homologation directive mp03 mechanical securtity
Contents
1. An attempted attack is stopped if the lock product can actually be removed and the vehicle can be moved or with regard to vessels the outboard motor or the screw can be removed or the lock product loses its other anti theft characteristics 6 4 4 2 Class Heavy A point product is applied during attack tests e Resistance time lt 4 minutes 0 points e Resistance time between 4 and 5 minutes 1 point e Resistance time gt 5 minutes 2 points Point product Number of tests 6 Maximal number of points to be achieved 12 Minimal number of points required for a positive result 10 A result of one test with 0 points leads in all cases to rejection The above point product is indeed applied during attack tests that are executed during recertification but only to obtain a history of a product So it is not a rejection criterion for recertification see also par 3 7 2 An attack attempt is stopped if the lock product can actually be removed and the vehicle can be moved or in case of vessels the outboard motor or the screw can be removed or if the lock product loses its other anti theft characteristics SCM Homologation Directive MP03 2003 Version 1 22 Appendix 1 Approval Agreement Undersigned parties do declare this agreement with the intention to guarantee the quality of security systems supplied under the approval label in conformity with the requirements as laid down in the Homolog2. 50 x for separate locks 5 x for the entire product Fall height 1 meter In conditioned testing room 3 hr 15 min 1 a 15 min shower b 1 hr dripping G 2 hrs freezing at 20 C The lock shall be opened with the key within 60 seconds after finishing the test SCM Homologation Directive MP03 2003 Version 1 20 6 4 Attack test 6 4 1 General Products must have a resistance time of at least 180 sec standard or 300 sec heavy A product meets approval conditions if it achieves the minimally required number of points for the applicable class 6 4 2 Tools At the testing institute one can request the most recent list containing the brand and type names of the tools per class to be used The composition of the list will be subject to changes Electrical tools 220V high voltage current are not permitted rechargeable tools are If in practice it is demonstrated that different attack methods tools are being used the testing institute may choose these in consultation with the SCM With respect to the use of the different tools the following applies Class standard Tools must be easy to handle and easy to take along without this attracting attention Class heavy A wider choice of tools is possible here 6 4 3 Execution of the test The product is tested under normal conditions in an assembled condition and as per an assembly consistent with part of a vehicle Here the product is
3. Approved lock lock regarding which it has been established after its approval that it meets the requirements of the homologation directive Approval number if a product has positively gone through the type approval and the approval holder meets the stipulations of the SCM the SCM gives that product an approval number Homologation directive grouping of all requirements and stipulations formulated by the SCM for the approval of locks for vehicles and vessels Certified lock approved lock that is certified by the SCM Label number a number beginning with MP3 that is stuck to an approved product and has a direct relationship with the approval number List if after going through the tests a lock product is certified it is placed on the list of certified products and remains on the list as long as it continues to fulfil the requirements Recertification a mandatory re certification depending upon distribution in the Netherlands with a minimum and maximum number of recertifications per year where in each case part of the type approval is repeated in order to continue to guarantee the quality that is represented by the presence of the label of approval Type specification an identity label that the manufacturer assigns to a lock Type approval the certification during which a product is first tested and approved 3 2 Classification of mechanical security systems The requirements that can be set with respect to the various types of products c
4. SCM may refuse its permission in writing The use of the SCM trademark other than as a label of approval is not permitted unless this is specifical ly agreed upon between the approval holder supplier and the SCM 4 4 Approval label 4 4 1 General With the signing of the Approval Agreement the approval holder accepts the obligation to provide all products manufactured in a series of the SCM approved model meant for the Dutch market with a properly attached approval label supplied by the SCM bearing in mind that stated in this context in the conditions or else to see to it that such a label is affixed The following data shall be stated on the above mentioned approval label a text established by the SCM label serial number 4 4 2 Issue of approval labels The first series of approval labels can be issued as soon as the signed approval agreement is received by the SCM Orders must comprise at least 500 or a multiple thereof If however the approval holder sells more than 1 000 copies in a month more approval labels can be issued up to a maximum of 5 000 units 4 4 3 Ordering labels The labels can be ordered from the SCM Delivery time shall be at most 1 week 4 4 4 Prices of labels The price of the label is stated on the price sheet appendix 6 and can be revised annually 4 4 5 Label model SCM Homologation Directive MP03 2003 Version 1 13 The label is an auto adhesive orange sticker with black imprint that can be stu
