User Manual
Contents
1. Visio touched o s j LED HANDY CON 101 LED HC101 User Manual Please read the instructions carefully before use a LED HC 101 TABLE OF CONTENTS Safety Instructions Technical Specifications Function Installation DMX512 Address setting How to control the fixture DMX 512 Connection Troubleshooting Fixture Cleaning LED HC 101 1 Safety Introductions Please read the instructions carefully which includes important information about the installation operation and WARNING maintenance e Please keep this User Manual for future consultation If you sell the fixture to another user be sure that they also receive this instruction booklet e Unpack and check carefully there is no transportation damage before using the fixture e Before operating ensure that the voltage and frequency of power supply match the power requirements of the fixture e Disconnect mains power before servicing and maintenance e In the event of serious operating problem stop using the fixture immediately Never try to repair the fixture by yourself Repairs carried out by unskilled people can lead to damage or malfunction Please contact the nearest authorized technical assistance center Always use the same type spare parts e Do not touch any wire during operation and there might be a hazard of electric shock e To prevent or reduce the risk of electrical shock or fire do no2. Tight the screws Set the switch to OFF the LED lights will go into standby mode set it ON the lights will revive LED HC 101 DMX DMX GND OV TTZV CAUTIONS the LED controller total output power consumption is 100 watt 5 DMX512 Address Setting Each fixture needs to have a start address set to receive the data sent by the controller The address number is between 0 511 usually O amp 1 are equal to 1 The address also know as the start channel is the first channel used to receive instructions from the controller There are four ways to set the fixture DMX start address A DMX address setting by dip switches B Auto DMX addressing C Remote DMX address setting by CA T DMX TESTER D Remote DMX address setting by universal DMX controller Visio uched by color LED HC 101 3 If you use the function B C or D to set the DMX start address the fixtures of the chain all DIP switch MUST be set to OFF 3 When you set the address by DMX controller and dip switch at the same time the order of the DMX controller will be invalid A DMX address setting by dip switches 1 Set the start address by dip switch as the diagram below 2 Hold the AUTO DMX ADDRESS button for about 5 seconds the LED lights blinking indicating the address is set successfully Ce ree eo re es eser so y 0 vaus 1 2 e re a2 e 120 256 assi Examples Channel 01 dip on 1 21 C
3. 16 B Control by universal DMX controller If you use a controller with 5 pins DMX connector you need to use a 5 to 3 pin Visio touched by color LED HC 101 adapter The fixture uses four channels Please refer to the following diagram to use your controller to activate the fixture DMX512 Configuration GREEN BLUE DIMMER STROBE 255 100 255 100 255 100 248 2551 OPEN AAA 204 247 Kr y SOUND 191 200 CHASE 0 0 0 0 0 0 C Master Slave operation The fixture will allow you to link 16 fixtures together and operate without a controller In Master Slave mode the first fixture will control the others to give an automatic sound activated synchronized light show This function is good when you want an instant show The first fixture it s DMX input cable will have nothing connect it and the other fixtures will be set in slave mode automatically Their DMX input cables Visio d touched by color LED HC 101 connect the last fixture DMX output cable daisy chain Any fixture can act as a Master or as a Slave 7 DMX512 Connection The DMX 512 is widely used in intelligent lighting control with a maximum of 512 channels COMMON e DMX e INPUT 30 3 OUTPUT e DMX e Termination reduces signal errors and to avoid signal transmission problems and interference It is always e advisable to connect a DMX terminal e Resistance 120 ohm 1 4W between pin2 DMX and T pin3 D
4. MX of the last fixture 1 If you using a controller with 5 pins DMX output you need to use a 5 to 3 pin adapter cable 2 Atlastunit the DMX cable has to be terminated with a terminator Solder a 120 ohm 1 4W resistor between pin 2 DMX and pin 3 DMX into a 3 pin XLR plug and plug it in the DMX output of the last unit 3 Connect the unit together in a daisy chain by XLR plug from the output of the unit to the input of the next unit The cable can not branched or split to a Y cable DMX 512 is a very high speed signal Inadequate or damaged cables soldered joints or corroded connectors can easily distort the signal and shut down the system 4 The DMX output and input connectors are pass through to maintain the DMX circuit when one of the units power is disconnected Visios 9 touched by color LED HC 101 5 Each lighting unit needs to have an address set to receive the data sent by the controller The address number is between 0 511 usually 0 amp 1 are equal to 1 The end of the DMX 512 system should be terminated to reduce signal errors 3 pin XLR connectors are more popular than 5 pin XLR 3 pin XLR Pin 1 GND Pin 2 Negative signal Pin 3 Positive signal 5 pin XLR Pin 1 GND Pin 2 Negative signal Pin 3 Positive signal 8 Troubleshooting Following are a few common problems that may occur during operation Here are some suggestions for easy troubleshooting A The fixture d
