User Manual
Contents
1. The RJ 45 ports are auto sensing for 10Base T or 100Base TX devices connections Auto MDI MDIX means that you can connect to another switch or workstation without changing straight through or crossover cabling See figures as below for straight through and crossover cable schematic m RdJ 45 Pin Assignments Pin Number Assignment 1 TX 2 Tx 3 Rx Note 6 Rx and each wire pair signs represent the polarity of the wires that make up All ports on this industrial switch support automatic MDI MDI X operation you can use straight through cables See Figure below for all network connections to PCs or servers or to other switches or hubs In straight through cable pins 1 2 3 and 6 at one end of the cable are connected straight through to pins 1 2 3 and 6 at the other end of the cable The table below shows the 10BASE T 100BASE TX MDI and MDI X port pin outs Pin MDI X 1 Signal Name Receive Data plus RD MDI Signal Name Transmit Data plus TD Receive Data minus RD Transmit Data minus TD O N Transmit Data plus TD Transmit Data minus TD Receive Data plus RD Receive Data minus RD Switch 3 TD 3 RD 6 TD gt 6 RD TD TD 1 RD _ 2 RD lt 2 Router or PC Straight Through Cable Schematic Switch Switch 3 TD 3 TD 6 TD 6 TD2. Then check for loose power connections power losses or surges at power outlet IF you still cannot resolve the problem contact your local dealer for assistance m If the LED indicators are normal with the correctly connected cables and the packets still cannot transmit please check your system s Ethernet devices configuration or status Technical Specification Communications Compatibility LAN Transmission Distance Transmission Speed Broadcast Storm Rate Limit Interface Connectors LED Indicators Power Power Consumption Power Input The technical specifications of the Industrial Switch are listed as follows IEEE 802 3 802 3u 10 100Base TX Up to 100 m Up to 100 Mbps 200pps 100M 20pps 10M 5 x RJ 45 5 port 10 100TX 8 x RJ 45 8 port 10 100TX 6 pin removable screw terminal power Unit P1 P2 Fault TX port Link Active Full Duplex Collision 5 port 10 100TX 2 93W standard model 2 88W wide operating temp model 8 port 10 100TX 4 71W standard model 3 84W wide operating temp model 2 x Unregulated 12 48 Vpc 17 Fault Output Mechanism Dimensions WxHxD Enclosure Mounting Protection ESD Ethernet Surge EFT for power Power Reverse Environment Operating Temperature Operating Humidity Storage Temperature Certifications Safety EMC 1 Relay Output 30 x 95 x 140 IP 30 Metal shell with solid mounting kits DIN35 rail Wall 6 00
3. heeeiatededst 1 MOJU ION aea nemunaidiaietonaseeteoimette 1 FOAIUNES ince E a ease eeaen 3 PACKING Lioliai 4 Salely FrecautiOn ssrsn nan 4 Hardware Description cccccseeeeeeeseeeeeesaneeeees 5 Front Paheli orasi e a a aa 5 TOP VIG Warana a ts 6 Wiring the Power Inputs cceseeeeeeeeeeeeeeeeeeeeees 6 Wiring the Fault Alarm Contact cere 7 EE GIG ALORS eae AN 8 POMS rank a 8 C ADAG asistsiccicetire center iaeua cies amnania tie 10 Mounting Installation cccccsseseeeeeseeeeeeeeeees 11 Wall Mount Plate Mounting seeeeeeeeeeees 13 Hardware Installation cceeceseeseeeseeeeeseeenes 14 Installation Stems ccisicveloisva canciones ties 14 TOWDIES INO QUO escasas R 16 Technical Specification cccccsssesceceeeeeeeees 17 Overview Introduction This user manual is suitable for the products as follows e 5 port 10 100TX Unmanaged Industrial Switch e 8 port 10 100TX Unmanaged Industrial Switch The unmanaged industrial switch is a cost effective solution and meets the high reliability requirements demanded by industrial applications High Speed Transmissions The Industrial switch includes a switch controller that can automatically sense transmission speeds 10 100 Mbps The RJ 45 interface can also be auto detected so MDI or MDI X is automatically selected and a crossover cable is not required All Ethernet ports have memory buffers that support the store
4. 0 Vpc 3 000 Voc Yes 40 75 C wide operating temp model 10 60 C standard model 5 95 non condensing 40 85 C UL cUL CE EN60950 1 FCC Class A CE EN61000 4 2 ESD CE EN61000 4 3 RS 18 Free Fall Shock Vibration CE EN61000 4 4 EFT CE EN61000 4 5 Surge CE EN61000 4 6 CS CE EN61000 4 8 CE EN61000 4 11 CE EN61000 4 12 CE EN61000 6 2 CE EN61000 6 4 IEC60068 2 32 IEC60068 2 27 IEC60068 2 6
