Pressure Reference Type P USER MANUAL
Contents
1. If kept pressed for 2 sec during the measurement it activates the PEAK function which allows the display of the Highest pressure measured after the activation of the function If kept pressed for 4 sec during the measurement it activates the PEAK function which allows the display of the Lowest pressure measured after the activation of the function In the setting menu it increases A the values of a given parameter Pressed for 6 sec it displays the temperature in C to come back to pressure press the same key again Note only for model 0 5 PGE and model 0 2 Bit02B If kept pressed for 5 sec during the measurement it switches off the manometer in manual mode OFF Note only for model 0 05 LabDMM SIKA Dr Siebert amp K hn GmbH amp Co KG Struthweg 7 9 34260 Kaufungen Germany 8 17 49 5605 803 0 amp 49 5605 803 54 info SIKA net www SIKA net SETTING MENU To enter into the setting menu keep pressed the SET key for approx 3 seconds until the first parameter appears on the display Press SET to move to next parameter and then to exit from the setting menu After the last parameter the SET key saves the parameters then comes back to the measurement mode Unit FL XX r XX OFFXX bAUdX SIKA Dr Siebert amp K hn GmbH amp Co KG Struthweg 7 9 34260 Kaufungen Germany MEASUREMENT UNIT In this step it is possible to change the measurement2. 21755 2000 20000 250 BEEN O 200 00 29007 LL y O SIKA Dr Siebert amp K hn GmbH amp Co KG Struthweg 7 9 34260 Kaufungen Germany 5 17 49 5605 803 0 49 5605 803 54 54 info 9 SIKA net www SIKA net Model 0 2 Bit02B 4 digit Model 0 5 PGE 4 digit Nominal Pressure Pressure unit digits after decimal point bar 1 2 5 5 RECOMMENDED MECHANICAL MOUNTING Z WARNING N During the gauge mounting DO NOT force the case but tight with the wrench O RING tight USIT RING Double cone tight for pressures 12 70X18X1 5 for pressures lt 1000bar for pressures gt 1000bar lt 1000bar SIKA Dr Siebert amp K hn GmbH amp Co KG Struthweg 7 9 34260 Kaufungen Germany 49 5605 803 0 49 5605 803 54 54 info 9 SIKA net www SIKA net 6 17 INSTALLATION Installation shall be done by authorized personnel only for a fast installation follows the instructions listed below a PRELIMINARY CHECKS b Instrument POWER ON and control of display functioning during the TEST phase c PROGRAMMING measurement unit digital filter etc a PRELIMINARY CHECK Be sure that pressure provided is not higher than the instrument full scale Mount the manometer as suggested If the manometer is installed in a oil pressure circuit please perform the bleeding before starting to work b INSTRUMENT POWER ON A
3. 34260 Kaufungen Germany 49 5605 803 0 49 5605 803 54 PC HOST info SIKA net www SIKA net 10 17 COMMUNICATION PROTOCOL optional The communication protocol is 8 bit data 1 bit stop NO parity CTS RTS DCD are not handled Command Strings Format and parameters programming p n XX cr p the parameter strings starts with this character n parameter number from 1 up to 8 XX decimal value to be assigned to the parameter cr Carriage Return 13 1 MEASUREMENT UNIT pixxcr 00 psi 01 MPa 02 kPa 03 bar 04 mbar 2 DIGITAL FILTER p2xxcr xx values from 00 up to 99 3 RESOLUTION p3xxcr 00 1 Di 2 02 5 03 10 4 AUTO POWER OFF TIME p4xxcr xx values from 01 up to 30 minutes 5 BAUD RATE p5xxcr 00 OFF 01 4800 02 9600 03 19200 OFF disables the serial output 6 ZERO p6xxcr 00 ZERO OFF 01 ZERO ON 7 POSITIVE PEAK p7xxcr 00 PEAK OFF 01 PEAK ON 8 NEGATIVE PEAK p8xxcr 00 PEAK OFF 01 PEAK ON To read the manometer pressure send the following string p 0 00 cr The answer will be the following string s XX XXX um z py LB cr s sign ASCII character or XX XXX measurement value with decimal point um measurement unit from 00 up to 04 Z
