Sensixx B45L - Kitchens dela Lumina
Contents
1. This steam station has a unique i Temp function When switching on the appliance it automatically sets an appropriate combination of temperature and steam which is suitable for all fabrics that can be ironed The i Temp function prevents clothes from being damaged due to an unsuitable temperature being selected The i Temp function does not apply to fabrics that cannot be ironed Please check the garment care label for details or try ironing on a part of the cloth not visible normally AntiShine Em antiShine function This steam station has a unique AntiShine function If this function is selected and the steam release button is regularly pressed the risk of shiny marks on the garment due to the ironing is reduced How to use the steam station 1 When the steam station is plugged in and main power button set to the on position button illuminated the display 8 lights up and shows all icons for 2 seconds ey AN iTemp secure ey UN a temp antiShine M A clean Model dependent gt gt 2 After that time the appliance shifts automatically to the i Temp setting The icon will flash until the temperature and steam settings are reached 3 Temperature settings Zi temp M AD AN Temperature level selection touch icon is used to change the temperature of the iron soleplate Automatic temperature selection of the iron soleplate It is suitable for an2. been activated Indicates flashing that the water tank 1 is empty and must be filled Indicates flashing that e 138 the boiler and the filter 12 must be rinsed 6 Beep activation deactivation You can activate or deactivate a beep which may be heard rd touching the icons on the display 8 To do this simply touch the L land icons at the same time for 3 seconds After this time a long beep will be emitted indicating that the beep has been activated or deactivated sy Gc Preparations cm before ironing For details of the following actions please see the related chapters of this user manual 1 Release the iron from its SecureLock system 10 by pulling the lever located at the heel of the iron backwards 2 Remove any label or protective covering from the soleplate 16 3 Place the appliance horizontally on a solid stable surface You may remove the iron pad 2 from the appliance and place the iron on it on another solid stable horizontal surface 4 Fill the removable water tank 1 If the tank is removed three beeps may be heard Model dependent 44 5 Unwind the mains cable 5 fully and plug it into an earthed socket 6 Set the main power button 9 to the on position illuminated in red 7 The temperature and steam level automatic selection function will be selected by default This allows you to start ironing wi
3. 13 14 Ar AN o Vertical steam SA This can be used to remove creases from hanging clothes curtains etc It cannot be used on a synthetic setting for delicate items Warning Never direct the steam jet at garments that are being worn Never aim the steam at people or animals 1 Set the temperature to the setting 2 Hold the iron in an upright position 15 cm away from the garment being steamed 3 You can steam iron curtains and hanging garments jackets suits coats by placing the iron in a vertical position and pressing the steam release button 13 or 14 Energy saving Energy Saving Water Saving eco button If the Energy saving button 7 is switched on you can save up to 25 of the energy and 40 of the water consumption and still achieve good results when ironing most of your garments It is advisable to use the normal energy setting only for thick and very wrinkled fabrics In comparison to the maximum setting Note If you work with the Energy saving function the variable steam regulation and temperature regulation can still be used as recommended 49 secure auto shut off model dependent If during ironing the steam release button 13 14 on the iron handle is not pressed for a certain length of time 8 minutes the steam station will automatically switch off The secure icon will flash when auto shut off has been ac
4. Register your new Bosch now http www bosch home co uk Sensixx B45L BOSCH en Operating instructions General safety instructions Description i Temp function AntiShine function How to use the steam station Preparations before ironing Setting the temperature Ironing with steam PulseSteam function oo Oa F ON gt Ironing without steam A e Vertical steam Energy saving eco button N secure auto shut off wo Fabric protection soleplate cover X gt Descaling the filter and the boiler S Cc Rinsing the iron steam chamber O Cleaning amp Maintenance X N Storing the appliance oo Advice on disposal oO Guarantee conditions N e Trouble shooting gt gt Thank you for buying the Sensixx B45L steam station the new steam ironing system from Bosch Please visit www bosch home co uk for more product information or to register your product just follow the link to the Online guarantee registration Introduction These instructions for use contain valuable information about the unique features of this system and some hints to make ironing easier for you We hope that you enjoy ironing with this steam station General safety instructions Important Carefully read through the operating instructions for the appliance and keep them safe for future reference Open out the first page of the booklet to help yo