5. 1 RD 1 RD 2 RD 2 RD Cross Over Cable Schematic Cabling Use the four twisted pair Category 5 cabling for RJ 45 port connection The cable between the switch and the link partner switch hub workstation etc must be less than 100 meters 328 ft long Mounting Installation DIN Rail Mounting The DIN Rail is screwed on the industrial switch when out of factory If the DIN Rail is not screwed on the industrial switch please see the following figure to screw the DIN Rail on the switch Follow the steps below to hang the industrial switch Rear Side DIN Rail 1 Use the screws to screw on the DIN Rail on the industrial switch 2 To remove the DIN Rail reverse the step 1 3 First insert the top of DIN Rail into the track 4 Then lightly push the button of DIN Rail into the track 5 Check the DIN Rail is tightly on the track 6 To remove the industrial switch from the track reverse steps above Wall Mount Plate Mounting Follow the steps below to mount the industrial switch with wall mount plate 1 Remove the DIN Rail from the industrial switch loose the screws to remove the DIN Rail Place the wall mount plate on the top amp bottom side of the industrial switch Use the screws to screw the wall mount plate on the industrial switch Use the hook holes at the corners of the wall mount plate to hang the industrial switch on the wall To remove the wall mount plate reverse steps ab
6. 5 port amp 8 port 10 100BaseTX Industrial Switch User Manual Rev 1 06 21 Jan 2008 FCC Warning This Equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy It may cause harmful interference to radio communications if the equipment is not installed and used in accordance with the instructions However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures m Reorient or relocate the receiving antenna m Increase the separation between the equipment and receiver m Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help CE Mark Warning This is a class A product In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures Content PGC Wa IAIN esis cst eeens at iieceoe CE MIK Warning tahes a E NENI EW a aa
7. and forward mechanism This assures that data is properly transmitted Dual Power Input To reduce the risk of power failure the Industrial switch provides 12 48 Vpc dual power inputs If there is power failure Industrial switch will automatically switch to the secondary power input Flexible Mounting The industrial switch is extremely compact and can be mounted on a DIN rail or a panel so it is suitable for any space constrained environment Advanced Protection The power line of Industrial switch supports up to 3 000 Vpc EFT protection which secure equipment against unregulated voltage and make systems safer and more reliable Meanwhile 6 000 Voc ESD protections for Ethernet ports make Industrial switch more suitable for harsh environments Wide Operating Temperature The operating temperature of the Industrial switch is between 40 75 C wide operating temperature model or 10 60 C standard model With such a wide range you can use the Industrial switch in some of the harshest industrial environments that exist Easy Troubleshooting LED indicators make troubleshooting quick and easy Each 10 100 Base TX port has 2 LEDs that display the link status transmission speed and collision status Also the three power indicators P1 P2 and Fault help you diagnose immediately Features Provides 5 x 10 100 Mbps 5 port 10 100TX model or 8 x 10 100 Mbps 8 port 10 100TX model Ethernet ports Supports full nalf duplex f
8. low control Supports MDI MDI X auto crossover Supports surge EFT protection 3 000 Voc for power line Supports 6 000 Vpc Ethernet ESD protection Provides broadcast storm protection Embedded with a switch controller supports auto negotiation Embedded with memory buffer supports store amp forward transmission Supports redundant 12 48 Vpc power input Provides flexible mounting DIN rail Panel Mounting Supports operating temperatures from 40 75 C wide operating temperature model or 10 60 C standard model Packing List 1x 5 port 10 100TX Industrial Ethernet Switch or 1x 8 port 10 100TX Industrial Ethernet Switch m 1x User Manual m 2 x Wall Mounting Bracket and Screws Safety Precaution Attention IF DC voltage is supplied by an external circuit please use a protection device on the power supply input Hardware Description In this paragraph we will introduce the Industrial switch s hardware spec port cabling information and wiring installation Front Panel The Front Panel of the 5 port and 8 port 10 100BaseTX Industrial Switch is shown as below ooo LED Indicator RJ 45 Port CT Front Panel of the 5 port amp 8 port 10 100BaseTX Industrial Switch Top View The top panel of the 5 port amp 8 port 10 100BaseTX Industrial Switch is equipped one terminal block connector of two power inputs Top Panel of the 5 port amp 8 port 10 100BaseTX Industrial Switch Wiring the Po
