3 13 LOAD OP
9. Block 3 pin Block 3 pin Block 3 pin Block 6 pin Block 6 pin Block 3 pin Block 3 pin Block Connectors Connector Description __ KB from UK1 PS2 Keyboard Connector 6 pin Female USB from UK1 USB 3 0 Ports 1 Video Graphic Attach Connector USB1 USB 2 0 Port 4 pin Connector AUDIO Line Out Line MIC Audio 3 phone Jack Connector ATXPWR ATX Power Connector 24 pin Block SATA1 SATA6 Serial Connectors 7 pin Connector LAN1 RJ 45 LAN Connector 8 pin Connector Headers Header Description 9 pin Block 4 pin Block 10 pin Block 9 pin Block 4 pin Block 3 pin Block JW FP Front Panel Header 9 pin Block PWR LED HD LED PWR LED HD LED Power Power Button Reset Button Reset 3 pin Block 25 pin Block 9 pin Block 4 pin Block 32 pin Block 7 pin Block 50 pin 2 Block Chapter 2 Hardware Installation 2 1 Jumper Setting 3 pin K B USB Power on Function Setting 1 3 1 2 Closed K B USB Power On Disabled default 1 3 2 3 closed K B USB Power On Enabled JP2 1 3 1 2 closed LVDS PVCC 5V O en _ Ep TA JP2 EM _ 1 3 2 3 closed LVDS PVCC 3 3V IN 3 3 Inverter power 5V 12V Select 1 me 1 2 closed Inverter 12 selected JP3
10. UTE APIC Enab Led Protection HPS VYerston Control for 05 1 4 Enter Select FLO Save ESC Exit Fi General Help Values Virus Warning The selection Allow you to choose the VIRUS Warning feature for IDE Hard Disk boot sector protection If this function is enabled and someone attempt to write data into this area BIOS will show a warning message on screen and alarm beep Disabled default No warning message to appear when anything attempts to access the boot sector or hard disk partition table 23 Enabled Activates automatically when the system boots up causing a warning message to appear when anything attempts to access the boot sector of hard disk partition table Quick Power On Self Test This item allows BIOS to skip certain tests while booting This will decrease the time needed to boot the system The optional settings Disabled Enabled Boot Up NumLock Status The default value is On On default Keypad is numeric keys Off Keypad is arrow keys APIC Mode Use this item to include ACPI APIC table pointer to ESDT pointer list The optional settings are Disabled Enabled MPS Version Control for OS This option is only valid for multiprocessor motherboards as it specifies the version of The Multiprocessor Specification MPS that the motherboard will use 3 5 1 CPU Feature
11. in Uptions 81711111 Disabled Enabled Disabled FlO Save LU Standard The optional settings are Disabled Enabled Initate Graphic Adapter The optional settings are 1GD PCIE IGD Select which graphic controller to use as the primary boot device 25 IGD Mode Select Use this item to select the amount of system memory used by the internal graphics device The optional settings Disabled Enabled 8MB LVDS ADDON CARD Support The optional settings are Disabled Enabled 3 7 Integrated Peripherals Copyright 1995 2009 American Hegalrends Inc Integrated Peripherals H Unboard SATA Function Pross Enter Help Iten k Unboard Device Function Press Enter 22111171 Super IU Function Press Enter FUR Statue alter PWR Always OFF Enter Select 6 Fi General Previous Values FoiUptinized Defaults Standard Defaults PWR Status after PWR Failure The optional settings are Always off Always on Former Status 3 7 1 Onboard SATA Function Copyright 2 1905 2009 Awerican Hegalrends Inc Unboard SATA Function ee as B gt T TT T tos Configure SATANI as IDE Help ptions DE Marb eee ee ee SS V P gt s lt sa F Enter Select
12. shutdown Temperature 10111471 50 00 124 UUP Ucc3U OUP Temper CPURAN speed aped 1 050 Disabled k Smart FAN ont iyurat Long Press Enter Disabled Disabled Disabled Tul UR MALUM aturi 9 10271 1 152 U 1 048 U 1 517 0 11 100 Sel Ui l H Save lous Values Fo Uptiaized Defaults Help Uptions _ Disabled 60 C 140 F T6 C 167 1 ESC ExIt FliGeneral th dp Standard Defaults k U Uce Wall Ullal 1 944 Y 11 010 9 1 216 1 1 210 Select Value FLO Save Prey lous Values Shutdown Temperature This item can let users setting the Shutdown temperature when CPU temperature over this setting the system will auto shutdown to protect CPU CPU Thermal Throttling The optional settings are Disabled Enabled When it is set as Enabled user could set value for CPU Thermal Throttling Temp CPU Thermal Throttling Duty and CPU Thermal Throttling Beep Smart Fan Configuration Press Enter to set certain values for the following three items CPUFAN Smart Mode ESC Exit Fi Genoral Help Foitiptinized Defaults FiiStandard