5. age it If the clean icon flashes three beeps may be heard at the same time this indicates that the boiler must be rinsed Please proceed as follows Model dependent gt gt 1 Check carefully that the appliance is cold and unplugged for more than 2 hours and that the water tank 1 is empty 2 Fix the iron to the base by inserting the tip of the iron into the front slot and moving the SecureLock lever 10 against the heel of the iron 3 Place your appliance over a sink or bucket 4 Lean the appliance on the opposite side of the filter opening 5 Unscrew the filter 12 and take it out 6 To wash the filter you may a Place the filter under the water tap and wash it until calc residues are removed Squeeze the filter as indicated in the picture 6 b Immerse the filter in tap water 250 ml mixed with a measure 25 ml of descaling fluid Rinse filter thoroughly before placing it back into the boiler The descaling fluid can be obtained from our After sales service or from our website Accessory code Nace After sales Online shop 311144 TDZ1101 7 Holding your steam generator in the lateral position and using a jug fill the boiler with 1 4 litre of water and replace the filter 8 Shake the base unit for a few moments unscrew the filter again and empty the boiler completely over a sink or bucket For best results we recommend tha
6. ap water in your district is very hard mix tap water with distilled water 1 2 Clean the soleplate with a damp cloth Never add products to the water The boiler is not switched on Set the main power button 9 to the I position illuminated in red and or fill the water tank Increase the steam flow see section Ironing with steam BOSCH Problem Possible causes Solution The ironed garment turns dark and or sticks to the soleplate The soleplate turns brown The appliance makes a pumping sound Loss of pressure during ironing Water spots appear on the garment during ironing Water spots appear on the garment during use of the PulseSteam function The hose gets hot during use Water leakage from the boiler The iron does not stop steaming after placing it on the pad 2 The selected temperature is too high and has damaged the garment This is a regular consequence of continued use over a long period of time Water is being pumped into the steam tank Water tank 1 is not correctly inserted in the housing The sound will not stop Steam release button has been activated for too long a period of time that is it has been pressed too frequently May be caused by steam condensed on the ironing board Water spots are caused by steam condensation in the hose when cooling down after use This is normal It is caused by the steam passi
7. ent use the soleplate may be soiled Water flows The steam function is being through the used before it has reached holes on the the correct temperature soleplate The water is condensing inside the pipes because steam is being used for the first time or has not been used for a long time The steam generator contains too much scale Dirt comes out through the soleplate There is a build up of scale or minerals in the steam tank Chemical products or additives have been used The iron does not produce any steam or the water tank is empty The steam regulation is set to the minimum position Model dependent Check the mains cable 5 the plug and the socket Set the main power button 9 to the I position illuminated in red Set the main power button 9 to the I position illuminated in red Set the temperature to the desired position This is completely normal and will stop after a short while Clean the soleplate according to the cleaning instructions in this manual Reduce the steam flow when ironing at low temperatures Point the iron away from the ironing area and press the steam release button until team is produced Clean the boiler as described in section Descaling the filter and the boiler Use tap water mixed 5096 with distilled or demineralised water To prolong the optimum steam function mix tap water with distilled water 1 1 If the t
8. er can ask the public power supply company for the system impedance at the interface point The appliance must never be placed directly under the tap to fill the water tank Unplug the appliance from the mains supply after each use or if a fault is suspected The electrical plug must not be removed from the socket by pulling the cable Never immerse the iron in water or any other fluid Do not leave the appliance exposed to weather conditions rain sun frost etc Important This appliance reaches high temperatures and produces steam during use this could cause scalds or burns in case of improper use The steam hose base station metal plate at the bottom of the removable iron pad 2 and in particular the iron can get hot when used This is normal Never aim the steam at people or animals Do not allow the power cable to come into contact with the soleplate when it is hot BOSCH Mm 1 Removable water tank 10 Iron SecureLock system 2 Removable iron pad 11 Housing with internal steam 3 Carrying handle generator 4 Steam hose and mains cable 12 Descaling filter storage compartment 13 Steam release button 5 Mains cable 14 Steam release button Ultimate 6 Steam hose 15 Iron pilot light 7 Energy Saving button green 16 Soleplate 8 Display 17 Fabric protection soleplate cover 9 Illuminated main power button red Model dependent Model dependent 44 i Tem p function
9. he guarantee Do not use condensation water from tumble dryers air conditioning systems or similar This appliance has been designed to use normal tap water The iron is not designed to rest on its heel Please always position it horizontally on the iron pad 2 The iron pad can be placed into the specially designed recess on the appliance or somewhere suitable alongside the ironing area Never rest the iron on the appliance without the iron pad During its first use the iron may produce certain vapours and odours along with white particles on the soleplate this is normal and will stop after a few minutes While the steam release button is pressed the water tank may produce a pumping sound this is normal indicating that water is being pumped to the steam tank Setting the temperature By default the steam station automatically chooses the i Temp temperature setting If necessary the temperature setting may be modified and adapted to your needs zu Temp eue antiShine 1 Check the ironing instruction label on the garment to determine the correct ironing temperature 2 Select the required ironing temperature setting Temperature icon on Suitable for display Aldi Any type of fabric which iTemp can be ironed Temperature setting for dark and delicate fabrics antiShine Reduces the risk of shiny marks l Synthetics Silk Wool cmd Cotton Linen 3 The selected te
