English user manual
Contents
1. possibility to move around on its own This user manual is a guide to assist in gaining the full benefits of the options of fered by the Rabbit Therefore we recommend you read this manual before using the mobile standing frame SAFETY The Rabbit has earned the CE mark This certifies that it meets all relevant Euro pean safety requirements The durability of this product is 5 years when it is used on a daily basis Hereafter we recommend that the product should be renovated by R82 personnel to extend the lifetime Remove the CE mark when re building the product or when using other than original R82 spare parts and fittings Never leave your child unattended in this product Ensure permanent super vision by an adult Incorrect use of the Bronco may cause serious injury on the user Take care that all the fixations and adjustments are placed and fitted correctly and check it on a regular basis A Use only when all 6 wheels are mounted GUARANTEE Any R82 product bought with an R82 dealer includes a guarantee against de fects in types and materials There is a 5 years guarantee on frame breaks The guarantee is given by the R82 dealer or subsequent R82 representative The guarantee can only be sustained if the R82 product is in use in the same country as produced for The guarantee does not cover accidental damages including damages caused by misuse or neglect The guarantee stops if the serial number is remov2. the centre bar Mount the fitting from the hip support on the top bolts Mount bolts B in the lower square plates Move the bolts and plates upwards until they fit into the fitting from the hip support Fasten all bolts securely using the enclosed 6 mm allen key Fasten the fingerscrew C Loosen the handle D and E to adjust the hip supports in depth Fasten the handles in the desired position Lock the handle D making sure the pin lock F is released Loosen the handle G to adjust the hip sup port in height Use the enclosed 6 mm allen key to loosen the bolts H and adjust the supports individually in height and width not possible for size 1 Make sure the fingerscrew C is fastened before use HIP SUPPORT FRONT Follow the description below to mount the hip support correctly Mount the two square plates in the slots on both sides of the centre bar Mount bolts A in the upper square plates and fasten slightly Do not fasten completly before the four bolts have been placed correctly Mount bolts B in the lower square plates Move the bolts A B and plates upwards until they fit into the fitting from the hip sup port Now fasten all four bolts securely using the enclosed 6 mm allen key Loosen the bolts C and adjust the hip sup ports in depth Fasten the bolts in the desired position HIP SUPPORTS DE ROTATION Follow the description below to mount the hip suppo
3. 0 0 0 0 O0 9 9 O 0 9 9 O 9 0 O GO 0 0 O 0 ee HINGED KNEE SUPPORTS Follow the description below to mount the hin ged knee supports correctly The knee supports are mounted seperately and can be adjusted individually The square plates on the knee support is mounted in the slot on the centre bar Adjust the knee support in to the desired height and fasten A using the enclosed 6 mm allen key Make sure that the fitting B is in vertical position when the knee support is mounted not for size 1 Loosen the screw C and adjust the angle of the foot support Fasten in the desired position Loosen the screw D to angle the support around the knee Use the enclosed 5 mm allen key Loosen the screw E and adjust the knee supports sidewise EXTRA CUSHION Move the cushions on the chest support or the hip support to the side by loosening the bolts A and make room for the extra cushion Place the extra cushion in the middle between the cushions and tighten the bolts A and B Can be mounted on the chest support and hip supports size 2 and 3 HIP SUPPORT REAR Follow the description below to mount the hip support correctly Mounttwo square plates in the slots on both sides of the centre bar Mount bolts A in the upper square plates and fasten at the desired height using the enclosed 6 mm allen key Be aware that the height of the top square plates is the same on both sides of
