Dishwasher GSN 9476 A
Contents
1. You may select and operate a new programme following the programme cancellation process There might be residues of detergent or rinse aid left in the machine and or on the pieces being washed depending on the step the previous programme was in at the time of such cancellation Changing a Programme If you want to change running programme first of all press Start Pause Cancel button 2 to switch your machine into pause mode Second switch to the desired programme by pressing Programme Selection button 4 Third Start the new programme by pressing Start Pause Cancel button 2 again Your new selection will resume operation from the step in the previous programme For example if the previous programme was in rinsing step the new one will also start from the rinsing step If you want to run the newly selected programme from the beginning you have to apply the programme cancellation process first and then select a new programme Programming the Delayed Start You can delay the start of the selected programme until 24 hours Delayed start can not be set after the programme starts The selected programme must not be started in order to be able to set the delay time Delayed start indicator sand glass 13 will start flashing when the Time Delay Button 8 is pressed You can set the desired time by pressing the Time Delay Button 8 Press the Start Pause Cancel button 2 after setting the time The dela2. e These detergents will not give you the same drying performance that you can obtain by using separate detergent salt and rinse aid To increase the drying performance e Put your appliance s rinse aid setting at 1 and apply rinse aid When the rinse aid is used up add more rinse aid to the rinse aid dispenser e f you use combined detergents with a rinse aid setting higher than 1 hand contact may leave rainbow coloured water stains on the washed items and inside the machine e f you use combined detergents without adding salt lime scale may form especially on glasses To avoid lime scale formation e Put your appliance s water softener setting at 1 and add salt When the salt is used up add more salt to the water softener Using two in one detergent detergent and softening salt e These detergents do not contain rinse aid so you need to use the rinse aid setting as described in the manual making sure that there is rinse aid in the rinse aid dispenser with every wash and that you refill the rinse aid dispenser with rinse aid every time it is empty 14 GB Using two in one detergent and rinse aid e These detergents will not give you the same drying performance that you can obtain by using separate detergent salt and rinse aid To increase the drying performance e Put your appliance s rinse aid setting at 1 and apply rinse aid When the rinse aid is used up add more rinse aid to t
3. Cancel button 2 Set the desired time by pressing the Time Delay Button 8 Start the countdown for the new time by pressing the Start Pause Cancel button 2 again Usage of Child Lock Press the Child Lock buttons 4 and 5 simultaneously for three seconds in order to activate the child lock Child lock indicator 19 will appear on the screen Repeat the same procedure to disable the child lock Child lock does not lock the door of the machine but it prevents the selected programme or functions from being changed and disables the Start Pause Cancel button 2 Salt Indicator Please check the salt indicator 18 on the display to see whether there is enough softening salt in your machine or not You need to refill the powder dispenser whenever the salt warning indicator light lights WARNING If the water hardness level is stored as r1 salt indicator will never come on even if the salt container is empty Adjusting the water hardness level is explained in Water Softening System section Rinse Aid Indicator Check the rinse aid warning display 14 on the screen to find out if there is sufficient amount of rinse aid in your machine You must refill the rinse aid container when the rinse aid indicator comes on WARNING If the Rinse Aid Indicator is set to OFF rinse aid indicator will never come on even if the rinse aid container is empty Rinse Aid Indicator Setting e When your machine is
4. 13 Delayed Start Indicator 14 Rinse Aid Indicator 15 Half Load 1 2 Indicator 16 Rapid Indicator 17 Combi Tablet Indicator 18 Salt Indicator 19 Child Lock Indicator 20 Progress indicators a Wash 9 b Rinse lt 3 c Dry ee d End gt S 92S eo NS Button and Button Descriptions On Off Button 1 When you press the On Off button the display switches on with the last programme used and it dims when you turn the machine off If the Half Load 5 Rapid 6 Child Lock 19 and Combi Tablet 7 functions are enabled during the last programme used these functions will remain active when the machine is turned off and on again If you would like to disable these functions after turning the machine off and on again you must press the relevant buttons Start Pause Cancel Button 2 It is used to start pause or cancel the selected programme or the delayed start countdown The selected programme will start running when the Start Pause Cancel button 2 is pressed When the button is pressed 12 lights up Wait for two seconds to view the full display on the screen after you turn on the machine by pressing the On Off button 1 before you press Start Pause Cancel 2 button Programme Selection Button 4 You can select the washing programme you want to use with the aid of the Programme Data and Table of Average Consumption Values after pressing the programme
5. from the floor level and must not be extended otherwise the machine may not empty the waste water N E Es i X z x i l 3 I 3 3 W N Z ik ae wa 9 GB Installation of dishwasher Remove all packaging before positioning the machine See the following diagram Ensure there is a clearance each side of the machine to allow slight side ways movement for servicing Note If there is already enough space you don t need to remove the worktop to install it under the counter D Position the machine next to a water tap and a drain When inserting the machine ensure that the water inlet and drain hoses are not linked or squashed Care must be taken to ensure that the appliance does not stand on the electrical supply cable Good levelling is essential for correct closure and sealing of the door 10 GB is perfectly level using the adjustable feet When the appliance is correctly levelled the door will not catch on the inner liner on either side of the cabinet Ifthe door does not close correctly loosen or tighten the adjustable feet until the machine is perfectly level g How to use Water hardness amp regeneration settings The dishwasher requires lime free water Hard water leaves watermarks on your dishes Your dishwasher has a special water softening system to remove the hardness of the tap w