5. issued by the SCM these will be assessed separately by a Technical Commission of the SCM possibly in consultation with the supplier and or the testing institute Adaptations and interpretations will be published within 30 days after their approval by the Board of Experts of the SCM in numbered Annexes 4 1 4 Publication List The SCM sees to the publication of a list of the products that fulfil the standards listed in this Homologa tion Directive once the SCM has received the signed approval contract The SCM does this by including approved product in an overview of SCM approved products hereinafter referred to as The List The list is published on Internet via www scm nl New products are placed on this list within 5 workdays after the SCM receives the report from the testing institute On request the list is also available by post 4 2 Type approval 4 2 1 Application for type approval For the type approval one can apply directly to the testing institutes on the list published by the SCM 4 2 2 The applicant SCM Homologation Directive MP03 2003 Version 1 No more than one 1 applicant may be registered per brand of security product As soon as a type approval for a security product has been assigned see 4 2 5 one no longer speaks of the applicant but rather the approval holder If the applicant is not the manufacturer of the product both the applicant and the manufacturer in the form of authorisation must sign the appl
6. market in collaboration with all others concerned the SCM has developed a number of activities e Certification of security companies and security products e Supervision of professional expertise requirements examinations and diplomas e Information and educational activities seminars symposia e Research and advice In the realm of mechanical security systems for vehicles and parts of vessels the SCM works on behalf of security systems against theft and burglary by e Formulating requirements for mechanical security systems for vehicles and vessels e Testing mechanical security systems or having them tested by qualified testing institutes e Certifying approved products e Furthering the use of approved products The adoption of existing labels of approval and homologation directives In close consultation with the National Centre for Prevention it has been decided that commencing on 1 August 2002 the SCM would adopt all existing labels of approval VIP TNO in the above men tioned realm with the exception of the two wheeler security ART label of approval of the NCP In this context the SCM will publish new directives that will replace the existing ones SCM Homologation Directive MP03 2003 Version 1 L INTRODUCTION The goal of these homologation directives is to establish minimum requirements with respect to the anti theft function of electro mechanically functioning locks and lock products for vehicles and parts of vesse
7. placed as per the manual or in the manner that is most logical for the user Before attack tests are executed the product and the construction placement and the technical specifi cations will be studied and a choice made on that basis of the tools to be used The tools that are chosen may be used ground and applied according to the judgement of the testing institute The test must be executed six times Brute tests 4 Intelligent tests 2 Total number of tests 6 If the exact specified proportion of brute and intelligent attack tests cannot be executed then in any case the specified total number of tests must be executed SCM Homologation Directive MP03 2003 Version 1 21 6 4 4 Results of attack tests 6 4 4 1 Class Standard A point product is applied during attack tests at type approval e Resistance time lt 2 minutes 0 points e Resistance time between 2 and 3 minutes 1 point e Resistance time gt 3 minutes 2 points Point product Number of tests 6 Maximal number of points to be achieved 12 Minimal number of points required for a positive result 10 A result of one test with 0 points leads in all cases to rejection The above mentioned point product is indeed applied during attack tests that are executed during recertification but only in order to establish a history of a product So it is not a rejection criterion for recertification see also par 3 7 2
8. unless they are revoked in the interim or if the Homologation Directive are revoked after which the approval still remains in effect for at most 1 year Recertifications are executed on the basis of the approval require ments according to which the type approval is issued SCM Homologation Directive MP03 2003 Version 1 2 3 Legal requirements If requirements as per Dutch or European legislation exist with respect to the product or product part then the product or part must also meet these requirements or be certified according to these requirements If the security product makes use of radio waves for example for switching on or off the security product or for detection it must meet all relevant European standards Product parts that exert an influence upon parts of a vehicle specified by legislation to be significant in terms of safety require the approval of the Ministry of Transport Industries The security product must be designed and installed such that every vehicle and vessel that is equipped with it continues to meet technical requirements type approval 2 4 Road safety requirements The security product must in no manner whatsoever in an activated or non activated condition be able to represent a threat to traffic safety The product may not permanently encroach upon or be connected with any part of the brake system of a vehicle unless specific written permission has been granted by the manufacturer of the vehicle Wi
9. HOMOLOGATION DIRECTIVE MP03 MECHANICAL SECURTITY SYSTEMS FOR VEHICLES AND PART OF VESSELS SCM JANUARY 2003 All rights reserved This document or any part of it may not be reproduced by any means or in any form nor registered in any database without the written permission of the SCM For the use of any part of this document you can contact the SCM SCM Stichting Certificering Motorrijtuigbeveiliging Postbus 393 2900 AJ CAPELLE A D IJSSEL Netherlands IS I gt wr PREFACE INTRODUCTION SCOPE 2 1 General 2 2 Entrance date and term of validity 2 3 Legal requirements 2 4 Road safety requirements 2 5 Documents DEFINITIONS OF TERMS 3 1 Definitions 3 2 Classification of mechanical security systems ADMINSTRATIVE REQUIREMENTS 4 1 General 4 2 Type approval 4 3 Use of the SCM name 44 Approval label 4 5 Modification in approved products 4 6 Recertification of approved products 47 Revocation of type approval APPROVAL REQUIREMENTS 5 1 Technical requirements for mechanical locks 5 2 Technical requirements for electric electronical locks SCM Homologation Directive MP03 2003 Version 1 10 10 13 13 14 15 16 17 17 I gt Appendix 1 Appendix 2 Appendix 3 Appendix 4 Appendix 5 Appendix 6 DESCRIPTION OF TESTS 6 1 General 6 2 Test matrix 6 3 Execution of specific tests 6 4 Attack test Approval Agreement Specific stipulations and requirem
