Controller - Partysound
Contents
1. Controller User s Manual Thank you for choosing our product please carefully read this manual and operate it obey the specification in order to make sure you can correct and safety installing operating and maintaining it We will not take any responsibility for the damage and body injury which caused by the abnormal operation A0 Preface This Manual includes the important information of installation ave operation Please install and operate the controller according to the instructions strictly And it must be power off when open the controller or before repair A Please read the complete contents of this manual please keep this manual attach with the controller for any preview B In order to make sure the correct and safety installation operation and maintenance well know and follow to the instructions of Manual is necessary C We will not take any responsibility to the controller damage property loss or body injure which caused by the incorrect installation operation and maintenance NOTICE The data which inside the Manual maybe changed due to the continuous improvement and we ll not make another notice We will keep the right to any specification update during improvement Packing Content accessories 1 AC adapter 1PCS 2 Signal Cable 1PCS 3 User s manual 1PCS 4 Maintenance Card 1PCS Unpacking Instruction Please check if all the contents are completed after unpacking then check if the controller is un2. Programming example edit the lamp to run the program more than 8 SCENES first the address of the specified lamp code such as the address code is 001 The console is programmed state which is programmed in the flickering light a Click SCANNERS 1 key making next to the green LED light Then edit BANK 1 of 8SCI NES adjust the sliding potentiometer different channel output state When set toa satisfactory output state click the MIDI ADD button and then click SCENE 1 button this time all the lights flashing three indicated that they had programmed the first SCENE Edit the same way as the other seven SCENES b Through the key to select BANK 2 and then edit the BANK 2 of 8 SCENES PEA A VALLE adjust the sliding potentiometer different channel output state When settoa satisfactory output state click the MIDI ADD button and then click SCENE 1 button this time all the lights flashing three indicated that they had programmed the first SCENE Edit the same way as the other seven SCENES c Select store where one of the CHASE for example stored in CHASE1 press CHASE1 key the first digital tube will display one d Through the key to select BANK 1 click the Music Bank copy button then click the MIDI ADD this time all three said that it had flashing lights BANK 1 stored in Chase e Through the f key to select BANK 2 click the Music Bank copy button then click the MIDI ADD this time all three said that it
3. 12 change to step 1 analogy B Delete a step in Chase Delete a step in Chase select the delete step if we delete the first step 10 use or key to select to the step 10 press Auto Del button the first step 10 has been deleted the f step 11 change into step 10 step 12 become to 11 analogy Delete a Chase select the Chase need to delete 2 hold down Auto Del button press the Chase which has been deleted again SCENES itself in the chase still exists Delete all Chase all the SCENE itself still exists 1 Turn off the power press Auto Del button and button at the same time 2 Close power all the lights flashing three times indicated they had been deleted at this time 6 ae SCENES Running Turn the power on it is in manual running mode Digital tube display 101 this time notin the programming state To control the lamp shall press Program button 2 seconds after the flashing light blink can be programmed At this point adjust each channel potentiometer lamp will be run accordingly If in the programming state press the Program button 2 seconds programming lights off Blackout indicator light this time enter into the Blackout state Press the Blackout button to exit Blackout state and then press the Auto Del button again the console automatically run the program Ifa BANK where without any programming SCENES then SCENES will not run the console only run the programmed SCENES of a BANK If a channel
