PD – 310 / 2604 Series User`s Manual
Contents
1. a PD 310 2604 Series PASEA User s Manual Rev Original FCC Notes This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions manual may cause interference to radio communications It has been tested an found to comply with limits for a Class A digital device pursuant to subpart J of Part 15 of FCC Rules which are designed to provide reasonable protection against interference when operated in a commercial environment Operation of this equipment in a residential area is likely to cause interference in which case the user at his own expense will be required to take whatever measures to correct the interference Warranty Limits Warranty terminates automatically when any person other than the authorized technicians opens the machine The user should consult his her dealer for the problem happened Warranty voids if the user does not follow the instructions in application of this merchandise The manufacturer is by no means responsible for any damage or hazard caused by improper application About This Manual Posiflex has made every effort for the accuracy of the content in this manual However Posiflex will assume no liability for any technical inaccuracies or editorial or other errors or omissions contained herein nor for direct indirect incidental consequential or otherwise damages including without limitation loss of data or profits resulting from the2. cFx Change RS mode ESC uF Top line scroll once ESC RS Direct to pole mode UTC Direct to pole mode EOT x Brightness DC4 Cursor off BS Back spacing CAN Clear to end of line HT Horizontal tab EM Clear to end of display LF Line feed SUB x Display fonts CR Carriage return ESC d Pass thru mode DLE Display position FS Flashing text start DC1 Normal display mode GS Flashing text end DC2 Vertical scroll mode RS Clear display DC3 Cursor on US Reset display INTERNATIONAL CHARACTER SETS FOR PD 2604 Hex code Country Hex code Country 0 USA 6 Italy 1 France 7 Spain 2 Germany 8 Japan 3 United Kingdom 9 Norway 4 Denmark I A Denmark II 5 Sweden B Ex Jugoslavia POSIFLEX Part 10
3. ex com tw Download 20list asp Status 1 amp Series_Name U POS amp Model_Name OPOS and execute the file SETUP EXE to install the Part 5 OPOS Control Manager To add the customer display under OPOS control please set in OPOS Control Manager device name PD3x Line Display in the top row For RS 232 models select the COM port in the 3 row and set baud rate to 9600 in 4 row as in the left sample screen below Select USB in 3 row for USB interface models as in the right sample picture below EE Posiflex OPOS Control Manager v 1 3 2 6 EE Posiflex OPOS Control Manager v 1 3 2 6 PD3rLine Dispald LD Dermo use Engisha7 v M use cco SPECIFICATION OPTICAL Number of digits 20 digits row 2 rows Dot matrix 5 X 7 dots Digit height 9 66 mm PD 310 9 03 mm PD 2604 Digit width 6 0 mm PD 310 5 25 mm PD 2604 Display color Dark blue PD 310 Green PD 2604 MECHANICAL Display Head Height 57 5 mm Display Head Width 196 6 mm Display Head Depth 39 5 mm Case color Black ELECTRICAL Power from interface port of KS system 5VDC 1A ENVIRONMENTAL Operating temperature 0 to 40 C Storage temperature 10 to 60 C Operating humidity 20 to 85 non condensing Storage humidity 5 to 90 non condensing WARNING If the user opens the pole display housing to make any modification all the prod
4. furnishing performance or use of this material This information is provided as is and Posiflex Technologies Inc expressly disclaims any warranties expressed implied or statutory including without limitation implied warranties of merchantability or fitness for particular purpose good title and against infringement The information in this manual contains only essential hardware concerns for general user and is subject to change without notice Posiflex reserves the right to alter product designs layouts or drivers without notification The system integrator shall provide applicative notices and arrangement for special options utilizing this product The user may find the most up to date information of the hardware from web sites http www posiflex com or http www posiflex com tw All data should be backed up prior to the installation of any drive unit or storage peripheral Posiflex will not be responsible for any loss of data resulting from the use disuse or misuse of this or any other Posiflex product All rights are strictly reserved No part of this documentation may be reproduced stored in a retrieval system or transmitted in any form or by any means electronic mechanical photocopying or otherwise without prior express written consent from Posiflex Technologies Inc the publisher of this documentation Copyright Posiflex Technologies Inc 2008 All brand and product names and trademarks are the property of their re
