87-UP Harley Heritage Softail
Contents
1. Attach the computer to the top using the supplied Velcro with the wire facing rearward Pull all extra slack from the harness into the bag make sure the bag closes easily You want all the plugs extra wire and air lines pushed toward the back and below the level of the top Once complete you should be looking at something like the picture below Next we will tidy some things up 24 FINISHING UP Now it is time to reinstall everything you took off and do a final check of everything Install the right saddlebag then reinstall the seat making sure all your wires are routed neatly tied off nicely and don t interfere with the seat installation Once all of this 1s accomplished we should get the bike on the ground and with a helper cycle the wheels up and down a few times having your helper make sure the air lines are not being scuffed or are over tight and that the wires are out of the way of anything that could damage them Double check all your bolts for tightness Now we can dial in the legs and adjust the wheels if needed LEAKS This system uses air and air loves to leak The fittings we use are tested for leaks before shipping but we have a few simple tests to make sure you have no leaks or just insignificant ones if any Set the wheels down and leave the system on Put the kickstand down and turn the bars all the way left If the compressor makes noise more than once every two minutes you may have a leak2. hold the bracket steady and slowly rotate the wheel Every time a bolt passes the sensor the light should get bright and turn off after it passes If this is not happening you may need to get the sensor a bit closer to the P 5 D d LOS bolts SMM 1s a very small m If you have to move the sensor m you may have to bend the bracket a bit No matter what you need to do you MUST make sure that as the wheel turns the light works as described above Once you are certain tighten the bolts and test again The automatic retraction of the legs as well as their deployment RELIES on this sensor being placed perfectly 24 Once satisfied with the mount route the wire up the swingarm making sure it 1s clear and safe You need to leave a little slack as it joins the other wires under the seat the swingarm moves and we need this slack so the wire 1s not broken as the wheel goes up and down Now we can mount the compressor 27 INSTALL THE COMPRESSOR Now that the air lines and wire harness are ready we need to re mount the left saddlebag and install the compressor While mounting the bag run the two air lines into the hole you drilled earlier We like to place the forward mount on the rubber mounting isolator so it 1s supported and tilt the pee to o get the lines in as seen here Rn ee S Install and tighten the mounting bolts CRAFTSMAN inside the bag and install an acorn nut on the stud from the rubber isol
3. needed in the future Please skip this section unless you have been instructed to reset the system by Chopper Design Turn the ignition to Accessory and start the LegUp System hold right button for 3 seconds The system should be set at the factory for proper pressure but some wheel adjustment may be needed If it has been determined that Maintenance Mode is needed Sit on the bike and hold it level If both lights on the switch box are flashing the system is in maintenance mode If not PRESS amp HOLD both buttons until all lights flash Do your best to press both buttons at the same time so the system doesn t respond to what it thinks is a request to lower the legs Once flashing hit both buttons for an instant to get the system in the DOWN setting mode lower yellow LED flashing Touch the left button briefly the wheels should go down immediately This is VERY quick don t be startled Using very short pushes of the left button press and then feel the stability of the bike If it feels firm enough try leaning the bike a bit If the wheels return the bike to upright there 1s likely enough pressure Put your feet on the floorboards the bike should stand on its own Rock the bike a bit left and right being prepared to put your feet down If the bike continues to come back to upright the DOWN stop is now set and we can move on Hit both buttons for a moment to get into the UP stop mode Usually hitting the left button
4. ves sas 33 IEEUSLEIRC TIONS i store eot E aree ES er ER o ER iS 34 HARDWARE EST cct eekeessctoso neue en E aep oa CE EUER ERES ORE F4 PA RR SES eEpRR T V a eS 35 INTRODUCTION This manual covers installation of the Generation II LegUp LandinGear system by Chopper Design Services This system should only be installed by a qualified technician or those with above average mechanical skills If you are not SURE that you can perform this installation please contact us and we will help you find a qualified shop to assist you While the Generation II System holds your bike upright very well you are STILL responsible for balancing the bike The system WILL relieve you of some of the weight of the bike and help you avoid balance problems as you approach a stop maneuver at slow speeds and back the bike up Improper installation will void your warranty so please be very careful Thanks for choosing LegUp Warranty Chopper Design Services warrants the LegUp system for a period of one year from date of purchase This warranty covers replacement parts and or manufacturer defects Incidental damages or costs are the responsibility of the purchaser Defective parts are to be returned to Chopper Design at the address below Purchaser must contact Chopper Design to receive a Return Material Authorization prior to returning defective parts to Chopper Design Abuse improper installation or use collisions or accidents are not covered under th