4. 6 click the Music Bank copy button then click the MIDI ADD this time all three said that it had flashing lights BANK 6 stored in Chase1 h At this point press the Program button and then press and hold 2 seconds the console from the Program state to Blackout state while the first one shows a digital control will disappear according to Blackout key to exit Blackout status And press the Chase1 press Auto Del button the console will run is stored in the Chase1 in 48 SCENES MIDI channel set up and operation MIDI channel settings Hold down the MIDI button 2 seconds the third and fourth digital pipe flashing press keyand keys to select a MIDI channel 01 16 2 and then hold down the MIDI button 2 seconds to end the MIDI channel settings the new MIDI channel is stored you can also press the keyaddition keys away from any one of keys to come the new MIDI channel will not be stored 2 MIDl operation NOTE ON Receive NOTE ON signals implement the corresponding functions BANK NOTE NUMBER FUNCTION 00 TURN ON TURN OFF SC O1 TURN ON TURN OFF SC 02 TURN ON TURN OFF SC BANKI 03 TURN ON TURN OFF SC 04 TURN ON TURN OFF SC 05 TURN ON TURN OFF SC 06 TURN ON TURN OFF SC 07 TURN ON TURN OFF SCENE8 08 iB TURN ON TURN OFF SCENE1 BANK2 09 _ TURN ON TURN OFF SCENE2 10 TURN O URN OFF SC ai i 112 TURN ON TURN OFF
5. SCENE1 113 TURN ON TURN OFF SCENE2 114 TURN ON TURN OFF SCENE3 BANK15 115 TURN ON TURN OFF SCENE4 116 C TURN ON TURN OFF SCENE5 9 OAD LM URN ON TURN OFF SCENE6 118 TURN ON TURN OFF SCENE7 119 TURN ON TURN OFF SCENE8 120 TURN ON TURN OFF SCENE1 i 124 TURN ON TURN OFF SCENE1 122 TURN ON TURN OFF SCENE2 CHASE 23 TURN ON TURN OFF SCENE3 194 TURN ON TURN OFF SCENES 25 TURN ON TURN OFF SCENEG L 126 BACKOUT Maintenance Cleaning and Using Frequency of Product In the open the control stations or maintenance work before they begin to make sure the console power supply disconnected the console s internal use vacuum cleaner at least once a year Complain 1 The salesman will check the details of complained problem included the item no delivered quantity delivery time faultyand pictures and the requirement of customer 2 QC and Technology department will analysis the complained problem and givea final solution to customer Faulty Disposal Faulty Description Solution 1 Check if the power is correctly connected 2 Check if the 12V or 5V is short circuited Single or multiple channel failurg 1 check if the sliding potentiometer aging ordamaged Single or multiple keys failure 1 Check if the aging or keys damaged control doesn t work 10
6. had flashing lights BANK 2 stored in Chase1 f Hold down the keyboard and then press the Program at this time 2 seconds the console from the Program state to Blackout state while the first one shows a digital control will disappear according to Blackout key to exit Blackout status g And press the Chase1 press Auto Del button the console will run is stored in the Chase in 16 SCENES editthe address code of the lampisrunninga different or the same scene indifferentprocedures 1 set up two different address code of lamps such as the address code is set to 001 and 017 respectively 2 First edit the address code to run the lamp for the 001 scenario a Click SCANNERS 1 key making next to the green LED light Thenedit BANK 1 of 8 SCENES adjust the sliding potentiometer different channel outputstate When set toa satisfactory output state click the MIDI ADD button and thenclick SCENE 1 button this time all the lights flashing three indicated that they had programmed the first SCENE Edit the same way as the other seven SCENES b Through the 1 key to select BANK 2 and then edit the BANK 2 of 8 SCENES adjust the sliding potentiometer different channel output state When settoa satisfactory output state click the MIDI ADD button and then click SCENE 1 button this time all the lights flashing three indicated that they had programmed the firstSCENE Edit the same way as the other seven SCENES 3 And then edit the address cod