10. he iron on the iron pad 2 standing on the soleplate and fix it by inserting the tip of the iron into the front slot and moving the SecureLock lever 10 against the heel of the iron 5 Store the mains cable 5 and steam hose 6 in the storage compartment 4 Do not wrap the cords too tight 6 Use the iron s handle when moving the appliance as shown in figure below or use the carrying handles 3 on either side gt gt BOSCH 18 Advice on disposal 1 Guarantee conditions Our goods come in optimised The terms of the guarantee for this packaging This basically consists of appliance are in accordance with that non contaminating materials which stated by our representative for the should be handed over to the local country in which it is sold waste disposal service as secondary The details of these conditions can be raw materials Your local town council obtained from the retailer from whom can give you information about how to the appliance was purchased The dispose of obsolete appliances purchase receipt must be presented This appliance is labelled in when making any claims against the accordance with European terms of this guarantee Directive 2012 19 EU concerning used electrical and electronic appliances waste electrical and electronic equipment WEEE The guideline determines the framework for the return and recycling of used appliances as applicable throughout the EU 2U Trouble shooti
11. mperature icon will flash while the soleplate 16 is heating and will stop flashing as soon as the soleplate has reached the selected temperature Tips Sort your garments out based on their cleaning symbol labels always starting with clothes that have to be ironed at the lowest temperatures BOSCH 44 If you are not sure what the garment is made of then begin ironing at a low temperature and decide on the correct temperature by ironing a small section not usually seen when worn Ironing with UN steam vs The steam control is used to adjust the amount of steam produced when ironing By default the steam station automatically chooses the i Temp steam setting The steam setting can be changed by the user by changing the temperature The steam station will propose the suitable steam level automatically depending on the temperature selection made on display u W CE Bu If necessary the steam level can be adapted to your needs by touching the Dy amp icon on the display 8 The selected icon flashes until the pressure corresponding to each steam level is reached Steam is now ready to be released by pressing the steam release buttons 13 or 14 Model dependent Attention When ironing on a lower temperature setting only press the steam release button 13 for a few seconds at a time If you find that water is dripping out of the soleplate set the temperat
12. ng Problem Possible causes Solution The display Dirt on the display Clean the display with a damp does not react Fingers are too cold cotton cloth not too wet when touched Warm your fingers a little bit and try again secure icon The steam release button 13 Press the steam release button flashes on the iron handle has not again to switch the steam been pressed during the last 8 station back on minutes and the auto shut off System has been activated r Water tank is empty Fill the water tank ESI icon flashes clean icon Boiler and filter must be Rinse the filter and the boiler flashes rinsed according to the cleaning instructions in this manual see section Descaling the filter and the boiler When touching The beep has been Activate it according to the the display the deactivated instructions in this manual beep cannot see section Beep activation be heard deactivation Model dependent BOSCH 44 Problem Possible causes Solution O The steam There is a connection generator does problem not come on The main power button is not switched on The iron does The main power button is not heat up not switched on The temperature is set to a low position The iron During first use certain begins to components on the smoke when appliance have been lightly Switched on greased at the factory and may produce a little smoke when initially heated During subsequ
13. ng through the hose during steam ironing Filter 12 located at the side of the appliance is loose PulseSteam function has been activated by double click Select a suitable temperature for the material being ironed and clean the soleplate with a damp cloth Clean the soleplate with a damp cloth This is normal Adjust the water tank to fit correctly If the sound will not stop do not use the steam generator and contact an authorised technical service centre Use the steam release button at intervals This improves the ironing result as the textiles will be steamed dried and ironed properly Wipe the textile cover of the ironing board and iron any water drops to dry them Water drops stop coming out of the soleplate after using the PulseSteam function for some time Place the hose on the opposite side so that you cannot touch the hose during ironing Tighten up the filter Just press the trigger once again and the iron will stop steaming at once If the above does not solve the problem get in touch with an authorised technical service You can download this manual from the local homepages of Bosch BOSCH Model dependent gt gt Customer Service Great Britain Bosch Customer Service Grand Union House UK 44 0 844 892 8979 Old Wolverton Road Milton Keynes IRL 353 0 1450 2655 MK12 5PT www bosch home co uk 002 B45L LCD i Temp AntiShine GB 02 14