5. we do and plug the 8 pin plug into it We just want to make sure everything is working Turn your bike to Accessory Mode counter clockwise Your speedometer will illuminate and if everything is working properly the compressor should turn on for about 6 seconds to fill the onboard air tank The RED LED ON i The Sensor Should Not Be Lit Take a metal object screwdriver wrench etc and hold it on the flat face of the sensor it has a circle embossed in it The LED should light up and go out when you move the metal away If not check all your connections The mount here is not a Softail Mount Next press the rightmost pushbutton on the handlebar switchbox and hold it for at least 3 seconds One or both LEDs on the switch panel should light up or blink we really don t care which at this point If this occurs you are doing well If both LEDs are flashing maintenance mode you can skip the next step which is to press both buttons until both LEDs flash Next press both buttons again for just an instant If everything is working the bottom or yellow LED on the switch box should flash and the top LED should be out The next step requires some care If the bike is still on the lift have a helper hang on to it as you touch the left button for just a split second The legs should move down likely until the wheels hit or just miss the lift and they do this VERY quickly Again be careful as they could lean the bike 1f one w
6. Generation I landingear com US PATENT 8 235 419 B Installation Manual Generation II Harley Heritage Softail Models 1996 Present Copyright 2015 Pete Giarrusso Inc D B A Chopper Design Services All Rights Reserved Table of Contents INIRODUC d 8 7 M S 4 ba 3 419 9l e 5 INSTALLATION INSTRUCTIONS eere ee eere eee enne nenne ree oe 6 PREPARE POR INSTALLA LION oiirereseree orig eese eo ee FE eee ie ee eo PPP Peer rer er 7 PREPARELEBRISADDEEDBAQG 5i 5E H0 p0R ER EEYERER T naO aai 8 CONTROL SW EE CEH BOX iissscssceccsssscsdsccssnnossseccesssasssssasessersassevesvessocacaccesssssssssesess 9 WIRING HARNESS o 10 LEGS MOUNTASSEMBELIES isicsosin ea oain sunean 13 1999 amp EARLIER LEG MOUNTING i cccccscsssccscccccccscccscccccssccccccccssseses 16 SB E 62 9 1 4 LINES Lt 18 MOUNTPROXIMITY SENSOR sissssssscescasssstsessestassasssccccsvccstacessssesesssecsossssseseexs 21 INS TALE THE COMPRESSOR sscsscscssocsassssassscccccscansssnsesvecssscacsevstesosssavocccsscaests 22 FINISHING B toes M 25 FINAL ADJUSTMENTS amp MAINTENANCE MODBE ecce ceee eene ee eterne 26 MAINTENANCE MODE uses et ebat epe aded Es Ie vod UU oosese eise va tote easiest evens 26 WHEBELJADIUSTMENE i nttistisioeiutuetos Cei eee aeo e O 27 TELS 193 141 RJ gos 30 GENERATION I UPGRADE INSTRUCTIONS 32 PRE 1996 WIRING ADDENDYU ML 625625 00S eR 0E bU Io A 2E OP Lo Giove e
7. at the lines that connect to the compressor or the tank fittings Some soapy water will tell you where you will need to remove the compressor top to test for these leaks Assuming the compressor doesn t lose enough air to kick on after 2 minutes you should be fine You can turn the bike off and wait to see if in 5 minutes the bike is not as stable as it was when the wheels were first lowered If it lasts the 5 minutes and is still very stable you could still have a leak but not one that would be a problem on the road Leave the bike on its wheels overnight again kickstand down bars full left in case the legs lose a lot of air the bike will land on its stand If in the morning the bike is still stable you have no leaks If there are leaks the fittings on the air cylinders would be the first for the soapy water check with the two small line fittings on the compressor next If you need help with these please feel free to call us at 407 834 5007 25 FINAL ADJUSTMENTS amp MAINTENANCE MODE The next two sections are typically NOT needed We include them to document your system thoroughly but MOST people will never need to use either section MAINTENANCE MODE NOTE Maintenance mode is a procedure that TEACHES the computer how much pressure to use when it lowers the wheels and how much pressure to release when raising the wheels We always set this at the factory ALWAYS We include this procedure in case it is ever