5. g Cursor A A Invisible Block Block Default mode sA A Over W V scroll Over W PT 2 chars User defined font A 2 chars N A 2 chars PT Brightness control YES YES YES YES DP Leading code change NO YES YES YES PT Code page select YES YES YES YES Auto scroll message NO YES YES YES PT Timer clock YES NO NO YES PT For PD 310 it is always the Epson command mode at power on It can enter or exit the PST command mode through software command DRIVER INSTALLATION FOR RS 232 INTERFACE MODELS For direct I O control over the serial interface RS232 models you have to send all commands listed later in this manual under communication protocol 9600 bps none parity 8 data bits 1 stop bit with hardware handshaking on CTS signal to the COM port used No other driver installation is required FOR USB INTERFACE MODELS Copy the driver and library from Posiflex Product Information CD or DVD under Drivers PD23_26U to your system or download from web site http www posiflex com tw Download 20list asp Status 1 amp Series_Name P D 20Series amp Model_Name PD 2300U Follow instructions given in the file README TXT to send commands listed later in this manual and data to the customer display under the programming language FOR OPOS APPLICATION Find the subfolder Drivers UPOS OPOS of the Posiflex Product Information CD or DVD or download it from web site http www posifl
6. lt 06 gt lt N gt lt N2 gt Change Leading Code lt 14 gt lt 01 gt Wraparound Mode Default lt 14 gt lt 02 gt Vertical Scroll Mode lt 14 gt lt 03 gt Part 7 A gt O V BS HT LF HOM CLR CR ESC lt 1B gt lt 3D gt lt n gt The Euro Dollar Sign is designated at code lt D5 gt h COMMAND CODES SUMMARY FOR PD 2604 Command Function Command Function ADM mode 0C Clear Display 10 Write Decimal Point OD Carriage Return IE Write Field 1 OE Write Line 1 IF Write Field 2 OF Write Line 2 AEDEX mode Attention code Function code data CR 1 Display top 7 Stop trapping 2 Display bottom 8 Change attention code 4 On going scroll 9 Display whole area 6 One time scroll EPSON mode BS Move cursor left US Mark semicolon HT Move cursor right US lt Clear mark LF Move cursor down USE Set cancel blinking HOM Move cursor home UST Set and display counter CLR Clear display screen US X Brightness adjustment Part 8 7 a CR Move cursor left ESC Set cancel user defined most char CAN Clear cursor line ESC amp peti user detined US MD1 Overwrite mode ESC aoe MECANO US MD2 Vertical scroll mode US Show firmware version US MD3 Horizontal scroll ESC Select peripheral mode device US LF Move cursor up ESC t Select code
7. ode is set to Noritake mode for normal delivery Please change it to Epson mode if OPOS or UPOS driver is used for the application program POWER ON SIGN With interface cable connection well installed and with COM port power set for serial models turn on the KS Posiflex POS system a firmware identifier as power on sign will appear on the pole display screen for a while to indicate that pole display is self tested O K and ready to work USING THE CUSTOMER DISPLAY INTERRFACE SELECTION This series of customer display is designed to serve in KS series Posiflex POS systems with RS232 interface models and with USB interface models It is advisable to well study the I O port availability of the host system before determining which interface model to be used In case the RS232 interface PD 310 2604 is to be removed from the KS system consequently the jumper has to be changed back to neutralize the COM port power support otherwise damage could occur Part 4 a The USB interface model of PD 310 2604 should be connected directly to an USB port and must not be through any non self powered USB HUB to get power through the USB port itself and there is no need for other special arrangement COMMAND MODE SELECTION GUIDE The below table provides some comparison for selection on command mode to be used in the application program for PD 2604 if it is not yet determined Epson Futaba Noritake Blinking Block DP Blinking Blinkin
8. oulder screws Slide down the TETE kit and gently tighten the shoulder screws Do not overdo the tightening or unrecoverable thread damage will occur Remember to disable the 5 V DC supply in the COM port of the main unit if the upgrade kit is no longer to be used otherwise any damage or loss caused consequently shall be out of product warranty However if the customer display used is the USB interface model the DC supply in COM port is not required it will be powered through the USB port Part 3 a COMMAND EMULATION MODE SETUP FOR PD 2604 Now please check the back of PD 2604 display head as in the left picture below There is a small piece of plastic cover for the DIP switch window Slide the cover downward but don t pull it off otherwise you may have to practice for inserting it back You can find 6 positions of DIP switches in this window Adjust for the appropriate command mode used by the application program according to below table Switch position counts from left to right and ON means pushed up as indicated in the right part picture below DIP switch F window Seach Positin z Command Mode ON OFF OFF ON OFF OFF ADM ON OFF ON ON OFF OFF Aedex ON OFF ON OFF OFF OFF Epson ON OFF OFF ON ON OFF Futaba ON OFF ON OFF ON OFF Noritake ON OFF ON ON ON OFF UTC The factory default command m