10. Key bit part of the key that contains its coding Key mechanism part of the lock that the key recognises Key number ineradicable number and or letter on a key or label or electronic coding on an associated key card that is related to the coding of the key Key profile projection of the vertical cross section profile of a key Key variety practical the actually applied number of coding possibilities Key variety theoretical the mathematically determined maximum number of coding possibilities per profile Key product a structure often consisting of a housing and a pad lock either built in or fastened to the housing which prevents the vehicles or parts of vessels thus secured from being removed by an unauthor ised person Key housing part of the lock that contains the key mechanism and the blocking mechanism Closing socket part of the blocking system in which the closing pin is contained Closing pin part of the blocking system that is directly moved by the cylinder core Resistance time time during which the lock resists the attack test SCM Homologation Directive MP03 2003 Version 1 8 3 1 3 Definitions of the different types of mechanical security systems For definitions of the various types of mechanical security systems the reader is referred to Appen dices 2 3 4 and 5 3 1 4 Administrative definitions Applicant manufacturer or representing agent authorised in writing by the manufacturer to apply for approval
11. S 5 1 Technical requirements for mechanical locks Each lock must have its own unique lock number or production code Keys must bear permanently visible identification for example a brand name The key number must either be on the key or on an attached metal or plastic label If the key number is on an attached metal or plastic label the approval holder must see to it that when a key is handed over the associated key number can be determined c q controlled A lock number and a key number must not have any identifiable relationship Locks may be delivered with at most three 3 identical keys Original spare keys must be able to be obtained locally in the Netherlands by specifying the key number If the manufacturer or his representative supplies new or extra keys this may only take place against presentation of proof of ownership for example the key card or a guarantee certificate Data concerning keys handed out must be stored for at least 3 years by the manufacturer or his representative Extra original keys ordered later bear the indelible specification C copy or D duplicate The key mechanism must have a practical key variance of at least 5 000 per profile The design of the key mechanism must focus on ruling out use in another way than with the correct key No master keys may be supplied 5 2 Technical requirements for electrical electronic components of locks Products that contain electrical or electronic
12. an vary depending upon their application For this reason we have divided the product requirements into two categories as follows Class Standard Effective products focused on the impulse thief with a resistance time of at least 3 minutes using hand tools that are easy to carry along and that can be hid den on the body Class Heavy Effective products focused on the professional thief with a resistance time of at least 5 minutes using heavier tools SCM Homologation Directive MP03 2003 Version 1 4 ADMINSTRATIVE REQUIREMENTS 4 1 General 4 1 1 Execution The approvals are executed as per the Homologation Directive with appendices by a testing house institute chosen by the supplier Before starting testing at the party requesting the test s request he will be given a list of the tools to be used for the various categories 4 1 2 Choice of testing institute The SCM has a list of institutes with which the SCM has established a contract in order for these institutes to be used as testing institutes Concerning the choice of testing institutes and the procedures for approval and recertification reference is made to the standard contract between the testing institute and the SCM can be obtained from the SCM secretariat 4 1 3 Application of the homologation directive If products or parts of products or their functioning does not fall directly within the scope of this directive or if a similarity exists to other directives
13. anism that can be locked and that when locked prevents the outboard motor from being taken away by an unauthorised person Clamping screw clamping bolt a structure with which an outboard motor is fastened to a ship Clamping screw replacing lock a lockable structure to replace one of the bolts with which the motor is fastened to the ship Tube lock a structure that can be slid over the toggles of clamping screws and can then be locked Nut lock a lockable structure that prevents the fastening nut from being removed using normal tools SCM Homologation Directive MP03 2003 Version 1 26 Appendix 5 Specific stipulations and requirements for mechanical security systems of automobiles and delivery vehicles B5 1 General An anti theft locking system for automobiles and delivery vans ensures that such vehicles can only be taken away with force and using special tools under their own power B5 2 Lock type definitions Pedal locks With these products at least 2 pedals including the gas pedal can be clamped such that driving the car is made virtually impossible Gearbox locks With such a product the shifting mechanism of the gearbox is blocked making it impossible to operate the gear lever E For automatics in the P position For manual vehicles in the neutral or reverse position It is preferable to choose the reverse position for this because in the neutral position the vehicle can be pushed or towed away Steering
