USER MANUAL - Kramer Electronics Japan Homepage
Contents
1. a Figure 4 TP 126 UXGA Audio Data Line Receiver Underside 1 Using a UTP cable with CAT 5 connectors at both ends the PINOUT is defined in Figure 7 and Table 6 2 Degradation and UXGA signal loss can result from using long cables due to stray capacitance sometimes leading to a total loss of sharpness in high resolution signals 9 Connecting the TP 125 TP 126 Transmitter Receiver Pair Table 4 TP 126 UXGA Audio Data Line Receiver Underside Features Feature Function 1 VS Switch Slide down to set the V SYNC to negative polarity NEG slide up to set the V SYNC to positive polarity NORM 2 HS Switch Slide down to set the H SYNC to negative polarity NEG slide up to set the H SYNC to positive polarity NORM 5 Connecting the TP 125 TP 126 Transmitter Receiver Pair You can use the TP 125 UXGA Audio Data Line Transmitter and the TP 126 UXGA Audio Data Line Receiver to configure a twisted pair transmitter and receiver system to transmit the video audio and RS 232 control signals via CAT 5 UTP cable To connect the TP 125 and the TP 126 to create a twisted pair transmitter and receiver system as the example in Figure 5 illustrates do the following 1 On the TP 125 connect An UXGA source for example the graphics card on a laptop to the UXGA IN 15 pin HD F connector and an audio source to the Audio IN 3 5mm mini jack for example using a Kramer C GMA2. approx ACCESSORIES Power supply 13 LIMITED WARRANTY Kramer Electronics hereafter Kramer warrants this product free from defects in material and workmanship under the following terms HOW LONGIS THE WARRANTY Labor and parts are warranted for seven years from the date of the first customer purchase WHOIS PROTECTED Only the first purchase customer may enforce this warranty WHAT IS COVERED AND WHAT IS NOT COVERED Except as below this warranty covers all defects in material or workmanship in this product The following are not covered by the warranty 1 Any product which is not distributed by Kramer or which is not purchased from an authorized Kramer dealer If you are uncertain as to whether a dealer is authorized please contact Kramer at one of the agents listed in the Web site www kramerelectronics com 2 Any product on which the serial number has been defaced modified or removed or on which the WARRANTY VOID IF TAMPERED sticker has been torn reattached removed or otherwise interfered with 3 Damage deterioration or malfunction resulting from i Accident misuse abuse neglect fire water lightning or other acts of nature ii Product modification or failure to follow instructions supplied with the product iii Repair or attempted repair by anyone not authorized by Kramer iv Any shipment of the product claims must be presented to the carrier v Removalor installation ofthe product
3. vi Any other cause which does not relate to a product defect vii Cartons equipment enclosures cables or accessories used in conjunction with the product WHAT WE WILL PAY FOR AND WHAT WE WILL NOT PAY FOR We will pay labor and material expenses for covered items We will not pay for the following 1 Removal or installations charges 2 Costs of initial technical adjustments set up including adjustment of user controls or programming These costs are the responsibility of the Kramer dealer from whom the product was purchased 3 Shipping charges HOW YOU CAN GET WARRANTY SERVICE 1 To obtain service on you product you must take or ship it prepaid to any authorized Kramer service center 2 Whenever warranty service is required the original dated invoice or a copy must be presented as proof of warranty coverage and should be included in any shipment of the product Please also include in any mailing a contact name company address and a description of the problem s 3 For the name of the nearest Kramer authorized service center consult your authorized dealer LIMITATION OF IMPLIED WARRANTIES All implied warranties including warranties of merchantability and fitness for a particular purpose are limited in duration to the length of this warranty EXCLUSION OF DAMAGES The liability of Kramer for any effective products is limited to the repair or replacement of the product at our option Kramer shall not be liable for 1 D