4. 020290900209290020290992990 CHEST SUPPORT We recommend to mount the chest support as the final equipment Follow the description below to mount the chest support correctly Mountthe top part A in the top of the centre bar and fasten with the enclosed 5 mm allen key Mount the chest support in the hole in the centre bar and fasten with the handle B Loosen the screws C and adjust the chest support sidewise and in height Fasten all screws in the desired position Max height D The max height indication on the chest support bar must not go higher than the top of the centre bar not the top of any extra bars from e g the tray ABDOMINAL SUPPORT Follow the description below to mount the ab dominal support correctly Mount the two square plates in the slots on both sides of the centre bar Mount bolts A in the upper square plates and fasten slightly Do not fasten completly before the four bolts have been placed correctly Mount bolts B in the lower square plates Move the bolts A B and plates upwards until they fit into the fitting from the abdominal support Now fasten all four bolts securely using the enclosed 6 mm allen key 0 9 6 0 6 9 06 0 0 9 0 0 9 09 0 0 9 9 O 9 9 0 O 0 0 O 0 0 0 o 0 0 GO 0 0 O 9 9 0 0 0 0 0 O 9 0 GO 9 9 0 GO 0 6 0 O 9 06 O0 0 9 0 0 0 9 O 0 9 9 O GO 9 0 O GO 9 0 O 0 06 0 6 9 09 0 9 9 Er Er Er Er Er o PRODUCT IDENTIFICATION A
5. 40 5 Ib 70 kg 154 Ib TECHNICAL DATA Frame Powder laquered aluminium tubes Plastic parts Fibre glass strengthened nylon Upholstery PUR Polyurethane PRODUCER DISTRIBUTOR R82 A S Parallelvej 3 8 51 Gedved Denmark Please find your distributor on www r82 com CARE AND MAINTENANCE PUR All parts made of PU material must be wiped off with a cloth frequently WHEELS BRAKES Ball bearings The ball bearings require no maintenance Clean the wheels frequently to make them run more smoothly and make the brakes function optimally NO lubricating oil is required around the brakes Wheels that are worn out must be replaced Check the tyres regularly for air Air presure 110 PSI 7 5 bar 750 kPa 36 PSI 3 5 bar 350 kPa SPOKES Regularly the spokes need to be adjusted by an expert For instance by your local bicycle engi neer HAND RIMS If a handrim should be damaged in such a way that it could lead to hand injury it should be re placed FRAME Tighten all screws on the frame on a regular basis especially when the Rabbit has been adjusted Also it is important to keep the frame clean both for the users comfort and the longevity of the standing frame Wash the frame with car shampoo or dishwashing liquid Do not use any cleaning materials containing chlorine or methylated spirit If the Rabbit is especially dirty a grease remover may be used INSPECTION It is important to tighten all screws on the standing frame o
6. Rec e TM rabbit 2007 R82 A S All rights reserved The R82 logo and the Rabbit are trademarks of R82 A S 07 2007 eri 4 EIE RINT ETIN 4 jJ P 4 Rice Aog 5 Angling of the centre bar coocccocccocncocncccnoconocaninoninonoss 6 DIOS Su uer b bI ee o ERU ENIMS EVE aU 6 Height adjustment of driving wheels T Mounting and adjustment of the foot plate 8 Mounting and adjustment of individual foot supports 9 Spoke protectors nen rare aan LT SNR SUUM E LUN 9 Mounting of flip up sandals heel supports 10 Hee SUDDOTIS cestas 10 Hinged knee SUDOR Senasa nata 11 EXIT CUS MO Marinero 11 FD SUDBOFE ors ee 12 FO SUDDO TONE a OOPS 13 Hip supports de rotation occoccoccconconcoccocncanioconnonanons 13 FI AG SU DOM rare age ee a en 14 Tray ana Py Dee ea 15 Extension for centre bar 8 CM ccccececececeecececececeeeeeees 15 IS SE SUDDOPI een 16 ADBAOmINalSUDDO Messina eee 16 Product identification een 17 WIC A EU ge 1415 y 1 e een 18 TECNICA dala NETT 19 PLOT oo ii PE e 19 Bugs O PR oi II A 19 Care and maintenance cooccccccccncoccconcocnconncanononconncanonons 20 jeep T ea 21 Pat pend RABBIT The Rabbit is a mobile standing frame providing users the possibility of standing and also gaining the
