User Manual PDF
Contents
1. 8 84 hot water supply shut off valve not included 85 721301 3 8 x 1 2 check valve adapter housing 86 721201 check valve 87 721202 strainer 88 721302 1 2 x 3 8 adapter for 3 8 shut off valve 89 721203 water supply washer 3 8 Eo Adjustable Wrench 2 Phillips Screwdriver 1 2 Insert 3 8 controller end 11 Connect spray head water hose connector 23 of spray head connector to spray head 12 water hose 22 into the faucet with washer 28 inserted 22 spout 11 3 amp Do not lift the spout by pulling sensor ae cable or hose 42 Installation Procedure A 11 Mount Digital Controller 71 on wall below bottom of counter top about 4 6 with three mounting screws 77 Insert sensor cable 42 spray head water hose 22 and faucet mounting pipe 13 through mounting hole of counter top Connect the 3 8 x 1 2 adapter with check valve housing 85 which includes a check valve 86 pre installed in adapter and a strainer 87 on a 1 2 water supply shut off valve 82 If the shut off valve connecting thread is 3 8 install attached 1 2 x 3 8 adapter 88 with 3 8 washer 89 Note 85 Be sure to install check valve 86 and strainer 87 to prevent hot cold water flow crossover S i 87 4 Make sure top spout swivel can rotate 75 degree on each side 5 Place rubber washer 14 and metal washer 15 on mounting pi2. Then hold hand in front of Sensor A and B or in front of Sensor C to start water flow with Preset 1 setting Fie l LED Flashes green once LED 2 How to save Preset 1 2 1 Adjust water temperature and flow accordingly Operation Procedure 2 2 Hold hand in front of both Sensor D and E to save the current water temperature and flow setting as new Preset 1 setting LED Flashes green once How to reset enable Sensor C Easy Sensor With water flow off hold finger in front of Sensor A to reset Sensor C i 2 3 Hold hand in front of Sensor A and B again to stop water flow LED Flashes green two times C amp LED 3 How to start and save Preset 2 setting start with Sensor E to activate or Interference of Sunli save Preset 2 setting How IR sensor works LED Flashes green once IR sensors use infrared IR light to sense nearby objects A pulse of infrared light is emitted and spreads out in a cone shape for a short distance If an object is within the cone s area then IR light will be reflected and received by IR detector activating the sensor function LED J 4 How to reset Default Preset 0 setting Q Faucet will reset to Default D a Setting condition after 30 seconds without new operation command Repeat same procedure gt 1 to 2 but start with holding Sensor D and E to activate or save Default LED Keep sensors surrounding area clear Preset 0 setting Some objects
3. easy operation Solid brass construction for durability PVD coating features an easy to clean surface which is more durable and resistant to corrosion Not available in all models iSense Touch Free Intelligent Faucet TIF D High Flow A Hot Water E Low Flow B Cold Water C Easy Sensor amp LED 1 Sense C for intermittent flow 2 Sense A amp B start and stop continuous flow 3 Sense D amp E to save as default Infrared Sensor activation zone Operation Procedure Sensor Zone amp Distance There are two sensors A amp B and C amp D on each side of faucet to control water temperature and flow On the front of faucet is sensor C for intermittent flow and a LED indicator ensing Zone Hold your palm about 1 5 inch in front of two sensors for simultaneous activation How to start intermittent water flow with C amp LED Easy Sensor C _9 teat To Hold hand or object under spout a eee in front of Easy Sensor C How to activate Touch free sensors sensingarea to start intermittent water flow remove hand or object from Sensor C sensing area to stop water flow LED Flashes green once Hold a finger about 1 5 inch in front of sensor for activation Operation Procedure How to start continuous water flow with Sensor A amp B Hold hand in front of K both Sensor A and N Sensor B to start continuous water flow rh LED Flashes green once Water
4. flow will stop after 5 minutes if no activity on any sensor I LED How to adjust water temperature Hold finger in front of Sensor A hot to raise water temperature A Hot LED Flashes once every step up Red over 100 F Yellow over 70 F Green below 70 F Hold finger in front of Sensor B cold to lower water temperature LED Flashes once every step down f LED Red over 100 F Yellow over 70 F Green below 70 F How to adjust water flow Hold finger in front of D Increase flow Sensor D to increase water flow LED Flashes once every step down Red high flow Yellow medium flow Green low flow Hold finger in front of Sensor E to reduce water flow E Reduce flow LED Flashes once every step down Red high flow Yellow medium flow Green low flow How to save Default Setting Preset 0 Hold hand in front of both Sensor D and Sensor E to save current water temperature and flow setting as new Default Setting for preferrable usage D LED Flashes green once How to stop continuous water flow Hold hand in front of both Sensor A amp Sensor B ACS again to stop continuous i end water flow LED Flashes red once LED Preset and Saving Seti 1 How to start Preset 1 setting D 1 1 With water flow off hold finger in front n of Sensor D to start Preset 1 setting LED Flashes green once LED 1 2