14. ation Directive MP03 version 1 To maintain this the certification institute SCM and the approval holder supplier lay down the following arrangements Both parties shall adhere to what is stated in this Directive MPO3 version 1 in specific the Administra tive requirements as stated in chapters 4 On behalf of maintenance inspection and publications per approval number a fee is mandatory The amount is mentioned in Appendix 6 In case of non fulfilment of one or more of the obligations mentioned in chapter 4 the following sanctions are possible Withdrawal of the type approval Mandatory recall of the disputed products from the market Removal from the List of SCM approved products To this agreement Dutch Law is applicable Legal disputes that can not be settled in agreement will be put to the relevant court in Rotterdam So stated and signed in triplicate On behalf of SCM On behalf the approval holder On behalf of the supplier Date weirs eect Se ere shod SideReel y Pce Tat chester O a 9 gecaceabuieianeceo ction A oo Namie aaan idee AE AN aaa AAN sa aE aes UNCHON sabenan tenia eaea ardre ta aa re E SACAT Sismature Skew ets EET EEEE EEEE EEE SCM Homologation Directive MP03 2003 Version 1 23 Appendix 2 Specific stipulations and requirements for mechanical security systems for HGV s and contain ers B 2 1 General B 2 2 An anti theft locking system of a HGV or container ensures that o
15. be easily replaced are permitted to become damaged It is permitted that the normal functioning of the product opening closing is no longer possible as a consequence of damage during the attack test SCM Homologation Directive MP03 2003 Version 1 18 T2 T3 T4 T5 T6 T7 T8 T9 T10 T11 T12 SCM Homologation Directive MP03 2003 Version 1 Testmatrix Corrosion test Dust test Heat test Heat test with condensation test Freeze test Drop test Endurance test Cut test Torsion test Tensile test product Attack test Tensile test anchorage elements As per EN 1670 Grade 3 As per ECE Reg 16 par 7 6 3 As per EU 95 56 par 5 2 2 2 As per EU 95 56 par 5 1 3 Seep 6 3 See 6 3 See 6 3 As per EN 12320 force 80 kN Torque bj 1 kNm ns 2kNm t 30 kN ae 60 kN See 6 4 zi 30 kN FA 60 kN 19 6 3 Execution of specific tests 6 3 1 Endurance test The manufacturer must certify that a product presented for approval must be able to undergo a complete open and close cycle 5 000 times and then continue functioning properly with the mainte nance instructions being followed Test method visual inspection of the statement 6 3 2 Drop test Test method per cycle Time per cycle Number of cycles Test conditions 6 3 3 Freeze test Test method per cycle Time per cycle Number of cycles Test conditions Free fall onto concrete surface 15 sec
16. bjects can only be taken using force and special tools or can only be opened on the back or side These mechanical security systems to prevent theft of and from HGV s can in principle be clas sified in 3 categories e Security systems to prevent unwanted linking to or disconnecting parts of a combination e Security systems to prevent unwanted opening of a container boot of an HGV or the cabin e Security systems to prevent unwanted moving of the vehicle Lock type definitions e Container lock a mechanism that can be locked and that must prevent in a locked condi tion the doors of a container or of the boot of an HGV being opened against the owner s wishes or the container in its entirety being taken away e Kingpin lock a mechanism that fits around the cylinder the kingpin of a trailer that can be locked and when locked prevents the trailer from being taken away by an unau thorised person e Clutch lock also known as shaft lock a mechanism that goes around the clutch of the shaft or is built into the clutch that can be locked and that when locked prevents the trailer or other attachment from being taken away by an unauthorised person e Pedal lock this is used to clamp at least 2 pedals including the gas pedal in such a way that it is virtually impossible to drive the vehicle e Steering wheel clamp With this product it is not possible to turn the steering wheel more than one half turn It also prevents the steering whe
17. ck onto a hard surface Dimensions Width 40 mm Length min 40 mm depending on the amount of data 4 4 6 Sample of label GOEDGEKEURD P3 0000000 4 5 Modification in approved products Every technical modification that may have an influence upon the approval must be made known in writing before it is introduced to the SCM and the testing institute where the type approval was carried out This also applies to changes in the user s manual and the assembly instructions The change must be reported by sending A brief description of the relevant change and or depending upon the testing institute followed by sending the modified product or part Drawings of the modified parts t Original drawings of the part on which the relevant modification is clearly shown If new parts are used drawings of the new part as well as a composite drawing on which it is clearly shown which parts may have been taken away or added All modifications must be numbered and dated on the drawings Once the modification has been assessed on the basis of the information sent in the testing institute will inform the approval holder whether the relevant modification without further testing can be introduced with an administrative approval only report to approval holder and the SCM in production or else whether an entirely new or partial approval at the expense of the approval holder is necessary 4 6 Recertification of approved produ