6. with chlorine 13 GB Warning Two in one and three in one detergents You will obtain the best results from your dishwasher if you use separate detergent rinse aid and water softening salt Detergent manufacturers also produce combined detergents known as two in one and three in one Three in one These products contain detergent rinse aid and water softening salt Two in one These products contain detergent and either rinse aid or water softening salt In general you will obtain satisfactory results from combined detergents only under specific usage conditions These detergents contain predetermined amounts of rinse aid and or softening salt This means that you cannot adjust the amount of water softening salt and rinse aid required to suit the water hardness level in your home You should bear the following points in mind when using such detergents e Be sure to check the specifications of the product you are using and whether it is a combined product or not e Follow the instructions on the packet when using these products e The use of these products at the correct appliance settings will ensure economical use of salt and or rinse aid e lfthe detergent is in tablet form never place these in the internal section or cutlery basket of the dishwasher Always place the tablets in the detergent dispenser of the detergent holder Using three in one detergent softening salt and rinse aid
7. with softening salt remove the lower rack first and unscrew the cap of the water softener turning anti clockwise Using the funnel provided will make filling easier After you fill the container screw cap tightly back into place turning clockwise until you hear a click sound Funnel Detergent use Any brand of powder gel and tablet detergents that have been designed for household dishwashers may be used Keep detergents in a cool and dry place and out of the reach of children Detergent must be added to the container before each use Detergent overdose may cause scratches on your dishes and there may be traces of detergent left in your machine Three types of detergent are available e Phosphate and containing chlorine e Phosphate containing no chlorine e Neither containing phosphate nor chlorine New compact powders are generally phosphate free As phosphates have water softening properties we suggest you add salt to the salt container even if the hardness of your water is as low as a 6 clarke degrees In hard water areas if a phosphate free detergent is used white marks on the dishes and glasses may be observed It may be prevented by increasing the amount of detergent Detergents without chlorine have less bleaching effect Coloured stains may not be completely removed This may be prevented by increasing the amount of detergent using a programme with a higher wash temperature or using a detergent
8. Dishwasher GSN 9476A Instruction Manual Blomberg Welcome Dear customer Congratulations on your choice of a quality dishwasher which has been designed to give you lasting service Please read these instructions before installing the dishwasher and using it for the first time The information contained herein is provided to avoid accidental risks and or damage to your appliance Make sure you understand the controls prior to using your appliance The dishwasher must only be used for it s intended purpose i e the washing of dishes in the home Failure to observe these instructions may invalidate your right to free service during the guarantee period Please keep these instructions in a safe place for your future reference If you have any questions or if you are not sure about any information contained in this booklet please contact us details are on the back cover Customer Service Notes Due to the quality control processes during production there may be some water left in your machine This does not cause any damage Preparation before use It is recommended that the dishwasher is operated on the Eco programme with prewash before loading with dishes TABLE OF CONTENTS 1 Know your dishwasher 6 Programme Selection and specification 3 Operating Your Machine 21 Button and Button Descriptions 22 2 Warning and safety Turbo fan heat drying system 23 information 5 Progr
9. amme Selection 23 Electrical Safety 5 Adding Functions to the Programme 23 Children s Safety 5 Programme Steps Follow up 24 General 5 Cancelling a Programme 24 Recycling 6 Changing a Programme 24 Energy and water saving e Programming the Delayed Start 24 What should not be washed in your Usage of Child Lock 25 dishwasher e Salt Indicator 25 Rinse Aid Indicator 25 3 Before first use 7 Rinse Aid Indicator Setting 25 Electrical requirements 7 Starting Your Machine 26 4 Installation 7 7 How to clean your Warning 8 dishwasher 28 This appliance must be earthed 8 Stainless steel door cleaning Important g instructions 28 Fitting a different plug 8 Upper spray arm 29 Water inlet hose connection 9 Lower spray arm 29 Drain Hose Connection 9 8 Before calling service 5 How to use 44 Trouble shooting 30 Water hardness amp regeneration settings 11 9 Guarantee Details 32 Water Hardness Level Adjustment Table 12 Adding Dishwasher Salt 13 Detergent use 13 Filling detergent dispenser 15 Rinse aid 16 Loading the dishwasher 17 Folding plate support rods 18 Movable Cutlery Basket 18 Upper basket height adjustment 19 Folding Tines 19 Basket insert with variable height settings 20 El Know your dishwasher specification x Removable a work top onl ge Turbo Fan Heat A F Pring System Top Spra Upper basket Li Upper spray arm Upper basket track latch Heating element concealed behind Dishwas
10. an Make sure the electricity and water connections of your dishwasher are in compliance with the instructions for assembly as stated in the relevant part of this booklet Any water remaining in the dishwasher after production should be carefully removed due to reasons of hygiene Therefore always select a pre wash programme before first use Pre wash or Economy programme Before the first wash add 1 It of water to the salt container of your machine When deciding on where to install your new dishwasher ensure that the position of your dishwasher makes it easy and quick for you to place the dishes in the dishwasher and also to take them out and store away after the dishwashing is completed Avoid placing the dishwasher where the ambient temperature is likely to fall below 5 degrees C 41 F When positioning your appliance take care not to damage your flooring pipes wall coverings etc Do not move the appliance by pulling by the door or handle Electrical requirements Before you insert the plug into the wall socket make sure that the voltage and the frequency shown in the rating label corresponds to your electricity supply We recommend that this appliance be connected to the mains supply via a suitable switched and fused socket in a readily accessible position If the supply cord or the mains lead is damaged please do not replace it yourself The supply cord or the mains lead must be replaced by a Blom