4. may adversely influence signal quality and position your Kramer TP 125 TP 126 away from moisture excessive sunlight and dust 1 CAT 5 cable is still suitable for the video audio transmission but not for feeding the power at these distances 2 Available from Kramer Electronics on our Web site at http www kramerelectronics com KRAMER SIMPLE CREATIVE TECHNOLOGY Your TP 125 TP 126 4 1 No operator serviceable parts inside unit Use only the Kramer Electronics input power wall adapter that is provided with this unit EVwniiry Disconnect power and unplug unit from wall before installing or removing device or servicing unit Your TP 125 TP 126 This section defines the e TP 125 UXGA Audio Data Line Transmitter see section 4 1 e TP 126 UXGA Audio Data Line Receiver see section 4 2 Your TP 125 UXGA Audio Data Line Transmitter The TP 125 is a high performance transmitter that accepts e A computer graphics input signal e An unbalanced stereo analog audio signal e RS 232 control commands The TP 125 codes the signals and transmits them over CAT 5 cable to a TP 126 receiver The stereo analog audio signal is converted to the digital audio S PDIF stream before transmitting thus preserving the quality of the audio source signals Commands and data can flow in both directions via the RS 232 interface allowing status requests and control of the destination unit F
5. ANALOG Orr rA e 00000 E 00000 90000 7 i uxca OUT LINE IN AUDIO 12V a PEt Figure 3 TP 126 UXGA Audio Data Line Receiver Top Front and Rear KRAMER SIMPLE CREATIVE TECHNOLOGY Your TP 125 TP 126 Table 3 TP 126 UXGA Audio Data Line Receiver Top Front and Rear Features Feature Function 1 12V DC 12V DC connector for powering the unit 2 O S PDIF RCA connector Connects to the digital audio acceptor 3 3 ANALOG 3 5mm Mini Jack Connects to the analog audio acceptor 4 RS 232 Terminal Block Connector Connects to the controlled unit 5 LINE IN RJ 45 Connector Connects to the LINE OUT RJ 45 connector on the TP 125 6 UXGA OUT 15 pin HD F Connector Connects to the UXGA acceptor 7 ON LED Illuminates when receiving power 8 EQ Trimmer Adjusts the cable compensation equalization level 9 LEVEL Trimmer Adjusts the output signal level 10 LINK LED Iluminates when receiving the correct input signal 4 2 1 Your TP 126 UXGA Audio Data Line Receiver Underside Figure 4 and Table 4 define the underside of the TP 126 UXGA Audio Data Line Receiver Note that you need to open the TP 126 unit to gain access to the Vs and Hs Polarity switches After setting the switches close the TP 126 unit g m Vs Hs POLARITY UXGA Audio Data Line Receiver TP 126
6. Please use recommended interconnection cables to connect the machine to other components 14 For the latest information on our products and a list of Kramer distributors visit our Web site www kramerelectronics com where updates to this user manual may be found We welcome your questions comments and feedback Caution Safety Warning Disconnect the unit from the power supply before opening servicing Institute of Quality amp Control Kramer Electronics Ltd Web site www kramerelectronics com E mail info kramerel com P N 2900 000371 REV 3
7. GMA cable VGA 15 pin HD M Audio jack to VGA 15 pin HD M Audio jack An RS 232 cable with a 9 pin D sub connector at one end to the laptop and a 3 PIN terminal block connector at the other end to the TP 125 RS 232 port 2 On the TP 126 connect The UXGA OUT 15 pin HD F connector to the AV display system The S PDIF Audio OUT RCA connector to a digital AV Receiver leave the ANALOG Audio OUT 3 5mm mini jack unconnected An RS 232 cable with a 3 PIN terminal block connector at one end to the TP 126 RS 232 port and a 9 PIN D SUB connector at the other end to the RS 232 port on the AV display system 1 By default both switches are set down for a negative V SYNC and H SYNC polarity 2 Not supplied The full list of Kramer cables is on our Web site at http www kramerelectronics com Alternatively you can connect an UXGA source to the UXGA IN 15 pin HD F connector and a separate audio source to the AUDIO IN 3 5mm mini jack 3 As defined in Figure 6 and Table 5 10 KRAMER SIMPLE CREATIVE TECHNOLOGY Connecting the TP 125 TP 126 Transmitter Receiver Pair 3 Connect the Line OUT RJ 45 connector on the TP 125 to the LINE IN RJ 45 connector on the TP 126 via UTP cabling with a range of more than 300ft gt 100m 4 Connect the 12V DC power supply to the power socket and connect the adapter to the mains electricity on either or both the TP 125 or the TP 126 5 On the TP 126 Adjust the video out