18. components must be subjected to such standards as the requirements specified in Homologation Directive AAO3 for electronic security products for private vehicles specifically with respect to the methods of switching them on and off SCM Homologation Directive MP03 2003 Version 1 17 I gt 6 1 4 6 1 7 DESCRIPTION OF THE TESTS General The testing institute determines the sequence of the tests to be carried out Product parts are tested in the form in which they are assembled and supplied For this the testing institute will choose the most logic and handy installation in spite of directions given by the supplier in the user manual The positioning of product parts during the tests to be carried out is determined by the certifying institute and if possible according to the instructions for use In response to special wishes from a manufacturer it must be demonstrated that during assembly the position in which the tests took place is maintained Product parts are tested in accordance with the summary in chapter 6 2 Not all tests can or need to be carried out The testing institute makes these decisions After the conclusion of each test the product parts must function according to the specifications of the manufacturer and they must not have undergone any deformation and or changes that might have a negative effect upon the functioning of the product parts at that time or in the course of time Parts and accessories that can
19. cts SCM Homologation Directive MP03 2003 Version 1 4 6 1 Recertification general As per these guidelines the certified product is assessed during the production phase after approval by means of so called recertification Recertification consists of two parts specifically periodic production control and random sampling control This recertification must be executed by the testing institute that executed the type certification The SCM informs the approval holder and the testing institute on the basis of the number of labels that have been used when recertification is required The testing institution informs the SCM about the results of recertifications 4 6 2 Production control For production control the approval holder is asked to deliver one 1 security product for every 1000 that have been supplied with an SCM label of approval of the same type approval number with a maximum of one 1 product per calendar quarter and a minimum of one 1 product per calendar year to the testing institute For a first batch of a new approval number production control will involve the first 250 products delivered During this production control it shall be determined whether the product still fulfils requirements and or whether the product still corresponds with the security product delivered for the type approval The SCM retains the right to purchase the relevant product in the market In consultation with the SCM and the testing institute deviatin
20. el from being removed e Triangle eye lock a mechanism that fits into the towing eye of a trailer that can be locked and that when locked prevents the trailer from being taken away by an unauthor ised person e Gear lever lock This product blocks the shifting mechanism of the gearbox making it impossible to operate the gear lever E For automatic vehicles in the P position E For manual vehicles in the neutral or reverse position It is preferable to use the reverse position for this since in the neutral position the vehicle can be towed or pushed away e Wheel clamp a mechanism that can be locked around the entire wheel or around the rim and tyre so that the enclosed wheel can no longer move freely thus preventing the vehi cle from being taken away by an unauthorised person e Combinations of the above equipment This includes products that have an effect upon several parts of the vehicle For example the steering wheel pedal The same require ments apply to these as to the separate products SCM Homologation Directive MP03 2003 Version 1 24 Appendix 3 Specific stipulations and requirements for mechanical security systems for trailers caravans and boat horse trailers B 3 1General The theft proofing locking of a trailer caravan or other attachment ensures that these objects can only be taken away using force and making use of special tools Mechanical security systems to prevent the theft of trailers caravans and o
21. ents for mechanical security systems for HGV s and containers Specific stipulations and requirements for mechanical security systems for trailers caravans and boat horse trailers Specific stipulations and requirements for mechanical security systems for outboard motors for pleasure craft Specific stipulations and requirements for mechanical security systems of automobiles and delivery vehicles Tariffs SCM Homologation Directive MP03 2003 Version 1 18 19 20 21 23 24 25 26 27 28 PREFACE The Institute for the Certification of Vehicle Security Systems SCM is an independent foundation that is the national knowledge and certification institute for theft and burglary prevention with respect to mobile objects Its activities focus on quality in security and the organisation of processes for upgrading prevention The foundation has been issuing guidelines on a regular basis since 1993 in which the requirements are formulated that theft and burglary prevention systems must meet Interested parties are represented in the Board of Experts the security industry the insurance indus try the business community and government bodies In short all parties that have to do with security Agreements are made in close cooperation on behalf of bringing security systems with respect to mobile objects in the Netherlands to a higher level Activities On behalf of realising the desired quality and recognisability in the
22. for customers and private parties must be realised during office hours by means of personal contact with an employee Direct accessibility is obligatory Other responsibilities The supplier shall demonstrate to the SCM that he has entered into an industrial liability insur ance contract with a coverage of at least 2 5 million per claim The industrial activity must fall within the company objectives specified in the excerpt maintained at the Chamber of Commerce This excerpt will be made available for assessment to the SCM 4 2 8 Unfulfilled responsibilities SCM Homologation Directive MP03 2003 Version 1 12 If one or more of the above mentioned responsibilities are not fulfilled the following sanctions are possible Withdrawal of approval Obligatory withdrawal of the disputed products from the market Removal from the list of SCM approved products 4 3 Use of the SCM name The approval holder and the supplier are permitted to use the specification SCM approved for ap proved products If this approval is withdrawn or if the stipulations of the Homologation Directive are not met the approval holder and the supplier are no longer permitted to use the name of the SCM The approval holder and the supplier are obliged to first show the SCM copies of printing proofs of publications in which the SCM name is used other than in the term SCM approved for its assess ment If the publication does not fulfil the stipulations the