5. running to dislodge debris Sensor Troubleshooting Table Symptoms Probable Causes Recommended Action 1 Sensors A Debris on the sensor lens A Use mild soap and water to gently clean sensor lens malfunctioning B Sensor is detecting object B Rotate the spout away from the object or remove the object from the sensor zone C Sensor affected by interference C Refer to the Interference of sunlight section to of sunlight or other light source disable pause the Easy Sensor 2 Sensors are not A Loose sensor cable connection A Check sensor cable connection to the Digital Controller workings LED not B Debris on the sensor cable connector B Gently clean the cable connector and cable connection it port with clean dry brush C AC DC adapter power supply is not C Confirm the AC DC adapter is powered the adapter connected green light is lit and connected to Digital controller D 4 AA backup battery low voltage D Confirm the 4 AA backup battery is powered at minimum 4 8 volt Installation Manual IMPORTANT INSTRUCTIONS NOTICE The faucet system uses a 6 volt DC power and a 120 240 volt AC adapter Please follow all plumbing electrical and building codes WARNING When using electrical products basic precautions should always be followed including the following 1 Risk of electric shock Connect only to an unswitched circuit protected by a Ground Fault Circuit Interrupter GFCI 2 Disconnect power before servi
6. such as mirrors or bottles with smooth shiny surfaces can reflect the infrared light from farther away and cause false activation How to pause disable Sensor C Easy Sensor With water flow off A hold finger in front of t Sensor A to stop pause Sensor C for working r in the sink area LED Flashes green C amp LED N P and red once Sunlight interference Sunlight or flames also present a problem as they emit a lot of IR light and thus interfere with IR sensor providing Sensor C paused disabled to allow user to proceed with housework A false readings r J in the sink area gt lt J Operation Procedure How to stop false activation The longer sensing distance of Sensor C Easy Sensor is the sensor most likely to be activated by direct sunlight in sink area especially in morning sun or sunset light You can pause disable Sensor C by D sensing Sensor A with water LED Y om LED flashes green and red Should water flow be activated by sun light on Sensor C water flow can be stopped by holding your hand in front of Sensor D and E for 5 seconds to stop water flow and pause disable Sensor C Re enable Sensor C You can re enable Sensor C by activating Sensor A with water off LED Flashes green two times Maintenance 1 Cleaning the faucet The completely touch free faucet requires very little maintenance Wipe surfaces clean with a soft damp sponge or cloth Never use clean
7. 4 on Digital Controller Installation is now complete Install 4 AA batteries in backup battery box 46 and hang box on wall with L shape screw 76 ed Turn on cold and hot water supply valve 82 84 Check for any water leakage LIMITED WARRANTY For product s sold and delivered in U S A amp Canada only COVERED PRODUCT S Cinaton iSense Touch Free Intelligent Faucets LIMITED WARRANTY COVERAGE Cinaton Inc hereinafter Cinaton warrants the Covered Product s to be free of all defects in material and workmanship for a period of five 5 years from the date of original purchase This warranty extends to the original buyer and each successive buyer within the warranty period Within the period of this warranty Cinaton will repair or replace free of charge any part proving defective in material or workmanship All warranty repairs and service will be performed by Cinaton Service Center in California This warranty is limited to repair or replacement with identical or similar parts only WARRANTY EXCLUSIONS This warranty does not apply to any costs repairs or services for the following Service calls to correct the installation of the Covered Product s or to explain the usage of the product s to the buyer Repairs necessitated by use other than normal use Damage resulting from misuse abuse accidents alterations or improper installation Corrective work necessitated by repai
