h1000 pilot
Contents
1. 0 1Nm and allow the boat to settle Activate the Pilot in Nav Mode by pressing the ON key once When engaged in Nav Mode the Pilot will steer a course that aims to keep the cross track error toa minimum and will allow the boat to safely arrive at the next waypoint automatic waypoint advance Many position fixers will automatically switch to the next waypoint in a sail plan For reasons of Safety however the 1000 Pilot will not automatically steer to the next waypoint until instructed by the user If the position fixer is transmitting valid waypoint route information and automatically switches to the next waypoint in a route the Pilot will prompt the user with the message Next Waypoint When it is safe to do so press the ENTER key within four seconds to instruct the Pilot to start navigating to the next waypoint in the route additional navigate mode pages With the pilot ON pressing the UP DOWN keys will scroll the display to a second and third Nav Mode page Page 2 displays navigation information relative to the selected Waypoint Page 3 displays a track screen of the current data A circle on the screen indicates the active waypoint h1000 pilot Main Menu Tack Memories Timer Calibration Fage Contents System Main Menu Memories ML Timer Calipratio Page Cont System after delay Main Menu Tack Memories Timer Calibration Fage Contents System Memories Pilot Compass Fesettrip log Alarms2. Disengages the Pilot compass mode Page 6 h1000 pilot OM Comp Mode Heading Set CRES 262 264 pilot mode selection compass mode With Compass Mode selected and the Pilot switched OFF steer the boat onto the desired heading and allow the boat to settle Engage the Pilot in Compass Mode by pressing the ON key once The display changes to Heading and Set CRS Course A rudder position indicator bar is also displayed at the bottom of the screen Course changes can now be made by turning the rotary knob or by pressing the 10 and 10 increment keys dodging Press the 10 key or turn the rotary knob anti clockwise to alter course to port in 10 or 1 increments Press the 10 key or turn the rotary knob clockwise to alter course to starboard in 10 or 1 increments Multiple presses of the keys are added together to give the required course change e g for 20 to port press 10 twice for 11 to starboard press 10 then one click of the rotary knob clockwise Alternatively the rotary knob can be used exclusively to dodge around objects The previous autopilot course is automatically stored in memory Press the ON key twice within four seconds to resume the previous course memorising the new course Press and hold the ON key for two seconds to update and store the new course in the autopilot course memory It is suggested that this be carried out after every permanent course
3. autopilot drive units which are subject to 12 months warranty It is the users responsibility to demonstrate the date of purchase by showing a valid warranty card or proof of purchase If the user cannot do this the date of purchase shall be deemed to be the date of manufacture as evidenced by the serial number of the product 3 repair and replacement During the Warranty period and subject to the terms and conditions set out below B amp G will repair or if it so chooses replace the product It is the user s responsibility to arrange and pay for transport of the product to the nearest authorized B amp G representative and any re installation required following repair B amp G shall not be responsible for any such costs including but not limited to 3 1 Boat slipping or lifting 3 2 Freight shipping charge 3 3 Engineer s travelling time and expenses 3 4 Installation labour costs associated with the Warranty claims and 3 5 Loss or damage of products or boats in transit 4 conditions The Warranty will not apply in the following circumstances 4 1 Where the product has been installed in a manner or location other than that specified in the installation instructions 4 2 Where the product has been serviced or repaired by anyone other than an authorized representative 4 3 Where the product has been used for purposes for which it is not intended 4 4 Where the product has been used in a manner other than that described in
4. default setting is 10 seconds TWA mode see also Page 9 of this manual Pressing the ENTER key displays the status for TWA mode Selecting ON configures the Pilot to use TWA information when steering in Wind Mode This function is particularly useful for optimising downwind steering performance Speed source The speed source option allows the source for speed data to be selected Pressing the ENTER key displays the three options available paddle SOG from a GPS and manual Pressing the UP DOWN key toggles between the options Selecting the manual option activates a further screen which allows adjustment of the three manual speed settings slow medium and fast Alter these settings to the most appropriate values for the particular boat h1000 pilot main menu memories menu Compass The compass memory allows a pre set heading to be defined and any deviation from that course will be shown as an error on the Tactical Compass page This course can be updated by one of three methods The first method is simply by pressing the ENTER key whilst the display is showing the Tactical Compass page The second is by using the drop down box in the Memories gt Compass Course drop down menu The drop down box which sets the course to the heading the boat is presently steering to and RIK Gi which allows a pre set value to be entered PORT and STBD courses Sailboats only are retained and updated at each press of the ENT