8. Kramer Electronics Ltd USER MANUAL Models TP 125 UXGA Audio Data Line Transmitter TP 126 UXGA Audio Data Line Receiver Contents Contents 1 Introduction 2 Getting Started 2 1 Quick Start 3 Overview 3 1 About the Power Connect Feature 3 2 Shielded Twisted Pair STP Unshielded Twisted Pair UTP 3 3 Recommendations for Achieving the Best Performance 4 Your TP 125 TP 126 4 1 Your TP 125 UXGA Audio Data Line Transmitter 4 1 1 The TP 125 Internal Polarity Switches 4 2 Your TP 126 UXGA Audio Data Line Receiver 4 2 1 Your TP 126 UXGA Audio Data Line Receiver Underside 5 Connecting the UXGA Audio Data Line Transmitter Receiver 5 1 Transmitting via RS 232 for example using a PC 5 2 Wiring the CAT 5 RJ 45 Connectors 6 Technical Specifications Figures Figure 1 TP 125 UXGA Audio Data Line Transmitter Figure 2 TP 125 Internal Polarity Switches Figure 3 TP 126 UXGA Audio Data Line Receiver Top Front and Rear Figure 4 TP 126 UXGA Audio Data Line Receiver Underside Figure 5 Connecting the UXGA Audio Data Line Transmitter Receiver System Figure 6 RS 232 PINOUT Connection Figure 7 CAT 5 Connector Tables Table 1 Table 2 Table 3 Table 4 Table 5 Table 6 Table 7 TP 125 UXGA Audio Data Line Transmitter Features Features of the TP 125 Internal Polarity Switches TP 126 UXGA Audio Data Line Receiver Top Front and Rear Feature
9. Polarity Switches Feature Function VS Switch Slide down to set the V SYNC to negative polarity NEG slide up to set the V SYNC to positive polarity NORM HS Switch Slide down to set the H SYNC to negative polarity NEG slide up to set the H SYNC to positive polarity NORM Your TP 126 UXGA Audio Data Line Receiver The TP 126 is a high performance receiver obtaining the computer graphics signal audio control data from the Kramer TP 125 via UTP cabling at its CAT 5 line input The TP 126 outputs a computer graphics signal an unbalanced stereo analog audio signal a converted digital audio S PDIF signal and bi directional RS 232 control commands and data to and from the receiver The RS 232 interface makes it possible to control virtually any device over a transmission range of more than 300 feet more than 100 meters over UTP cabling 1 By default both switches are set down for a negative V SYNC and H SYNC polarity Your TP 125 TP 126 In addition the TP 126 features e Level and EQ control for the UXGA signals e The capability to change the polarity of decoding H and V Sync e 24 bit 48kHz S PDIF digital audio that supplies the highest quality audio e 12V DC power Figure 3 and Table 3 define the TP 126 UXGA Audio Data Line Receiver KRAMER TOOLS UXGA Audio Data Line Receiver TP 126 O00 EQ a oy
10. amage to other property caused by defects in this product damages based upon inconvenience loss of use of the product loss of time commercial loss or 2 Any other damages whether incidental consequential or otherwise Some countries may not allow limitations on how long an implied warranty lasts and or do not allow the exclusion or limitation of incidental or consequential damages so the above limitations and exclusions may not apply to you This warranty gives you specific legal rights and you may also have other rights which vary from place to place NOTE All products returned to Kramer for service must have prior approval This may be obtained from your dealer This equipment has been tested to determine compliance with the requirements of EN 50081 Electromagnetic compatibility EMC generic emission standard Part 1 Residential commercial and light industry EN 50082 Electromagnetic compatibility EMC generic immunity standard Part 1 Residential commercial and light industry environment CFR 47 FCC Rules and Regulations Part 15 Radio frequency devices Subpart B Unintentional radiators CAUTION amp Servicing the machines can only be done by an authorized Kramer technician Any user who makes changes or modifications to the unit without the expressed approval of the manufacturer will void user authority to operate the equipment amp Use the supplied DC power supply to feed power to the machine amp
