EagleEye - Advantech
Contents
1. need to install software on your host system to setup or operate the EagleEye system Take note of the following before attempting to access the application 1 EagleEye vision systems are preconfigured with a default static IP address of 192 168 0 100 2 The PC used to access EagleEye initially will need to be configured on the same network neighborhood but with a different address i e 192 168 0 101 Consult your system administrator for instructions on how to do this The subnet mask should be set automatically to 255 255 255 0 3 This static IP address can be changed at any time through the EagleEye web server interface to match your Local Area Network Click on the Setup Device hot link to change the network address Remember to keep a record of what the new address is set to EagleEye supports both DHCP and Static IP addressing preferred since the address does not change NOTE A power cycle is required before the new ad dress will take effect 4 f you incorrectly set or forgot the new address of your EagleEye you can run the iDiscover utility This program is installed automatically when you click on the Inspector Express or upgrade hot links in the web server interface This program is also on the Inspector emulator CD that ships with the system 5 In most cases you will need administrator privileges on your PC to access EagleEye It may be necessary to customize the security settings on your br2. EagleEye Vision System Dec 2012 Part No 2003102460 Connecting the EagleEye Vision System This section details how to connect the EagleEye vision system with its associated components and factory environment Camera Connectors and Indicators Reset LAN LED 4 M12 8 Pin Female LAN Connector 10 100 BaseT Ethernet connection Pro vides the primary interface for configuring the camera developing the application and monitoring results NOTE The camera can be powered from the Ethernet cable directly Passive Power over Ethernet Provides access to the camera I O 2 IN 2 OUT Opto Also provides PWR input I O PWR 12 30V Provides PWR and strobe control to a local LED light source NOTE Lamp PWR is identical to EagleEye PWR input The LAMP camera should be powered from a 12V PWR source if the light requires a 12V supply Recommend 24V supply Green Inspection Pass runtime Blue blink Booting should stop after 20 LED2 seconds Blue Inspection Recycle runtime Red Inspection Fail Runtime Blue Solid Camera booted not LED1 configured Green blink Solution loaded acquisition in process Green Solid Solution loaded Red Camera Fault EagleEye Startup Manual Red Green Yellow Network activity LAN LED Blue Warm Reset TWANVWIN dNLuVls HOILNVACGV Cable Pinouts The EagleEye vision
3. to the breakout screw terminals labeled PWR 5 Connect the Lamp via corset AEE L 5E amp AEE L 10E between the camera M12 5 and the lamp Setup Computer PLC or Factory Network AEE PL 1W0E AZE E SE amp AEE 10E iat Cats Cabie EagleEye System LED Lamp AEE L SE amp AEE L 10E Ethernet and I O Setup with Lamp 1 Connect the M12 8 male end of the Ethernet cordset AEE E 5E amp AEE E 10E to the M12 8 female connec tor labeled LAN on the camera 2 Connect the RJ45 end of the Ethernet cordset to the RJ45 connector labeled CAM LAN on the Panel Link breakout module AEE PL 100E 3 Connect the RJ45 labeled LAN on the breakout module to the controlling PC PLC or the factory LAN 4 Connect camera PWR GND and I O from the control panel to the breakout screw terminals 5 Connect the M12 8 male end of the O PWR cordset AEE IO 5E amp AEE IO 10E to the M12 8 female con nector on the camera labeled I O PWR 6 Connect the open ended wires of the IO PWR cordset to their respective connections on the breakout module Setup Computer PLE or Factory Metwark ABE PL 100 AEE E 5E AEE E 10E Eagle ye System LEO Lamp kA AEE L 5E amp AEE L 10E Precautions Handling Precautions Care should always be exercised when handling and operating your EagleEye Vision System Even though the system is encased within a rugged industrial enclosure incorrect use or handling
4. EagleEye Vision System EagleEye Vision System Components EagleEye vision systems are shipped with the components listed below Take a few moments to verify that everything has arrived in good condition If your product has been vis ibly damaged during shipment or is missing parts please contact your Advantech representative immediately EagleEye Vision System Fully integrated vision system with 640x480 1024x768 1280x960 1600x1200 mono or color sensor processing engine EagleEye Vision System Inspector Express embedded software communications and light control CD including PC emulation software and associated product manuals Optional components sold separately M12 RJ45 Ethernet cordset 5M amp 10M M12 single ended IO cordset 5M amp 10M M12 single ended lamp cordset 5M amp 10M M12 I O to AEE PL 200 cable 5M M12 Lamp to AEE PL 200 cable 5M Component Cables AEE E 5E amp AEE E 10E AEE IO 5E amp AEE 10 10E AEE L 5E amp AEE L 10E AEE PL21I0 5E AEE PL2L 5E AEE PL 100E AEE PL 200 IEE AEE PL 200 IOE AEE PL 200 EE Panel Link breakout modules Provide Ethernet power and convenient panel access to EagleEye I O AEE MB 0E Right Angle mounting block For more information on this and other Advantech products please visit our websites at http www advantech com eAutomation For technical support and service http support advantech com tw This startup manual is for