5. the manual supplied or 4 5 Where the damage is caused by exceptional events such as but not limited to o Abnormal levels of magnetic electrical or acoustic interference Lightning strikes Accidents Intentional damage or Negligent use O OOO 5 wear and tear The Warranty is limited to defects in materials or workmanship and does not cover normal wear and tear such as but not limited to corrosion and damage caused through the day to day running of the boat Page 26 h1000 Pilot warranty warranty 6 software B amp G shall not be liable under this Warranty or otherwise for any defect in software incorporated within the product 7 further warranties The Warranty set out in this document is the only Warranty offered by B amp G B amp G makes no further promises in relation to this product such as but not limited to 7 1 That it is suitable for any particular use or 7 2 That it conforms to any particular quality standards 8 transfer This Warranty is not transferable 9 consequential loss B amp G shall not be liable for any damage to persons yachts equipment or any other property or for any other kind of consequential loss 10 governing law This document is governed by and shall be construed in accordance with English law 11 statutory rights This Warranty is offered as an extra benefit and does not affect your statutory rights against the party who sold you the product Page 27
6. with the use of the 10 10 keys display or hand held and the rotary knob and following the on screen bearing and distance to where the incident occurred 5 Recover the person s 6 The MOB feature can be disabled by pressing and holding down the MOB key for five seconds until the display clears The Pilot will now default to OFF Compass Mode N ON MOB Mode Heading Steer 095 Page 23 mob procedure h1000 pilot mob procedure mob automatic recovery power only pilot on 1 Press the MOB key as soon as the person is lost overboard 2 All digital displays will flash the MOB Alarm Message and the alarm will sound if connected 3 Pressing any key on the h1000 Pilot display silences the MOB alarm This action clears the alarm screen and the display now shows the bearing and distance to where the incident occurred The bearing and distance to the casualty are shown under the title Steer on the right hand side of the LCD If necessary reduce the boat speed to less than 8 knots Press the MOB key three times in quick succession to initiate the MOB automatic recovery The autopilot will now control the steering and perform the Williamson Turn back onto the reciprocal heading 7 Press the OFF key to disengage the Pilot as you approach the incident and recover the person s 8 Press and hold the MOB key for five seconds to cancel the MOB function and clear the display of MOB data 9 The Pilot will n
7. ER key whilst in the Tactical Compass page When OK is selected control returns to the Memories Menu Memories Compass Compass Pilot Heading 162 sek 162 Compass Reset trip log sae Alarms Port O46 Lighting Sthd 314 OK reset trip log this function is only available if a speed input is present Reset trip log clears the trip log value back to Zero The stored log however is unaffected by this operation Pressing the UP DOWN key toggles between JM and ENT Memories Memories Pilot Pilot Compass Compass CANCE Reset trip log Reset trip lo ance Alarms Alarms Lighting Lighting alarms Alarm levels for various measured functions can be set or inhibited All the alarms default to OFF on a factory reset If available on the system the Wind speed Shallow depth and Off course alarms can be set from the Alarms menu Selecting Ai activates the Pilot Alarms screen where the Watch timer and Pilot off course alarms can be set It should be noted that two Off course alarms are available with the h1000 Pilot system The first which is located directly on the Alarms menu is triggered from the Tactical Compass page The second Off course alarm located within the Pilot Alarms menu triggers only when the Pilot deviates from the Pilot Set Course Page 13 main menu h1000 pilot alarms The setting procedure for the wind speed alarm is shown The other alarms are set in a similar manner Alarms Wind speed 40 Shall
