Home

Manual

1. FDX stands for FULL DUPLEX Off Ethernet Connection in half duplex mode Ethernet Extender Remote Steady The device operates in remote mode Local Steady The device operates in local mode Error Steady Error occurred Link Steady valid connection established Green 1 5Mbps up to 2 600M 8 530ft Amber 6 10Mbps up to 2 400M 7 874ft Green 11 16Mbps up to 2 000M 6 561 ft Amber 17 20Mbps up to 1 800M 5 905ft Green 21 29Mbps up to 1 600M 5 249ft Amber 30 43 up to 1 400M 4 593ft Green 44 54Mbps up to 1 200M 3 937ft Amber 55 63 up to 1 000M 3 280ft Green 64 74Mbps up to 600M 1 968ft Amber 75 85 6 up to 200M 656ft User s Manual 10 100Base TX Hardened Ethernet Extender Installation This chapter gives step by step installation instructions for the Hardened Ethernet Extender Selecting a Site for the Equipment As with any electric device you should place the equipment where it will not be subjected to extreme temperatures humidity or electromagnetic interference Specifically the site you select should meet the following requirements The Surrounding Air temperature should be between 40 to 75 degrees Celsius The relative humidity should be less than 95 percent non condensing Surrounding electrical devices should not exceed the electromagnetic field RFC standards Make sure t
2. M12 2 LEDs Link ACT FDX BNC 9 LEDs Remote Local Error Link 1 2 3 4 5 Dimensions 50mm W x 110mm D x 135mm 1 97 W x 4 33 D x 5 31 H Weight 0 8Kg 1 76lbs Power Terminal Block 12 48VDC DC Jack 12VDC External AC DC required Current Consumption Operating Voltage amp Max 0 48A 12VDC 0 24A 9 24VDC 0 12A 48VDC Power Consumption 5 76W Max Operating Temperature 40 C 75 C 40 F 167 F Tested for functional operation 40 C 85 C 40 F 185 F UL508 Industrial Control Equipment certified Maximum Surrounding Air Temperature 75 C 167 F Storage Temperature 40 85 C 40 F 185 F Humidity 5 95 non condensing Safety UL508 EMI FCC Part 15 Class A VCCI Class A EN61000 6 4 EN55022 EN61000 3 2 EN61000 3 3 User s Manual 10 100Base TX Hardened Ethernet Extender EMS EN61000 6 2 EN61000 4 2 ESD Standard EN61000 4 3 Radiated RFI Standards EN61000 4 4 Burst Standards EN61000 4 5 Surge Standards EN61000 4 6 Induced Standards EN61000 4 8 Magnetic Field Standards Environmental Test Compliance Vibration Resistance EN61373 IEC60068 2 6 Fc Shock EN61373 IEC60068 2 27 Ea Free Fall IEC60068 2 32 Ed NEMA TS1 2 Environmental requirements for traffic control equipment User s Manual
3. up this device You only need to have one power input connected to run the Hardened Ethernet Extender Step 1 Connect the DC power cord to the plug able terminal block on the Hardened Ethernet Extender and then plug it into a standard DC outlet Step 2 Disconnect the power cord if you want to shut down the Hardened Ethernet Extender Power Input Assignment Power1 12VDC DC Jack Power 12 48VDC Power Ground Power3 fe du Des Terminal Block Power Ground Earth Ground DIP Switch Assignment Loc The device operates in local mode Rmt The device operates in remote mode User s Manual 10 100Base TX Hardened Ethernet Extender Specifications Applicable Standards IEEE802 3 10Base T IEEE802 3u 100Base TX Ethernet over VDSL Ethernet Extender Fixed Ports 1 x 10 100Mbps Ethernet port with M12 4Pin D type female connector 1 x Ethernet Extender port with BNC connector Speed 10Base T 10 20Mbps for half full duplex 100Base TX 100 200Mbps for half full duplex 1 5 10 20 30 40 50 60 70 75Mbps Switching Method Store and Forward Forwarding rate 14 880 148 810pps for 10 100Mbps Cable 10Base T 100Base TX Ethernet Extender 2 pair UTP STP Cat 3 4 5 up to 100m 2 pair UTP STP Cat 5 up to 100m Coaxial cable 5C2V RG58AU RG6AU LED Indicators Per Unit 3 LEDs Power1 Power2 Power3 Per Port