7. potentiometer Regulator adjustable potentiometer to change the output range of the DMX channel the minimum is 0 the maximum is 255 or from 0 to 100 adjustable potentiometer 1 8 control continuous 8 channels Page Selector button Select Page A or Page B Page A is the former 8 channel of each SCANNER Page B is afterwards 8 channel of each SCANNER SPEED SLIDER Move the slider to adjust light speed FADE TIME SIDER Move the slider to adjust FADE TIME LED DISPLAY BANK button 1 1 The third and fourth digital tube display BANKS 01 30 press the keys BANK increase or decrease the display SCENE is the SCENE of BANK Chase1 Chase6 button Used to Chases program or the choice of Chases operation Program button Turn the power on itis in manual mode press PROGRAM for 2 seconds corresponding programming light flashes SCENE and CHASE are ready to be programmed press PROGRAM for 2 seconds once more programming light goes out return to run mode Midi add button A Press Midi button for 2s when running the third and fourth digital tube flash select channel by t or press Midi button for 2s again end the settings options of the Midi channel the Midi channel is stored or any button can end the setting of Midi channel except 7 or 7 and do not store the selected Midi channel B Used to program when under programming mode A uto Del button A Jn running mode press Auto Del button automatically trigger indicator light which indi
8. programming and CHASE runnyng manual control and renote control 8 Fade Time control 9 DMX polarity selects Appearance use the streamline design Technology Parameter AC adapter Input Voltage AC 100 240V 60Hz 50Hz Output Voltage and current 9V 1 0A Outline Size 48 2x13 2x7cm Packing Size 57x 17 5x9cm N W 2 4Kg G W 3Kg Installation Installation First put the controller on the special desk and then connect the controller and the light through the signal line Connection of AC adapter The exclusive AC adapter should be used between the connection of controller and power and please confirm if the rated voltage and frequency is accordance with the power supply Parameter of Input Voltage and Frequency Voltage AC100 240V Frequency 60Hz 50Hz Operation Production Introduction 1 There is 192 DMX channel adjusting output level in every SCENE 2 8 SCENES are available to be programmed for each BANK When SCENE running all programmed SCENE of one BANK will be executed continuously in a cycle 3 Select bank using and button Also you can select desired bank using MIDI signals through MIDI interface there are totally 30 banks once only one can be chose 4 SCENES can be executed automatically and the duration is dependent on TAP SYNC DISPLAY scenes are executed under music or NOTE triggering also press ascene buttons by hand to run scenes 5 There are total 6 chases each con
9. cates under automatic trigger mode press Auto Del button again to withdraw automatic trigger mode automatically trigger indicator light goes out B Used to SCENE and Chase program when in programming mode Music Bank copy button A in running mode press Music button the sound triggers indicator light the SCENES can be triggered by sound press Music button again the sound triggers the indicator light off exit the sound trigger state B Used to SCENE and Chase program under programming mode Tapsync Display button A In AUTO running mode the running speed of scene is decided by the last pressing of Tapsync Display button Max 10 minutes zoo anuma B Not in AUTO mode conversion 0 255 or 0 100 Blackout button Ban on all of the channel output But does not affect a variety of operations and then click the Blackout key to exit the Blackout mode MIDI input Midi signal input DMX polarity select Select DMX polarity of the output DMxX output DMX 512 signal output DC Power input DC9 12V 300mA min Flash control output interface Hole down the flash control button next to the red LED will blink 2 second Flash signal button Through the audio signal lines and the audio jack of the flash connection Appendix SCENES Program Press PROGRAM for 2 seconds entre programming state programming light flashes SECNE PTOGRAMMING the maximum is 8 SCENES of a BANK 1 Press SCANNER key to select DMX channel Choose 8 or more channe
10. controlled by the adjustable potentiometer SCENES channel run will not be programmed value if adjustable potentiometer control is prohibited ie the potentiometer putter is in the most bottom then SCENE run the channel programmed value MANUAL RUNNING 1 AUTO TRIGGER LED and MUISC TRIGGER LED lights are all off 2 select a BANK use Tor button or through the Midi interface use the Midi signal to select 3 press SCENE button to run A SCENE 4 use Midi signal to run SCENE AUTO RUNNING 1 Press the Auto Del button automatically trigger indicator light bright 2 Press Auto Del button again exit automatic running mode SOUND RUNNING 1 Press the Music Bank copy button the sound triggers light bright SCENES run by Sound Control 2 choose the BANK to run can be controlled by manually or the Midi signal 3 click the Music Bank copy button again exit the sound running mode 4 MIDI RUNNING Select BANK and SCENES to run by MIDI signal whenever it is in manual running auto running or sound running CHASE RUNNING 1 it has been programmed Chase when the Chase running SCL NI automatically stop running 2 Chase running also has auto running or sound running and Midi running 3 you can also a Chase or multiple Chase to run first selected the first run 4 Press the Chase button Chase is running the first LED display the running Chase OUTPUT DELAY ADJUST Adjust FADE TIME potentiometer the output follows chanqes