14. t this operation is performed twice Important before re closing make sure no water remains in the boiler 9 Replace and tighten the filter To reset the clean counter switch the station on and off twice keeping it off for at least 30 seconds each time on 30s off on 30s off on BOSCH ac Rinsing the iron steam chamber IN Caution Risk of burns This procedure helps to remove scale particles from the steam chamber This cleaning procedure may be performed occasionally approximately once a year when after a long period of use with very hard water scale particles start to come out of the soleplate a Ensure that the iron has cooled down b Fill the tank with tap water c Plug in the mains cable and set the main power button 9 to the position illuminated in red d Set the temperature to the setting e Set the steam setting to t and wait until the icon stops flashing f Hold the iron over the sink or a container to collect the water g Press the steam release button 13 and gently shake the iron Boiling water and steam will be released carrying scale and or deposits that might be inside This process may take from 5 up to 10 minutes Please note that if you have filled the water tank to the maximum you do not have to continue until it is completely empty but just long enough so that there are no more scale deposits appearing from your iron hand set h Set
15. the temperature to the setting without pressing the steam release buttons 13 14 The water in the steam chamber will start evaporating Wait until all the water inside the chamber has been evaporated i To clean the soleplate immediately rub off any residue by running the hot iron over a dry cotton cloth EB 5oscH 44 Model dependent a Cleaning amp A 47 Storing the Maintenance appliance IN Attention Risk of burns Always unplug the appliance from the mains supply before carrying out any cleaning or maintenance operation on it 1 After ironing disconnect the plug and allow the appliance to cool down before cleaning 2 Wipe the housing handle and iron body with a damp cotton cloth 3 If the soleplate is soiled with dirt or scale clean it with a damp cotton cloth 4 If the cloth is synthetic it may melt due to the high temperature on the soleplate 16 Switch off the steam and rub off any residue immediately with a thickly folded dry cotton cloth 5 Never use abrasive products or solvents To keep the soleplate 16 smooth you should avoid hard contact with metal objects Never use a scouring pad or chemicals to clean the soleplate Model dependent 1 Always allow the appliance to cool down before storing it 2 Set the main power button to the 0 position the red light will go off and disconnect the mains cable 3 Empty the water tank 4 Place t
16. thout having to select the steam or temperature levels If required you can select your preferred setting manually by using the touch icons on the display 8 The selected temperature and steam icons will stop flashing after a time indicating that the appliance is ready to use Remark The steam generator will take more time to generate steam only on initial heating up or after performing the de scaling operation Calc n Clean When water is already present in the steam generator during regular use heat up time to reach the operating temperature will be faster 8 This appliance has a built in water level sensor which indicates when the water tank 1 must be filled r The 2 icon will flash when the water tank is empty three beeps may be heard at the same time Model dependent Important Normal tap water can be used To prolong the optimum steam function you can mix tap water with distilled water 1 1 If the tap water in your district is very hard mix tap water with distilled water 1 2 You can inquire about the water hardness with your local water supplier The water tank 1 can be refilled at any time while using the appliance To avoid damage and or contamination of the water tank and the boiler do not put perfume vinegar starch descaling agents additives or any other type of chemical product into the water tank Any damage caused by the use of the aforementioned products will void t
17. tivated three beeps may be heard at the same time To switch the steam station back on press the steam release button again BOSCH 43 Fabric protection 2 soleplate cover protect model dependent The fabric protection soleplate cover 17 is used for steam ironing delicate garments at maximum temperature without damaging them Use of the soleplate cover also does away with the need for a cloth to prevent shine on dark materials It is advisable to first iron a small section on the inside of the garment to see if it is suitable To attach the soleplate cover to the iron place the tip of the iron into the end of the soleplate cover and pull the elastic strap over the lower rear of the iron until it fits tightly To release the soleplate cover pull the elastic strap and remove the iron The fabric protection soleplate cover may be purchased from customer service or from our website Name of Accessory code accesso After sales ry Online shop 571510 TDZ2045 Descaling the filter and the boiler Cale n Clean Advanced Calc n Clean Advanced To extend the life of your steam generator and to avoid any build up of scale it is essential that you rinse out the filter 12 and the boiler after a period of use approximately after 50 hours If the water is hard increase the frequency Model dependent 44 Do not use descaling agents for rinsing out the boiler as they could dam