8. ator Make sure the bag mounts are tight Next we want to attach the air lines to the compressor On the compressor should be Sal two short air lines with fittings on the ends You may want a bit of help here to keep the saddlebag open On the compressor should be two short air lines with connectors on the ends Perch the compressor on the top ledge of the open bag Notice that the tank goes toward the bike as you can see below Attach the air lines from the bike to the connectors attached to the compressor red arrows These lines simply push into the in line connectors as they did on the cylinders on the legs Once the air lines are attached plug in the 8 pin connector to the connector on the compressor It only attaches one way make sure it 1s solidly attached At this time make sure you keep the 12 pin plug above the top of the compressor so you won t have to fish for it once the compressor is in the bag You are about to see how tight a fit this device is in your saddlebag 23 Tilting the front of the compressor system up carefully lower it into the saddlebag allowing it to settle into a spot as far back as it can go The compressor should feel secure where it sits the rubber straps around the air tank should keep it from wanting to tip Assuming you are happy d with its placement find the E 7 computer and plug it into the 12 pin plug you kept above the top of the compressor while installing
9. e On the next page we have some pictures to help you understand what we have tried to show and explain here 28 different The right c one is shorter than the left shorter is what bikes that are a bit lower require At left is a picture that shows the angle of the actuator when the wheels are set properly Notice the bottom of the cylinder silver inside the black legs is further forward than the top Yours should look like something like this If you are still not getting the stability we describe here please call us and we will try I to determine why not 407 834 5007 29 TEST RIDE Get the bike to a clear paved mostly level area where you can test ride it Start the bike turn on the LegUp system and lower the legs The first test should be done in a straight line Put the bike in gear and slowly accelerate You may notice that the bike tends to want to steer a small amount left or right This is normal unless it is severe Effectively you are driving a trike and steering is done with the handlebars NOT by leaning Once underway we recommend you keep your thumb near the left button and press it to raise the wheels 1f there are any surprises the top LED should flash at around 6 MPH meaning the legs are retracting It 1s difficult to lean on one wheel or the other as you leave so you may wish to raise the wheels manually if the bike is steering due to uneven pavement Assuming the legs are retracted you sho
10. els Contact Chopper Design for help with fitment on anything but the above model in a completely STOCK condition IF YOU ARE UPGRADING FROM A GENERATION I SYSTEM PLEASE READ THE ADDENDUM TOWARD THE END OF THIS MANUAL ON THIS SUBJECT FIRST We suggest that you read this ENTIRE manual before starting this installation It will save you time and frustration Place the motorcycle on an acceptable bike lift You will need to keep the bike on its wheels for most of the installation and jack the rear wheel off the lift for some portion of the installation Make SURE the motorcycle is secure on the lift Remove both saddlebags one we will be modifying slightly and installation of the legs 1s MUCH easier with the saddlebags out of the way This manual is available at http landingear com pdf g2installmanuS T pdf It may be easier to see some of the pictures in color there Let s begin PREPARE LEFT SADDLEBAG One of the first things we want to do 1s to drill a small hole in the left saddlebag to allow the air lines to enter the bag Make note of the area we are showing you in the picture below The arrow points to a recess on the back of the bag We want to drill a single 5 16 hole here The back of the bag is very soft plastic so no pilot hole is needed There are two things to watch for here Make sure you have the left bag and make sure you drill the hole where we show you We are going to run 2 small airlines through t
11. er strut In the picture below you can see that we used a wire tie just past the fender strut to hold both air lines Tying the hoses just at this spot will maintain the curve you see in the top left picture that will keep the line away from 7 xb E the belt and the swingarm Once this tie is in fes place try to see if the hose can reach the belt If it can you must adjust the ties until the hoses are safe Whatever you do it 1s critical that the lines can t get burned or scuffed A little extra patience here will relieve tons of frustration later from holes in the air lines Keep in mind these are air lines tying them too tightly can restrict the air flow Below we have a shot of the lines tied as they should be We added 2 more ties and have arrows where all 3 should be Take note of the rearmost point This should allow a smooth curve into the hole we drilled in the bag z Check Both Sides before we move on that by 7 lowering and raising the legs there is plenty of d slack for the lines Readjust your wire ties 1f need be but make sure they work properly to avoid headaches later 19 INITIAL SYSTEM TEST For the time being assuming all the plugs under the seat are plugged in we need to plug the computer into the 12 pin plug hanging off the left fender strut If you did not attach the negative cable to the battery this would be the time to do so Find the compressor and put it somewhere stable on the lift is what