11. hers and Matrix Switchers GROUP 3 Control Systems GROUP 4 Format Standards Converters GROUP 5 Twisted Pair Solutions GROUP 6 Specialty AV Products GROUP 7 Scan Converters and Scalers GROUP 8 Cables and Connectors GROUP 9 Room Connectivity GROUP 10 Accessories and Rack Adapters GROUP 11 Sierra Products 2 Download up to date Kramer user manuals from our Web site at http www kramerelectronics com 3 The complete list of Kramer cables is on our Web site at http www kramerelectronics com 1 Getting Started 2 1 Quick Start This quick start chart summarizes the basic setup and operation steps Step 1 Connect the inputs and outputs see section 5 Computer Graphics Audio RS 232 Control AV Display System with Built in Speakers and RS 232 Interface Step 2 Turn the power ON Attach a 12V DC power supply to the TP 125 and or TP 126 2 KRAMER SIMPLE CREATIVE TECHNOLOGY Overview Overview The TP 125 and TP 126 are a high performance twisted pair transmitter and receiver for computer graphics video including HDTV unbalanced stereo audio and RS 232 control commands The TP 125 converts computer graphics video unbalanced stereo analog audio and RS 232 control commands to a twisted pair signal and the TP 126 converts the twisted pair signal back into computer graphics video unbalanced stereo and S PDIF digital audio and RS 232 control signals Together the TP 125 and TP 126 form a com
12. igure I and Table I define the TP 125 1 For example model number AD2512C part number 2535 000251 Your TP 125 TP 126 KRAMER TOOLS UXGA Audio Data Line Transmitter TP 125 UXGA Audio Data Line Transmitter TP 125 3 fam THQ Ye RS 232 Aupio IN 12V DC Figure 1 TP 125 UXGA Audio Data Line Transmitter Table 1 TP 125 UXGA Audio Data Line Transmitter Features Feature Function 1 12V DC 12V DC connector for powering the unit 2 AUDIO IN 3 5mm Mini Jack Connects to the audio source 3 RS 232 Terminal Block Connector Connects to the PC or the Remote Controller see section 5 1 4 LINE OUT RJ 45 Connector Connects to the LINE IN RJ 45 connector on the TP 126 UXGA Audio Line Receiver 5 UXGA IN 15 pin HD F Connector Connect to the UXGA source 6 ON LED llluminates when receiving power KRAMER SIMPLE CREATIVE TECHNOLOGY Your TP 125 TP 126 The TP 125 Internal Polarity Switches Figure 2 and Table 2 define the internal sync polarity switches inside the TP 125 Note that you need to open the TP 125 unit to gain access to the Vs and Hs Polarity switches After setting the switches close the TP 125 unit KRAMER TOOLS V UXGA Audio Data Line Transmitter TP 125 i S POLARITY TEL sm 4 2 Figure 2 TP 125 Internal Polarity Switches Table 2 Features of the TP 125 Internal
13. isted pair STP cable or unshielded twisted pair UTP cable depends on the nature of the application In applications with high interference shielded twisted pair STP cable is recommended However the cable shield creates a capacitance that degrades the frequency response of the device For distances of 50 meters or less shielded twisted pair STP cable is preferred because it provides interference protection without any apparent degradation In applications where either 1 the source and transmitter or receiver and destination monitor are disconnected from common ground or 2 the source area building and destination area have no common ground STP cable is preferred For long range applications unshielded twisted pair UTP cable is preferred However unshielded twisted pair UTP cable should be installed far away from sources of electromagnetic interference such as electric cables and motors It is recommended to use shielded twisted pair STP skew free Kramer cable BC SXTP for transmitting VGA signals and shielded twisted pair STP non skew free Kramer BC STP cable for digital signals Recommendations for Achieving the Best Performance To achieve the best performance e Use only good quality connection cables to avoid interference deterioration in signal quality due to poor matching and elevated noise levels often associated with low quality cables e Avoid interference from neighboring electrical appliances that
14. n White 1 Orange White 2 Green 2 Orange 3 Orange White 3 Green White 4 Blue 4 Blue 5 Blue White 5 Blue White 6 Orange 6 Green 7 Brown White 7 Brown White 8 Brown 8 Brown Pair 1 4and5 Pair 1 4and5 Pair 2 3 and 6 Pair 2 1 and2 Pair 3 1 and2 Pair 3 3 and 6 Pair 4 7 and 8 Pair 4 7 and 8 12 45 78 36 Figure 7 CAT 5 Connector 12 KRAMER SIMPLE CREATIVE TECHNOLOGY Technical Specifications 6 Technical Specifications The TP 125 TP 126 technical specifications are shown in Table 7 Table 7 Technical Specifications of the TP 125 TP 126 TP 125 TP 126 INPUTS Video 1 UXGA on an HD15 connector 1 RJ 45 LINE IN connector Audio 1 audio ANALOG 3 5mm mini jack OUTPUTS 1 RJ 45 OUT connector Video 1 UXGA on an HD15 connector Audio 1 audio S PDIF RCA connector 1 audio ANALOG 3 5mm mini jack MAX OUTPUT LEVEL Video 1 6V Audio 2 3V CONTROLS RS 232 3 PIN Terminal Block RS 232 3 PIN Terminal Block Level 7 5dB to 4 4dB EQ 0dB to 33dBm 130m 50MHz RS 232 BAUD RATE Up to 19200kbps RS 232 MODE Full duplex BANDWIDTH Audio 20Hz 20kHz 0 5dB S N RATIO Audio lt 80dB TOTAL GAIN Audio Analog analog 0dB Analog SPDIF 12dBFS COUPLING AC TND N Audio lt 0 01 POWER SOURCE 12 VDC 60mA DIMENSIONS 12 1cm x 7 18cm x 2 42cm 4 76 x 2 83 x 0 95 W D H WEIGHT 0 3 kg 0 67 Ibs
