Automatic Barrier Gate Opener System
Contents
1. Quanzhou Giant Alarm System Co LTD MI Tel No 86 595 22499516 Fax No 86 595 22492516 hn Email autogate02 jujiang net cn JUJIANG Website www cngiant net Automatic Barrier Gate Opener System Installer and User s Manual IN Automatic Barrier Gate Opener System is designed for vehicular traffic only CAUTION Automatic Barrier Gate Opener System is powerful while working It may cause seriously body injury or death to pedestrians if they walk through around the automatic barrier inappropriately Should have other separate walkway for pedestrians Every time must cut off power supply before starting installation operation or maintenance 2 The Automatic Barrier System should be earthed and earth leakage breaker is necessary in power supply 3 Do not change the inside wirings 4 If power cut occurs please switch off the power supply at first then opening door of cabinet to open or close the barrier manually by rotating the handle 5 The balance of the boom and spring already been well adjusted to optimum before out of the factory If it is not necessary do not add the length or weight of boom in case of dangers occurred If the adjusting in necessary please ask your local dealers or installers 6 All limit switches both mechanical limit switch and photoelectric limit switch already been well adjusted to optimum Do not adjust any limit switch unless it 1s necessary 7 Keep the wireless control2. lt D O O y gt O jZ a a lo O m O m gt O U Z ys a jm m e ES amp e OU 5 gt e e P2 Transformer 5 Receiver Module Pluger Code Learning Button 6 3A Fuse Working Times Potentiometer 7 External Push Button Pluger Jumper for motor reverse function 8 Antenna Terminal 6 Upwards Limitswitn SSS JUJIANG Quanzhou Giant Alarm System Co LTD TA Tel No 86 595 22499516 Fax No 86 595 22492516 a Email autogate02 jujiang net cn Website www cngiant net 7 Transmitters code setting 7 1 Transmitter programmed Press Code Learning button the code learning LED indicator lights up then press any button of the transmitters which you are going it program till the code learning LED indicator goes off Now the transmitter programmed Other transmitters can be programmed as same as this way It can program up to 30 transmitters 7 2 Transmitters code removing Press and hold code learning button for 5 seconds the code learning LED flashes 5 times all the programmed transmitters removed 7 3 Working Mode Switching o O CI LO LL MODE COM DOWN UP It refers to when you use wireless remote control to operate the barrier gate There are two types of working mode three buttons working mode or single button working mode In the three buttons working mode for example button A operates open button B operates stop and button C ope
3. ching the delay time which set earlier The delay time can be set from 1 99 seconds 9 Trouble Shooting 1 Check the motor wiring connection is 1 Check the motor wiring is correct or not strong and reliable 2 Check each limit connection is 2 Correct wiring connection correct or not from motor to control panel is 3 Check the capacitor connect up or red UP white COM yellow Motor works but not DOWN Limit wiring black boom do not work COM orange DOWN green UP red SVDC 3 Connect two capacitor wirings with motor wirings for up and down l Please replace spring according spring list and adjust 1 Spring is out of balance Boom vibrates too spring in a best level 2 Boom screws is loose much during falling 2 Fasten screws in the boom 3 Barrier house do not been fixed well 3 Fasten fang bolt for fixing barrier house 1 Check the limit wire then Boom stops in the 1 Not adjust limit switch well connect in a right place and middle during falling 2 Spring is out of force adjust limit switch 11 Quanzhou Giant Alarm System Co LTD MI Tel No 86 595 22499516 Fax No 86 595 22492516 hn Email autogate02 jujiang net cn JUJIANG Without anti break Boom is not in vertical or horizontal level when up and down Website www cngiant net Loop detector and photocell broken or no connection in a right place Not adjust the limit well 12 2 Replace spring or adjust sprin
4. g force Replace loop detector and photocell then connect the wire carefully according wiring diagram Make the boom in vertical or horizontal level then put the light barrier in the middle of the photoelectric limit switch since light is on during induction Boom is down in place when Red light is on and up in place when green light is on