9. ove Hardware Installation In this paragraph we will describe how to install the 5 port or 8 port 10 100Base TX Industrial Switch and the installation points for the attention Belt E E Data collect server Human Management Interface Enterprise Switch Industrial Industrial Industrial Switch Switch Switch Field Management Programmable logic controller 7 0 Device Server l f Field Automatic device Field Automatic device Field Automatic device Distribute 1 0 control system Installation Steps 1 Unpack the Industrial switch packing 2 Check the DIN Rail is screwed on the Industrial switch If the DIN Rail is not screwed on the Industrial switch Please refer to DIN Rail Mounting section for DIN Rail installation If you want to wall mount the Industrial switch then please refer to Wall Mount Plate Mounting section for wall mount plate installation 3 To hang the Industrial switch on the DIN Rail track or wall please refer to the Mounting Installation section 14 4 Power on the Industrial switch How to wire the power please refer to the Wiring the Power Inputs section The power LED on the Industrial switch will light up Please refer to the LED Indicators section for meaning of LED lights 5 Prepare the twisted pair straight through Category 5 cable for Ethernet connection 6 Insert one side of Category 5 cables into the Industrial switch Ethernet port RJ 45 port and anothe
10. r side of category 5 cables to the network devices Ethernet port RJ 45 port ex switch PC or server The UTP port RJ 45 LED on the Industrial switch will light up when the cable connected with the network device Please refer to the LED Indicators section for LED light meaning Note Be sure the connected network devices support MDI MDI X If it does not support then use the crossover category 5 cable 7 When all connections are all set and LED lights all show in normal the installation is complete Troubleshooting m Verify that you are using the right power cord adapter Please don t use the power adapter output higher than the power input of this switch or it will burn this switch down m Select the proper UTP STP cable to construct your network Please check that you are using the right cable Use unshielded twisted pair UTP or shield twisted pair STP cable for RJ 45 connections 100 2 Category 3 4 or 5 cable for 10Mbps connections or 100Q Category 5 cable for 100Mbps connections Also be sure that the length of any twisted pair connection does not exceed 100 meters 328 feet m Diagnosing LED Indicators To assist in identifying problems the switch can be easily monitored through panel indicators which describe common problems the user may encounter and where the user can find possible solutions m F the power indicator does not light on when the power cord is plugged in you may have a problem with power cord
11. wer Inputs Please follow the steps below to insert the power wire V V V V 1 Insert the positive and negative wires into the V and V contacts on the terminal block connector 2 To tighten the wire clamp screws for preventing the wires to loose 6 Wiring the Fault Alarm Contact The fault alarm contact is in the middle of terminal block connector as the picture shows below Inserting the wires it will detect the fault status which the power is failure or port link failure for managed model and form an open circuit Note The wire gauge for the terminal block should be in the range between 12 24 AWG LED Indicators There are few LEDs display the power status and network status located on the front panel of the Industrial switch each of them has its own specific meaning as below table LED Color Description On Power input 1 is active P1 Green Off Power input 1 is inactive On Power input 2 is active P2 Green Off Power input 2 is inactive On Power input 1 or 2 is inactive Fault Red oe Power input 1 and 2 are both functional or no power inputs On Connected to network Link Active Green Flashing Networking is active 1 5 or 1 8 Off Not connected to network On Ethernet port full duplex Duplex Collision 1 5 or 1 8 Orange Flashing Collision of packets occurs Off Ethernet port half duplex or not connect to network Ports RJ 45 ports Auto MDI MDIX
Download Pdf Manuals
Related Search