4. pressure confirm the pressure setting with the SET key Adjust the reading by using the Aand Wkeys confirm with the SET ke Bring the manometer to 10096 F S of the pressure confirm the pressure setting with the SET key Adjust the reading by using the A and V keys confirm with the SET key To complete the adjustment of the positive measuring range confirm with the SET key without performing any correction on point P6 Note only available at model 0 05 LabDMM Negative Full Scale adjustment procedure Bring the manometer to 1 bar and confirm with the SET key Adjust the reading with the A and W keys confirm with the SET key In this phase the decimal point has to be set Confirm with the SET key move the decimal point using the A and V keys confirm with the SET key Dr Siebert amp K hn GmbH amp Co KG Struthweg 7 9 34260 Kaufungen Germany 49 5605 803 0 49 5605 803 54 54 info 9 SIKA net www SIKA net 14 17 Positive full scale adjustment for model 0 5 PGE and modell 0 2 Bit02B Switch on the manometer ON and keep the SET and PEAK keys pressed together during the TEST phase Set the password 2124 using the A and V keys confirm with the SET key Set at 1 if the full scale to be programmed does not exceed 65000 div Set at 2 if the full scale to be programmed exceeds 65000 div Note Since the manometer is supplied calibrated adjustment of this parameter is not necessary Vary
5. the manometer readings on return to zero SIKA holds the right to make any change when necessary without notice The data contained in this manual are just indicative and the manufacturer declines any responsibility for errors or discrepancies with respect to this manual SIKA Dr Siebert amp K hn GmbH amp Co KG Struthweg 7 9 34260 Kaufungen Germany 17 17 49 5605 803 0 49 5605 803 54 54 info 9 SIKA net www SIKA net
6. unit through the keys V and A DIGITAL FILTER In this step the operator can change the Digital Filter effect By increasing the XX value the filter effect increases Enabling the operator to detect the average value of unsteady or pulsating pressures Selectable values go from 0 up to 99 This function also acts on display conversion speed therefore if peaks shall be detected it is recommendable to decrease the filter effect at its minimum RESOLUTION In this step it is possible to set the Resolution used by the manometer to display the pressure Selectable values 1 2 5 and 10 TIME OF AUTO POWER OFF This parameter defines the time in minutes from 1 up to 30 before the auto power off activates in case of constant pressure The auto power off time starts working if the manometer does not detect pressure changes higher than 10 RS232 BAUD RATE option In this step it is possible to program the transmission speed of RS232C serial output Selectable values are 124800 229600 3219200 0 RS232 disabled Note We recomend to disable of the RS232 if it is not used Baud rate 0 49 5605 803 0 49 5605 803 54 info SIKA net www SIKA net 9 17 RS232C CONNECTION option Canon 9 pin SUB D female Model A B Pin 1 DCD Pin 2 RX Pin 3 9 TX Pin 5 GND SIKA Dr Siebert amp K hn GmbH amp Co KG Struthweg 7 9
7. with the A and V keys confirm with the SET key Bring the manometer to 0 bar by opening the pressure circuit confirm the pressure setting with the SET key If the manometer displays an offset then make a reset by using the ZERO key confirm with the SET key Bring the manometer to 0 2 bar 2096 F S confirm the pressure setting with the SET key Adjust the reading by using the A and V keys confirm with the SET key Bring the manometer to 0 4 bar 4096 F S confirm the pressure setting with the SET key Adjust the reading by using the A and V keys confirm with the SET key Bring the manometer to 0 6 bar 6096 F S confirm the pressure setting with the SET key Adjust the reading by using the A and V keys confirm with the SET key Bring the manometer to 0 8 bar 8096 F S confirm the pressure setting with the SET key Adjust the reading by using the Aand Wkeys confirm with the SET key Bring the manometer to 1 bar 10096 F S confirm the pressure setting with the SET key Adjust the reading by using the A and keys confirm with the SET key In this phase the decimal point has to be set Confirm with the SET key move the decimal point using the A and V keys confirm with the SET key SIKA Dr Siebert amp K hn GmbH amp Co KG Struthweg 7 9 34260 Kaufungen Germany 49 5605 803 0 49 5605 803 54 54 info 9 SIKA net www SIKA net 15 17 ERROR MESSAGES UUUU Positive Overload the manometer is