12. es for safety The black wire can be hooked to any ground the battery a screw on the frame or any black wire in the harness 33 ILLUSTRATIONS Proximity Sensor hiya sensor aide Compressor Plug Plug Black Harness side Brown Sensor side Orange Harmesr side HARDWARE LIST 2 3 8 16 X 2 Grade 8 Studs for leg mount 00 Up 4 3 8 16 Hex Nuts for studs 00 Up 2 3 8 Lock Washers for studs 00 Up 2 3 8 16 Acorn Nuts for studs 00 Up 2 15 13 X 1 4 Hex Nuts for leg mount 99 down 2 12 13 Locking Nut for leg mount 99 down 2 4 Rubber Mounts saddlebag support 2 4 20 X Aluminum standoffs M F for rubber mount 2 4 20 Lock Nuts for rubber mount 2 4 20 Chrome Acorn Nuts for rubber mount 4 14 20 Hex Bolts for slide 4 14 Flat Washers for slide 2 14 20 X 1 25 Hex Bolts for adjuster 2 4 20 Hex Nuts for adjuster 1 Softail Chrome Floorboard Kit 2 1 4 20 X 2 Chrome Allen Bolts w Split Washers 95 Down 2 4 X 7 16 X 7 8 Spacers HB Bracket 95 Down 2 5 32 Black Air Line 5 Foot Long cylinders to saddlebag 2 5 32 Black Air Line 2 Foot Long valves to unions 2 5 32 Union Fittings Big amp Small Wire Ties self adhesive clips 35
13. he bottom LED Should not be LIT SOLID if the bike is travelling over IOMPH In the event it is the wheels will deploy instantly if you try to set them as above this is dangerous You MUST re visit the sections on testing the proximity sensor You should always be aware that this light should NOT be on if you are traveling at speed and Arming the system for deployment should only be attempted if the lower LED is Not Lit Please see the User Manual for more information on Proximity Sensor Failure 30 The next thing to try is to make a turn from a dead stop with the wheels down As soon as you start the bike moving turns can only be made by using the handlebars The LegUp system 1s too strong to allow a great deal of lean with the wheels down If you need to make a turn shortly after departing from a stop raise the wheels manually left button and you will get complete control again The next thing to try 1s slow speed maneuvering with the wheels lowered If you keep your speed down most slow speed maneuvers can be accomplished with your feet up keeping in mind that at about 6 MPH the wheels will come up automatically You can try full lock turns in both directions and the bike should stay upright with your feet up Understand it is always a good idea to keep your feet near the ground during these maneuvers if you can A mechanical failure or a wheel in a pothole could upset the bike Because the wheels are right behind your legs
14. heel touches the lift and the other does not Press and hold the right button and they should move up Again with the bike on the lift you have to be very careful here If all of the above has occurred great If the legs are not all the way up press and hold the right button until the legs stop and turn the ignition switch off The test is now complete Disconnect the Compressor and computer and set them aside Let s move on to mounting the Proximity Sensor 20 MOUNT PROXIMITY SENSOR This step is crucial Understand it before starting The proximity sensor tells the system how fast the bike is traveling The proximity sensor mounts to the swing arm at the rear pulley It will mount SMM from the pulley You need to Jack up the rear wheel so we can spin it to test the sensor and its placement Make sure the bike is in neutral With the bike up as described above turn the ignition switch to the accessory position The LED on the sensor should be out Bolt the proximity bracket to the rear most bolt on the belt guard so the sensor aligns near the pulley bolts Adjust the bracket so the main part of the sensor 1s aiming at a pulley bolt and is centered on it you may have to turn the wheel to do this What we are looking fori iS FOE the LED to go bright and OFF as a pulley bolt passes the sensor Play l with this by rotating the wheel back and forth while holding the bracket in place Once you feel you have the right place
15. his hole It is high enough and hidden enough that it should not allow any water infiltration If you are still concerned once we reinstall the saddlebag you can use silicone to seal this hole Exact placement of the hole 1s not terribly critical Once complete it should look like the bag below The next step is mounting the Control Switch Box CONTROL SWITCH BOX NOTE ON pre 1996 models you will need a bracket to mount the switch housing which we should have supplied In this case remove the bolts that secure the clutch perch clamp on the left side install the supplied bolts through the bracket that has the box mounted to it through the supplied spacers and into the clutch perch Blue Loctite here Once tightened follow the rest of these instructions Control Box Plug If your bike requires no bracket as mentioned above remove the bolt on the top of the left switch housing on the handlebar Find the long thin bolt thread it through the Control Switch Box insert the spacer on the bolt with a drop of Blue Loctite and thread the bolt into the switch housing Square the box before tightening the bolt you may have to re align the mirror for clearance Route the wire inside the clutch lever and down the bar Use wire ties to hold the wire to the bar Run the wire through the top triple tree if you can to control it The idea here 1s to get the wires neatly to the front of the tank and routed under the tank It may be easier t