11. ater Setting this system correctly will increase the washing effectiveness To find out the water hardness level of water in your area contact your local Water Board or Determine water hardness level by the help of test strip provided If you move to a different location the level of water hardness will possibly be different It is essential to reset the water hardness in order to obtain optimum washing efficiency Test Strip Q r second f Level 1 No Lime lt Level 2 HL Very low lime content rf Ae Level 3 BN H Low lime content ale Level 4 NN EN EN Medium lime content H Level 5 E BN E E High lime content Level6 CE E m HN Um Very High lime content Remove the Letthe water Fill a glass with Take the test strip Hold for Set the water hardness level of your dishwasher test strip from flow from your tap water and outofthe water and 1 minute according to the result shown by the test strip its packing tap for 1 minute dip the test strip shake it into water for 1 second 11 GB To Adjust the Water Hardness 1 Press and hold the Programme Selection Key when the machine is off and press On Off button simultaneously to turn on your machine Release the Programme Selection Key when the water hardness level stored on your machine is displayed in r format 2 Start Stop icon will start flashing as soon as the water hardness lev
12. berg Authorized Service Agent or a similarly qualified person 7 GB Warning This appliance must be earthed If the fitted moulded plug is not suitable for your socket then the plug should be cut off and an appropriate plug fitted Destroy the old plug which is cut off as a plug with a bared cord could cause a shock hazard if inserted into a socket elsewhere in the house The moulded plug on this appliance incorporates a 13A fuse Should the fuse need to be replaced an ASTA approved BS1362 fuse of the same rating must be used Do not forget to refit the fuse cover In the event of losing the fuse cover the plug must not be used until a replacement fuse cover has been fitted Colour of the replacement fuse cover must be the same colour as that visible on the pin face of the plug Fuse covers are available from any good electrical store Important Fitting a different plug As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals on your plug proceed as follows 1 Connect the green yellow or green earth wire to the terminal in the plug marked E or with the symbol or coloured green and yellow or green 2 Connect the blue neutral wire to the terminal in the plug marked N or coloured black 3 Connect the brown live wire to the terminal in the plug marked L or coloured red With the alternative plugs a 13A
13. cated in the Programme Data and Table of Average Consumption Values Combi Tablet symbol 17 lights up when you select the Combi Tablet function 7 Time Delay Button 8 You can delay the start of the selected programme until 24 hours with increments of 1 hour by means of the Delayed Start Function Programme Selection You can select the desired programme after turning on the machine by pressing the On Off button 1 Switch to the programme you want to operate by pressing programme selection button 4 You can follow up the programme you are in from the programme indicator 10 on the screen Programme number will increase by one each time you press the programme selection button Number of the defined programmes can change depending on the model you have purchased The selected washing programme will start running when the Start Pause Cancel button 2 is pressed P symbol 12 light up Time indicator 11 will start displaying the estimated remaining time to the end of programme Total time can be different from the time indicated at the beginning since it can change while the programme is running depending on the temperature of the room where your machine is installed temperature of the water supply auto cleaning of the water softening system regeneration and amount of the dishes Adding Functions to the Programme With the help of the add function buttons you can run the selected programme to
14. ction button 4 e You can see the programme time in the Remaining Time Indicator 3 e f necessary you can change your washing programme as you prefer by means of the Add Function Buttons 5 6 7 8 e Start the programme by pressing the Start Pause Cancel button 2 WARNING Pay attention not to open the door of the machine when it is running Stop the machine by pressing Start Pause Cancel button 2 if you have to open the door Then open the door of your machine There may be a rush of vapor when you open the door of your machine be careful Close the door and press Start Pause Cancel button 2 again Programme will resume running e End of Programme indicator 20 d will light up e Turn off your machine by pressing On Off button 1 e Close the tap e Unplug the mains plug from the wall socket e Leave your dishes in the machine for about 15 minutes after they are washed in order to have them cooled down Your dishes will dry in a shorter time if you leave the door of your machine ajar during this period This will increase the drying effectiveness of your machine 26 GB uuuue1B6oud s3 ay Buisn pue Josa pie suu N e pue 1 su dsip jes 1 u ljos Ja eM in e ym JNO paleo aq 1snu ZrZ0S NJ uA 9uepioo2e ul S S9 SUL s l n nsui Buse Jo uuuue1Boid sousIEjoy suonipuo2o eonoeid sapun INDIO 31049194 ABW s oua y q suonipuo2 piepue s JOPUN p uluu p 919M lqe y u uwo
15. d on the voltage specified For electrical safety only earthed plugs and sockets should be used Always use the fused plug provided with the appliance The user is responsible for meeting these basic safety requirements The life of your machine and your safety depend on you using an electrical installation compliant to standards Do not use an extension cable When disconnecting your machine from the mains supply always pull from the plug Never pull the cord itself Children s Safety Never allow your children to play with your dishwasher This appliance is not intended for use by persons including children with reduced physical sensory or mental capabilities or lack of experience and knowledge unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety Dishwasher detergents contain irritants and abrasives These ingredients might have caustic effects in the eyes mouth and throat They can be extremely dangerous if swallowed Avoid contact with skin and eyes Check that the detergent receptacle is empty after completion of the wash cycle Keep detergents out of children s reach and do not put detergent in the machine until right before you start the washing programme The water in your dishwasher is not suitable for drinking for this reason do not allow your children near your machine when the front door is open Never allow your childre
