Rhino 2500FMP - Two Crossbar System - Rhino-Rack
Contents
1. CONTROLLED RHINO RACK Rhino 2500FMP Two Crossbar System Important Please refer to your fitting instruction to ensure that the roof racks are installed in the correct locations Check the contents of kit before commencing fitment and report any discrepancies Place these instructions in the vehicle s glove box after installation is complete Maximum carrying capacity 75kg 165lbs evenly distributed over crossbars Please refer to your vehicle manufacturers handbook and DK Specification sheet for maximum roof loading Always use the lower of the two figures Recommendations It is essential that all bolt connections be checked after driving a short distance when you first install your crossbars Bolt connections should be checked again at regular intervals probably once a week is enough depending on road conditions usage loads and distances travelled You should also check the crossbars each time they are refitted Make sure to fasten your load securely Please ensure that all loads are evenly distributed and that the centre of gravity is kept as low as possible Use only non stretch fastening ropes or straps Load Ratings When these roof racks are to be used on a vehicle that is driven off sealed roads the manufacturer maximum roof load rating to be found in the vehicles User Manual should be halved For example if the vehicles maximum roof load rating is 70kgs subtract 5kg weight of crossbar and legs these r2. acks when fitted to this vehicle should have no more than 35kgs loaded Caution The handling characteristics of the vehicle changes when you transport a load on the roof For safety reasons we recommend you exercise extreme care when transporting wind resistant loads Special consideration must be taken into account when cornering and braking Please remove crossbars when putting vehicle through an automatic car wash Note for Dealers and Fitters It is your responsibility to ensure instructions are given to the end user or client Rhino Rack 3 Pike Street Rydalmere Document No R083 NSW 2116 Australia Prepared By Kayle Everett Issue No 05 Ph 02 9638 4744 Authorised By Chris Murty Issue Date 4 03 2014 Fax 02 9638 4822 These instructions remain the property of Rhino Rack Australia Pty Ltd and may not be used or changed for any other purpose than intended Page 1 of 7 Rhino 2500FMP Two Crossbar System When these roof racks are to be used on a vehicle that is driven off sealed roads the manufacturer SS 70kg load rating _ 35 kg load rating maximum roof load rating to be Urban road Off road 70kg 2 found in the vehicles User Manual should be halved Do not forget to subtract 5kg from your maximum carrying capacity due to the weight of the crossbars and legs WARNING Important Load Carrying Instructions With u
3. specification sheet 4 Clip foot plate onto base of the leg with the arrow facing In or Out according to your vehicle listed in the DK spec sheet Y nannan enen example only Page 4 of 7 Rhino 2500FMP Two Crossbar System 1070mm 42 118 Push strip up against end of cut out Locate nut into Length of measurement strip is crossbar very important to ensure proper fitment of racks Page 5 of 7 Rhino 2500FMP Two Crossbar System Attach location decals Item 1 _ m Page 6 of 7 Rhino 2500FMP Two Crossbar System Locate M6 screw into stud Tighten plastic bolt housing alternately both sides Tighten 3 4 Nm 26 35 Ibf in Ensure rubber gasket flares evenly and no edges are tucked under 5 i fe f J j w A BT SD A m aot lt p a LS eI mea EN J o Der T Y Front cover Check Racks are secure Note SX100 pictured Page 7 of 7
4. tility vehicles the cabin and the canopy move independently Roofracks and vehicle can be damaged if the item transported is rigidly fixed at points on both the cabin and canopy Instead rigidly fix to either the cabin roofracks or the canopy roofracks Page 2 of 7 Rhino 2500FMP Two Crossbar System Item Component Name P Attachment stud kit specific CA1026 Ce ea Ce reram sa o eme o ree a Tools required Security Allen key provided Hex spanner provided Tape measure Torque wrench Scissors Refer to DK specification sheet for correct roof rack placement on your vehicle Discard parts shown below from RLKVA Page 3 of 7 Rhino 2500FMP Two Crossbar System 1 Remove M8 bolt and M8 nut 2 Attach hardware Item 2 Item 5 Item 9 Item 10 Item 3 Item 7 tem 3 Central locator lug Rear Rear Mea Right Left st i Pad R per Pad Clamp Clamp M365 M365 114490 114490 Arrow FORWARD W Nuwses M365 pction example only Clip rubber pad onto foot plate Pad central locator lug and end tabs must fully locate into the foot plate Note Certain rubber pad sets have a DK supplement sheet to show correct orientation Central locator lug pushes through End tabs clip in ESI Insert crossbar rubber DK
Download Pdf Manuals
Related Search