5. ig9 Fig10 The boom will go downwards after it becomes longer Please note that our standard spring is optimum for length of boom from 5M 6M As the maximum length of the boom is 6M so this situation may not occur Installer or user can add the value of spring according if it is necessary PES PES A oa 7 SS Fig 9 Also can do the fine tuning to tune the verticle or horizontal of the boom Nut Quanzhou Giant Alarm System Co LTD TA Tel No 86 595 22499516 Fax No 86 595 22492516 a Email autogate02 jujiang net cn JUJIANG Website www cngiant net 6 Wiring and Adjusting Electrical Part Caution Always cut off the power before doing any wiring or adjusting in electrical part 6 1 Wiring For Control Panel TOOT OO 300N NMOQd OGAS 90AZ dOLS 380719 N3dO OJTAVI NI C220VAC CAP ALARM LAMP P1 P2 Transformer 5 Receiver Module Pluger 2 Code Learning Button 6 6 3A Fuse 3 Working Times Potentiometer 7 External Push Button Pluger 4 Jumper for motor reverse function 8 Antenna Terminal Quanzhou Giant Alarm System Co LTD ie Tel No 86 595 224995 16 Fax No 86 595 224925 16 a Email autogate02 jujiang net cn JUJIANG Website www cngiant net G A m m va 220VAC ICAP ALARM LANP lt O O E O gt O 0 O O O O O U
6. lectric limit switch already been well adjusted to optimum It can be adjusted by manually turning the limit leaf blade PS Limit Switch Limit Blade Fig 5 4 Adjust Spring Fig 6 If the boom is shaking while if it falling down use the wrench to tighten the nut of spring if the boom is shaking while rising up use the wrench to loosen the nut of spring EI a m Ap a Ta m EEG PRD d i H EE AIN We Turning left to tighten the spring Adjusting Nut Fig 6 Turning right to loosen the spring Quanzhou Giant Alarm System Co LTD LF Tel No 86 595 224995 16 Fax No 86 595 224925 16 a Email autogate02 jujiang net cn JUJIANG Website www cngiant net 5 Adjust Vertical or Horizontal Of the Boom This already well adjusted to optimum before out of the factory But it has to be re adjusted if the length of the boom changed 5 1 Boom is shorter Fig 7 Fig 8 The boom will go upwards after it becomes shorter Please note that our standard spring is optmum for length of boom from 5M 6M If the length of boom becomes short the value of the spring should be decreased Fig 7 Also can do the fine tuning to tune the verticle or horizontal of the boom Quanzhou Giant Alarm System Co LTD LF Tel No 86 595 224995 16 Fax No 86 595 224925 16 a Email autogate02 jujiang net cn JUJIANG Website www cngiant net 5 2 Boom is longer F
7. rates close In the single button working mode there is only one button works cycle operation open stop close It can be switched as per users preferences by using wire to short circuit the terminal mode and com see fig about 5 seconds later the LED indicator flashes the working mode has been switched 8 Safety Devices Optional 8 1 Photocell When the gate is open if any objects or persons sensed in the sensing range of photocell the gates keep open status Quanzhou Giant Alarm System Co LTD Tel No 86 595 22499516 Fax No 86 595 22492516 173 g jujiang J ha Email autogate02 juj1ang net cn JUJIANG Website www cngiant net When the gate is close if any objects or persons sensed in the sensing range of photocell the gates will open immediately Oo 5VDC INFRARED 12V Emitter Receiver 8 2 Loop Detector If any objects or persons sensed in the sensing range the gate keeps open status After the objects or persons pass through the range of sensing range the gate will close Qda mam INFRARED 12V COM immediately Loop detector N 10 Quanzhou Giant Alarm System Co LTD MI Tel No 86 595 22499516 Fax No 86 595 22492516 hn Email autogate02 jujiang net cn JUJIANG Website www cngiant net Note If auto closing function is enabled when the objects or persons pass through sensing range the gate will close automatically after rea
8. system push button transmitters etc out of the reach of children 8 Use transmitters and push button to control the automatic barrier only when you can see the operation of the gate clearly 9 Do not open the door or cover of cabinet when the motor is working 10 Keep children away from the automatic barrier system Quanzhou Giant Alarm System Co LTD Tel No 86 595 22499516 s x Fax No 86 595 22492516 Email autogate02 jujiang net cn JUJIANG Website www cngiant net 1 Technical Specifications AC220V 10 50HZ 60HZ or AC110V 10 50HZ 60HZ 2 Installation and adjusting 2 1 Install the machine on the ground Fig 1 Cabinet xpansion bolt 4 M16 ON i O pe Base frame Expansion bolt Fig 1 2 2 Install boom Fig 2 Fig 3 uanzhou Giant Alarm System Co LTD e Q LF Tel No 86 595 224995 16 Fax No 86 595 224925 16 Email autogate02 jujiang net cn JUJIANG Website www cngiant net 2 3 Manually Operation when power cut occurs Fig 4 If power cut occurs please switch off the power supply at first then opening door of cabinet to open the barrier completely by rotating handle uanzhou Giant Alarm System Co LTD e Q S Tel No 86 595 22499516 Fax No 86 595 22492516 Email autogate02 jujiang net cn JUJIANG Website www cngiant net 3 Adjust the limit switch Fig 5 All limit switches both mechanical limit switch and photoe
Download Pdf Manuals
Related Search