16. dles items stuck together with adhesives plastic items not resistant to high temperatures Copper tin items and aluminium ware in your dishwasher As with hand washing some on glaze decorated china aluminum or silver have a tendency to discolour or fade Also certain types of glassware and crystals may lose their shine and become opaque in time A chemical reaction can occur between silver cutlery and stainless steel cutlery As a precaution do not wash together Iron and cast iron objects can rust and stain other items Pay special attention to whether or not the item you wash in the dishwasher is dishwasher proof If in doubt contact the manufacturer of the item Do not overload your dishwasher or do not load items other than those mentioned in this manual El Before first use EJ Installation After unpacking your dishwasher check the machine against any possible transportation damage Never install and use damaged machines If your machine is damaged contact your retailer Always have your machine installed by qualified electrician plumber to ensure correct installation Any repairs and maintenance work on this dishwasher should be carried out by authorised service staff only Unauthorised repairs are not only dangerous but also lead to the cancellation of your warranty If your dishwasher has an Internal Lighting incase of a defect broken lamps can be changed by an authorized service technic
17. el stored on your machine is displayed in r format 3 Select the water hardness level suitable to your machine from the Water Hardness Level Adjustment Table by pressing the Delayed Start Key 4 Press Start Pause Cancel key once to store the level you have selected 5 Start Stop icon will light continuously when the new water hardness level is stored 6 Press the On Off button to turn off your machine Water Hardness Level Adjustment Table Hardness English German French Position of Level Water Water Water regen m z Hardness Hardness Hardness eration Water Hardness Level Indicator Regeneration Adjustment dE dH dF adjust Switch switcl 1 Level 0 5 0 Press the Delayed Start key to switch I ii 1 s the water hardness level to position 1 E 2 Level 0 Press the Delayed Start key to switch ES the water hardness levalito position 2 re 3 Level 0 Press the Delayed Start key to switch 15 21 12 17 21 30 the water hardness level to position 3 rJ 4 Level 0 Press the Delayed Start key to switch th 22 28 18 22 31 40 the water hardness level to position 4 r q 6 Level 5 Level 0 Press the Delayed Start key to switch Very hard water CETIRI 29 42 23 34 41 60 the water hardness level to position 5 r5 If the tap water is excessively 6th degree hard set the water hardness 6 Level Press the Delayed Start key to switch adjustment to level 5 and Regenera ee 43 75 35 60 61 107 the water hardness level to
18. fuse must be fitted either in the plug or adaptor or in the main fuse box If in doubt contact a qualified electrician Green and yellow or green Blue or black Brown or red Water inlet hose connection Make sure your plumbing is suitable to install your new dishwasher If in doubt contact a qualified plumber The appliance must be connected to the water mains using the new hose set supplied with your new dishwasher Old hose sets must not be re used The water pressure coming from the water mains supply must be a minimum of 0 3 and a maximum of 10 bars Connect the straight end to your water mains supply Ensure plastic filter and black rubber seal is in place Please turn on the tap and check for leakages after connecting the hose We recommend the tap is turned off when the machine is not being used If you only have one cold water feed For example for your washing machine don t worry a Y adaptor will provide you with the additional cold water feed you need for your dishwasher Y adaptor is available from most DIY stores gt 9 O AFTA 40 a Drain Hose Connection Fit the drainage hose of your machine to the drainage pipe without bending Secure your hose firmly to the waste pipe to avoid it coming off during the washing process The waste pipe must only be connected into the foul drains and not surface water drainage system The hose should be placed between 50 cm and 110 cm
19. gether with the Half Load 1 2 5 Rapid 6 Combi Tablet 7 and Delayed Start 8 functions You will obtain a better drying performance if you select the Combi Tablet function in cases where you use a multi purpose detergent To add a function to the programme 23 GB 1 Select the programme by pressing programme selection button 4 2 Press the button of the function that you want to enable and check to see the indicator for the relevant function on the display 3 You can start the programme by pressing the Start Pause Cancel button 2 Programme Steps Follow up You can follow up the step while current programme is running from the Programme Steps follow up indicator 20 a Washing Step Indicator 20 a b Rinsing Step Indicator 20 b c Drying Step Indicator 20 c d End of Programme Indicator 20 d The display shows the steps for washing 20 a rinsing 20 b and drying 20 c respectively while the selected programme is running Only the End of Programme indicator 20 d lights up when the programme is over Remaining Time Indicator 3 displays 00 00 Cancelling a Programme Press Start Pause Cancel button 2 for three seconds to cancel a programme that is already running Release the button when P symbol 12 start flashing in the display For a couple of minutes the machine will fulfill the necessary operations required for cancellation Remaining time indicator 11 displays 00 00
20. gistered Gas Installer e The guarantee is given only within the boundaries of the United Kingdom and the Republic of Ireland The guarantee is applicable only to new products and is not transferable if the product is resold e BLOMBERG disclaims any liability for incidental or consequential damages The guarantee does not in anyway diminish your statutory or legal rights 32 GB 33 GB 34 GB 17 9539 0100 Revision AA 09 12 Blomberg 36 38 Caxton Way Watford Hertfordshire WD18 8UF Tel 0845 6048340 Fax 0845 6004922 email service blomberguk com www blomberguk com