8. Cinaten dJust like magic User Manual Model 2201 K2002 TIF Touch Free Intelligent Faucet Please read the User Manual before removing parts from box Save this User Manual for future reference iSense Touch Free Intelligent Faucet System Technical Data 1 Power supply AC 110 240 Volt 4 AA backup battery box 2 Water supply pressure 20 100 psi normal 60 psi 3 Operating temperature 37 F 160 F 4 Aerator water flow Kitchen 2 2 GPM Lavatory 1 5 GPM 5 Controller Digital Controller 6 Maximum water temperature setting 110 160 F Backup Battery Hot Water Cold Water Features 1 Innovative amp intelligent iSense touch free technology provides an easy to use convenient and unique faucet experience Simple Clean Stylish Design no handles or buttons to operate Experience a new way of food preparation and clean up reducing exposure to bacteria Beyond your expectations 5 proximity sensors hands free combine to make everyday tasks easier Full water temperature and water flow control without touching the faucet Personalized settings three user defined water temperature and flow settings for personal convenience Backup battery for continuous use during electric power outage Maximum temperature setting for ADA compliance No scalding risk for any age Children the elderly and the disabled Single hole mount for less counter clutter and
9. ackup battery low voltage Plug the AC DC adapter or replace the 4 AA batteries 6 Automatic calibration The touch free faucet system is automatic calibrated periodically The visible LED flashes in red and green during automatic calibration The process takes about 30 seconds Symptoms Probable Causes Recommended Action 1 No water flow off valves are closed A The cold and or hot water supply shut A Confirm the water supply shut off valves are open kinked B The cold and or hot supply hose is B Confirm the supply hoses are not kinked If coiled maintain an inside diameter of 3 76 mm C The spout outlet hose is kinked C Confirm the Digital Controller is located within 4 102 mm to 6 152 mm from the faucet base LED not lit green D Continuous water flow not functioning D Refer to the Sensor Troubleshooting Table section LED not lit green E Intermittent water flow not functioning E Refer to the Sensor Troubleshooting Table section F One or both of the water supply strainers are clogged F Refer to the Cleaning water supply strainer section Faucet Troubleshooting Table Symptoms Probable Causes Recommended Action 1 No water flow G Water flow control Sensor D E G Hold finger on Sensor D to increase water flow turned too low H Malfunction of system p
10. cing 3 Please read all instructions thoroughly before beginning installation to avoid risk of injury or property damage 4 Do not open the Digital Controller Open the Digital Controller will void the warranty 5 Do not store open chemicals near the Digital Controller 6 Rinse cleaning rags and sponges with fresh water Installation Procedure 11 faucet spout 12 spray head CP 721005 SN 721006 13 722001 mounting pipe 14 722011 rubber washer 15 722021 metal washer 16 722031 mounting bracket 17 722034 mounting screw x3 2 1 2 x 3 8 universal joint 721311 for K2002 721312 for 2101 22 720004 spray head water hose 24 721204 spray hose weight 25 721205 spray hose weight bolt x2 26 721304 cold water inlet quick connector 27 721304 hot water inlet quick connector 28 721007 spray head washer 4 sensor ABDE 755021 C 5 755022 7 755023 9 755024 42 705035 sensor cable 44 750001 AC DC adapter 46 750101 4 AA backup battery box 71 710000 Digital Controller 72 sensor cable input port 73 AC DC 6 V input port 74 4 AA DC backup battery input port 75 maximum temperature adjusting knob 76 722035 battery box mounting L shape screw 77 722036 controller mounting screw x3 78 750110 4 AA backup battery 81 720002 cold water supply hose 3 8 82 cold water supply shut off valve not included 83 720001 hot water supply hose 3
11. ing chemicals or abrasive material such as a brush abrasive sponge or scouring pad to clean faucet surfaces or sensors 2 Clearing water supply strainers Water flow may decrease in volume over time as a result of debris trapped by the water supply strainers To clear two strainers located in water supply adapter Shut off cold and hot water supply valves Disconnect the 3 8 x 1 2 adapter housings Flush the strainers with water until clear of debris Reinstall strainers and connect adapter housings Turn on cold and hot shut off valves and check for any leakage Faucet Troubleshooting Table 4 Setting maximum water temperature 8 a Adapter housing S gt Strainer 1 2 Valve 3 8 Valve A 3 Resetting the system Should the system ever malfunction it may be necessary to perform a reset To reset Unplug the AC DC adapter Disconnect the backup battery power wire Wait for 10 seconds to clear the memory Plug the AC DC adapter and reconnect the backup battery cable The system will be reset to factory settings The water temperature adjustment knob on Digital Controller can be set between 110 F 43 3 C to 160 F 71 1 C to prevent scalding risks especially to children the elderly and the disabled 5 Power supply low voltage alert The visible LED will flash yellow when low voltage power supply from AC DC adapter power cable lost connection or 4 AA b