5. can result in damage to your investment To prevent this we recommend you avoid the following e Hot plugging cables and devices Be sure to shut the system down and remove power before connecting or disconnecting anything to it Free standing operation It is advisable to mount the system properly to prevent it from falling accidentally Mounting holes are provided on each side of the system Operating the system in an environment outside of it s recommended operating conditions Electro Static Discharge Avoid the damage that ESD can cause Never expose the internal electronics to a potentially hazardous environment by opening the enclosure Doing so may cause serious damage User Service Warning This product has no field replaceable components Tam pering with the unit will void the product warranty Warranty Advantech warrants the EagleEye Vision System against defects in materials and workmanship for a period of 24 months from the date of delivery Advantech and its repre sentatives expressly disclaim any and all other warranties EagleEye Startup Manual 3 Getting Started The EagleEye vision system is supplied with the Inspector Express vision application embedded This application of fers a suite of vision capabilities to satisfy a diverse range of automated inspection needs The application interface is accessed through the Ethernet connection using a PC with Microsoft Internet Explorer 6 or higher You do not
6. cess to the device 6 Using the iNspect software refer to the Inspector Ex press user manual set up an application and store the solution on the camera Exit the application and return to the web server interface 7 The History Log hot link offers a quick and convenient way to view and store inspection results to an Excel spreadsheet on your host PC This feature is also avail able from within the Inspector Express application using the scripting tool
7. n nectors 4 n all configurations the Lamp cable can be connected between the camera and a compatible LED light source The EagleEye vision system supplies power and strobe control to the external light Power is routed from camera power input to the lamp BEWARE Connecting a voltage on pin 1 of the lamp connector that is lower than the input power voltage to EagleEye could result in damage to the camera Panel Link Module AEE PL 100E The AEE PL 100E module is an optional module that provides a safe and convenient way to interface EagleEye It provides an isolation layer between the factory and the camera differential isolation as well as supplying power via the Ethernet cable for single cable applications The AEE PL 100E also provides a manual trigger button and status lights for application debug AEE PL 100E NOTE The EagleEye vision system does not support the IEEE 802 3af standard Power over Ethernet PoE and should not be directly connected to a PoE supported router Ethernet Only Setup with Lamp 1 Connect the M12 8 male end of the Ethernet cordset AEE E 5E amp AEE E 10E to the M12 8 female connec tor labeled LAN on the camera 2 Connect the RJ45 end of the Ethernet cordset to the RJ45 connector labeled CAM LAN on the Panel Link breakout module AEE PL 100E 3 Connect the RJ45 labeled LAN on the breakout module to the controlling PC PLC or the factory LAN 4 Connect camera PWR and GND
8. owser to download and run ActiveX controls 6 f for any reason you can not access EagleEye from your internet browser you can install the emulator applica tion from the shipping CD and connect to the camera through this interface This step is explained in more detail later in the manual 7 EagleEye is compatible with host computers running the Windows XP operating system EagleEye has also been verified on the new Windows 7 O S 4 EagleEye Startup Manual EagleEye Web Server The EagleEye web server is a portal through which the EagleEye system can be set up and configured for an application The web server is accessed from a host PC using Microsoft Internet Explorer version 6 or higher as follows 1 Open Internet Explorer on the configured PC connected to the camera 2 Enter the URL address of the camera 192 168 0 100 and click go 3 The camera web server interface will be displayed in the browser as follows 4 The web server provides a quick snapshot of the state of the camera and provides controls for language selection IP address setup firmware upgrading and image backup or restore The web server is the portal into the inspect application and can be set up to prevent unauthorized access 5 Click on the Inspector Express hot link to launch the application The camera will automatically install some software components on the host PC when it connects for the first time These components set up the remote ac
9. system is compatible with M12 fac tory cordsets as show below LAN Connector Pinout and Cordset AEE E 5E amp AFE E i0E AEEO 5E amp AEE 40 10 ames PWR ea Brown RSZIZ RE Whine GND Blue STR Aleck RSZ TA Gray AEE L E amp AEE L 10E For Passive Power over Ethernet 2 EagleEye Startup Manual Cable Configurations The EagleEye vision system offers flexible cabling options to suit a number of application configurations 1 For single cable applications the Ethernet cable can be used to supply power referred to as Passive Power over Ethernet and communications between the camera and the control environment Power is supplied by connecting a DC voltage source between 12 30V to conductors 4 pwr and 8 gnd on the Ethernet RJ45 connector Note The AEE PL 100E module does this automatically In this configuration the camera I O is unavailable 2 For single cable applications that do not require a run time Ethernet connection the I O PWR cable provides limited communications and power between the camera and the control environment Note Ethernet is still required for setup 3 For typical applications both the Ethernet and I O PWR cables are connected to provide flexibility between the camera and the control environment In this configura tion either or both cables can supply power provided they come from the same power source Do not connect different power sources to the EagleEye camera co
Download Pdf Manuals
Related Search