4. 02 3x Auto negotiation 10 100Mbps full half duplex Auto MDI MDIX e Ethernet Extender port BNC connector Symmetrical on the VDSL full duplex 85Mbps communications link over existing coaxial cable e Provides BNC to F Type connector e One DIP switch for configuring Local Loc and Remote Rmt User s Manual 10 100Base TX Hardened Ethernet Extender Ten speeds with speed indicator LEDs on front panel of unit up to 85Mbps about 200meters 656ft down to 1Mbps about 2 600meters 8 530ft Operating voltage and Max current consumption 0 48A 12VDC 0 24A 24VDC 0 12A 48VDC Power consumption 5 76W Max Power Supply Redundant 12 48VDC Terminal Block power inputs and 12VDC DC JACK with 100 240VAC external power supply Field Wiring Terminal Use Copper Conductors Only 60 75 C wire range 12 24 AWG torque value 7 Ib in Operating temperature range 40 C to 75 40 to 167 F Tested for functional operation 40 C to 85 40 F to 185 F UL508 Industrial Control Equipment certified Maximum Surrounding Air Temperature 75 167 F For use in Pollution Degree 2 Environment Supports Din Rail or Panel Mounting installation Packing List When you unpack this product package you will find the items listed below Please inspect the contents and report any apparent damage or missing items immediately to our authorized reseller The Hardened Ethernet Extender User s Manual AC to DC Po
5. 10 100Base TX Hardened Ethernet Extender Quick Start Guide This quick start guide describes how to install and use the Hardened Ethernet Extender The Hardened Ethernet Extender introduced here provides one channel for Ethernet over existing coaxial cable This is the Hardened Ethernet Extender of choice for harsh environments constrained by space Physical Description The Terminal Block and Power inputs Power Input Assignment Power1 12VDC DC Jack Power 12 48VDC Power Ground Power3 12 48 Terminal Block Power Ground e Earth Ground DIP Switch Assignment Loc The device operates in local mode Rmt The device operates in remote mode e DC Terminal Block Power Inputs There are two pairs of power inputs can be used to power up this Ethernet Extender Redundant power supplies function is supported You only need to have one power input connected to run the Ethernet Extender e DC JACK Power input 12VDC User s Manual 10 100Base TX Hardened Ethernet Extender The 10 100Base TX Connector The 10 100Base TX Connection The following lists the pinouts of 10 100Base TX M12 4Pin D type female port Pin Regular Ports Uplink ports 1 Output Transmit Data Input Receive Data Input Receive Data Output Transmit Data Output Transmit Data Input Receive Data Input Receive Data Output Transmit Data AJN The
6. Operates transparent to higher layer protocols such as TCP IP Ethernet port M12 connector Supports IEEE802 3 802 3u 802 3x Auto negotiation 10 100Mbps full half duplex Auto MDI MDIX Ethernet Extender port BNC connector Symmetrical on the VDSL full duplex 85Mbps communications link over existing coaxial cable Provides BNC to F Type connector User s Manual 10 100Base TX Hardened Ethernet Extender One DIP switch for configuring Local Loc and Remote Rmt Ten speeds with speed indicator LEDs on front panel of unit up to 85Mbps about 200meters 656ft down to 1Mbps about 2 600meters 8 530ft Operating voltage and Max current consumption 0 48A 12VDC 0 24A 24VDC 0 12A 48VDC Power consumption 5 76W Max Power Supply Redundant 12 48VDC Terminal Block power inputs and 12VDC DC JACK with 100 240VAC external power supply Field Wiring Terminal Use Copper Conductors Only 60 75 C wire range 12 24 AWG torque value 7 Ib in Operating temperature range 40 C to 75 40 F to 167 F Tested for functional operation 40 C to 85 C 40 F to 185 F UL508 Industrial Control Equipment certified Maximum Surrounding Air Temperature 75 C 167 F For use in Pollution Degree 2 Environment Supports Din Rail or Panel Mounting installation Ethernet Extender Mode Settings Ethernet Extender mode settings are made very simple by means of a switch at the top panel of the Ethernet Extender The sw
