Noble Beam200 (5R) User Manual
Contents
1. D The appliance does not appear to operate normally or exhibits s marked change in performance WARNING Avoid Electric Shock High temperature of bulb EPL FIRE WARNING A MINIMUM DISTANCE TO FLAMMABLE MATERIAL 12M W 3 42 DMX Linking To ensure proper DMX data transmission when using several DMX units try to use the shortest cable path possible The order in which units are connected in a DMX line does not influence the DMX addressing For example a unit assigned a DMX address of 1 may be placed anywhere in a DMX line at the beginning at the end or anywhere in the middle When a unit is assigned a DMX address of 1 the DMX controller knows to send DATA assigned to address 1 to that unit no matter where it is located in the DMX chain POWER SUPPLY MAINS Use the plug provide to connect the mains power to the projector paying attention to the voltage and frequency marked on the panel of the projector It is recommended that each projector be supplied separately so that they may be individually switched on and off IMPORTANT fo i O It is essential that each projector is correctly earthed and that electrical N a S installation conforms to all relevant standards Power consumption of this projector is 400W Mounting bracket Every unit can be placed on the ground or hanging installation in any position The fast lock system makes it quick and simple to install bracket to four locations see Figure2. to remove or break off the ground prong from the electrical cord This prong is used to reduce the risk of electrical shock and fire in case of an internal short e Disconnect from main power before making any type of connection e Do not remove the cover under any conditions There are user serviceable parts inside e Never operate this unit when its rear cover is removed e Never plug this unit into a dimmer pack e Always be sure to mount this unit in an area that will allow proper ventilation Allow about 6 15cm between this device and a wall e Do not attempt to operate this unit if it becomes damaged e During long periods of non use disconnect the units main power e Always mount this unit in safe and stable matter e Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them paying particular attention to the point they exit from the unit e Cleaning unit should be cleaned only as recommended by the manufacturer See Cleaning for details e Heat The appliance should be situated away from heat sources such as radiators heat registers stoves or other appliances including amplifiers that produce heat e The unit should be serviced by qualified service personnel when A The power supply cord or the plug has been damaged B Objects have fallen or liquid has been spilled into the appliance C The appliance has been exposed to rain or water
3. unit If problems are not resolved contact with your dealer for service 4 Specifications Model Name Noble Beam200 5R Power 220V 50 60Hz 110V version is available upon request Power consumption 400W Working postion Any safe working position Lamp Philips MSD200R5 Optional Yodn and Jenbo MSD Platinum 5R 200W 160W 7800K 300K 2000 hr Eco mode Motors 13 step motors Cooing Forced ventilation with axial fans Inputs DMX512 Channels 17 Pan Tilt 540 270 Resolution Pan 2 11 Pan Fine 0 008 Tilt 0 98 Tilt Fine 0 004 Wateproof IP rating IP20 Weight 17Kg
4. 42 Color 4 Color 5 43 46 Color 5 47 51 Color 5 Color 6 52 55 Color 6 56 59 Color 6 Color 7 60 63 Color 7 64 68 Color 7 Color 8 69 72 Color 8 73 76 Color 8 Color 9 77 81 Color 9 82 85 Color 9 Color 10 86 89 Color 10 90 93 Color 10 Color 11 94 98 Color 11 99 102 Color 11 Color 12 103 106 Color 12 107 110 Color 12 Color 13 111 115 Color 13 116 119 Color 13 Color 14 120 123 Color 14 124 127 Color 14 White 128 255 Color wheel rotation Flash 0 3 Close 4 103 Strobe 104 107 Open 108 207 Fast 208 212 Open 213 225 Slow 226 238 Medium 239 251 Fast 0 255 Dark 3 bright 4 0 3 Open 4 7 Gobo1 8 11 Gobo2 12 15 Gobo3 16 19 Gobo4 20 23 Gobo5 24 27 Gobo6 28 31 Gobo7 32 35 Gobo8 36 39 Gobo9 40 43 Gobo10 44 47 Gobo11 48 51 Gobo12 52 55 Gobo13 56 59 Gobo14 60 63 Gobo15 64 67 Gobo16 68 71 Gobo17 72 113 Gobo rotation forward 114 117 Stop 118 159 Gobo rotation backward 160 166 Gobo1 Shake slow to quick 167 172 Gobo2 Shake slow to quick 173 179 Gobo3 Shake slow to quick 180 185 Gobo4 Shake slow to quick 186 191 Gobo5 Shake slow to quick 192 198 Gobo6 Shake slow to quick 199 204 Gobo7 Shake slow to quick 205 211 Gobo8 Shake slow to quick 212 217 Gobo9 Shake slow to quick 218 223 Gobo10 Shake slow to quick 224 230 Gobo11 Shake slow to quick 231 236 Gobo12 Shake slow to quick 237 243 Gobo13 Shake slow to quick 244 249 Gobo14 Shake slow to quick 250 255 Gobo15 Shake slow to
