HM100P User Manual
Contents
1. When two HM100P headsets are connected you will be able to use the intercom features 1 Send out intercom Press and hold V and V together for about 2 seconds then release it until you hear a short tone NOTE When HM100P is connected with another intercom and a cell phone at the same time you will not be able to send out intercom during a phone call 2 Cancel intercom Briefly press MFB button when sending out intercom You will hear a short tone 3 Answer intercom Briefly press MFB button you will hear a short tone 4 End intercom Briefly press MFB button You will hear a short tone 5 Reject intercom Press and hold the MFB button for about 2 seconds when receiving intercom 6 Volume up Short or long press VOL button You will hear two DU tones when max or min volume is reached 7 Volume down Short or long press VOL button you will hear two DU tones when max or min volume is reached 8 Call Features When HM100P is connected with a Bluetooth cell phone you will be able to make calls with HM100P 1 Answer a call Briefly press MFB button 2 Enda call Briefly press MFB button 3 Reject a call Press and hold the MFB button for 2 seconds 4 Cancel a call Briefly press MFB button when the call is not connected 5 Redialling last number Press MFB button twice quickly 6 Volume up Short or long press VOL button You will hear two DU tones when max volume is reached 7 Volume down Sho2. the other interphone until Blue LED is steady D The interphone whose blue LED is steady will automatically search and connect the interphone which is in pairing mode After successfully connecting the blue LEDs of both interphones will flash twice every 4 Secs 3 Pairing with two Bluetooth devices A Follow the above steps to pair it with one Bluetooth device Once successfully paired the LED will flash blue twice every 4 seconds B Press and hold the MFB button for 3 to 5 seconds until the LED flashes blue and red HM100P has entered pairing mode again C Search the Bluetooth device and get them paired and connected D The HM100P is now paired and connected with two Bluetooth devices NOTE e HM100P will switch to standby mode automatically if it can t pair with any device within 2 minutes e HM100P will power itself off if it is not connected with any device within 10 mins e HM100P can connect with two devices simultaneously either two cell phones or a cell phone and an interphone You can connect HM100P with the other Bluetooth device when it is in standby or intercom Status e Once paired and connected with two Bluetooth devices it will automatically connect to the two devices whenever you turn the HM100P on provided that the HM100P is within range We found most problems are caused by improper pairing between the headset and the Bluetooth device Please follow the online instructions step by step 7 Intercom Features
3. 1 Product Description Avantree HM100P is a Bluetooth helmet headset for any Bluetooth Device Together with the freedom to travel by motorcycle HM100P gives you the comfort of a Bluetooth wireless communication Its water resistant body guarantees total peace of mind even in the rain and an updated A2DP profile supports music and GPS when riding Innovative noise reduction minimizes traffic and wind noise through the microphone and direct helmet to helmet connection makes rider to passenger or rider to rider easier to keep in touch while on the go within 33 feet wireless connection 2 Product Overview 1 Volume down Next 2 LED indicator 3 MFB 4 USB port 5 Volume up Previous 6 Speakers 7 Microphone What s in the box a Bluetooth headset main body b Two speakers and boom microphone c Helmet shaping mat d Velcro pad for shaping mat e Ear Speaker Velcro f Mini USB charging cable g User manual h Warranty card 3 Installing 1 Installing the Velcro to the interphone headset helmet A Find the best location for the headset on the helmet and make sure it is clean and dry B Attach the shaping mat to the location C Remove the protective strip from the double sided adhesive and carefully fix the Velcro to the surface of the plastic pad NOTE You need check the position of the Velcro carefully Once fixed it will not be possible to move it without damaging the Velcro Velcro Shaping ma
4. ent generates uses and can radiate radiofrequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help 11 4 Trademark Statement The Bluetooth word mark and logos are owned by the Bluetooth SIG Inc Avantree is a trademark owned by Avantronics Limited 13 Warranty Please refer to the warranty card included in the pack Technical Support For more information about this product and other Avantree Bluetooth products including video user guides and online technical support please visit the www avantree com Due to the nature of our products there may be software updates made without notice Please always refer to the Avantree website for the latest information Dispose of the packaging and a this product in accordance with w C Fe the lates