8. SIKA Pressure Reference Type P Model 0 5 PGE Model 0 2 Bit02B Model 0 05 LabDMM USER MANUAL SIKA Dr Siebert amp K hn GmbH amp Co KG Struthweg 7 9 34260 Kaufungen Germany 1 17 49 5605 803 0 49 5605 803 54 X info 9 SIKA net www SIKA net V05 2014 09 GENERAL INDEX INTRODUCTION TECHNICAL DATA STANDARD FULL SCALE and RESOLUTION RECOMMENDED MECHANICAL MOUNTING INSTALLATION GENERAL KEYS DESCRIPTION SETTING MENU RS232C CONNECTIONS COMMUNICATION PROTOCOL BATTERY REPLACEMENT DISPOSAL OPTIONS DIMENSIONS FULL SCALE CALIBRATION ERROR MESSAGES SIKA has the right to make any change when necessary without notice Data enclosed in this manual are just indicative and the manufacturer declines any responsibility for errors or discrepancies contained in this manual SIKA Dr Siebert amp K hn GmbH amp Co KG Struthweg 7 9 34260 Kaufungen Germany 49 5605 803 0 amp 49 5605 803 54 info SIKA net www SIKA net 2 17 INTRODUCTION The digital gauges are made according to the more modern technologies in order to assure an high level of reliability versatility and inexpensiveness at the same time Its main applications develop in industrial fields where it is necessary to check processes or in field with a precision class better than up to 0 05 To increase th
9. ax F S from 1 to 60 Bar panal mounting version DIMENSIONS mm 45 5 RS232C CN A 100 t t t Sei gauge for Standard case dimensions Built in case a SIKA Dr Siebert amp K hn GmbH amp Co KG Struthweg 7 9 34260 Kaufungen Germany 12 7 49 5605 803 0 amp 49 5605 803 54 info SIKA net www SIKA net FULL SCALE ADJUSTABLE Z WARNING N This procedure is described in the manual by way of documentation only but it shall be performed by authorised calibration centres only and in case of real need SIKA declines any responsibility for measurement errors or bad functioning which should be caused by adjustment performed not properly In this case the validity of manometer certification would lose The adjustment procedure allows correction of up to 30 of the F S Note the full scale adjustment shall be performed with the measurement unit programmed in bar The full scale is adjusted through a procedure of calibration by points which also allows linearisation of the pressure sensor On the positive scale pressure reading the manometer has to autolearn all the points P0 0 P1 20 P2 40 P3 60 P4 80 P5 100 of the full scale On the negative scale vacuum readings the manometer has to autolearn only point P6 at 1bar the negative scale is an optional feature Example Reference P having a pressure range from 1 5 bar SIKA Dr Sie
10. bert amp K hn GmbH amp Co KG Struthweg 7 9 34260 Kaufungen Germany 13 7 49 5605 803 0 49 5605 803 54 54 info 9 SIKA net www SIKA net 8 8 8 8 8 P0000 SIKA Positive full scale adjustment Switch on the manometer ON and keep the SET and PEAK keys pressed together during the TEST phase Set the password 3124 using the A and V keys confirm with the SET key Set at 1 if the full scale to be programmed does not exceed 65000 div Set at 2 if the full scale to be programmed exceeds 65000 div Note Since the manometer is supplied calibrated adjustment of this parameter is not necessary Vary with the A and V keys confirm with the SET key Bring the manometer to 0 bar by opening the pressure circuit confirm the pressure setting with the SET key If the manometer displays an offset then make a reset by using the ZERO key confirm with the SET key Bring the manometer to 2096 F S of the pressure confirm the pressure setting with the SET key Adjust the reading by using the A and V keys confirm with the SET key Bring the manometer to 4096 F S of the pressure confirm the pressure setting with the SET key Adjust the reading by using the A and V keys confirm with the SET ke Bring the manometer to 6096 F S of the pressure confirm the pressure setting with the SET key Adjust the reading by using the A and keys confirm with the SET ke Bring the manometer to 8096 F S of the