21. he rinse aid dispenser e f you use combined detergents with a rinse aid setting higher than 1 hand contact may leave rainbow coloured water stains on the washed items and inside the machine e These detergents do not contain softening salt so you need to use the softening setting as described in the manual making sure that there is salt in the water softener with every wash and that you refill the water softener with salt every time it is empty Important warning Should you encounter a problem that has previously never occured after you start using these detergents contact the detergent manufacturer directly You will find contact details on the packet If you stop using this kind of detergent e Ensure that the salt and rinse aid dispensers are full e Put the water hardness setting at the highest level and run a wash cycle with the appliance empty e After washing while empty return the water hardness setting to the correct level for your mains water hardness shown in the manual e Put the rinse aid setting at the correct level Filling detergent dispenser If the dishwasher is considerably full and the dishes are relatively dirty fill the main container A up to 25cm level If the dishwasher is not quite full and the dishes are only slightly soiled fill the main container A only up to 15cm level If your dishes are kept unwashed for a long time and the food particles are stuc
22. her salt cap me liner ower Lower basket DB spray arm Cutlery basket BW Filters Detergent and Rinse aid dispenser Programme Selection amp Starting Guide Programme Selection Button Half Load Button On Off Button Rapid Button LCD Displa Combi Tablet Detergent Button Time Delay Button Start Pause Cancel Button Handle 3 GB Specification Load Capacity Height Width Depth Depth Height without worktop Net weight Supply voltage Fuse currrent Total power Heater power Pump powers Diameter of plates for Upper basket Lower basket 13 Place settings 850 mm 598 mm 598 mm 570 mm 820 mm 46 kg 220 240 V 50 Hz 13A 1900 2200 W 2000 W 90 30 W 25 cm max 31 cm max Because we continually strive to improve our products we may change our specifications and designs without prior notice Note for Testing Institutes The necessary information for performance testing will be provided upon request The request can be done by e mail through dishwasher standardloading com Please do not forget to write the model code stock code and serial number information of the appliance besides your contact information in the e mail The model code stock code and serial number information can be found on the rating label which is placed on the side of the door A Warning and safety information Electrical Safety The dishwasher should only be operate
23. k on the dishes also fill the small container B up to 5cm Depending on the degree of soiling and the water hardness in your area it may be necessary to add more detergent Powder and gel detergents are poured into the dispenser If you are using tablet detergent read the manufacturer s recommendations on the packaging in order to determine where the tablets should be placed inside the dishwasher detergent dispenser cutlery basket etc After you put in the detergent shut the container lid D and ensure you hear the clicking sound During the wash programme the detergent will dispense automatically and the lid D will remain open when the programme finishes Do not use detergent when using the pre wash programme 15 GB Detergent residues Regular use of low temperature washes and or short duration programmes can lead to undissolved detergent residue build up We recommend to carry out a service wash at the highest temperature possible every 3 4 months with the dishwasher empty and without using detergent It is not recommended to carry it out with auto programme Rinse aid Use only rinse aid intended for household dishwashers The rinse aid is specially formulated to be used in the dishwashers for the prevention of watermarks and scale on dishes and to increase the efficiency of the washing and drying processes Therefore make sure that there is adequate amount of rinse aid in the
24. n to play on or sit onto the front door when the front door is open After unpacking your machine keep the packing material out of children s reach Warning Long cutlery such as ladles and long knives etc must be placed horizontally on top of the full cutlery basket or on the racks to prevent accidental injury General This dishwasher has been designed to clean your dirty dishes at home Never use chemical solvents in your machine this may lead to explosion risk Never use materials other than specially produced softening salts in the salt dispenser of your machine Never use materials other than specially produced detergents and rinse aids in the detergent and rinse aid dispensers of your machine Please dispose of the packaging material and old appliances carefully Please ensure old machines do not become a threat to child safety It is known that children lock themselves in unused machines To avoid such a problem it is advised that you cut the mains cable off and break the door latch so it does not lock 5 GB The door of your machine is designed to support the weight of a full basket when the lower basket is pulled all the way out Never place any other load on the door otherwise the machine may tip over After using the dishwasher always close the door as an open door can be a hazard Do not open the door whilst the appliance is in operation Recycling Please help us to protect our environme
25. nt Packing materials and some parts of your machine are produced using recyclable materials These materials are marked up with recycling symbol and material type information gt PE lt gt PS lt gt POM lt These raw materials should not be mixed with general refuse and should be given to recycling centers We suggest you contact your local authority for disposal information and facilities available This product bears the selective sorting symbol for waste electrical and electronic equipment WEEE mes This means that this product must be handled pursuant to European Directive 2002 96 EC in order to be recycled or dismantled to minimize its impact on the environment For further information please contact your local or regional authorities Electronic products not included in the selective sorting process are potentially dangerous for the environment and human health due to the presence of hazardous substances 6 Energy and water saving Scrape excess food from the dishes before loading Start your dishwasher after fully loading the machine Do not use the pre wash programme unless required Make your programme selection as per the programme chart and quick reference guide supplied What should not be washed in your dishwasher Do not wash items soiled with cigarette ash candle paint wax dyes chemicals etc since these may damage your machine Do not wash forks knives and spoons with wooden or bone han