16. hten the nut on the mounting stud the locking nuts on the slide and the locknut on the adjustment bolt in that order Once you are sure everything is tight add the acorn nut to the mounting stud some blue Loctite here as shown below and tighten it securely against the first Give it a tug it should be very stout The left side should look like the picture below left If so you can install the other side the same way The right side 1s a bit tighter because of the exhaust We suggest a clean rag over the exhaust below where the leg mounts to avoid scratches and using a ratchet to EE tighten the mount bolts instead of a wrench right below 15 1999 amp EARLIER LEG MOUNTING Now we need to mount the Legs to the bike If your bike 1s a 2000 Up model please skip this section On 1999 and earlier Softail models the foot pegs are mounted to the bike using a 2 Allen bolts through the frame and into a threaded peg mount First we need to remove these pegs Using an Allen wrench as shown below hold the peg on a slight angle for leverage and loosen the Allen bolt and remove the pegs and the bolt Please find the Supplied 2 13 hex bolts and locking nut supplied Run the bolt through the lock washer you just removed the frame casting from the inside then through the leg and start the locking nut onto the bolt below The leg is fairly Ray heavy so you BI Next we need to get this bolt tight but
17. ical lengths On the right side of the bike press one end into the fitting on the back of the air cylinder These press in relatively easy but a small tug will make sure the line is seated Guide the line under the mount toward the front of the bike We need to use 2 wire ties to hold the line where we need it before it goes into the battery area Don t over tighten the wire ties Once in place manually push the leg down and allow it to retract a few times making sure the line stays away from the pipes Once you are sure the line 1s safe and not binding we need to guide it in front of the swingarm up through the oil tank to the area behind the battery As you can see in the picture the line has a nice easy bend to it While working with these lines we don t want to take any chances with them PME This line should be run behind the battery to join the left line as it 5 follows a path with the wire harness toward the back of the left saddlebag We want to attach the left line to the left cylinder and tie the wires off to that mount just like you did on the right side NEXT PAGE 18 Again run the leg up and down multiple times to make sure the line does not bind No exhaust on this side but the belt could eat through the hose in an instant Once you are sure the hose 1s clear we need to run it up behind the oil tank and join it with the other hose and ultimately tie it to the wire harness we installed on the fend
18. is warranty Replacement parts for this type of damage are available through Chopper Design Users of the LegUp system agree that Chopper Design is NOT responsible for personal injuries or damage to property arising from the use of the system While we believe this system to be safe and reliable the user is advised that use of LegUp is done so at the users own risk Use of the system implies agreement to the above statements If you can t agree with the above Chopper Design and its dealers would be happy to refund your full purchase price before you install the LegUp System Chopper Design Services 1365 Bennett Dr 101 Longwood FL 32750 407 834 5007 LegUp LandinGear com Installation Instructions The LegUp system has many components Please be sure you have them all before starting your installation COMPONENTS 1 Wire Harness W Switch Box 2 Leg and Mount Assembly L R 3 On board Computer Module 4 Proximity Sensor 5 Saddlebag Mounted Compressor System 6 Hardware Bag If you believe you are missing any parts please contact Chopper Design at 407 834 5007 and we will rectify the situation Some of the parts are shown below PREPARE FOR INSTALLATION IMPORTANT Harley Softails must be at STOCK height in order to install LegUp This system is designed to fit Heritage Softail models only While accommodations for other Softail models may be able to be made we can only guaranty fitment to the STOCK Heritage mod
19. just before the right assures that air 1s not released The top LED should now be blinking Press and hold the right button to raise the legs Listen as the air evacuates once it 1s quiet let go of the right button The UP stop is now set Hit both buttons when complete Both LEDs should light and you are done with these adjustment Now press the left button and the legs should lower again this is fast and loud The bike should be held up firmly Hit it again and the legs should retract If you are satisfied with these limits you have successfully installed the LegUp System 26 WHEEL ADJUSTMENT The LegUp GEN II system is typically set up at the factory for the height of your bike The system is VERY height dependent If after testing the initial installation the bike does NOT feel stable the wheel system MAY need to be adjusted to the height of your bike AGAIN we normally ask at order time if your bike is at stock height and we set the system up for whatever height you have furnished us DO NOT make any changes unless the stability we expect is NOT present If you feel you need to adjust the height length of the wheel holders please read this ENTIRE section before starting the process If you need help please contact Chopper Design at 407 834 5007 If you are happy with how stable the bike feels you can skip this section and move on to a test ride If you are not sure a good test is to bring the wheels down put the kickstand do