13. TECHNICAL MANUAL Of Intel Pine Trail D amp ICH9R Chipset Based Mini ITX for ATOM Processor NO G03 NF99 F Revision 1 0 Release date March 2011 Trademark Specifications and Information contained in this documentation are furnished for information use only and are subject to change at any time without notice and should not be construed as a commitment by manufacturer Environmental Protection Announcement Do not dispose this electronic device into the trash while discarding minimize pollution and ensure environment protection of mother earth please recycle TABLE OF CONTENT ENVIRONMENTAL SAFETY INSTRUCTION iii USER 2 NOICE MANUAL REVISION INFORMATION JJ eee CHAPTER 1 INTRODUCTION THE MOTHERBOARD 1 FEATUREOFMOTHERBOARD uu uu ULU 1 142 SPECIFICATION u u u M 2 1 3 DIAGRAM u u c 3 CHAPTER 2 HARDWARE INSTALLATION 2 1 JUMPER uuu grec a 7 2 2 CONNECTORS AND HEADERS J JJ 11 2 2 1 CONNECTOR Sisic nese ee eee ene MUN RUM ne S ARR NEN UNIES RUE 11 2 2
14. TICE COPYRIGHT OF THIS MANUAL BELONGS TO THE MANUFACTURER NO PART OF THIS MANUAL INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT MAY BE REPRODUCED TRANSMITTED OR TRANSLATED INTO ANY LANGUAGE IN ANY FORM OR BY ANY MEANS WITHOUT WRITTEN PERMISSION OF THE MANUFACTURER THIS MANUAL CONTAINS ALL INFORMATION REQUIRED TO USE THIS MOTHER BOARD SERIES AND WE DO ASSURE THIS MANUAL MEETS USER S REQUIREMENT BUT WILL CHANGE CORRECT ANY TIME WITHOUT NOTICE MANUFACTURER PROVIDES THIS MANUAL AS IS WITHOUT WARRANTY OF ANY KIND AND WILL NOT BE LIABLE FOR ANY INDIRECT SPECIAL INCIDENTAL OR CONSEQUENTIAL DAMAGES INCLUDING DAMAGES FOR LOSS OF PROFIT LOSS OF BUSINESS LOSS OF USE OF DATA INTERRUPTION OF BUSINESS AND THE LIKE PRODUCTS AND CORPORATE NAMES APPEARING IN THIS MANUAL MAY OR MAY NOT BE REGISTERED TRADEMARKS OR COPYRIGHTS OF THEIR RESPECTIVE COMPANIES AND THEY ARE USED ONLY FOR IDENTIFICATION OR EXPLANATION AND TO THE OWNER S BENEFIT WITHOUT INTENT TO INFRINGE Manual Revision Information Reversion Revision History Date 1 0 First Edition March 201 1 Item Checklist Motherboard Users Manual DVD for motherboard utilities Cable s 1 O Back panel shield IV 1 1 Chapter 1 Introduction of the Motherboard Feature of motherboard Intel Pine Trail D and ICH9R chipset Onboard Intel Atom CPU with low power consumption never denies high performance Support DDRIII SODIMM 800 MHz up to Onboard d
15. TIMIZED STANDARDDEFAULLTS 36 3 14 SAVE AND EXIT SETUP EXIT WITHOUT SAVING 36 ii CAUTION Environmental Safety Instruction Avoid the dusty humidity and temperature extremes Do not place the product in any area where it may become wet 0 to 60 centigrade is the suitable temperature The figure comes from the request of the main chipset Generally speaking dramatic changes in temperature may lead to contact malfunction and crackles due to constant thermal expansion and contraction from the welding spots that connect components and PCB Computer should go through an adaptive phase before it boots when it is moved from a cold environment to a warmer one to avoid condensation phenomenon These water drops attached on PCB or the surface of the components can bring about phenomena as minor as computer instability resulted from corrosion and oxidation from components and PCB or as major as short circuit that can burn the components Suggest starting the computer until the temperature goes up The increasing temperature of the capacitor may decrease the life of computer Using the close case may decrease the life of other device because the higher temperature in the inner of the case Attention to the heat sink when you over clocking The higher temperature may decrease the life of the device and burned the capacitor iii USER S NO
16. by Suspend Suspend Time out Use this item to select the specified time for system to go into suspend Power Button Mode Use this item to go into On Off or Suspend when power button is pressed ERP EUP Function The optional settings are Enabled Disabled When set as Disabled the following sub items shall appear Wake Up by PCI Card Power On by Ring Wake Up by USB from S3 S4 PS2 KB MS Wake Up from S3 S5 Resume On RTC Alarm User can set them as Enabled or Disable for to enable or disable respective functions 31 3 9 PnP PCI Configurations 5 Copyright 1905 2009 American Hegatrends In PnPZPCI Configurations k LRU Resources Press Enter Help IUNFIUFTM Palette 91111111 Enter Select Ualue PI0 Sage ESC Exit Fil General Help Proy lugs Fetotandard 0 IRQ Resources Press Enter to view IRQ availability Available Specified IRQ is available to be used by PCI PnP devices Reserved Specified IRQ is reserved for use by legacy ISA devices PCI VGA Palette Snoop The optional settings are Enabled Disabled Enabled to inform the PCI devices that an ISA graphics device is installed in the system so the card will function correctly 3 10 PC Health Status This section shows the Status of you CPU Fan and Warning for overall system status This is only available if there is Hardware Monitor onboard PC Health Status