11. cludes a pressure bar analog indication always active also inside the programming menu Main characteristics 1 YEAR AUTONOMY WITHOUT RECHARGE PROGRAMMABLE RESOLUTION PROGRAMMABLE DIGITAL FILTER ZERO FUNCTION PEAK FUNCTION positive and negative Temperature display model 0 5 PGE model 0 2 Bit02B PROGRAMMABLE BAUD RATE option RS232C SERIAL OUTPUT option SIKA Dr Siebert amp K hn GmbH amp Co KG Struthweg 7 9 34260 Kaufungen Germany 3 17 49 5605 803 0 49 5605 803 54 54 info 9 SIKA net www SIKA net TECHNICAL DATA LabDMM Bit02B PGE RELATIVE PRESSURE R 1 2 5 5 10 20 40 50 60 bar 100 250 350 500 bar 700 1000 1500 2000 2500 bar HYSTERESIS TEMPERATURE indication a Resolution 0 1 C b accuracy lt 1 CT TEMPERATURE EFFECT per 1 C a on zero lt 0 002 b on sensitivity lt 0 002 POWER SUPPLY Battery BATTERY AUTONOMY 1 year 1 YEAR ALKALINE BATTERIES Ax 1 5V AAA 2x 1 5V AAA 65 000 divs 65000dvs 1 O PROG MEASURE UNITS mbar bar MPa kPa psi PROGRAMM RESOLUTION 1 2 5 10 PROGRAMM BAUD RATE 19200 9600 4800 ZERO FUNCTION 5096 F S PEAK FUNCTION positive and negative READINGS PER SEC 10 Sampling rate 100 msec DISPLAY 16 mm custom LCD MECHANICAL LIMIT VALUES 8 service pressure 100 F S b max permissible pressure 15096 F S C breaking pressure gt 300 F S d high
12. e practicality and make the instrument completely autonomous the pressure gauge is fed by internal batteries which ensure round 1 year In the programming menu reachable through the keyboard it is possible to adjust different functions such as e AUTO POWER OFF function which activates if within 30 minutes any pressure variations is detected e digital filter that allows to maintain the measurement steady even in presence of unsteady pressures e the display resolution which allows to increase the measurement at fixed steps 2 5 10 and e the measurement unit which can be changed into mbar bar kPa MPa and psi The sensor entirely executed in stainless steel is monolithic to ensure a long term high stability even in presence of highly dynamic pressures By selecting the reading of the TEMPERATURE model 0 5 PGE and model 0 2 Bit02B you can see on display the temperature of the fluid that is in contact with the pressure sensor The new generation of digital manometers consist of a long term particularly steady analog section and of A D 16 bit converter which guarantees a max of 65000 internal divisions The various versions are proposed for the different applications such as instruments for metrological laboratories to be used as first or second line samples for industrial applications for data monitoring and transmission for processes control or for testing material equipment presses test benches etc The LCD display in
13. if z is present the it indicates that ZERO function is active py if in these two positions the optional chars p or p appear it means that peak function is active and precisely p positive peak p negative peak LB If present indicates a low battery condition SIKA Dr Siebert amp K hn GmbH amp Co KG Struthweg 7 9 34260 Kaufungen Germany 11 17 2 49 5605 803 0 amp 49 5605 803 54 info SIKA net www SIKA net BATTERY REPLACEMENT The instrument is supplied with 2 model 05 PGE and model 0 2 Bit02B or 4 model 0 05 LabDMM not rechargeable Alkaline batteries AAA type 1 5V with an average autonomy of 1 year Batteries consumption is signaled by the LO BAT icon the measurements performed during this phase could be altered replace therefore the batteries During this operation clean up the clips contacts from possible oxydation and check the pressure exerted by external flaps on each battery please increase it if necessary Verify the electrical contact also in presence of malfunctions ALKALINE battery pack must be recycled or disposed properly WARNING If the instrument won t be used for long time it is suggested to N REMOVE batteries from manometer DISPOSAL Delivery the instrument to company specialised in scrapping according to the laws in force in the countries where the instrument is commercialised OPTIONS SERIAL OUTPUT RS232C STANDARD SERIAL CABLE VACUUM OPTION m