8. Lighting main menu main menu main menu The Main menu is accessed by pressing the ENTER key The items listed in this menu differ slightly dependent upon the boat type and units connected to the system The tack item will only be listed if the wind interface is connected and the Pilot configured for sail in Dockside Calibration Tack See alSo Page 9 of this manual cancel aborts the tack function now will immediately start the automatic tack function after delay starts the automatic tack function after an adjustable time period memories The Memories menu contains functions which are accessed more frequently and can be changed with the Pilot OFF or ON The memories menu may be accessed to configure the settings for the Pilot Compass Alarms and Lighting and to reset the trip log Page 11 main menu pilot memories Me mories Pilot Compass Reset trip log Alarms Lighting Pilot Memories Tack Settings Delay time O Speed Source OK Pilot Memories Twi moda Tack T A mode Status Speed Source Pilot Memories speed source Tack TA mode peed Source manual Page 12 h1000 pilot Pilot Memories Pressing the ENTER key with fer highlighted takes the user into the Pilot Memories pages Tack see also Page 9 of this manual Pressing the ENTER key with this option highlighted displays the auto tack function delay time setting adjustable between 0 and 99 seconds The
9. adio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference the user is encouraged to try to correct the interference by relocating the equipment or connecting the equipment to a different circuit Consult an authorised dealer or other qualified technician for additional help if these remedies do not correct the problem This device meets requirements for CFR47 Part 15 of the FCC limits for Class B equipment The h1000 Pilot meets the standards set out in European Standard EN 60945 1997 IEC 945 1996 for maritime navigation and radiocommunication equipment and systems The h1000 contains no user serviceable parts An authorised service centre should only make repairs Unauthorised repairs or modifications will void your warranty trademarks All rights reserved No part of this manual may be reproduced or transmitted in any form or by any means including photocopying and recording for any purpose without the express written permission of B amp G Information in this document is subject to change without notice B amp G reserves the right to change or improve its products and to make changes in the content without obligation to notify any person or organisation of such changes B amp G and h1000 are all trademarks of Brookes amp Gatehouse Ltd and may not be used without the express permission of B amp G Page 2 h1000 pilot conten
10. age 21 mob procedure man overboard mob mode Page 22 ON Auto Recoyer Heading Steer ON MOB Mode Heading Steer O98 00r Nm 26 h1000 pilot man overboard key The Man Overboard keyis an optional extra which activates the h1000 Pilot s man overboard procedure For the MOB function to operate the Pilot system must have a boat speed input from a paddlewheel sensor The procedure will not operate when the Pilot is set to manual pre set speed bands or from speed over ground SOG There are two distinct differences in the MOB procedure dependent on the configuration of the Pilot which is either Power Boat or Sail Boat power boats When the h1000 Pilotis installed on powerboats the Pilot can be used for automatic recovery The Pilot controls the steering of the boat and executes a Williamson Turn to steer the boat on a reciprocal heading course back to the point at which the MOB key was initially pressed sail boats When the h1000 Pilotis installed on a sail boat for safety reasons and the need for the boat to tack and gybe back onto the reciprocal course automatic recovery is disabled The user must follow the dead reckoned distance and course displayed on the Pilot screen to manually return the boat to the point at which the MOB key was initially pressed h1000 pilot mob procedure mob procedure mob manual recovery for all boats pilot off 1 Press the MOB key as soon as the perso
11. change i e not when you have just dodged around an obstacle Page 7 pilot mode selection h1000 pilot compass mode 2 page additional compass pages ON Comp Mode Set CRS Comp Mode With the pilot ON pressing the UP DOWN keys will scroll the display to a second and third Compass Mode page 12 7 Knots 26 Page 2 displays boat speed course and rudder cog 123 sag 12 3 position Page 3 displays a track screen of the current data if position information is available Page 8 h1000 pilot ON Heading 262 Wind Mode Set AVA 2 page ON Heading Wind Mode Set AWYA cog 123 Wind Mode sog 12 5 pilot mode selection wind mode wind mode In Wind Mode the Pilot will steer a course that maintains a set target Apparent Wind Angle Set AWA or True Wind Angle Set TWA If the wind shifts the Pilot will alter course so that the actual wind angle to the boat remains the same With Wind Mode selected steer the boat until the desired AWA is displayed and allow the boat to settle Activate the Pilot in Wind Mode by pressing the ON key once Wind angle changes are made by turning the rotary knob the desired number of degrees or by pressing the 10 keys to achieve the desired correction true wind angle If a boat speed input from a paddlewheel sensor is available the Pilot has the added facility to steer to TWA This gives increased steering Stability particularly