18. u to understand how the appliance works This appliance complies with international safety standards This appliance has been designed exclusively for domestic use and must not be used for industrial purposes This appliance must only be used for the purposes for which it was designed i e as an iron Any other use will be considered improper and consequently dangerous The manufacturer will not be held responsible for any damage arising from misuse or improper use The iron must not be left unattended while it is connected to the supply mains Remove the plug from the socket before filling the appliance with water or before pouring out the remaining water after use The appliance must be used and placed on a stable surface When placed on its stand make sure that the surface on which the stand is placed is stable The iron should not be used if it has been dropped if there are visible signs of damage or if it is leaking water It must be checked by an authorized Technical Service Centre before it can be used again With the aim of avoiding dangerous situations any work or repair that the appliance may need e g replacing a faulty mains cable must only be carried out by qualified personnel from an Authorised Technical Service Centre This appliance can be used by children aged from 8 years and above and persons with reduced physical sensory or mental capabilities or lack of experience BOSCH and kno
19. ure to a higher position take care that the garment can be ironed on this heat temperature setting At the beginning of each use it is possible that drops of water will be dispensed alongside steam Therefore it is advisable to try the iron on the ironing board or a piece of cloth to start with Tip For better ironing results iron the last strokes without steam to dry the garment ZA PulseSteam function This appliance has a special function for tackling difficult creases The PulseSteam function helps soften stubborn garments like jeans or linen faster When the steam release button is activated the steam generator will release three powerful shots of steam so that the steam reaches even deeper into the fabric 1 Set the temperature to the setting 2 Press the steam release button 14 on the top of the handle or model dependent Quickly press the steam release button 13 on the bottom of the handle twice double click Remarks It is possible to stop the shots of steam by quickly pressing the steam button again Some water drops may appear when you use the PulseSteam function for the first time The water drops will disappear after you have used the function for some time Model dependent gt gt y IJ I Ironing without K steam This enables the iron to be used for dry ironing 1 Begin ironing but without pressing the steam release buttons
20. wledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved Children shall not play with the appliance Cleaning and user maintenance shall not be made by children without supervision Keep the iron and its cord out of reach of children less than 8 years of age when it is energized or cooling down CAUTION Hot surface Surface is liable to get hot during use This appliance is to be connected and used in accordance with the information stated on its characteristics plate This appliance must be connected to an earthed socket If it is absolutely necessary to use an extension cable make sure that it is suitable for 16A and has a socket with an earth connection Certain environmental conditions can cause instability in steam production and temperature in a short period of time If necessary the user can ask the public power supply company for the system impedance at the interface point If the safety fuse fitted in the appliance blows the appliance will be rendered inoperative To restore normal operation the appliance will have to be taken to an authorised Technical Service Centre In order to avoid that under unfavourable mains conditions phenomena like transient voltage drops or lighting fluctuations can happen it is recommended that the iron is connected to a power supply System with a maximum impedance of 0 47 Q If necessary the us
21. y type of fabric which can be ironed on this setting Temperature setting for dark and delicate fabrics Reduces the risk of shiny marks Indicates that the selected ironing temperature is suitable for silk and synthetic fabrics Indicates that the selected ironing temperature is suitable for wool Indicates that the selected ironing temperature is suitable for cotton and linen To change the temperature of the soleplate touch the J icon on the display 8 repeatedly The iron runs through the following cycle femen shine PIE a 4 Steam settings Steam level selection touch MI icon is used to change the I vo amount of steam coming out of the soleplate M UJ Low steam flow Medium steam flow 4993 High steam flow When i Temp and AntiShine functions are selected it is not possible to NC the steam setting by pressing the icon The steam amount is automatically selected Only on A A settings it is possible to change the steam amount To change the amount of steam manually touch the icon on the display 8 repeatedly The steam generator runs through the following cycle AN gt 29 eod The selected icon flashes until the pressure corresponding to each steam level is reached Steam is now ready to be released by pressing the steam release buttons 13 or 14 5 Other indicators Indicates flashing that the Talr auto shut off system has
Download Pdf Manuals
Related Search