ww-45 digital indicator
Contents
1. 0 9999 dP position of the decimal point ZP lower limit of the measuring range value displayed at 4mA EP upper limit of the measuring range value displayed at 20mA FILt damping min 0 3s max 20 0s HILO exceeding the range off function inactive on function active In case of the activated function the signal dropping below 4mA is signaled by the message LO whereas the increase above 20mA by the information HI In case of an inactive function exceeding the range of indication 1999 9999 is not signalled SIon activating value of the alarm threshold SIoF deactivating value of the alarm threshold HY I function available after selecting the option HYon hysteresis range of insensibility regarding the set values of the alarm threshold The device switches into the alarm mode following the exceeding of the Slon value and leaves the alarm mode after exceeding the SIoF value CP I function available after selecting the option HYoF signaling of the work mode within the range of the set alarm values If Slon gt SIoF the alarm mode is activated when the measured value remains within the range of the set threshold parameters If SIon lt SIoF the alarm mode is activated when the measured value falls beyond the range of the set threshold parameters dlon delay time after which the alarm threshold is activated in the range betwe2. QPLISEN S IO WW 45 01 ENG APLISENS MANUFACTURE OF PRESSURE TRANSMITTERS AND CONTROL INSTRUMENTS USER S MANUAL WW 45 DIGITAL INDICATOR WARSAW JANUARY 2006 APLISENS Sp z 0 0 03 192 Warszawa ul Morelowa 7 tel 0 22 814 07 77fax 0 22 814 07 78 www aplisens pl e mail aplisens aplisens p AE 1 IO WW 45 01 ENG CONTENTS GENERAL CHARACTERISTICS aaxntntvtvtvtvssssesssnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnunm 2 TECHNICAL DATA 222020200200000000000000000000000000000000000000000000000000000000000000000000000000000000 2 WAY OF CONNECTING 1 2122202200 2000000000000000000000000000000000000000000 0000000000 0000000000 000008 2 CONFIGURATION OF THE DEVICE aa ndntvseseses ssnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnn0 0 2 4 1 NOSE ORIEN S EEEE aid AR doza AR od 2 4 2 CONFIGURATION PARAMETERS aiaiiaiaiaaanaaaaiaa nantananannnnanannanananannnnnnnananandnnanandanan 3 1 2 3 4 2 IO WW 45 01 ENG GENERAL CHARACTERISTICS The display WW 45 designed to co operate with any device with the output signal of 4 20mA and equipped on its output with a standard DIN 43650 connector joint The typical application of the display is the addition of a local indicator to the remote pressure or pressure difference measurement The WW 45 has a configurable range of indication between 1999 and 9999 it is equipped with a LED display red with the digits 7 62mm high It does not requ
3. en 0 100s dlof delay time after which the alarm threshold is de activated in the range between 0 100s HIPr value of the highest registered pressure Deleting the values by the simultaneous pressing of the A and B keys LoPr value of the lowest registered pressure Deleting the values by the simultaneous pressing of the A and B keys CONFIGURATION SETTING press A or B in order to select the proper configuration parameter press A and B simultaneously in order to enter the parameter programming level press A or B to set the desired value for the parameter press A and B simultaneously to accept the set value for the parameter
4. ire external power supply It is equipped with a configurable two mode output of the open collector type as a standard TECHNICAL DATA Display error 0 2 1 digit Input signal 4 20mA generated by voltage max 36V Voltage drop max 6V Ambient temperature 0 70 C Degree of protection of the housing IP 65 Max current of the two mode output 90mA WAY OF CONNECTING The display is installed between the plug and the socket of the connector joint The whole device is tightened with a clamping screw Fig 1 Scheme of the electric leads Input signal between 1 and 2 4 20mA max 40mA Two mode output between minus of power and 3 Ro internal resistance of the two mode output CONFIGURATION OF THE DEVICE 4 1 USE OF KEYS left key A moving up in the menu as well as increasing the parameter value during the programming right key B moving down in the menu as well as decreasing the parameter value during the programming the keys A and B used simultaneously entering the parameter programming level as well as confirmation of the displayed parameter 3 IO WW 45 01 ENG 4 2 CONFIGURATION PARAMETERS o R PAxx PAon access code factory setting 5 PAoF password inactive free access to the menu The password is activated again after number 5 has been selected again Changing the password after entering the code 0835 and typing a new code from the range between
Download Pdf Manuals
Related Search