5. Instruction Manual PROFESSIONAL SHOW LIGHT BEAM200 5R Unpacking Thank you for purchasing this unit Every unit has been thoroughly tested and shipped in perfect condition Carefully check the shipping carton for damage that may have occurred during shipping If the carton appears to be damaged carefully inspect your unit for any damage and be sure all accessories necessary to operate the unit has arrived intactly In the case damage has been found or parts are missing please contact the manufacturer or your dealer for further instructions Do not return this unit to your dealer without any warning Caution There are no user serviceable parts inside this unit Do not attempt any repairs yourself doing so will void your manufacturer warranty In the unlikely event your unit may require service please contact the manufacturer or your dealer PLEASE recycle the shipping carton whenever possible General Instructions To optimize the performance of this product please read these operating instructions carefully to familiarize you with the basic operations of this unit These instructions contain important safety information regarding the use and maintenance of this unit Please keep this manual with the unit for future reference Safety Precautions e Be sure that the local power outlet match that of the required voltage for your unit e Do not attempt to operate this unit if the power cord has been frayed or broken Do not attempt
6. Operating Modes You can use the LED unit in 4 ways e Sound Active mode The unit will react to sound chasing through the built in programs e Auto Mode The unit will automatically chase through the different colors e DMX control mode This function will allow you to control each individual units traits with a standard DMX 512 controller e Master slave mode One unit will work as the master in the one of the above three modes other units in the chain will work in synchronization towards the master LCD display and button LCD DISPLAY There is one simple button beside the LCD screen controls whole operation MENU DOWN ENTER UP Press button to activate main menu enter next menu or back Turn button left to browse last options or decrease DMX value turn right to browse next options or increase DMX value When the fixture is powered resetting or connected to DMX console the LCD display will show Beam 200 Sharpy Address 1 Now the fixture is ready for work 1 Menu operation The main menu options of Beam 200 include Exit DMX Address Parameter Option Display Main control Test operation Resume default Fixture reset 1 1 Exit Press button after power fixture Exit is the first option in list 1 2 DMX Address In the main menu select DMX Address the LCD will show DMX Address Address 1 Then you can set dmx address from 1 to 512 1 3 Parameter Select Parameter there are th
7. quick Prism 0 127 No prism 128 255 Prism Prism rotation 0 21 42 63 84 105 450 127 540 128 190 Prism rotation forward 191 192 Stop 193 255 Prism rotation backward 0 255 NE E 8 Frost 0 255 Doo O 0 255 Doo O 10 Pan 0 255 PT 11 0 255 12 0 255 PT 13 Tilt fine 0 255 PT 147 No Function PO 15 ij ROGER J o ee 16 Lamp control 0 59 No function 60 63 Lamp Off 64 255 Lamp On Pan Tilt speed 0 255 Fast Slow Chart size Cleaning Due to fog residue smoke and dust cleaning the internal and external optical lenses must be carried out periodically to optimize light output 1 Use normal glass cleaner and a soft cloth to wipe off the outside casing 2 Clean the external optics with glass cleaner and a soft cloth every 20 days 3 Always be sure to dry all parts completely before plugging the unit back in Cleaning frequency depends on the environment in which the unit operates i e smoke fog residue dust dew Trouble Shooting Listed below are a few common problems the user may encounter with solutions Unit not responding to DMX Check that the DMX cables are connected properly and are wired correctly pin 3 is hot on Some other DMX devices pin 5 may be hot Also check that all cables are connected to the right connectors It does matter which way the inputs and outputs are connected Not responding to sound Quiet or high pitched sounds will not activate the
8. ree sub options Back Control Models enter Control you can select three modes as below Back Standa Control xtanded ma Models B200W Light 1 4 Option Enter Option there are 8 options to use Back X Reverse Y Reverse XY Optocoupler Lamp control Lamp ON OFF Turn shortest Color half All of them can be activated by NO YES Lamp ON OFF means to select the lamp of fixture to be on once power on or lamp on when control by console only Back X Reverse Y Reverse XY Optocoupler Lamp control Lamp ON OFF Turn shortest Color Half 1 5 Display This is a option to select language use English or OO00 1 6 Main control Control all channels by this option there are total 32 channels to use select the channels are available to use only program effect of fixture you want from channel by value 0 255 1 7 Test operation In main menu select Test operation there are three options Back Sound Auto The fixture can be activated by music sound also can run by build in program automatic 1 8 Resume default Make the fixture to be with default set by factory again 1 9 Fixture reset Fixture reset means to reset everything of the fixture DMX Chart No Channel DMX value Color White gt White Color 1 9 12 Color 1 13 17 Color 1 Color 2 18 21 Color 2 22 25 Color 2 Color 3 26 29 Color 3 30 34 Color 3 Color 4 35 38 Color 4 39
Download Pdf Manuals
Related Search