14. ly dynamic pressure 7596 F S REFERENCE TEMPERATURE 23 C SERVICE TEMPERATURE 0 50 C 10 70 C on request STORAGE TEMPERATURE 10 60 C 10 80 C on request PROCESS COUPLING 1 2 BSP MALE TIGHTENING WRENCH 27 mm TIGHTENING TORQUE 28 Nm PROTECTION CLASS EN 60529 IP40 IP65 front panel SENSOR EXECUTION INOX 17 4 PH CASE EXECUTION Aluminium OPTIONALS SSS Aluminium IP65 front SERIAL OUTPUT RS232C SUB D 9 pole FEMALE VACUUM V range 1 21 1 2 5 1 5 bar 71 410 1 20 1 40 bar 1 450 1 60 bar SIKA Dr Siebert amp K hn GmbH amp Co KG Struthweg 7 9 34260 Kaufungen Germany 4 17 49 5605 803 0 amp 49 5605 803 54 info SIKA net www SIKA net STANDARD FULL SCALE and RESOLUTION Model 0 05 LabDMM Model 0 2 Bit02B Model 0 5 PGE Nominal Pressure Pressure Resol Vacuum Pressure Resol Vacuum ENGINEERING UNITS Model 0 05 LabDMM 5 digit Pressure unit digits after decimal point PSI 14 503 36 259 72 518 145 03 290 07 580 15 725 19 60 1 1 60 000 60000 6000 0 6 0000 870 23 100 10000 10000 10 000 14504 1250 1 25000 25000 25000 36259 350 235000 35000 35000 5076 3 500 150000 50000 50 000 7251 9 700 70000 70000 70 000 10152 1000 10000 14503 1500 15000
15. measuring a pressure higher than its nominal rate LLLL Negative Overload the manometer is measuring a vacuum higher than 1 bar Warning if an overload occurs check if calibration has been altered HHHH Out of the Scale the instrument shows the overflow of display physical limit 9999 or 99999 LbAt Low Battery batteries level is low Please change batteries You need to use the cone In the picture above on a hole of about 6 7 with sharp edge place on the same axis of the transducers hole i e of 77 the fillet CONO MORDENTE DOUBLE FERRULE SEAL SIKA Dr Siebert amp K hn GmbH amp Co KG Struthweg 7 9 34260 Kaufungen Germany 16 17 49 5605 803 0 49 5605 803 54 54 info 9 SIKA net www SIKA net RECOMMENDED CALIBRATION ROCEDURE a Carry out three cycles to the Full Scale of the manometer for checking preloading cycles b Take the zero measurements at atmospheric pressure with the discharge valve open c Generate the pressure taking the sample manometer as reference and take the two readings simultaneously d Record the measurements at increasing pressures e g 5 points to evaluate the linearity and reading errors e Record the measurements at decreasing pressures e g 5 points to evaluate the hysteresis errors Discharge the system by opening the discharge valve and take
16. t power on the instruments execute a display test cycle Verify the lighting of display with software release indication 3 secs After this test it s displayed the input pressure Ifa LLLL lower limit reached or a UUUU message are displayed it s recommended to conduce immediately the pressure into the correct range c PROGRAMMING Functions and parameters are grouped in this SETTING MENU Measurement unit Digital Filter Resolution Power Off Time Baud Rate OO E ob ch ree Ee TE E SIKA Dr Siebert amp K hn GmbH amp Co KG Struthweg 7 9 34260 Kaufungen Germany 49 5605 803 0 amp 49 5605 803 54 info SIKA net www SIKA net 7 17 ON OFF SET ZERO on ZERO off down PEAK PEAK up OFF KEYS GENERAL DESCRIPTION Pressed for 5 sec it performs the manual switching off of the pressure gauge Note only for model 0 5 PGE and model 0 2 Bit02B to enter into the setting menu keep it pressed for about 3 seconds to switch on the manometer ENEMIES 11 If kept pressed for 3 sec during the measurement it performs the ZERO of the display in the first 5096 of manometer range ZERO does not have any effect on graphic bar indication of the pressure If kept pressed for 6 seconds it deactivates the ZERO function by showing the manometer offset Inside the setting menu it allows the operator to decrease V the values of defined step
Download Pdf Manuals
Related Search