7. Serial number The label is placed on the front bar to the left B Manufacturer The label is placed on the lower part of the frame near the left rear caster Dato 31 01 02 Belast kg SN 0840 01 111878 001 Varenr 880003 nr 5707292 134158 RBe c Parallelvej 3 DK 8751 Gedved MEASUREMENTS Length frame L Length total Width W Size 1 cm inch 62 244 62 244 61 24 Height from floor Frame in heighest position H1 100 39 Height from floor Frame in lowest position H1 Height from foot plate Frame in h position H2 Height from foot plate Frame in position H2 Height floor to foot plate Angle of the centre bar A1 Angle of the foot plate A2 Centre bar Camper Weight Max load user weight 67 26 90 35 57 22 6 2 0 to 30 15 to 10 50 19 5 go 13 5 kg 29 5 Ib 40 kg 88 Ib Size 2 cm inch 75 29 4 75 29 4 68 2672 118 46 85 3374 108 42 75 29 4 6 272 O til 30 15 til 10 70 2772 4 15 5 kg 34 Ib 90 kg 110 Ib Size 3 cm inch 75 29 80 3114 68 2614 131 51 99 3814 119 46 86 3314 6 272 O Til 30 15 til 10 80 3114 4 16 kg 35 Ib 60 kg 132 Ib Size 4 cm inch 85 33 90 35 70 27 153 59 120 46 139 54 4 106 4174 6 272 O til 30 15 til 10 100 39 4 18 5 kg
8. e eee eee eee ee eee eee ee seeeeseeeeeeeeeeseeeeeeZeeeeeeeeseeeeeZeeeeee ee ooo Eo Hoo EHH HHO HOH OHO HHO ne e oe ee OHH O EEO oe OS ANGLING OF THE CENTRE BAR The angle of the centre bar standing frame is adjustable either with or without a user in the Rabbit Pull out the security lock A to be able to angle the centre bar standing frame Turn the handle B to desired angle Let go of the security lock A to maintain the desired position BRAKES Brakes are mounted on the Rabbit on both sides of the frame Pull up the handle A to activate the brake The brakes are used during transportation or when the child is standing still playing maybe with a tray play box mounted The brake can be adjusted to brake either more or less Turn the cable tightener B with the clock to brake less and against the clock to brake more Fasten the lock nut C to maintain the desired position We recommend not to lock the wheels if the Rabbit for any reason is not used for a longer period HEIGHT ADJUSTMENT OF DRIVING WHEELS The height of the driving wheels can be adjusted to fit the desired height to floor on the small casters The Rabbit is delivered with max 1 cm height to floor on the casters Follow the description below to adjust the height on the driving wheels Dismount the driving wheels Dismount the drum brake A using a 3 mm Allen key and 8 mm wrench Dismount
9. ed or if the product is repaired or changed by other than authorized R82 staff TOOLS Tools are delivered with the Rabbit 5 4 6 mm allenkey This key is used to perform some of the adjustments described in this manual READY FOR USE The Rabbit is delivered without accessories to make it take up as little room as possible during transportation To assemble your Rabbit ready for use please follow the description below rable ed lf xj H 7 er Nr in j ity td 1 A Remove the Rabbit from the packaging Check if all tires run smoothly Check if the brakes work correctly See another page in this manual to adjust the brakes The brake handles on both sides of the centre bar has to be removed to be able to mount vari ous accessories Follow the below description Loosen the screw A using the enclosed 5 mm Allen key Move the brake handles upwards and dis mount from the centre bar Mount the desired accessories and remount the brake handles Fasten with the Allen key The Rabbit is now ready for use and to receive any accessories ordered Do not place an user in the Rabbit if it has been standing in exposed to sun For the safety and comfort of the user the Rabbit must be moved away from the sun and chilled before use Before mounting the accessories we advise removing the driving wheels AN Do not use without the driving wheels eoeeeec eee eee cere eee eee eee eee eee ee
10. led This product is multi adjustable and must only be set by autorised personnel e g therapists The user may experience several of these problems in a standing frame that is incorrectly ad justed or is being used incorrectly 21