17. e this item to allow BIOS to select parallel port base adresses Parallel Port Mode The optional settings are Normal Bi Directional ECP EPP ECP amp EPP Watchdog Timer Select This item is used to activate the watchdog function The optional settings are Enabled Disabled When set as Enabled The following sub items shall appear WatchDog Timer Val User can type a number in the range of 4 to 255 WatchDog Timer Unit The optional settings are Sec Min 3 8 Power Management Setup The Power Management Setup allows you to configure your system to most effectively save energy saving while operating in a manner consistent with your own style of computer use Copyright 1995 2009 Hegatrends Inc Power Managenent Setup ACF Suspend Type Help ten Video Power Down Hodo Disabled Suspend Tine Cut Disabled SS m Power Hutton Hode ERP Function Disabled Disabled Wake Up hu PCI Card Disabled Enabled Power Un by Ring Disabled Make Up by USI from 52059 Disabled I32 KHB HS Make Up from 51 55 Disabled On RTC Alarm Disabled Enter Select 7 Ualue ESCiExIC Help Previous Values FoUptinized Defaults ACPI Suspend Type Users can select the state used for system suspend The optional settings S1 POS S3 STR Video Power Down Mode The optional settings Disabled Stand
18. led USB 2 0 Operation Mode Use this item to configure the USB 2 0 controller in HiSpeed 480Mbps or FullSpeed 12Mbps USB 3 0 Controller Mode Use this item to enable USB 3 0 legacy support BIOS XHCI Hand The optional settings are Enabled Disabled USB Keyboard Legacy Mouse Legacy Storage Legacy Support Select enabled if your system contains a Universal Serial Bus USB controller and you have a USB mouse keyboard USB storage device The settings are Enabled Disabled 3 7 3 Onboard Super IO Function 0 2275 2003 LETTERE ERN Onboard Super IO Function P32 KHB HS SWAP Select Help TOUT Serial Port Address Serial Port2 Hodi emu D p 5405 Select 0 Disabled 8774 Keyboard Firs Parallel Port Address Vil Mouse n Parallel Port Mode WatchDog Timer Control Disabled TleesMove Enter Select FlO Save ESC Exit Pl General Help roiPrevlows Va lies 1 1 1 1 ri Defaulte 29 PS2 KB MS SWAP Select The optional settings are Keyboard First Mouse First Serial Port 1 2 Address This item allows BIOS to select base addresses for serial port 1 2 Serial Port 2 Mode The optional settings are Normal IrDA 1 6us IrDA 3 16 bit Serial Port 2 RS485 Select The optional settings are Disabled RS232 Enabled RS485 Parallel Port Address Us
19. n5 Backlight Brightness 20 9522523 gt gt 8 50 e GPIO CON 0 Pin 1 RARE 6656 GPIO CON Header Chapter 3 Introducing BIOS Notice The BIOS options in this manual are for reference only Different configurations may lead to difference in BIOS screen and BIOS screens in manuals are usually the first BIOS version when the board is released and may be different from your purchased motherboard Users are welcome to download the latest BIOS version form our official website The BIOS is a program located on a Flash Memory on the motherboard This program Is a bridge between motherboard and operating system When you start the computer the BIOS program will gain control The BIOS first operates an auto diagnostic test called POST power on self test for all the necessary hardware it detects the entire hardware device and configures the parameters of the hardware synchronization Only when these tasks are completed done it gives up control of the computer to operating system OS Since the BIOS is the only channel for hardware and software to communicate it is the key factor for system stability and in ensuring that your system performance as its best In the BIOS Setup main menu of Figure 3 1 you can see several options We will explain these options step by step in the following pages of this chapter but let us first see a short description of the fu