9. page table US CR Move curser rent US B Move cursor to bottom most z Move cursor oa US D ESC Initialize display US Mark comina ESC R VOA character US Mark period US U Display counter FUTABA mode IF Reset 10 pp Digit select 04 bb Brightness control 13 Cursor on LE pp Change code page 14 Cursor off IC Oi ore raarpnal 08 Back space character set 05 0D Moving sign 11 09 Horizontal tab 06 x1 x2 Change leading code 2 09 Vertical scroll up 0l Set pass through flag 71 0A Cursor up down x1 x2 02 Ta pass thiongh ya ga Line feed OD Carriage return NORIRAKE mode 1B 49 Reset 1B 54nn Cursor blinking Rate OE Clear 15 Cursor on 1B 4C bb Brightness control 16 Cursor off 1E pp Change code page 08 Back space IC Oi ajeran gnal 1109 Horizontal tab character set 05 0D Moving sign 12 09 Vertical scroll up 06 x1 x2 Change leading code 77 0A Cursor up down 0l Set pass through flag 12 0A Line feed Part 9 Clear pass through x1 x2 02 flag 0C Form feed IB 48 pp Digit select 0D Carriage return ee eee User defined fonts UTC Pass through mode Command data CR ESC uA Top line message ESC uH Redefine graphic ESC uA CR Clear top line ESC ulx __ Display fonts ESC uB CR Clear bottom line ESC uE Set Display time ESC uB Bottom line message ESC utcEx Change d mode ESC uD Continuous scrolling ESC ut
10. qualified electronic technician following guide from relevant technical manual The default communication protocol should be set to 9600 bps none parity 8 data bits 1 stop bit with hardware handshaking on CTS The power for the USB interface type pole display is supported through the USB connection However should these customer displays are to be connected through an USB HUB instead of a direct USB port of the system the HUB must be powered by a separate power adaptor otherwise there could be the power shortage problem INSTALLATION To mount the rear top mount upgrade kit like PD 310 or PD 2604 on the back of KS series please apply carefully the 2 small fixation shoulder screws that come along with PD 310 or PD 2604 to the back of KS series at the screw hole triangle marked in the 2 upper right pictures However please do not screw them to the bottom but at a position that is about 1 turn loose from the bottom Similarly please loosen the screws by 1 turn for some KS models with these 2 screws preinstalled Arrange the interface cable of the rear top mount upgrade kit to go into the first groove to the right of the left shoulder screw on back of main unit as in the lower picture at right For host models with gen 6 super slim base please stick the 2 attached cable clips at arrowed positions of gen 6 base in the picture for cable routing when later joining the main unit to gen 6 base Hook the rear bracket of the upgrade kit onto the sh
11. spective holders P N 19430901010 Part 1 a BRIEF INTRODUCTION THE PRODUCT The PD 310 PD 2604 is a rear top mount customer display option designed for Posiflex KS 6215 Plus or KS 661X or KS 731X series POS terminals It is delivered in separate carton for KS series and shall be installed per instructions in this manual FEATURES LCD Liquid crystal display with dark blue character and yellow green back light for PD 310 Bright VFD vacuum fluorescent display with green filter for PD 2604 Two line display with 20 characters per line Easy viewing characters 6 0 mm by 9 66 mm for PD 310 9 03 mm by 5 25 mm for PD 2604 Long life and trouble free operation Simple installation Selectable between Serial RS232 interface model and USB interface model Selectable command emulation modes including PST and EPSON command emulation modes for PD 310 Various command emulation modes selectable by DIP switch for PD 2604 Support 13 Code Pages of 128 characters each for PD 2604 Support 12 international character sets of 12 characters each for PD 2604 Supports UPOS 1 8 and is WEPOS ready for PD 2604 Part 2 INSTALLATION GUIDES HOST SYSTEM PREPARAION For serial interface RS232 PD 310 or PD 2604 to be used in KS series you have to adjust during power off the internal jumper of the host system to supply 5 V DC to the COM port selected for the serial interface pole display This adjustment has to be done by a
12. uct warranty will be voided NOTE Please refer to Posiflex Product Information CD or DVD or visit our web http www posiflex com tw for further information when needed Part 6 a APPENDIX APPLICABLE COMMANDS FOR PD 310 EPSON COMMAND MODE POWER ON DEFAULT NAME FUNCTION Move Cursor Left lt 09 gt Move Cursor Right Move Cursor Down Move Cursor To Home Position Clear Display Screen Move Cursor To Left Most Position CAN Clear Cursor Line Select Peripheral Device Command Mode n pass through should not be used n 2 3 not required n 4 switch to PST command mode ESC lt 1B gt lt 40 gt Initialize Display ESCt lt 1B gt lt 74 gt lt n gt Disable Enable Euro Dollar Sign n 0 19 US MD1 lt 1F gt lt 01 gt ecify Overwrite Mode US MD2 lt 1F gt lt 02 gt P lt 1F gt lt 02 gt Specify Vertical Scroll Mode US MD3 lt 1F gt lt 03 gt p ecify Horizontal Scroll Mode US LF lt IF gt lt 0A gt ove Cursor Up US CR lt IF gt lt 0D gt ove Cursor To Right Most Position Move Cursor To Specified Position US lt 1F gt lt 24 gt lt n gt lt n 1 20 m gt m 1 2 US lt lF gt lt 40 gt Show Version USB lt lF gt lt 42 gt Move Cursor To Bottom Position USC lt lF gt lt 43 gt lt n gt Cursor On Off n 1 0 Blink Display Screen USE lt IF gt lt 45 gt lt n gt n 0 255 PST COMMAND MODE HEX CODES FUNCTION lt 01 gt Set Pass Through Flag should not be used
Download Pdf Manuals
Related Search