23. g arrangements may be made in this regard 4 6 3 Supplying recertification samples On behalf of recertification products must be made available within 6 weeks after announcement by the SCM by the approval holder to the testing institute 4 6 4 Random sampling control In addition to standard production controls the SCM retains the right should the situation call for this to have approvals carried out of SCM approved products originating in the market The costs of these approvals are for the account of the SCM 4 6 5 Prices of recertification The testing institute shall invoice the approval holder for the costs of recertification without the intervention of the SCM 4 6 6 Procedures in case of deviations defects in products 4 6 6 1 If the product is changed without notice If one of the products as a result of changes not announced in advance proves not to correspond with the SCM approved model the SCM has the right to deny the approval holder further use of the SCM name the approval of the relevant model of product may then be revoked 4 6 6 2 If a product fails approval If one of the products fails the tests to which it is subjected the SCM has the right to temporarily deny SCM Homologation Directive MP03 2003 Version 1 15 the approval holder use of the SCM name blocking the issue of labels shall be suspended immediately If approval is blocked the approval holder must Immediately commence an investigation t
24. hnical requirements that are set with respect to products to be certified according to these Homologation Directive are described In the Description of tests the conditions execution and various equipment of the various tests are described Should there be any unclear points or differences in English version the Dutch version shall prevail The laws of The Netherlands apply to all contracts SCM Homologation Directive MP03 2003 Version 1 2 SCOPE 2 1 General The requirements set in these conditions apply to electro mechanical anti theft products for vehicles and parts of vessels They replace the existing guidelines MPO1 SCM MBB 01 MBC 01 and BBM 01 VIP TNO The most important changes in MP 03 in comparison to MP01 MBB 01 MBC 01 and BBM 01 are the following e The new homologation directives offer the option of testing and certification by several accredit ed testing institutes as long as these meet requirements and have established a contract with the SCM e Ifa certified product can be extended by an accessory ies such that the object to be secured can be fastened to the solid world the sign plus is added to the approval number see also Ap pendix 3 par 4 2 Garaging element e The test procedures in particular attack tests are coordinated as much as possible with the practical possibilities e The validity of a approval terminates after 3 years e Extension is only possible if the p
25. ication If the application concerns a manufacturer outside the European Union the manufacturer will authorise a legal person established in the European Union to file the application for him 4 2 3 Products and documents to be submitted For the type approval at least 8 products one of them in parts must be made available to the testing institute one of which will be stored as a reference sample At least the following information must be supplied to the testing institute e The commercial documentation on the product including all usage options to determine whether there are functions that are not permitted in the context of this Homologation Directive and that can be activated by the user e User s manual and assembly instructions possibly in draft form e Complete technical documentation of the product offered For ex factory products other arrangements may be made with the testing institute in this regard e Statement concerning identification of product date and product series of the product to facilitate tracing 4 2 4 The test report If the results are positive the applicant can have the test report sent to the SCM This report must contain at least the following Specification of the version of the Homologation Directive used as well as the Annex es used Product description applications of the product Name of the client Name of the approval holder Name of the responsible testing engineer Definitive user s
26. ls These new Homologation Directive MP03 replace the existing guidelines of the NCP formerly VIP TNO and the SCM This concerns the following labels of approval e MBB 01 Mechanical Security Systems for Industrial Vehicles VIP TNO trucks trailers containers e MBC 01 Mechanical Security Systems for Caravans VIP TNO trailers boat trailers caravans horse trailers etc e BBM O01 Security Systems for Outboard Motors VIP TNO outboard motors starters of stern motors and expensive parts such as screws In addition the existing SCM TNO label of approval for private vehicle security systems is also being replaced e MPO1 Mechanical security systems for private automobiles Mechanical security systems with approval as per the 4 homologation directives mentioned above become invalid 12 months after the commencement date of the new Homologation Directive MP 03 The Homologation Directive can be divided into three parts Scope definition of terms and administrative requirements Chapters 2 4 Approval requirements Chapter 5 Description of the tests Chapter 6 In the Scope definition of terms and administrative requirements the definitions of terms are given and the procedures and conditions are described that apply to type approval and the production phase of SCM approved products Requirements are also set with respect to the manufacturer importer of SCM approved products In the Approval requirements the tec