15. put signal level and or cable compensation equalization level with a screwdriver if required If necessary set the H SYNC and V SYNC switches on the underside TP 125 Computer Graphics Audio RS 232 Control AV Display System with Built in Speakers Figure 5 Connecting the UXGA Audio Data Line Transmitter Receiver System 1 For details of how to wire a CAT 5LINE IN LINE OUT RJ 45 connector see section 5 2 2 See section 3 1 3 By default both switches are set down for negative V SYNC and H SYNC polarity 11 Connecting the TP 125 TP 126 Transmitter Receiver Pair 5 1 Transmitting via RS 232 for example using a PC Prepare an RS 232 cable with a 9 pin D sub connector at one end and a 3 PIN terminal block connector at the other end as defined in Table 5 and Figure 6 Table 5 RS 232 PINOUT Connection Connect this PIN on To this PIN on the the Terminal Block 9 pin D sub Connector Connector TxD PIN 2 RxD PIN 3 GND PIN 5 5 2 Wiring the CAT 5 RJ 45 Connectors RS 232 Pinout PIN 5 Connected to GND PIN 3 Connected to RxD PIN 2 Connected to TxD To PC DB9F Figure 6 RS 232 PINOUT Connection Table 6 and Figure 7 define the CAT 5 pinout using a straight pin to pin cable with RJ 45 connectors Table 6 CAT 5 Connector Pinout EIA TIA 568A EIA TIA 568B PIN Wire Color PIN Wire Color 1 Gree
16. puter graphics audio line transmitter receiver system More specifically the products feature e High bandwidth of 350MHz 3dB e Resolution up to UXGA e HDTV compatibility e Simultaneous unbalanced stereo and S PDIF 24 bit 48kHz audio outputs TP 126 e Level gain and EQ peaking controls TP 126 e System range up to 100m 300ft e Power Connect System Only one unit in a system the transmitter or the receiver needs to be connected to a power source when the devices are within 50m 150ft of each other This user manual describes the following Kramer TOOLS e TP 125 UXGA Audio Data Line Transmitter see section 4 1 e TP 126 UXGA Audio Data Line Receiver see section 4 2 This section describes e The power connect feature see section 3 1 e Using shielded twisted pair STP unshielded twisted pair UTP see section 3 2 e Recommendations for achieving the best performance see section 3 3 Overview 3 1 3 2 3 3 About the Power Connect Feature The Power Connect feature applies as long as the cable can carry power The distance does not exceed 50 meters on standard CAT 5 cable for longer distances heavy gauge cable should be used For a CAT 5 cable exceeding a distance of 50 meters separate power supplies should be connected to the transmitter and to the receiver simultaneously Shielded Twisted Pair STP Unshielded Twisted Pair UTP The decision whether to use shielded tw
17. s TP 126 UXGA Audio Data Line Receiver Underside Features RS 232 PINOUT Connection CAT 5 Connector Pinout Technical Specifications of the TP 125 TP 126 ONNU BRHRBwW Pw e jm NNS n w RP OMAN AD 12 12 10 12 12 13 Introduction 1 Introduction Welcome to Kramer Electronics Since 1981 Kramer Electronics has been providing a world of unique creative and affordable solutions to the vast range of problems that confront the video audio presentation and broadcasting professional on a daily basis In recent years we have redesigned and upgraded most of our line making the best even better Our 1 000 plus different models now appear in 11 groups that are clearly defined by function Thank you for purchasing the Kramer TOOLS TP 125 UXGA Audio Data Line Transmitter and or TP 126 UXGA Audio Data Line Receiver which are ideal for e Presentation and multimedia applications e Long range graphics distribution for schools hospitals security and stores Each package includes the following items e TP 125 or TP 126 e Power adapter 12V DC Input e This user manual 2 Getting Started We recommend that you e Unpack the equipment carefully and save the original box and packaging materials for possible future shipment e Review the contents of this user manual e Use Kramer high performance high resolution cables 1 GROUP 1 Distribution Amplifiers GROUP 2 Switc
Download Pdf Manuals
Related Search