12. damaging the casing fixing studs must only be tightened finger tight Rr Sealing Ring lt Fitted at Manufacture Protective Cover Mounting Bracket TEN Pilot Display Unit Page 17 installation h1000 pilot electrical connections external connections Two Fastnet connectors are provided at the rear of the unit The table below shows pin functions 2 2 Pin Number Signal ono Front view of pA Fastnet male connector pins Page 18 h1000 pilot E 10 S HS O auto resume accessories accessories Hand held controller The Hand Held Controller provides remote control over the h1000 Pilot The functions of the six dedicated keys are as follows a 10 gt Ten degree turn to Starboard b lt 10 Ten degree turn to Port c 1 gt One degree turn to Starboard d lt 1 One degree turn to Port e auto resume Switch the Pilot ON Resume the previous course f off Switch OFF the Pilot The Hand Held Controller has an LED indicator that flashes to indicate the h1000 Pilotis operating correctly Page 19 accessories h1000 pilot accessories joystick control The J oystick allows direct control of the rudder via the autopilot computer for quick and responsive steering The J oystick has two modes of operation available to the helmsman giving different steering control as follow
13. downwind Steer to TWA is selected by setting TWA Mode to ON which is found in the Pilot Memories menu Refer to Page 11 of this manual automatic tack The h1000 Pilot has the ability to perform an automatic tack which is particularly useful when sailing short handed The auto tack function is selected by pressing the ENTER key once choosing Tack and selecting now or after delay Selecting now will immediately tack the boat whilst after delay will tack the boat after a pre set countdown period The Tack Countdown time can be adjusted within the Pilot Memories menu additional wind mode pages With the pilot ON pressing the UP DOWN keys will scroll the display to a second and third Wind Mode page Page 2 displays actual wind angle target wind angle and rudder position Page 3 displays a track screen of the current data provided that position information is available Page 9 pilot mode selection navigate mode ON Heading 2 page ON Haw Mode Waypoint East Lepe Brg to WP 195 Dist to WP 15mm ATE 0 2 Lett Page 10 Haw Mode BT 3 page bbu 123 din 3 817 Nm h1000 pilot navigate mode In Nav Mode the Pilot can be used to steer to a waypoint created by the h1000 CND Central Navigation Display or from an external source via NMEA With Nav Mode selected and the Pilot switched OFF steer the boat onto the Bearing to Waypoint BTW ensure that the cross track error is less than
14. h1000 pilot introduction overview MODE Congratulations on your purchase of the h1000 Pilot from B amp G The h1000 Pilot is the latest in autopilots from B amp G and represents B amp G s commitment to providing our customers with the finest marine navigation systems The h1000 Pilot is an easy to use state of the art computerised electronic autopilot system designed as a sophisticated navigation aid and provides many useful features Before you begin using your new h1000 Pilot please take the time to read this manual to help you achieve the full potential from your new system features features The M1000 Pilot is a fully functional autopilot which can be used either as a stand alone system or integrated into an instrument system e Steer to Compass heading COMP Mode e Steer to Wind angle Wind Mode when connected to the h1000 Wind Interface e Steer to Waypoint Nav Mode either from the h1000 CND or NMEA via the Universal Interface e Advanced Control Processor ACP with self learning capabilities e Red background illumination level in 3 steps from zero to full brightness www bandgservice co uk Page 1 introduction h1000 pilot certification warnings amp precautions WARNING DO NOT USE AN ALCOHOL BASED CLEANER ON THIS DISPLAY Note This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to r
15. he calibration menu Security Main menu Calibrations disabled Tack Speed Mermoarias Depth vind Timer oa Compass Calibration Security Page setup Bet decks ae System Ot dag cea Security Pilot sea trial enabled Calibrations Speed Depth wind Calibration Enter PIM 0000 Compass Security Filot dockside Filot sea trial Page 16 h1000 pilot installation installation precautions To avoid electromagnetic interference it is recommended that the Pilot display be installed no less than 0 3 metres from a compass and 1 metre from a GPS The Pilot is water resistant but not waterproof Use the cover when not in use The rear connectors that are not connected to cables must remain protected by their appropriate Caps panel mounting Ensure there is sufficient room behind the panel to accommodate the fixings and connections and using the template supplied cut a hole in the panel in the desired position Fix the mounting bracket into the hole using the screws supplied Note The sealing ring is fitted to the unit during manufacture Its purpose is to prevent moisture penetration and reduce the effects of any vibration transmitted through the instrument panel Press the Pilot Display firmly into the mounting bracket an audible click will indicate that the case is correctly located Secure the unit to the instrument panel by fitting the studs and thumbnuts supplied Caution To avoid