27. manual and assembly instructions Conclusion Appendix ices containing the test results Photo of the product in colour If desired these can also be sent to the SCM later separately 4 2 5 The approval agreement After inspection of the approval report the SCM will send the a Certificate of approval to the appli cant Before the product with its SCM approval is placed on The List and labels of approval can be provided SCM Homologation Directive MP03 2003 Version 1 the approval holder and the supplier must enter into an approval contract with the SCM The rights and responsibilities of the SCM and the approval holder supplier are delineated in the approval contract An example of this contract can be found in appendix 1 4 2 6 Rights and responsibilities of the approval holder supplier Within the limits as specified in these guidelines the approval holder supplier has the following rights and responsibilities To be authorised to use the name SCM To be included in the SCM approved products on the List to be published by the SCM To mandatory provide all SCM approved products meant for the Dutch market with the SCM label of approval or have this done In case of ex factory products this stipulation may be deviated from in consultation with the SCM To mandatory report in advance in writing every technical change in production that might have an influence upon the approval to the SCM and the testing institute
28. o determine whether deviations are occurring during production or in the materials being used and correct these immediately if necessary He must send a written report to the testing institute within 14 days of the investigation on the investiga tion he has carried out the findings and the measures that were taken Have the tests that were not passed repeated by the testing institute at the expense of the approv al holder on three other products from the same production series recertification If all three products pass this recertification the possible temporary denial of the use of the SCM name shall be reversed deblocking and the issue of labels shall recommence If one or more of these three products fails recertification the SCM shall withdraw its approval from the approval holder and forbid its further use of the SCM name for the relevant model of product 4 7 Revocation of type approval If the approval holder does not adhere to the stipulations as set in this Homologation Directive approval may be revoked effective immediately possibly after consultation between the testing institute and the SCM This revocation applies to all products falling under the same acceptance number A revocation of approval means that all rights of the approval holder as described in paragraph 4 2 6 of this Homologa tion Directive are revoked effective immediately SCM Homologation Directive MP03 2003 Version 1 16 5 APPROVAL REQUIREMENT
29. rage element object mounted to the fixed world offering a possibility to lock a vehicle to this fixed world Anchorage elements do not have to include a lock Blocking elements pin or plate shaped metal parts in the key mechanism that facilitate actual locking Blocking unit system of closing pin and closing socket Blocking mechanism part of the lock that is directly moved by the key mechanism Cylinder system of cylinder core and cylinder housing Cylinder housing permanent part of the cylinder in which the blocking of the cylinder core takes place Cylinder core movable part of the cylinder in which the blocking of the cylinder core takes place Electronic key key that in addition to allowing normal access to the lock is also suitable for opening the lock electronically Approved lock a lock that fulfils all stipulations and requirements of these homologation directive Padlock a lock whose main characteristic is that it consists of a rigid portion clamp and lock housing or a lock block that cannot be separated from it with which it is possible to connect parts of a vehicle or vessel to each other or to a lock product or to a fixed object the solid ground Master key key with which it is possible to open a group of locks each of which also has its own unique key Profile projection of the vertical diameter of the key Key mechanical coded metal instrument that only fits into the key mechanism to which it belongs
30. ready equipped The object is thus fastened to the solid ground Lock products with which this is possible and which are supplied with a garaging element and with a chain if applica ble are given the sign plus as evidence of this as an addition to their approval number Wheel clamp a mechanism that can be locked around the entire wheel or around the rim and tyre such that the locked wheel can no longer move freely thus preventing the object from being taken away by an unauthorised person SCM Homologation Directive MP03 2003 Version 1 25 Appendix 4 Specific stipulations and requirements for mechanical security systems for outboard motors for pleasure craft B 4 1 General An anti theft locking system of an outboard motor a stern drive or a screw ensures that these products can only be taken away with force and making use of special tools Outboard motors are usually fastened to the mirror or in the well of a ship The mirror or well can be made of various types of material such as wood metal polyester or a combination of these Motors with a motor capacity less than approximately 40 HP are generally fastened with a system involving clamp screws that can be tightened by hand with clamping plates pressing against the inside of the mirror Motors with a greater capacity are usually fastened with the aid of a structure with clamping bolts that go through the mirror B4 2 Lock type definitions Outboard motor lock a mech