11. n a regular basis All screws which secure the accessories must be checked at least once a month To avoid sharp edges it is important to check all rail ends have end caps Also it is important to be aware of any cracks or faults in the frame PVC parts etc REPAIR If there is a problem with your Rabbit you should contact your dealer at once Defective frames should not be used If your standing frame need reconditioning or repair only original R82 parts may be used Accessories or available spare parts which are broken can be forward ed to R82 for repair If there is a problem with any basic parts the whole frame must be returned to R82 for repair R82 will not be held responsible for damage or injury caused by use of non original parts or repairs made by a non authorised R82 person 20 eeoeeecec reece eee eee eee eee eee Tee TROUBLESHOOTING Problem The Rabbit is hard to move push turn The spindel is not working The product seem loose The brakes do not function correct Solution Check that all brakes have been released Check if all front forks are turnable If not contact youres dealer Checkifthe security lock has been released If the spindle still not work contact your dealer Check if all screws and bolts hasve been fastened securely Adjust the distance between the tires and the brake Loosen or tighten the cables until the brakes work correct and it is possible to turn the wheel untroub
12. oosen the screw E to angle the head sup port Loosen the screw F to adjust the head support sidewise TRAY AND PLAY BOX Follow the description below to mount the tray play box correctly Loosen the handle A and dismount the chest support Mount the tray on the chest support bar and fasten in the desired height with the enclosed 4 mm Allen key B Place the chest support bar in the centre bar and fasten with the handle A Loosen the handle C to angle adjust the tray play box Fasten in the desired position Use the enclosed 4 mm Allen key to adjust the depth of the tray play box The tray is also a lit for the play box and is easily lifted EXTENSION FOR CENTRE BAR 8 CM Follow the description below to mount an exten sion on the centre bar To be able to mount the extension part and the centre bar all the together the plast hubs needs to be dismounted Use the 5 mm Allen key to dismount the hubs Accessories can now be mounted in both the centre bar and the extension part Mount the chest support bar from the top and down through the extension part and the centre bar Fasten with the handles A 15 060920920620290206062060206206202062962020602906206020290202020602920602020602020202902090202060206020206020202029029202029202020929020202029020209202020292020292292920290929020929202902029292922092929020290929292909202929029290290294929290292929292029202920929290920202920202092920202929202029002029
13. rts de rotation correctly Dismount the two fittings A from the de ro tational hip supports Mount the fittings on both sides of the centre bar Fasten the screws B in the desired position The possiblity of rotational adjust is available before the screws are fastened completely Mount the hip support on the fitting C Fasten in the desired angle Loosen the screws D to adjust the hip sup port sidewise and in height Fasten all screws in the desired position 13 X 4 EA 2 fl 2 u i E dr 06092020620206206206206020620620206296206020602062062029602062020292060202062920602029202020206020202092060202902020202920202092909020202020202092092902942929202922929202029029029420290209292029229092920202090292092902029020902920202292929029209292292029202929029290920920292020292920202902020206020602029006020902902902020902902029099299 0 HEAD SUPPORT Follow the description below to mount the head support correctly Either back support or hip supports rear must be mounted to be able to mount a head support on the Toucan Mountthe head support bar on the fitting from the back support hip supports rear and fa sten with the enclosed 4 mm Allen key A Loosen the handle B to adjust the angle of the head support bar Loosen the handle C to adjust the height of the head support Use the enclosed 5 mm Allen key to loosen the screws D and adjust the head support L