5. g the HM100P at least every two months NOTE When the battery becomes low the red LED will flash and the HM100P emits 3 DU tones every 30 seconds Please recharge the battery fully as described above When you can t turn off the Bluetooth interphone you can turn it off as soon as you charge it 5 Turning ON OFF Turn On From OFF press and hold the MFB button for around 3 seconds until the indicator LED shows blue for 1 second and flashes twice You will also hear a long tone Turn Off From ON press and hold the MFB button for around 7 to 8 seconds until the indicator LED shows red for 1 second and flashes twice You will also hear a long tone 6 Pairing connect Tutorial online 1 Pairing with a Bluetooth cell phone A Keep HM100P and Bluetooth cell phone within 1 meter when pairing B Press and hold the MFB button for 3 to 5 seconds until the LED flashes blue and red You will also hear two tones C Search the headset from your phone D Once Avantree HM100 found in search list follow the steps and enter pin code 0000 to pair some phones do not request the pin code E Connect the headset to your phone The LED indicator will flash twice every 4 seconds if connected successfully F HM100P is ready for use now 2 Pairing with an another HM100P for interphone A Keep two interphones within 1 meter when pairing B Make one of the interphones enter pairing mode C Press and hold the MFB button of
6. ht 52g The talk and standby times may vary when used with different mobile phones or other compatible Bluetooth devices usage settings usage styles and environments 11 Declaration of Conformity 11 1 EU This product is CE certified according to the provision of the R amp TTE Directive 99 5 EC We declare that this product is in compliance with the essential requirements and other relevant provisions of Directive 1999 5 EC 11 2 FCC Statement 1 This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions e This device may not cause harmful interference e This device must accept any interference received including interference that may cause undesired operation 2 Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment 11 3 RF Warning Statement The device has been evaluated to meet general RF exposure requirement The device can be used in portable exposure conditions without restriction Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment NOTE This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipm
7. rt or long press V button You will hear two Du tones when min volume is reached Set factory defaulted settings Ensure the headset is standby mode then press and hold V button until RED LED light up NOTE When HM100P is connect with another intercom and a cell phone at the same time you can answer calls and make calls via your mobile phone resume In intercom status when call is completed HM100P will revert to intercom status 9 Music Streaming Please enter into your phone s music player before listening music on the headset music will be automatically heard on your headset for some phones some need to transfer music from phone to the headset 1 Volume Up Briefly press V to increase volume 2 Volume Down Briefly press V to decrease volume 3 Play music Press MFB Button 4 Pause Press MFB Button 5 Previous track Press and hold V Button 6 Next track Press and hold V Button NOTE Some functions are dependent on the mobile phone being used with the headset and may not work with some phones where those features are not supported 10 Product Specification e Bluetooth V2 1 e Support profiles Headset profile and hands free profile e Operation range Class 2 10 meters e Talk time up to 7 hrs e Standby time up to 80 hrs e Charging time About 2 hours e Charging voltage DC 5V 500mA e Main body dimensions 100 20 35mm e Microphone arm 230mm e Weig
8. t Helmet 2 Installing the HM100P main body Take your HM100P main body remove the protective strip make the USB port points down and attach it to the Velcro NE 2 3 Installing the ear speaker and microphone A Take the two speakers Velcro test for the best position to fix them The Velcro should be fixed inside the helmet as close as possible to the ears B Remove the protective strip and apply the Velcro C Take the ear speakers and attach it to the Velcro D Adjust the microphone arm along down to where your mouth will be Stick speaker pads Place speakers ol ne wedi PA lt Speaker 2 R Hide speaker cable J NOTE Put the helmet on a few times to find the optimum position Once fixed the equipment will not be easy to move 4 Connecting the ear speaker and microphone to HM100P main body Connect USB cable to the USB port of HM100P main body carefully Now Avantree HM 100 is installed successfully TF7 Y2 Aa T A O gt 4 Charging 1 For first time use please charge your HM100P until the battery reaches its full capacity This usually takes about 2 hours 2 Afterwards each charge cycle may take up to 2 hours 3 LED will indicate red when charging and off when charging is complete 4 If you have not used the item for a few months LED might not turn red when first charging It might take 15 35 minutes before the LED turns red 5 We suggest fully chargin
9. t provisions FCC ID WJ5 HM100 QD ID BO14717 Z PKMN HM100P 000
Download Pdf Manuals
Related Search