26. o use this insert in the lower basket for glasses and long handled cutlery utensils If you do not need the insert fold the rack upwards at the angle shown A Push the entire insert upwards B Place the insert in the upright position C Push the insert downwards and lock it into place with the holder D When you want to use the basket again reverse the procedure To set the height push the rack upwards and fold it open in position G When finished check that the sprayer arm can still move freely 20 GB 6 Programme Selection and Operating Your Machine El El Hl On Off button E Rapid button Start Pause Cancel button Combi tablet detergent button Display EJ Time delay button Programme selection button EJ Handle Half load button Programme indicator Rapid indicator Time display Programme and delay Salt indicator Delayed Start Indicator Child lock Rinse Aid Indicator Progress indicators EI Wash Half Load 1 2 indicator EJ Rinse Fi Dry EI End 21 GB On Off Button Start Pause Cancel Button Display Programme Selection Button Half Load Button Rapid Button Combi Tablet Detergent Button Time Delay Button Handle 0 Programme Indicator 1 Remaining Time Indicator Time Delay Active Indicator 12 Start Indicator
27. of functional replacement parts but excluding consumable items The labour costs of a BLOMBERG approved repairer to carry out the repair What is not covered Transit delivery or accidental damage or misuse and abuse e Cabinet or appearance parts including knobs flaps handles or container lids e Accessories or consumable items including but not limited to ice trays scrapers cutlery baskets filters and light bulbs e Repairs required as a result of unauthorised repair or inexpert installation that fails to meet the requirements contained in the user instruction book e Repairs to products used on commercial or non residential household premises e Loss of frozen food in freezers or fridge freezers Food loss insurance is often included within your household contents insurance policy or may be available separately from your retailer Important notes e Your BLOMBERG product is designed and built for domestic household use only e The guarantee will be void if the product is installed or used in commercial or nonresidential domestic household premises e The product must be correctly installed located and operated in accordance with the instructions contained in the User Instructions Booklet provided e Professional installation by a qualified Electrical Domestic Appliance Installer is recommended for all Washing Machines Dishwashers and Electric Cookers e Gas Cookers must only be installed by a Gas Safe or BORD GAIS re
28. oing to be used for a long period of time switch off turn off the water clean and leave the door ajar Stainless steel door cleaning instructions Only valid for stainless steel models which have x suffix in the model number Stainless steel surfaces of your appliance require special cleaning methods In order to eliminate marks on doors and to keep your appliance doors clean we recommend you the following to clean and wipe the stainless steel surfaces of doors 1 You can purchase special cleaning materials suitable for stainless steel surfaces of kitchen appliances from your local store Follow the instructions supplied by the manufacturer of such cleaning materials 2 You can purchase a special micro fibre cleaning cloth pack called E cloth from your local electrical or hardware store which is suitable to clean and wipe stainless steel surfaces of kitchen appliances without the need to use any chemicals or other cleaning materials You just need warm water You need to follow the instructions supplied inside the packaging of E cloth 3 Never attempt to clean wipe or treat the stainless steel and other surfaces of your appliance with unsuitable material do not clean or wipe handles and plastic surfaces using stainless steel cleaning materials otherwise your guarantee will be void How to clean the filters and spray arms filters For the efficient operation of your dishwasher check the filter
29. ooting Before calling service check the following amp Trouble shooting guide supplied on Is the dishwasher door closed firmly Are the filters clogged Is the water mains supply fully A J Is the detergent dosage and or turned on a rinse aid sufficient Is there enough salt in the water softener Is the machine switched on TROUBLE SHOOTING GUIDE SYMPTOMS POSSIBLE CAUSES SOLUTIONS Insufficient amount of Increase the amount of detergent especially when detergent washing full loads or in hard water Increase water softener dosage Use additional Hard water detergent increase rinse agent dosage Check the nozzle holes in the spray arms They may Spray arms need cleaning be blocked with a soil particle Check and clean them periodically Follow instructions for use for proper loading procedures Place dishes so water spray reaches all soiled surfaces Do not overcrowd the baskets since this will block the water spray Insufficient water fill Check mains water pressure cleaning results Mproper loading Remove any accumulated or deposited foods Check Filter sysiem needsicleaning and clean them periodically Oversudsing Prewashing with Rinse items thoroughly before putting them in the a liquid dishwashing detergent dishwasher to remove dishwashing detergent Check to be sure water action is not blocked by ater not reaching surfaces j dishes Check filter system for accumulated or dish
30. perature Use of a rinse aid may also help If using powder detergent here may be dampness in the dispenser Improper loading Make sure dispenser is dry before adding powder detergent Start dishwasher immediately If using gel detergent the detergent may be left in Start dishwasher soon after adding gel detergent Do dispenser too long before not allow detergent to dry out in dispenser using Do not overfill Cover should close tightly Check Faulty cover cover for fit Improper loading Do not place large items in front of dispenser Use detergent within one to two months of purchase To assure freshness buy detergent as needed and Old detergent I no more than one or two at a time Store in a cool dry place Load with care following the instructions for use Improper loading Place glassware so it does not touch the other dishes Remove from dishwasher carefully Use the pre wash cycle at least once a day until a load accumulates or hand rinse dishes before loading dishwasher Dishes washed only every two or three days A dirty filter system may contribute to a bad odour Clean nitensystem 31 GB 9 Guarantee Details Your new BLOMBERG product is guaranteed against the cost of breakdown repairs for three years from the date of the original purchase What is covered e Repairs necessary as a result of faulty materials defective components or manufacturing defect The cost