16. n is lost overboard All digital displays will flash the MOB Alarm Message and the alarm will sound if connected 3 Pressing any key on the h1000 Pilot display silences the MOB alarm This action clears the alarm screen and the display now shows the bearing and distance to where the incident occurred The bearing and distance to the casualty are shown under the title Steer on the right hand side of the LCD 4 The boat should now be manually steered back to where the incident occurred by following the bearing and distance shown on the Pilot display 5 Recover the person s 6 The MOB feature can be disabled by pressing and holding down the MOB key for five seconds until the display clears The Pilot will now default to OFF Compass Mode N Naw Mode OFF MOB Mode MOB Heading Steer Man Over o 09g 278 0 07 Nm mob manual recovery for all boats pilot on 1 Press the MOB key as soon as the person is lost overboard All digital displays will flash the MOB Alarm Message and the alarm will sound if connected 3 Pressing any key on the h1000 Pilot display silences the MOB alarm This action clears the alarm screen and the display now shows the bearing and distance to where the incident occurred The bearing and distance to the casualty are shown under the title Steer on the right hand side of the LCD 4 The boat should now be manually steered under autopilot control back to where the incident occurred This is done
17. of the User Pages Timer 00 mins Page 15 calibration calibration Note Manual supplied with your unit Calibrations Speed Depth wing Compass Security Filot dockside Pilot sea trial h1000 pilot For full details of calibrations for your h1000 pilot refer to the Installation Calibration Calibration values take time and effort to set up and it is often necessary to perform various Manoeuvres with the boat For this reason an optional security check is provided before entry into the calibration menus to save accidental resets Refer to the h1000 Pilot Installation Manual for full details covering Compass Dockside and Sea trial calibrations entering secure mode This feature is optional and can be disabled The security check uses a four digit Personal Identification Number or PIN If security has been activated this PIN must be entered every time to access the Calibrations menu After a factory reset the PIN is set to 0000 and in this condition security checking is disabled Security is an option on the Calibrations menu which allows a new PIN to be set Once a non zero PIN has been set the security checking is enabled and all subsequent access to the Calibration menu is restricted Note Once the PIN has been entered for any given session the PIN entry screen is automatically by passed when re entering the calibration menu Upon cycling the power the PIN is once again required to enter t
18. ow a3 shallow Off course 157 Off course Low battery off Low battery off Low battery off Pilot alarma Pilot alarms Pilot alarms Note The low battery alarm is pre set at 10 5 volts and can only be turned ON or OFF lighting lighting Display lighting levels are controlled by the lights key in normal operation but the exact level of illumination can be adjusted for each of the three settings from this menu The levels are numbered in the order they appear when the lights key is pressed and each level can be set as a percentage from 00 off to 99 maximum This menu page also allows the lighting control to be applied either as local this display unit only or the entire system and is useful when zoning particular displays on the boat For example cockpit display lighting can be isolated from a display located down below The OK command returns to the Main Menu Memories Lighting Pilot Compass Level 2 Reset trip log Level 3 Alarms Lighting Zone local Lighting Level 1 TU Level 1 Level 2 50 Level 2 Level 3 30 Level 3 ore Page 14 h1000 pilot main menu The timer can be used for counting down to the start of a race and to record elapsed time The timer can be set to countdown anywhere from 1 minute to a maximum of 59 minutes in 1 minute increments Once started the timer will continue to run in the background even if the timer configuration page is exited The Timer function can be displayed in any