7. Port Status LEDs 455 5 AP INEZ User s Manual 10 100Base TX Hardened Ethernet Extender LEDs State Indication 1 Steady Power on Power2 Power3 Off Power off Ethernet Steady Valid network connection established Flashin Transmitting or receiving data Link ACT g ACT stands for ACTIVITY off Neither valid network connection established nor transmitting receiving data Connection in full duplex mode Steady FDX FDX stands for FULL DUPLEX Off Connection in half duplex mode Ethernet Extender Remote The device operates in remote mode Local The device operates in local mode Error Error occurred Link A valid connection established 1 Green 1 5Mbps up to 2 600M 8 530ft Amber 6 10Mbps up to 2 400M 7 874ft 2 Green 11 16Mbps up to 2 000M 6 561ft Amber 17 20Mbps up to 1 800M 5 905ft 3 Green 21 29Mbps up to 1 600M 5 249ft Amber 30 43Mbps up to 1 400M 4 593ft 4 Green 44 54Mbps up to 1 200M 3 937ft Amber 55 63Mbps up to 1 000M 3 280ft 5 Green 64 74Mbps up to 600M 1 968ft Amber 75 85Mbps up to 200M 656ft Functional Description Meets NEMA TS1 TS2 Environmental requirements temperature shock and vibration for traffic control equipment Meets EN61000 6 2 amp EN61000 6 4 EMC Generic Standard Immunity for industrial environment Complies with EN50121 3 2 EMC requirement
8. cesessscessssecessscessssesessssecsssecessesesesee 7 INTRODUCTION sosqsasssscessinscscssecasdasssecusoucodsaceasiatevesuthasacosacanteseatostossoasevsad 8 PRODUCT OVERVIEW PRODUCT FEATURES PACKING LIST ONE CHANNEL HARDENED ETHERNET EXTENDER PORTS ETHERNET EXTENDER MODE SETTINGS DIP SWITCH FRONT PANEL amp EEDS 2 IHRE INSTALLATION 12 SELECTING A SITE FOR THE EQUIPMENT DIN RAIL MOUNTING WiRING DIAGRAM CONNECTING TO POWER SPECIFICATIONS wsssisssscsossssscossssesesessstesessssssesossasvanssssoavsosssssebsssssoasebensses 15 User s Manual 10 100Base TX Hardened Ethernet Extender Introduction The Hardened Ethernet Extender provides one channel for Ethernet over existing coaxial cable This Hardened Ethernet Extender solution is perfectly fitted in the industrial applications or rugged environment Product Overview os Ov On E o Ew c of 1 S 1009 fi 21 o gt Product Features e Meets NEMA TS1 TS2 Environmental requirements temperature shock and vibration for traffic control equipment e Meets EN61000 6 2 amp EN61000 6 4 EMC Generic Standard Immunity for industrial environment e Complies with EN50121 3 2 EMC requirement e Operates transparent to higher layer protocols such as TCP IP e Ethernet port M12 connector Supports IEEE802 3 802 3u 8
9. hat the equipment receives adequate ventilation Do not block the ventilation holes of the equipment The power outlet should be within 1 8 meters of the product DIN Rail Mounting Fix the DIN rail attachment plate to the back panel of the Hardened Ethernet Extender Installation Place the Hardened Ethernet Extender on the DIN rail from above using the slot Push the front of the Hardened Ethernet Extender toward the mounting surface until it audibly snaps into place Removal Pull out the lower edge and then remove the Hardened Ethernet Extender from the DIN rail User s Manual 10 100Base TX Hardened Ethernet Extender Wiring Diagram Power 2 Power 3 Power 2 Power 3 Terminal Terminal Terminal Terminal Block Block Block 12 48VDC 12 48VDC M12 Connector Twisted Pair Copper Wire M12 Connector Twisted Pair Copper Wire BNC Connector Coaxial Cable Local Mode Remote Mode Connecting to Power Redundant DC Terminal Block Power Inputs or 12VDC DC Jack 12VDC DC Jack User s Manual 10 100Base TX Hardened Ethernet Extender Step 1 Connect the supplied AC to DC power adapter to the receptacle on the topside of the Hardened Ethernet Extender Step 2 Connect the power cord to the AC to DC power adapter and attach the plug into a standard AC outlet with the appropriate AC voltage Redundant DC Terminal Block Power Inputs There are two pairs of power inputs can be used to power