31. position 5 cS tion Adjustment Switch to position 1 If the hardness level of the water that you use is above 80 dF French standard for water hardness or if you are using well water then it is recommended to use filter and water purification devices If the hardness level of the water that you use is below 9 dF French standard for water hardness there is no need to use salt in your dishwasher If the water hardness adjustment is set to level 1 the No salt warning indicator will illuminate continuously although it is not necessary to use salt If you use salt under this condition salt will not be consumed and the lamp will not illuminate 12 GB Adding Dishwasher Salt Only use special pelletized dishwasher salt in your machine to soften the hard water Never use other types of salts including table salt animal feeding salt sea salt culinary salt These types of salt do not dissolve in water easily and will damage your appliance beyond repair When you run the dishwasher the Water softener will be full of water Therefore adding softening salt should always be done immediately before you start the dishwasher Caution Only fill with salt just before starting one of the complete washing programmes to prevent any grains of salt causing corrosion Ensure 1 Litre of water has been added You can put approximately 2 kg softening salt in the Water softener To fill the container
32. re placing in the dishwasher to avoid clogging the filters There are three separate baskets in which you can put your dishes Place large or heavily soiled items in the lower basket and small light or delicate articles in the upper basket Put forks small and medium size knives and spoons in the cutlery basket Place tall narrow items in the middle of the racks Long stemmed glasses should lean against the basket the racks or the supports not against the dishes The shelves on the rack are made height adjustable to accommodate tall items When loading your dishwasher please ensure tall glasses and or wine glasses rest against the sides of the upper basket Do not allow tall glasses to rest against each other since they may be damaged during washing if not properly supported Always arrange saucepans cups and glasses etc upside down You can fold the racks in the upper basket when you need more space for larger items 17 GB Folding plate support rods There are four separate folding plate support rods in the lower basket of your dishwasher designed to allow you more space to accommodate saucepans and large bowls in the lower basket You can either fold each section 1 2 3 4 individually or all at once to create a large emp
33. rinse aid dispenser of your machine You can adjust the amount of rinse aid used during the wash programme by turning the rinse aid dispenser regulator C The dispenser regulator C may be set between levels 1 and 6 6 being the maximum amount of rinse aid usage Your machine is pre set at the factory to level 4 According to the finish and drying results obtained adjust the dose of rinse aid by means of the six position selector Position 1 minimum dose Position 6 maximum dose Gradually increase the dose if there are drops of water or lime spots on the dishes after washing Reduce it if there are sticky whitish streaks on the dishes Filling the rinse aid dispenser Open the rinse aid dispenser lid by pressing the button as shown in the diagram Fill up with rinse aid until the container is full to level of max mark Put the lid E on and ensure you hear the clicking sound Remember to CLOSE the lid after every refill Make sure you clean any rinse aid that you might have spilled Visual indicator Dark sufficient rinse aid Light add rinse aid 16 GB Loading the dishwasher Loading the dishwasher correctly will increase the washing drying and energy performance of your machine Examine the information given in this section and the information stated in the Programme chart and quick reference card given with the manual Remove any large scraps of food from the dishes befo
34. s and the spray arms regularly There are three different filters in your machine Main filter Coarse filter Micro filter To remove the coarse and micro filter assembly to clean turn it anti clockwise as far as it goes and lift it up Then press the two tongues inwards and pull out the coarse filter 28 GB Pull the main filter off Clean all three filters under running tap water with a brush Reinsert the main filter in its place Place the coarse filter into the micro filter Ensure the marks align properly Turn the coarse filter clockwise until you hear a clicking sound It is important that you fit the filters correctly Caution the dishwasher must not be used without filters Incorrect repositioning of the filters will produce poor washing results Cleaning of the filters is vital to ensure correct operation of the machine Upper spray arm Turn the nut anti clockwise and remove both the nut and the spray arm Flush away food particles under running water Put the spray arm back on and screw on the nut turning clockwise until a clicking sound is heard Lower spray arm Remove the spray arm from its slot by releasing the catches and pulling it upwards Flush away the food particles under running water Reinsert the spray arm back into its original position Main filter Coarse filter Micro filter 29 GB 8 Before calling service Trouble sh
35. selection button Number of the selected programme appears in the programme indicator 10 on the display 3 in the format of Pl reed Programme number will increase by one each time you press the programme selection button Number of the defined programmes can change depending on the model you have purchased Half Load Button 5 If you want to run your machine without loading it completely place your dishes into the machine as you desire First press the On Off Button 1 Select the desired programme and press the Half Load 5 button You must see the Half Load indicator 15 1 2 appearing on the screen Start the programme by pressing the Start Pause Cancel button 2 Thanks to the Half Load option you can use both lower and upper baskets of your machine and you can save water and energy 22 GB Turbo fan heat drying system Turbo Fan Heat Drying System ensures your dishes are dried efficiently During operation you may hear fan noise which is normal Rapid Button 6 This option allows you to shorten the selected programme the dishwasher then uses higher water pressure and consumes less energy and water Combi Tablet Button 7 To obtain a better drying performance from the multi purpose detergents called as all in one detergents such as 2in1 3in1 4in1 5in1 and etc depending on the hardness level of the tap water The programmes in which the Combi Tablet function can be enabled are indi