20. nction keys you may use here Press Esc to quit the BIOS Setup Press T4 lt gt up down left right to choose in the main menu the option you want to confirm or to modify e Press lt 10 gt when you have completed the setup of BIOS parameters to save these parameters and to exit the BIOS Setup menu e Press Page Up Page Down or keys when you want to modify the BIOS parameters for the active option 16 3 1 Entering Setup Power on the computer and by pressing lt Del gt immediately allows you to enter Setup If the message disappears before your respond and you still wish to enter Setup restart the system to try again by turning it OFF then ON or pressing the RESET button on the system case You may also restart by simultaneously pressing Ctrl lt Alt gt and Delete keys If you do not press the keys at the correct time and the system does not boot an error message will be displayed and you will again be asked to Press Del to enter Setup 3 2 Getting Help Main Menu The on line description of the highlighted setup function is displayed at the bottom of the screen Status Page Setup Menu Option Page Setup Menu Press F1 to pop up a small help window that describes the appropriate keys to use and the possible selections for the highlighted item To exit the Help Window press Esc 3 9 Main Menu Once you enter AMI BIOS CMOS Setup Utility the Main Menu Figure 3 1 will appea
21. pervisor password enter and change the options of the setup menus User password Can only enter but do not have the right to change the options of the setup menus When you select this function the following message will appear at the center of the screen to assist you in creating a password ENTER PASSWORD Type the password up to eight characters in length and press Enter The password typed now will clear any previously entered password from CMOS memory You will be asked to confirm the password Type the password again and press Enter You may also press Esc to abort the selection and not enter a password To disable a password just press Enter when you are prompted to enter the password A message will confirm that the password will be disabled Once the password is disabled the system will boot and you can enter Setup freely PASSWORD DISABLED When a password has been enabled you will be prompted to enter it every time you try to enter Setup This prevents an unauthorized person from changing any part of your system configuration Additionally when a password is enabled you can also require the BIOS to request a password every time your system is rebooted This would prevent unauthorized use of your computer You determine when the password is required within the BIOS Features Setup Menu and its Security option If the Security option is set to System the password will be required both at boot and at en
22. r on the screen The Main Menu allows you to select from fourteen setup functions and two exit choices Use arrow keys to select among the items and press Enter to accept or enter the sub menu Copyright 1905 2009 American Hegatrends Inc Standard 0103 Features Miscellaneous Control Advanced MUS Features Load Optimized Defaults Advanced Chipset Features Load Standard Defaults Integrated Peripherals sot Supervisor Password Power Management setup aet User Password Cont Igqurat Long save A Exit Setup PC Health Status Exit Without Saving Enter Select iValue FIO Saye ESC Exit FliGeneral Help Fo Previous Yalues Fo Uptimnized Defaults Pi Standard Defaults u02 0 C Copright 1905 2010 Ine Figure 3 1 Standard BIOS Features Use this Menu for basic system configurations Advanced BIOS Features Use this menu to set the Advanced Features available on your system Advanced Chipset Features Use this menu to change the values in the chipset registers and optimize your system s performance Integrated Peripherals Use this menu to specify your settings for integrated peripherals Power Management Setup Use this menu to specify your settings for power management PnP PCI Configurations Use this menu to specify your settings for PnP and PCI configurations PC Health Status This entry shows your PC health status Miscellaneous Control Use this menu to specify you