20. lled Your existing rear pegs floorboards MUST be removed Now we need to mount the Legs to the bike First we need to remove your rear pegs Typically these pegs are mounted to the bike by a 50 TORX Bolt for 2000 Up Bikes or Allen bolts for earlier models If you have a 1999 or earlier bike please skip ahead to the next section 1999 Earlier Leg Mount You first must remove the peg from the mount bolt amp nut or stud amp clip then using a long TORX Bit Included for certain year models or an Allen wrench remove the bolt and the mount Next we are going to mount a stud to make installing the leg system easier Find a stud with 2 nuts mounted on the end left Insert the stud into the rear peg mount hole blue Loctite here and thread it in as far as it will go just snug We want to run this in so we can mount a lock washer and nut on the back of this stud Once EE you start it in by hand you can use a wrench on the outer nut to drive it all the way in below Once this is installed we want to put a lock washer and a nut on the back of the stud sticking out behind the frame casting To make sure the nut is as tight as it can be hold the nut on the outside of the casting and tighten the nut you just installed right Mounting this properly and making sure it 1s tight is critical take your time here Once you have the stud tight we need to remove the outer nuts for the time being We do this by p
21. not completely tight Looking at the picture below use a 4 socket no extension it won t fit and a 34 open end wrench Snug the bolt up most of the way The picture at right shows how the leg snuggles into the casting of the bike this must find its spot or the leg will be mounted crooked 16 Next we want to loosen if not done already the 2 lock bolts on the adjustment slide Left 2 Arrows you don t have to loosen them very much The slide just needs to be able to slide a bit in its slot Find the adjustment bolt Right Arrow and tighten it until the slide 1s held firmly against the frame casting The purpose is to keep the entire system from pivoting so tug on the leg and make sure it can t move Double check everything is lined up properly then tighten the nut on the mounting stud the locking nuts on the slide and the locknut on the adjustment bolt in that order Once you are sure everything is tight final tighten the lock nut that holds the leg to the bike Give it a tug it should be very stout The left side should look like the picture below right If so you can install the other side the same way The right side is a bit tighter because of the exhaust We suggest a clean rag over the exhaust below where the leg mounts to avoid scratches 17 RUNNING AIR LINES We need to route the air lines from the cylinders to the area near the left saddlebag You should find 2 long air lines of ident
22. o plan you should have all plug connectors under the seat plugged to their matching plus the positive battery lead with fuse holder should be connected to the positive battery terminal there should be a hoop connector near the negative battery terminal and on the left side you should have two big plugs waiting for a home and the proximity bracket and sensor with no place to go quite yet JEU 2 a GR WT a i E we 11 Next we need to secure the wires that go into the saddlebag to the left fender rail and leave enough wire for the plugs to reach the computer and the compressor What we want to do here is take two wire ties and carefully thread them between the fender strut and fender as shown on previous page Run the wire under the chrome fender support and tie it off to the two fender supports Make sure you have 16 inches of wire sticking out from the end of the saddlebag rail and that the wire 1s tight to the support You can now pull the extra wire back into the under seat area Later we will be securing air lines to this wire so make sure that will be possible with your choice of how to attach this wire The only wires left dangling should be the 2 big plugs at the back and the proximity sensor and mount which we will handle soon 12 LEG amp MOUNT ASSEMBLIES IMPORTANT The GEN II LegUp system replaces your rear foot pegs We will ship your system with Touring bike style floorboards insta
23. o remove the plug end and tape the silver plug ends together for this We have some pictures below to give you an idea of what this looks like On some bikes it 1s easier to loosen or remove some of the tank mounting bolts Make sure the wires do not interfere with anything under the tank and that there is nothing that would scuff the wires Once the wires are under the seat area you can assemble the plug 1f disassembled according to the diagram above WIRING HARNESS 5 The harness and the plugs are routed mostly under the seat Different models have different amounts of space in this area and all the wires are long enough to allow you to place the connectors in the best place for your bike What you need to dois get the eight pin plug and the double white plug from the harness to the area under the seat The large 12 place plug and the connected 8 Pin plug attach to the Computer and Compressor respectively and they need to land near the left saddlebag Push the 12 pin 8 pin wire through the hole shown here between the fender support and the rear fender We are going to tie this wire up under the fender support so pull most all of the slack toward the back of the bike until you have 16 of wire past the end of the fender support as shown below 10 Find the proximity sensor and its three pin plug Run the wire plug first through the same spot you ran the 2 plugs through but from the fender into the area under the