14. t B and the 6 mm Allen key Turn the handle C to angle adjust the foot plate Loosen the bolts B in both sides of the centre bar and height adjust the foot plate Fasten the bolts in the desired position 6 9 6 0 0 9 06 0 0 9 0 0 0 09 0 0 0 9 O 0 0 09 O0 0 9 0 O 0 0 6 O 0 0 O0 0 09 0 O 9 9 0 O0 0 9 0 O 9 0 GO 9 9 0 GO 9 6 0 O 9 06 0 0 0 0 0 0 O 0 9 9 O0 0 9 0 O 0 0 0 O 0 ee MOUNTING AND ADJUSTMENT OF INDIVIDUAL FOOT SUPPORTS Follow the description below to mount the foot supports correctly The foot supports are mounted seperately and can be adjusted indi vidually The square plates mounted on the foot sup port should be mounted in the slot on the centre bar as for the foot plate Adjust the height and fasten the screw A using the 6 mm Allen key Tip In general we recommend to mount all acces sories from the top of the centre bar which is why the lower accessories must be mounted first Loosen the screws B to adjust the height and angle of the foot supports Adjust the foot plate sidewise C and in depth D Loosen the screws E to adjust the angle of the foot plate Make sure to fasten the screws D and E in the re commend order 1 2 3 Make sure that all screws are fastened securely before use SPOKE PROTECTORS Follow the description below to mount spoke protectors on the Combi Frame 1 Place the protector on the spokes 2 Mount the enclosed clips through the holes in
15. the spoke protectors and click into place on the spokes eoeee eee eee eee eee eee eee eee eee eee eee eee eee eee eee eee eee e eo o eo oo o o o o eo noe oo n oe o noe eo Heo no HOO HE HO ooo no nen HOHE eo eo e OEE OEE eS MOUNTING OF FLIP UP SANDALS HEEL SUPPORTS Follow the description below to mount the flip up sandals heel supports correctly Place the enclosed bolt A in the slot from the top of the footplate heel support and fasten with the fingerscrew B The flip up sandal heel support can be ad justed forward or and backward depending on the desired placement C Fasten the screw beneath the foot plate in the desired position KNEE SUPPORTS Follow the description below to mount the knee supports correctly The knee supports are mounted seperately and can be adjusted individually The square plates on the knee support is mounted in the slot on the centre bar Adjust the knee support in too the desired height and fasten A using the enclosed 6 mm allen key Make sure that the fitting B is in the vertical position when the knee support is mounted not for size 1 Loosenthe screw C and adjust the angle of the foot support Fasten in the desired position Loosen the screw D and adjust the knee supports sidewise 6 9 6 06 6 9 06 0 0 9 0 0 9 09 0 0 0 9 O 0 0 0 O0 0 9 0 O 0 0 0 O 0 0 GO 9 0 O 9 9 0 0 0 0 0 O 0 O0 9 9 0 GO 9 6 0 O 9 0 O
16. the wheel suspention B using a 17 and 24 mm wrench Mount the small plate C in the desired position Mount bolts and nuts as shown on the drawing Fasten with a 17 and 24 mm wrench Fasten the lock nut D with a 24 mm wrench Please be aware that the small plate C is mounted at the same height on both sides of the frame Further the small dent in the plate must be either up or down in both sides Mount the drum brake E in the holes in the plate depending on where the wheel suspen sion is mounted Use a 3 mm Allen key and a 8 mm wrench to mount the drum brake Mount bolts washers and nuts as shown on the drawing Please be aware that the heigh to floor on the small casters not exceed 15 mm 0 9 0 6 0 9 0 GO 9 6 O0 0 9 06 O 0 9 0 9 9 0 GO 9 9 O 0 9 0 O 0 0 0 0 9 O 0 0 0 O 0 0 0 O 0 O GO 9 0 O 0 9 0 O 0 0 0 O 0 0 O0 9 9 O 0 0 0 O 0 0 0 0 0 0 0 9 09 O 9 9 0 O 9 6 0 0 09 Eee 0 GO 9 06 0 0 6 6 6 oo MOUNTING AND ADJUSTMENT OF THE FOOT PLATE Follow the description below to mount the foot plate correctly We recommend to dismount the square plates from the foot plate before mounting Tip In general we recommend to mount all acces sories from the top of the centre bar which is why the lower accessories must be mounted first The square plates A from the foot plate is mounted in the slots on the centre bar Let them slide all the way down Mount the foot plate using the enclosed bol
Download Pdf Manuals
Related Search