5. hannel 05 dip on 1 3 1 4 5 Channel 09 dip on 1 4 148 29 Channel 13 dip on 1 2 3 4 1 4 8 13 B Auto DMX addressing 1 The DMX address of fixture can be set automatically Set all dip switches to OFF and hold the AUTO DMX ADDRESS button of the first unit for about 5 seconds the fixture will be set the DMX start address to 1 and the other fixtures of the chain will be set their own DMX start address automatically 2 he LED fixtures use four channels the next fixture s will be automatic calculate their own DMX address not need to calculate the DMX channels of each fixture in the chain Fixture 1 1 Fixture 2 5 Fixture 3 9 Fixture 4 13 Fixture Visio T uched by col LED HC 101 3 No need to turn the fixture off when you change the DMX address as new DMX address setting will be effect at once Every time you turn the fixture on it will be ready to receive DMX signal or run the built in programs C Remote DMX address setting by CA T DMX TESTER The fixture can be set the DMX address remotely by CA T DMX TESTER Please refer to the CA T user manual to set the DMX address to the fixture DMX Tester PUNCTI DISPLAY ADORESS CHANNEL z LEVEL RANGE UL Fr LL D Remote DMX address setting by universal DMX controller e Make sure the DMX cables of all units are connected e Connect the first unit to a universal DMX control
6. ler e Connect all units to the mains so they are switched on e Set all DMX channels on your DMX controller to zero value 000 e Setthe DMX channel that you want to assign as DMX start address on you unit to maximum value 255 e Press the Auto DMX address button on the unit shortly e f you want to set another unit to the same DMX start address simply press it s Auto DMX address button and it will receive the same address e Done An example to make things clear Visio i touched by color LED HC 101 e Wewill set the DMX start address of a unit to 106 e Connect the unit to the DMX controller as described above and make sure all is switched on e Set all DMX channels on the controller to zero 000 e Now set DMX channel 106 to maximum 255 e Press the Auto DMX address button on the unit shortly e Done Your unit now has DMX address 106 6 How to control the fixture There are three ways to control the fixture A Control by DIP switches B Control by Universal DMX controller C Master Slave operation A Control by DIP switches ma oo LLLA ON 123456 7 8 9 10 LB LUUL ON12345678910 DO ON1234567 8 9 10 Chase ONT 234567991 Use Dip switch 3 4 5 to choose chase speed 1 8 il Fade ON 12345567 8 910 Use Dip switch 3 4 5 to choose fade speed 1 8 Color ON12345678 910 Use Dip switch 6 7 8 9 to choose color
7. oes not work 1 Check the connection of power and main fuse 2 Measure the mains voltage on the main connector B Not responding to DMX controller 1 DMX LED should be on If not check DMX connectors and cables to see if link properly 2 If the DMX LED is on and no response to the channel check the address settings and DMX polarity 3 If you have intermittent DMX signal problems check the pins on connectors or on PCB of the fixture or the previous one 4 Try to use another DMX controller 5 Check if the DMX cables run near or run alongside to high voltage cables that may cause damage or interference to DMX interface circuit C No response to the sound 1 Make sure the fixture does not receive DMX signal 2 Check microphone to see if it is good by tapping the microphone Visio 10 touched by color LED HC 101 9 Fixture Cleaning The cleaning of internal must be carried out periodically Cleaning frequency depends on the environment in which the fixture operates damp smoky or particularly dirty surrounding can cause greater accumulation of dirt Clean with soft cloth using normal glass cleaning fluid e Always dry the parts carefully Clean the external at least every 20 days Visio 11 touched by color LED HC 101 Visio 12 touched by color
8. t expose the fixture to rain or moisture e There are no user serviceable parts inside the fixture Do not open the housing or attempt any repairs by yourself In the unlikely event your fixture may require service please contact your nearest dealer Visio 7 touched by color LED HC 101 2 Technical Specifications e Acompact LED controller for all kinds of DC 24V passive RGB Fixtures e Come with switch power supply inside e Built in programs under Master Slave mode triggered by music e 4 different ways of DMX addressing Terminals for linking LED Wall Dimmer and it provides power to LED Wall Dimmer Power input 120 240V 50 60Hz Power output DC 24V e Max Load 100W Channels Channel 1 Red Channel 2 Green Channel 3 Blue Channel 4 Dimmer Strobe Dimension 356 x 132 x 43 mm e Weight 2kg 1 DMX INTPUT input DMX signal 2 DMX OUTPUT output DMX signal 3 POWER SOCKET for power input 4 LED show the status of the unit 5 DIP SWITCH used to set the start address of the unit or choose functions 6 AUTO DMX ADDRESS used to set start address automatically Visio d touched by color LED HC 101 7 LED WD CONNECTOR used to receive the signal of LED WD only 8 SIGNAL OUTPUT output signal and power for light 4 Installation 1 Ensure that mains power supply is off before installing or wiring the LED fixture 2 Unscrew the screws and connect the wires as diagrams below 3
Download Pdf Manuals
Related Search