19. ow default to OFF Compass Mode Aus OH MOB Mode ON Auto Recower Heading Steer Heading Steer n 09g i ie 264 irm Notes 1 Activating the MOB Alarm va the Pilot MOB key will also activate the MOB feature on the CND if connected via the Fastnet 2 Activating the MOB Alarm via the CND MOB key will also activate the MOB feature on the Pilot if connected via the Fastnet 3 The Automatic Recovery procedure cannot be initiated from the CND Page 24 h1000 Pilot Dimensions Power Supply Power consumption Display Power Consumption Processor Autopilot Interface Interface Display Display Resolution Temperature range Memory Keyboard Accessories Specification technical specifications 110mm x 170mm 10 16 volts dc 50mA Lights OFF 200mA Lights ON 50mA Excludes Ram amp Accessories NMEA 0183 ver 2 3 Ma Universal LCD Panel FSTN 120 x 80 pixels 10 60 degrees Celsius EEPROM Silicon rubber backlight J oystick Hand held Remote Control MOB Button Paddlewheel External Alarm Page 25 warranty h1000 pilot warranty 1 warranty Brookes amp Gatehouse Limited B amp G guarantees this product against defects in materials or workmanship on the terms and conditions set out below the Warranty 2 warranty period The Warranty continues for 24 months from the date of purchase by the user s excluding mechanical items including but not limited to
20. re values to memory ON engages the Pilot in the selected mode OFF disengages the Pilot from all modes The rotary knob is used to alter the Pilot course in 1 increments scroll through items in a list and alter numerical values Alters the Pilot course by 10 to port Multiple key presses are used for large course changes Alters the Pilot course by 10 to starboard Multiple key presses are used for large course changes Successively cycles through Compass Wind and Nav modes if available Page 5 getting started h1000 pilot getting started Before switching the Pilot on for the first time check that the installation has been wired according to the instructions contained in the h1000 Pilot Installation Manual Comp Mode After initial power up the Pilot displays Heading Comp Mode and shows the Pilot status as OFF Pressing the MODE key with the Pilot OFF scrolls through the available Pilot modes Comp Wind and Nav prowding the data is available on the system Pressing the UP DOWN keys with the Pilot OFF the display scrolls through the six user pages returning to OFF Comp Mode engaging pilot Pressing the ON key activates the Pilot in the selected mode Pressing the UP DOWN keys with the Pilot ON the display scrolls through the fixed Pilot pages for the selected mode OM Comp Mode ON Comp Mode Comp Mode Heading Set CRS B Spd Set CRS 12 7 Knots cog 1237 sagi2 s disengaging pilot
21. s normal In this mode the rudder moves in the direction of the joystick movement when the joystick is returned to the central position the rudder movement stops The greater the movement of the joystick the faster the response of the rudder J ojstick Control proportional In this mode the position of the rudder imitates the position of the joystick When the joystick is returned to the central position the rudder returns to its initial position CW Joystick Mode engaging the pilot in joystick mode Heading Rudder To engage the Pilot 26 A d a e Turn rudder to amidships position e Press the joystick key to engage the Pilot e Move the joystick to Port or Starboard to move the rudder Note that when the Pilot is engaged using the joystick key the rudder position at the moment of engaging will be the central position of the joystick Page 20 h1000 pilot accessories accessories disengaging the pilot from joystick mode The joystick can be de activated by either Pressing the J oystick key e Pressing the Red OFF key on the Pilot display e Pressing the Red OFF key on the Hand Held Controller When the Pilot is disengaged from the J oystick mode the M1000 Pilot will return the mode selected prior to the joystick being engaged Note The J oystick Mode can only be accessed when the Pilot is in the OFF state in Compass Wind or NAV modes and cannot be selected if the Pilot is already engaged P
22. ts contents Overview 1 Features 1 Certification 2 Trademarks 2 Contents 3 Controls 5 Getting Started 5 Engaging Pilot 6 Disengaging Pilot 6 Pilot mode selection 6 Compass Mode 7 Navigate Mode 9 Wind Mode 10 Main menu 11 Main Menu 11 Tack 11 Memories 11 Pilot Memories 11 Resume 11 Tack 12 TWA Mode 12 Speed Source 12 Memories Menu 13 Compass 13 Reset trip log 13 Alarms 13 Lighting 14 Timer 15 Calibration 16 Entering Secure Mode 16 Installation 17 Precautions 17 Panel mounting 17 Electrical Connections 18 External Connections 18 Accessories 19 Hand Held Contoller 19 J oystick 20 Engaging the Pilot in J oystick Mode 20 Disengaging the Pilot in J oystick Mode 21 Page 3 contents h1000 pilot contents Man Overboard MOB Mode 22 Man Overboard Key 22 Power Boats 22 Sail Boats 22 MOB Manual Recovery For All Boats Pilot OFF 23 Manual Recovery for all Boats Pilot ON 23 MOB Automatic Recovery Power Only Pilot ON 24 Technical Specifications 25 Warranty 26 Page 4 h1000 Pilot controls controls Light control The lighting level can be changed at any time by pressing the LIGHTS key This causes the lighting level to cycle in the sequence high medium low off and then back to high The UP DOWN keys are used to move through data pages scroll through items in a list and alter numerical values Press the ENTER key to select the Main Menu from a data page select items from a list entry and sto
Download Pdf Manuals
Related Search