36. switched off press Half Load 1 2 button 5 and then On Off button 1 to switch it on 25 GB e Half Load 1 2 button 5 pressed and release On Off button 1 e Keep Half Load 1 2 button 5 pressed for three seconds more e Rinse Aid Indicator 14 comes on and the stored rinse aid indicator status of your machine appears on the display in the format of ON or OFF e You can change the status of the indicator as ON or OFF with Start Pause Cancel button 2 If you switch off the machine with On Off button 1 when the status is ON then the rinse aid indicator will come on when the rinse aid level in your machine becomes low while the machine is in use If you switch off the machine with On Off button 1 when the status is OFF then the rinse aid indicator will never come on Starting Your Machine e Plug the mains plug into the wall socket Open the tap Open the door Place the dishes Check if the upper and lower spray arms rotate freely e Put sufficient amount of detergent in the detergent dispenser and close its lid e Press On Off button e Check if the salt and rinse aid warning indicators 18 14 are lit and add salt and or rinse aid if needed e Determine your washing programme with the aid of the Programme Data and Table of Average Consumption Values e You can select the determined washing programme by pressing programme sele
37. ty space Simply press the handgrips A and fold them down Movable Cutlery Basket Designed to allow free placement of the dishes according to their size the movable cutlery basket can slide over the tines to the left A and right B side 18 GB Upper basket height adjustment The upper basket is equipped with a lifting mechanism which enables you to change the height of the basket even if it is fully loaded and without having to remove it from the dishwasher The height of the upper basket was set at the factory to the lowest position To lift the upper basket to the high position hold it on one side and carefully pull it upwards To lift the opposite side of the basket hold it and pull it upwards in the same manner To lower the upper basket hold the basket lever on one side and carefully lower the basket without releasing the lever O Repeat the procedure with the lever on the opposite side of the basket Make sure that both levers catch in the same height position Folding Tines There are folding tines in the upper rack to allow you more space to accommodate glasses or cups Simply pull in the first front folding tine move it to left A and right B to place in another positon When you need take the tines down until the tines fall down 19 GB Basket insert with variable height settings You can als
38. us s njea uonduunsuo2 By pug pug pua A A u N i i N suondo jnoulw lt surd JOH Aq suly JOH suly OH pug ou nb s uutue1Boid m 27 A A A A A 9SUL PjOD asuly JOH sul ploO suu pjoo asuly JOH A A A A A Buljlos Jo Junowe y yseMm suu plod yseMm yseMm sul POD pug o p lsn pe s 2u nb s A A A A wweosd u 1 ySem ld ySem ld ySem ld ySem ld eld S 8 W9 G U GZ W atv atv sjuabi9 0q Builios jo ae16eq p ue l o Ajayajdwoo ae uuuuge1Boid 1o l s s ys p pun s ysem pue ysem aid JOH seynullu s usip pallos llguuou u u peol jin Bunreme I A SSOUIPIP 1EM Buninbas gg ul Buluesj ssejo y JO sluwesBod ouemsse B uuuug16oid ajnulw 0 np s u soo pue s su s lleoneuuolnv s usip payios AllAg H s ys p pajios AnuB 1 SILIOU009 8 JSON pue saysip l qa s usip p llos AnuB 1 suu 0 YSEM 31q ainyesoduia Buiue l5S lqe1_ wwepold How to clean your dishwasher Cleaning your machine at regular intervals ensures longer product life and reduces the risk of recurring problems Clean spray arms and in particular filters at least once a week Always unplug the appliance and turn off the water supply before cleaning To clean the outside of the appliance and the door seal use a neutral detergent and a damp cloth To clean the control panel use only slightly damp cloth Do not use abrasive detergents Ifthe appliance is not g
39. washer overcrowded deposited food or detergent Load dishwasher correctly Keep filter system clean Small particles Insufficient water fill Check mains water pressure Use powder detergent within one to two months after purchase Open one box at a time Always close pouring spout after each use Store in a cool dry place Rinse aid supply depleted Add rinse aid to the dispenser 30 GB Powder detergent stored oo long or under adverse conditions Pitting of stainless steel items Dishes not dry Scratches on glassware Remove spots with silver polish Rewash Wash soon after use or pre wash items if they will not be washed right away Do not overload cutlery basket Avoid spilling or pouring detergent directly on flatware Make sure dispenser cup is properly closed Prolonged contact with salty or highly acidic foods or ith undissolved or highly concentrated detergent Load so that all items are properly tilted for good drainage Avoid nesting of dishes and or silverware Rinse aid supply depleted Add liquid rinse aid The condition may not always be preventable To A water or chemical reaction minimize the possibility of etching use minimum ith some glassware Usually amount of detergent caused by some combination of soft or softened water and alkaline washing solutions reacting with the glassware Use of the appropriate programme Can be accelerated by poor rinsing overloading and lexcessive tem
40. yed start indicator Z sand glass 13 and play icon 12 will remain lit on the display during the delayed start countdown and the Time Delay Active Indicator 11 will display the remaining time Programme will start automatically when the countdown is over 24 GB You can use the delayed start function if you are utilizing the economic electricity tariff If you want to change the programme or functions while the delayed start function is enabled then pause the machine by pressing the Start Pause Cancel button 2 You will see that the countdown stops The delayed start indicator amp will start flashing Select the new programme and or add the functions as described in Programme Selection and Table of Average Consumption Values Resume the delayed start countdown by pressing the Start Pause Cancel button 2 If you want to cancel delayed start countdown while it is in progress then press the Start Pause Cancel button 2 for three seconds Release the button when P symbols 12 start flashing in the display For a couple of minutes the machine will fulfill the necessary operations required for cancellation Remaining time indicator 11 displays 00 00 You may select and operate a new programme following the delayed start countdown cancellation process If you want to select a new delayed start time while the delayed start countdown is in progress then pause the machine by pressing the Start Pause
Download Pdf Manuals
Related Search