11. damaged Please you can keep the original package and return to the factory if it s damaged AC Power Check whether the voltage is accordance with the rated power Safety Specifications all the safety items of operation includes installation and before operating 1 Unpacking the carton and take out all the accessories and open the poly package take out the light from the carton and put it in a certain platform for operation 2 The controller must keep dry and avoid to use under the Moist Overheat or Dusty surroundings And keep it far away from the water or other liquid 3 The installation operation and maintenance must be managed by the qualified professional and make sure to operate it under the instruction of the Manual 4 Please check if the voltage is accordance with the rated power before installing Notice Please make sure it s power off before any installation repair and clean Introduction Controller Channels 192 channels Display 1 4 digits LED display 2 Fird digit of LED shows CHASES the second digit of LED shows scenes 3 Third and fourth digit of LED shows BANKS 4 The second third fourth digit of LED show steps or 0 255 or TIME Additional Function 1 30 Banks each composed of 8 programmable scencs 2 8 fades adjusting output level 3 Built in Microphone 4 AUTO mode is controlled by TAP SYNC and SPEED controlled 5 MIDI control through MIDI interface 6 Blackout master controlled by M annual or R emote 7 CHASE
12. e to run the lamp for the 017 scenario a Click SCANNERS 2 buttons making next to the green LED light Through the 7 key to select BANK 3 and then edit the BANK 3 of 8 SCENES adjust the sliding potentiometer different channel output state When set toa satisfactory output state click the MIDI ADD button and then click SCENE 1 button this time all the lights flashing three indicated that they had programmed the first SCENE Edit the same way as the other seven SCENES b Through the key to select BANK 4 and then edit the BANK 4 of 8 SCENES adjust the sliding potentiometer different channel output state When set to a satisfactory output state click the MIDI ADD button and then click SCENE 1 button this time all the lights flashing three indicated that they had programmed the first SCENE Edit the same way as the other seven SCENES 4 Edit Address Code for the 001 and017 of the lamp to run the same scenario a Respectively Click SCANNERS 1 SCANNERS 2 button making the green LED light next to the corresponding Through the key to select BANK 5 and then edit the BANK 5 of the 8 SCENES adjust the sliding potentiometer different channel output state When set to a satisfactory output state click the MIDI ADD button and then click SCENE 1 button this time all the lights flashing three indicated that they had programmed the first SCENE Edit the same way as the other seven SCENES b Through the 7 key to select BANK 6 and t
13. elete a BANK select the BANK which need to delete press Auto Del button and Music Bank copy button at the same time CHASES PROGRAMM f the programming state can be directly CHASE programming if not programmed state hold down the Program button 2 seconds to enter programming state programmed indicator light flashs Program a SCENE to CHASE 1 the maximum of a Chase is 240 SCENES thatis 240STEPS 2 during running first programmed SCENES run first 3 select a Chase 4 select the SCENES of a BANK must have been programmed SCENE 5 press Midi add button Copy a BANK to Chase the maximum of a Chase is 30 BANK 1 select a Chase to store BANK 2 selecta BANK press Music Bank copy button 3 press Midi add button again Chase adds the programmed SCENES of the BANK Program a Chase A Add a step in Chase 1 convert the STEP display of the chase and BANK and SCENE display press Tapsync Display button show Chase and the programmed steps of the Chase press Tapsync Display button again show SCENE and BANK of Chase 2 Add a step in Chase press Tapsync Display show the programmed steps of the Chas if you have programmed 15 steps add a step between step 9 and step 1Ouse f or to select step 9 press Midi add buttonthe second digital tube display SCENE the third the fourth digital tube display BANK select the desired SCENE press Midi add button the selected SCENE has been added to step10 while the original step10 change to step11 step