24. seat so you can plug the 3 pin plug into its mate under the seat Leave the sensor and its mount dangling for now it will be mounted later We need to find the fuse holder and the black wire with the hoop ends on the harness and get them to the battery These two wires run direct power to the compressor when it needs it This wire should already be under the seat area We want to connect the wire with the fuse holder to the positive terminal of the battery the battery cable should attach closest to the battery with this connector and any others attached after t arr the battery cable as shown here Plan a mA where you want the fuse holder so you can get to it if it is ever required Don t connect the black wire to the negative post yet We will when we are ready to test the system Depending on the year of your bike it may look very different than the picture here this 1s with everything already buttoned up Let s plug some things together Disconnect the black fender plug under the seat and plug the double white plug in between the plugs from the bike If you have trouble finding the fender plug look for the wires coming from the back fender you should follow that to a black plastic plug that 1s the same size as the double white plug from the harness Connect the Control Switch Box plug to its mating connector under the seat and plug the proximity sensor plug 3 pin to its matching connector If everything went according t
25. support as described in the regular instructions so 1t can wind up in the saddlebag Along with this attach the thin wire from upgrade harness that has 2 hoop connectors on it to the fender support and get that wire to the battery The existing 12 pin plug and most of the upgrade harness will be tucked in the bag behind the compressor with the extra air line These are only suggestions run the wires anyway you like your existing connections to power will remain as they are One caveat 1s that the plug that used to run to the actuator will have no plug in it This should not be a problem assuming it is stored in an area that does not get very Wet When reading the install manual you should be able to ignore most all instructions having to do with wiring and you will NOT need to do the proximity test by rolling the bike as this should remain mounted If you have any trouble with this upgrade please give us a call at 407 834 5007 202 PRE 1996 WIRING ADDENDUM On bikes older than 1996 the plug for the fender wiring cannot be used as it 1s on other models Our wiring harness will have two wires where the white plug would normally be These two wires will be orange and black The orange wire MUST be hooked up to something that turns on and off with the bike Usually a wire that is blue or more preferably orange or orange with a white stripe is safe We recommend you find what you wish to use test it and cut solder and heat shrink the wir
26. u 27 This picture at right shows the tools we have at our disposal to adjust the wheels if needed The big bolt 2 can be placed in 2 positions the small bolts 3 we have 2 of these can be used to rotate the wheel holder a bit and the axle 1 can be placed in 2 different positions Another option you have which will shorten the leg length is to remove the wheel holder axle and 2 small bolts out turn it over and install it on the other side of the bike This keeps the wheels in the correct position and avoids you having to remove the wheels and turn them around as well If the bike with its normal passenger load is not stable enough with the wheels down or it drops more than 42 E RE de when transitioning from wheels down to dk up you may wish to re some vmi adjustments using the above tools Whatever you do try to keep the wheel holder under the leg when the legs are extended as much as possible Rotating the wheel holder too far back lends leverage and makes the system much less stable As we have said before the system should be close if not perfect the way we send it to you Shock condition and bike loading are the two main reasons you may wish to make these adjustments In many cases you can contact us and send us a picture with the wheels down and rider s up and we can recommend what changes to make to get the system the BEST it can be for you Be patient and call us for help if you are having any troubl