12. pe 13 from bottom of counter top Hand tighten mounting bracket 16 1 2 Valve 3 8 Valve 9 k Connect 3 8 cold water inlet 6 supply hose 81 to 3 8 x 1 2 Tighten three mounting adapter housing 85 81 screws 17 with a screwdriver For hot water supply repeat step 7 and 8 using 3 8 hot water inlet supply hose 83 Installation Procedure 10 ae me sir gue aneen oa Install spray hose weight 24 on spray head water hose 22 Hail a nose ta about 3 from the lowest bending point of hose Then secure spray hose weight bolt 25 into spray hose weight 24 on Digital Controller Warning The hose quick connector must be inserted completely to prevent 26 hose falling off from Digital Controller 11 With same procedures insert quick connector of 3 8 hot water supply hose 83 to hot water inlet connector 27 on Digital Controller 14 Insert sensor cable 42 to sensor cable input port 72 on Digital Controller 71 Digital Controller 12 Connect 3 8 spray head water hose 22 to universal joint 21 on Digital Controller 15 Insert 6V AC DC adapter 44 cable to 6V AC DC input port 73 on Digital Controller Installation Procedure 16 18 Plug in AC DC 6 volt adapter 44 into an unswitched AC wall outlet Then insert power cable of 4 AA DC backup battery box 46 to backup battery input port 7
13. r consequential damages so the above limitation or exclusion may not apply to the buyer REGISTRATION We recommend that the buyer register the product online at www cinaton com c register php This will facilitate any warranty repairs or service if needed 11 Cinaten Just like magic Thank you for purchasing this Cinaton product To receive more complete service please register your product at www cinaton com c register php Product Model Serial Number on the sensor cable tag Digital Controller Model on the Digital Controller 14014 Gannet Street Santa Fe Springs CA 90670 Tel 562 921 8009 Fax 562 921 0688 cabal www cinaton com info cinaton com AON 2015 Cinaton Inc No part of this publication may be reproduced or used in any form or by any electrical or mechanical means without permission in writing from Cinaton This includes electronic or mechanical means such as photocopying recording or information storage and retrieval systems The material in this manual is subject to change without notice
14. rogram H Refer to the System reset section Digital Controller not functioning Replace the Digital Controller 2 Low water flow A The cold and or hot water supply shut A Confirm the water supply shut off valves are fully open off valves are partially closed B The cold and or hot supply hose is B Confirm the supply hoses are not kinked If coiled kinked or twisted maintain an inside diameter of 3 76 mm C The spout outlet hose is kinked C Confirm the Digital Controller is located within 4 102 mm to 6 152 mm from the faucet base D One or both of the water supply D Refer to the Cleaning water supply strainer section strainers are clogged E Digital Controller not functioning E Replace the Digital Controller 3 Low water A The hot water supply shut off A Confirm the hot water supply shut off valve is fully temperature valve is closed or partially closed open B The hot supply hose is kinked or B Confirm the hot water supply hose is not kinked twisted If coiled maintain an inside diameter of 3 76 mm C The hot water supply strainer is C Refer to the Cleaning water supply strainer clogged section D Maximum water temperature setting D Refer to the Setting maximum water temperature is too low section E Digital Controller not functioning E Replace the Digital Controller 4 Poor spray pattern A The spray nozzles are clogged A Rub your finger over the nozzles with water
15. rs made by anyone other than a Cinaton s authorized service technician HOW TO OBTAIN WARRANTY SERVICE To obtain Warranty Service the buyer must produce proof of purchase original sales receipt and notify Cinaton of any defect malfunction or nonconformity promptly upon discovery by calling the toll free number 855 348 8080 or by writing to Cinaton with full description of the problem Upon receipt of such notice and verification of proof of purchase of the Covered Product s Cinaton will send out to buyer the Warranty Service Instruction and Authorization for Return of the Covered Product s Cinaton will do one of the following after receipt of the returned product s Service or repair the Covered Product s to conform to the applicable warranty Replace the Covered Product s with goods that are identical or reasonably equivalent to the warranted goods The buyer should carefully pack the Covered Product s preferably in the original packing materials and deliver it together with a copy of the original purchase receipt and a description of the problem to Cinaton If the buyer sends the product s by U S mail we recommend that the buyer insures it and send it with return receipt requested We accept no liability for product s lost or misplaced in shipment LIMITATION OF DAMAGES In no event shall Cinaton be liable for consequential damages for breach of this warranty Some States do not allow the exclusion or limitation of incidental o
Download Pdf Manuals
Related Search