31. roduct meets the requirements applicable at that time e During the obligatory annual recertification attack tests are carried out in the same way as they were for the original approval e The role distribution between the testing institute in particular and the certifying institute has been changed the certifying institute takes decisions concerning approval and revoking approval e The certifying institute issues a certificate upon approval Parts of vehicles or vessels that are an indirect or direct part of the security product are considerd as parts of the product and must also be presented for approval All product parts must meet the Homologation Requirements and must always be delivered complete The model specifications and or the brand name under which the approval is issued must be clearly stated on the most important part s If the product or a product part is integrated with equipment meant for other purposes then this equip ment insofar as it has an influence upon the functioning of the product must meet the homologation requirements 2 2 Entrance date and term of validity of the Homologation Directive The commencement date of the Homologation Directive MP03 is 1 February 2003 As of that date the current directives become null and void Existing approvals under MP01 MBB 01 MBC 01 and BBM 01 remain in effect until 1 January 2004 The approvals granted under this Homologation Directive remain valid for at most 3 years
32. th regard to clutch locks special attention must be paid to that stipulated in 94 20 EC and ECE R55 2 5 Documents The product must be delivered with a user s manual and assembly instructions that are attuned to the product delivered and this must be at least in the Dutch language The user s manual must contain at least the following operating conditions operating instructions what to do in case of defects or malfunctioning overview of the product parts that are relevant for the user The assembly instructions must contain at least the following superimposition of the product parts installation diagram periodic maintenance with checklist an overview of the product parts SCM Homologation Directive MP03 2003 Version 1 7 3 DEFINITITIONS 3 1 Definitions 3 1 1 General Lock anti theft provision for two wheeled vehicles Permanently mounted lock a lock mounted by the manufacturer or after market on the cessel or vehicle and can be considered as part of it Non permanently mounted lock a lock which is no part of the vessel or vehicle and which is detacha ble without the use of any tools other than a key A feature of not permanently mounted locks mostly is that they enable the user to connect his vehicle to another vehicle or to an object which is connected with the fixed world tree fence lamppost If this is the case the sign plus is added to the approval label 3 1 2 Technical Ancho
33. ther attachments can in principle be divided into 2 categories Security systems to prevent unwanted hooking up or disconnecting of parts of a combination Security systems to prevent the unwanted moving of the object such as e Wheel clamps e Blocking turning supports e Possible combinations of the above named equipment with a garaging element B 3 2 Key type definitions Clutch lock also known as shaft lock a mechanism that goes around the clutch of the shaft or is built into the clutch that can be locked and that when locked will prevent the trailer or caravan or other attachment from being taken away by an unauthorised person Block of turning supports a product that is intended to somewhat lift a trailer or caravan or other attachment and to place it water level so that it can be locked in that position and thus prevents the trailer or caravan or other attachment from being taken away by an un authorised person Anchoring element an anchor that is poured or plastered into the floor and or wall of a storage room or garage or that is built into the paving such that it can only be removed with a great amount of effort the goal of which is that an object can be attached to it That object can be attached to it in that a part of for example the shaft falls into the anchor which is then locked or in that for example a chain with a lock makes a connection be tween the anchor and the object or a lock product with which the object is al
34. wheel clamps With these products it is not possible to turn the steering wheel more than one half turn They also hinder the removal of the steering wheel e Wheel clamps A mechanism that can be locked around the entire wheel or around the rim and tyre so that the locked wheel can no longer turn freely thus ensuring that the vehicle cannot be taken away by an unauthorised person Combinations of the above equipment This includes products that affect several parts of the vehicle such as the steering wheel pedal The same requirements apply to these as to separate products SCM Homologation Directive MP03 2003 Version 1 27 Certificate of approval e Incase of a Dutch Testhouse e Incase of a European Testhouse e Incase of a non European Testhouse Approval Agreement Fee Approval labels Independent of order size N B All tariffs are excl VAT SCM Homologation Directive MP03 2003 Version 1 Appendix 6 Zero Euro 500 to be determined Euro 250 Euro 0 10 28
35. where the type approval was carried out To mandatory adhere to the requirements with regard to the recertification of SCM approved products To mandatory provide if applicable the packaging of the security product with the SCM label of approval including a specification of the classification of the product 4 2 7 Guarantee repairs and provision of service The following requirements apply with respect to the business operations of the supplier who supplies the SCM approved product in the Netherlands e All products that he supplies will be repaired free of charge or replaced by the same product or one of equal value within the guarantee period this being at least 1 year to be calculated com mencing on the date upon which they are placed into operation Repair or replacement must be effected within 10 workdays e All products supplied must be able to be repaired or replaced for a period of five years after their purchase date Repair or replacement must be effected within 10 workdays e Should it be decided to cease supplying a product to the market the above mentioned service must be continued for 5 years If for any reason whatsoever the SCM product begins to be mar keted by another supplier the new supplier shall fully assume the above mentioned service obli gations for all products already on the market and shall sign a new approval contract together with the approval holder e Training and dealer support Helpdesk support
Download Pdf Manuals
Related Search