27. uld try to deploy the wheels As you come to a stop the Green LED should be on As you slow down almost stopped the Yellow LED should illuminate at the proper speed Once it does sometimes hard to see hit the left button and put your feet down near the ground The top LED should flash and the wheels should deploy almost instantly underneath you Make sure you are ready to balance the bike though you likely won t have to Immediately after the wheels touch the ground the bike should be supported reasonably but the cylinders can take up to 6 seconds to get completely filled Make sure you balance the bike as this occurs The slower you are going when deploying the wheels the smoother the transition will be from wheels up to wheels down Practice these maneuvers until you are comfortable with the wheel adjustments and the system operation SEMI AUTOMATIC DEPLOYMENT Another way to deploy the legs is semi automatically First we must be SURE that the proximity sensor is working properly or the wheels could come down at higher speeds than we wish If you are travelling at a speed over 10 MPH AND the yellow light bottom on the handlebar control is out hit the left button The bottom or yellow LED should start to flash When you slow down to around 5MPH the wheels will deploy see the red green flash on top LED Again prepare to put your feet down IF the lower LED 1s lit at a speed over 10 MPH don t hit that button see caution below NOTE T
28. utting one wrench on the outer nut and another on the inner nut as shown on the next page 13 The outer nut 1s loosened while the inner one 1s held firmly Remove the outer nut completely and then you can loosen and remove the inner nut Once the nuts are removed set them aside for now the stud should look like the picture below Do the same thing on the other side of the bike Now we can move on to installing the legs on the studs we have just installed MOUNT The Legs Find the appropriate leg for the side of the bike you are working on and slide it onto the stud you just installed Place a lock washer then the first of 2 nuts on the stud and start tightening this nut You will notice that as the leg draws nearer to the bike the bottom point of the leg mount needs to fit up against the frame casting as seen below We want to tighten this nut most of the way but need to make sure that you can pivot the leg on its mounting stud just slightly 14 Next we want to loosen if not done already the 2 lock bolts on the adjustment slide Left 2 Arrows you don t have to loosen them very much The slide just needs to be able to slide a bit in its slot Find the adjustment bolt Right Arrow and tighten it until the slide is held firmly against the frame casting The purpose is to keep the entire system from pivoting so tug on the leg and make sure it can t move Double check everything is lined up properly then tig
29. when they are down we recommend not trying to push with your feet to move the bike forward Use the engine and keep your feet out of the way this way the legs don t bite at your heels as the floorboard always have Backing up using your feet works fine and the chore of balancing the bike 1s taken care of for you Practice practice practice Enjoy your LegUp System 3 GENERATION I UPGRADE INSTRUCTIONS NOTE Read this before starting your installation if this is an upgrade If you are upgrading from a Generation I system most all the instructions in this manual pertain to you but some do not The most important thing is to NOT take your wiring harness off the bike We should have supplied you with an upgrade harness that will allow you to keep most everything as it was and adapt the wiring to the new system The second VERY important thing is that your computer MUST be sent in for upgrading or it will not work with the new Generation II system With those facts in hand let s get to it We will assume you have already removed all your Gen I hardware The legs the actuator mounts the mounting plate All you should have left from the old system is the wiring harness The upgrade harness plugs into where the old computer plugged in This 1s a 12 pin plug on the opposite end of the upgrade harness from the two plugs that are close together Once this is plugged in you should attach the harness with the 12 pin harness to the fender
30. wn and lean or try to the bike on its kickstand while sitting on the bike If you can t lean it onto the kickstand without significant effort you should not touch it move on to the next section Test Ride the wheel settings are fine The stability of the GEN II LegUp system relies on the pneumatic actuator when deployed being at an angle that 1s forward of perpendicular for best results Different bikes are at different heights and Chopper Design uses an ingenious method to adjust the length of the supporting legs to maximize the stability it affords Typically we will send the Leg Assemblies set up for the bike you told us you had We have three different Standard setups for the Harley Touring bikes Standard FL Height Street Glide and other bikes using the Harley lowered shocks and the new Ultra Low models The Softail setup 1s just a bit lower than the standard touring bike The first picture above shows the setup for standard height Softails The wheel holder is set with the strap facing up and the small bolts set 1n the 3rd and 5th hole from the back of the leg Notice curve of wheel holder with the bolt in the second hole on the wheel holder wheel rotates a bit extra toward the back The axles are set in the higher of the two holes on the wheel holder I know this sounds confusing but it 1s all part of the fine tuning of the height of length of the legs This is how we should have sent the legs to yo
Download Pdf Manuals
Related Search