10. itch has two positions for Ethernet Extender mode settings Refer to the table below for more details One device must be set to Loc and the other to Rmt when two devices are connected Loc Rmt The device operates in local mode The device operates in remote mode Self diagnostic Test Procedure Two Hardened Ethernet Extenders are connected in pairs by BNC connectors over coaxial cable One Hardened Ethernet Extender is configured as local unit located at local site of Ethernet extension by setting mode switch at top panel of this Hardened Ethernet Extender to Loc local mode The other Hardened Ethernet Extender is configured as remote unit located at remote site of Ethernet extension by setting mode switch at top panel of this Hardened Ethernet Extender to Rmt remote mode Connect supplied power supplies to Terminal Block or DC Jack power input on top panel of these two Hardened Ethernet Extenders to power on these two Hardened Ethernet Extenders LED 5 on front panel of these two Hardened Ethernet Extenders might light on in amber or green color if these two Hardened Ethernet Extenders are connected in pairs by BNC connectors over a short coaxial cable less than 200 meters This means that these two Hardened User s Manual 10 100Base TX Hardened Ethernet Extender Ethernet Extenders could operate in normal condition since they finally negotiate a best performance for symmetrical transmission Assembly Start
11. up and Dismantling e Assembly Place the Hardened Ethernet Extender on the DIN rail from above using the slot Push the front of the Hardened Ethernet Extender toward the mounting surface until it audibly snaps into place e Startup Connect the supply voltage to start up the Hardened Ethernet Extender via the terminal block or DC JACK e Dismantling Pull out the lower edge and then remove the Hardened Ethernet Extender from the DIN rail a Lia User s Manual 10 100Base TX Hardened Ethernet Extender Preface This manual describes how to install and use the Hardened Ethernet Extender The Hardened Ethernet Extender introduced here provides one channel for Ethernet over existing coaxial cable The Hardened Ethernet Extender fully complies with IEEE802 3 10Base T and IEEE802 3u 100Base TX FX standards In this manual you will find Product overview e Features on the Hardened Ethernet Extender e Illustrative LED functions e Installation instructions e Specifications User s Manual 10 100Base TX Hardened Ethernet Extender Table of Contents QUICK START GUIDE 1 PHYSICAL DESCRIPTION 1 FUNCTIONAL DESCRIPTION 5 ETHERNET EXTENDER MODE SETTINGS SELF DIAGNOSTIC TEST PROCEDURE ASSEMBLY STARTUP AND 5 PREFACE RD 6 TABLE OF CONTENTS cssssssssessssessscesss
12. wer Adaptor and Power Cable optional User s Manual 10 100Base TX Hardened Ethernet Extender One Channel Hardened Ethernet Extender Ports The Hardened Ethernet Extender provides one TX port and one Ethernet Extender port For the TX port it uses M12 4Pin D type female connector and auto senses the speed of 10 100Mbps For the Ethernet Extender port it uses BNC connector and auto senses the speed of 1 5 10 20 30 40 50 60 70 75Mbps Ethernet Extender Mode Settings Ethernet Extender mode settings are made very simple by means of a DIP Dual Inline Package switch on the top panel of the Hardened Ethernet Extender DIP switch There is one pin on the DIP switch for Ethernet Extender mode settings Refer to the table below for more details Loc Rmt The device operates in local mode The device operates in remote mode User s Manual 10 100Base TX Hardened Ethernet Extender Front Panel amp LEDs LED Indicators The LED indicators give you instant feedback on status of the Hardened Ethernet Extender LEDs State Indication Power1 Steady Power on Power2 Power3 Off Power off Ethernet Steady valid Ethernet connection established Flashing Transmitting or receiving Ethernet data Link ACT 9 ACT stands for ACTIVITY Neither valid Ethernet connection established nor of transmitting receiving Ethernet data Stead Ethernet Connection in full duplex mode FDX Y

Manual

Contents

Download Pdf Manuals

Related Search

Related Contents