23. r settings for Miscellaneous Control Load Optimized Detaults Use this menu to load the BIOS default values these are setting for optimal performances system operations for performance use Load Standard Defaults Use this menu to load the BIOS default values for the minimal stable performance system operation Set Supervisor Password Use this menu to set supervisor password Set User Password Use this menu to set user password Save amp Exit Setup Save CMOS value changes to CMOS and exit setup Exit Without Saving Abandon all CMOS value changes and exit setup 3 4 Standard BIOS Features The items in Standard CMOS Setup Menu are divided into several categories Each category includes no one or more than one setup items Use the arrow keys to highlight the item and then use the lt PgUp gt or lt PgDn gt keys to select the value you want in each item Copyright C 19405 2009 finer Hegatrends Inc Standard BIOS Foatures yaten Date Tue 04 15 2011 Help Iten yaten Tine 00 15 15 Use CENTER TAHI 51141 to k SATA Channel 1 Not Detected select Field SATA Channel 2 Not Detected SATA Channel 2 Not tod Use Cel to b SATA Channel 4 Not Detected configure system Date SATA Channel 5 Not Detected SATA Channel 0 Not Detected Henory 3120 EnteriSelect Value ESC Exit Fi General Help Previous Values Fo Uptinized Delault
24. s Defaults System Date The date format is lt day gt lt month gt lt date gt lt year gt Day Day of the week is from Sun to Sat determined by BIOS Read only Month month is from Jan through Dec Date The date from 1 to 31 can be keyed by numeric function keys Year The year depends on the year of the BIOS System Time The time format is hour minute second SATA 1 5 2 SATA3 SATA4 SATA 5 SATA6 While entering setup BIOS auto detects the presence of harddisk devices This displays the status of auto detection of harddisk devices Type The optional settings are Not Installed Auto CD DVD and ARMD LBA Large Mode The optional settings are Auto Disabled Disabled disables LBA mode Auto enables LBA Mode if the devices support it and the device is not already formatted with LBA Mode disabled Block Multi Sector Transfer The optional settings are Disabled and Auto Disabled The Data transfer from and to the device occurs one sector at a time Auto The Data transfer from and to the device occurs multiple sectors at a time if the device supports it 32 Bit Data Transfer the optional settings are Disabled and Enabled 3 5 Advanced BIOS Features Copyright C 1905 2009 American Hegatrend Advanced BIOS Features Virus Warning Ite k Feature Prosa Ento Quick Power Un Self Test Enabled Enable Disable Hoot Up Hunlock Status Ult foot sector
25. try to Setup If set to Setup prompting only occurs 35 when trying to enter Setup 3 13 Load Optimized Standard Defaults Load Optimized Defaults When you press Enter on this item you get a confirmation dialog box with a message similar to Load Optimized Defaulta Cancel Pressing OK loads the default values that are factory settings for optimal performance system operations Load Standard Defaults When you press Enter on this item you get a confirmation dialog box with a message similar to Load Standard Dafaulta Canca l Pressing lt OK gt loads the default values that are factory settings for stable performance system operations 3 14 Save amp Exit Setup Exit Without Saving Save and Exit Setup When you press lt Enter gt on this item you get a confirmation dialog box with a message similar to Save configuration changes and exit setup Cancel Pressing lt OK gt save the values you made previously and exit BIOS setup Exit Without Saving When you press lt Enter gt on this item you get a confirmation dialog box with a message similar to Discard changes and exit setup KI Cancel Pressing OK to leave BIOS setting without saving previously set values
26. ual Intel 82574L PCI E Gigabit Ethernet LAN Integrated VIA VT1705 6 channel HD audio CODEC oupport USB 3 0 data transport demands Support 5232 422 485 Support PCI slot and Mini PCIE slot Support CPU Smart FAN Supports ACPI S3 Function Support watchdog function 1 2 Specification Spec X Description Design form factor PCB size 17 0x17 0cm Chipset Intel Pine Trail D ICH9OR Embedded CPU e Intel Atom CPU DDRIII SODIMM slot x2 Memory Socket e Support 800 MHz DDHIII SODIMM e Expandable to 4 GB e 32 bit PCI slot x 1 e Mini PCIE slot x1 Support six internal serial Gb s connectors Integrate SATAN le Support RAID 0 1 5 10 Dual LAN e Integrated dual Intel WG82574L PCI E Gigabit LAN chip e Support Fast Ethernet LAN function of providing 10Mb 100Mb 1000Mb Ethernet data transfer rate Mudo Autioarverandutityinduded e Audio driver and utility included BIOS AMIBMBFlaashROM 00000000 Multi I O e 5 2 keyboard connector x1 USB 3 0 port x2 Serial port connector x1 VGA port connector x1 USB 2 0 port x 3 and USB 2 0 header x3 RJ 45 LAN connector x2 Audio connector x3 Line in Line out MIC Parallel port header x1 Serial port header x1 and RS232 422 RS485 header 1 L VDS header x1 and LVDS inverter x1 GPIO header x1 Front panel audio header x1 CDIN header x1 Expansion Slot Speaker header x1 e PWRLED header x e Front panel header x1
Download Pdf Manuals
Related Search