14. hen edit the BANK 6 of the 8 SCENES adjust the sliding potentiometer different channel output state When settoa satisfactory output state click the MIDI ADD button and then click SCENE 1 button this time all the lights as HMM N flashing three indicated that they had programmed the first SCENE Edit the same way as the other seven SCENES 5 All edited BANK stored in the Chase a Select store where one of the CHASE for example stored in CHASE1 press CHASE1 key the first digital tube will display a b Through the key to select BANK 1 click the Music Bank copy button then click the MIDI ADD this time all three said that it had flashing lights BANK 1 stored in Chase1 c Through the key to select BANK 2 click the Music Bank copy button then click the MIDI ADD this time all three said that it had flashing lights BANK 2 stored in Chase1 d Through the key to select BANK 3 click the Music Bank copy button then click the MIDI ADD this time all three said that it had flashing lights BANK 3 stored in Chase1 e Through the 7 key to select BANK 4 click the Music Bank copy button then click the MIDI ADD this time all three said that it had flashing lights BANK 4 stored in Chase1 f Through the key to select BANK 5 click the Music Bank copy button then click the MIDI ADD this time all three said that it had flashing lights BANK 5 stored in Chase1 g Through the key to select BANK
15. ls every time 2 Select different channel to control several devices at the same time 3 Regulator adjustable potentiometer to set the output state when the output is set to a satisfactory state turn off the adjustable potentiometer 4 Select and adjust output level continuously until all devices are set 5 Press MIDI ADD button 6 Through button to select the BANK you need 7 Press SCENE button to strobe the SCENE SCENES Edit 1 Select need to edit the scene of a BANK 2 Use SCENE programming method to adjust to the requirement of device 3 Press MIDI ADD button 4 Press SCENE button to strobe the SCENE all indicated lights flash three time show that it had programmed the same below SCANNER COPY Supposed a SCANNER had set copy it to another SCANNER and then hold down the SCANNER which need to copy and press another SCANNER Copy a SCENE 1 select the SCENE which need to copy 2 press Midi add button 3 selecta BANK and then press the one need to copy to SCENE button Delete a SCENE set the value of the ALL DMX CHANNEL of the SCENE to 0 1 select the SCENE which need to delete 2 Hold down Auto Del button and then press the SCENE which need to delete Delete all of SCENE ALL DMX CHANNEL value is set to 0 1 turn off the power press Program button and button at the same time 2 closed the power AD 5 P Copy a BANK 1 select the BANK which need to copy 2 Press Music Bank copy button D
16. tains240 scenes You can choose CHASES Running one or more and MIDI signal remote controlling Pane button function introduction SCANNERS SCENES of tn a ve yall SCANNERS DMX channel buttons as the following list i Adjustable Computer light channel potentiometer LED control E 1 1 16 OFF p OFF 2 17 32 OFF OFF 3 33 48 OFF OFI 4 49 64 OFF OFF 5 65 80 OFF OFF 6 81 96 OFF OFF a 97 112 OFF OFF 8 11i 128 OFF OFF 9 129 144 OFF ORE 10 145 160 OFF OFE 11 161 176 OFF OFF 12 177 192 OFF OFF N Adjustable Computer light channel potentiometer LED ee control 1 1 16 o ON 2 17 32 _ ON ON 3 33 48 ON 4 49 64 O ON 5 65 80 O ON 6 81 96 ON ON 7 97 112 O ON 8 113 128 ON ON 9 129 144 ON ON 10 145 160 ON ON 11 161 176 ON ON 12 w782 ON ON Press SCANNER button corresponding LED is lit and the output of continuous 8 channels is enabled to be adjusted when SCENES are running if adjustable potentiometer control is OFF channel output level is not affected by the potentiometer if adjustable potentiometer control is ON channel output is changed correspondingly with the adjustable potentiometer SCENES button Press one SCENE button to run scene or to store and the second digital tube head display SCENES 1 8 Adjustable
Download Pdf Manuals
Related Search