LC8100 User Manual
Contents
1. 4 4 6 50 6 1 chools Materials See ete 6 2 6 2 Device Locatii 6 4 Electrical amp Installation Requirements 7 Bis The I VC Nace ata as cen ER 8 CONNECTIONS AND TURNING ON POWER 11 BIOSSET TING 2 12 TROUBLESHOOT G 14 SPECIFICATIONS os se seveccesscdvecsesesesttessdsedeesecesses scdctusesecesnteessstdeesecesseessssadesecssadeesdsadeesesscsesosseeavesecsseteossseases 16 LC8100 User Manual V1 0 OVERVIEW The Bematech LC8100 provides unparalleled reliability by being a fanless unit with no moving mechanical parts It is an ideal computer for use in harsh environments with high levels of dust or oil when fan noise is not desirable For m2. getting liquids inside the LC8100 If liquid does get inside have a qualified service technician check it before you power it on again e Unplug this product from the wall outlet before cleaning Do not use liquid cleaners or aerosol cleaners Use a damp cloth for cleaning e Werecommend all servicing done on this product be done by qualified service personnel e Aside from upgrades or swapping out the SSD or hard drive please refer all other servicing to the Bematech RMA Dept LC8100 User Manual V1 0 PRODUCT FEATURES o Fanless and ventless operation Intel Baytrail I E3825 1 33GHz dual core processor 1MB 12 Cache o Mass storage mSATA SSD no moving parts o Enclosed in rugged die cast case up to 4GB DDR3L SODIMM RAM No internal connecting cables with all components mounted on single PC board for high reliability Large number of available I O ports 5x USB 2 0 2x serial 1x VGA Ethernet 1x PS 2 keyboard and mouse speaker out and microphone in o Multimedia Video with 1920 x 1080 max resolution with 24 bit color ALC886 ALC892 Audio CODEC and built in 2W audio amplifier o System boot from SSD network or USB o Universal input 100 to 240VAC 47 to 63Hz switching power supply Ultra compact die cast housing only 2 H x 8 W x 6 D Integrated wall mount brackets o Custom configurations available LC8100 User Manual V1 0 INSTALLATION INSTRUCTIONS SAFETY TIPS Read these instructions c
3. that is released by holding the plug and pulling backwards If the connector is forced out by pulling the cable it may result in damage to the connector 9 Connect power cord to the power adapter and plug the power cord into AC power outlet The power adapter must be connected to the LC8100 first before it is connected to AC power outlet Do not connect AC power before connecting to LC8100 10 By default the unit is set to turn on power automatically when power is connected If it does not power up press the on off switch on the front panel to turn on power and check for correct CMOS configuration settings 11 If the LC8100 had been shutdown from the operating system it may be restarted by pressing the power on off switch on the front panel of the LC8100 To turn off power to the unit press and hold the power on off switch for 5 seconds 11 LC8100 User Manual V1 0 BIOS SETTING Each time the LC8100 is powered on it will run a self diagnostic and continue booting from storage media BIOS settings are stored in a CMOS memory To enter BIOS setup as soon as you hear the system beep just before LCI logo splash screen appears quickly press the Delete key on the keyboard Aptio Setup Utility Copyright C 2013 American Megatrends Inc Advanced Chipset Security Boot Save amp Exit BIOS Information BIOS Vendor American Megatrends Set the Date Use Tab to Core Version 5 0 0 9 0 09 x64 Switch between Date element
4. unit Heat is dissipated through the metal case So allow at least 6 inches of space from the top of the unit and 3 inches from the sides for proper ventilation 10 LC8100 User Manual V1 0 CONNECTIONS AND TURNING ON POWER Make sure that all systems are powered off before making or removing any connections to the LC8100 unit Follow the steps below in connecting the devices 1 Connect the VGA cable of the display monitor to the LC8100 2 Connect the RS232 cables of serial devices to the LC8100 3 Connect the parallel cable of parallel device to parallel port of LC8100 4 Connect the PS 2 keyboard or bump bar and mouse to the LC8100 Note that the bump bar cable connector has connector locking feature to prevent connector from being pulled out by pulling the cable When plugging in the connector grab the connector at the end of the plug and push in tightly until it is fully snapped into the socket Connect the Ethernet cable from Ethernet hub or switch to the LC8100 Connect other peripherals such as speakers and USB devices to the LC8100 Connect power to all peripheral devices and turn on power Connect power adapter to the LC8100 Make sure that the flat side of power plug is oriented upwards Reversing the orientation and forcefully plugging into the power socket will result in damage to the connector When unplugging power adapter from LC8100 do not pull the cable The connector has a locking function
5. MB L2 Cache Up to 4GB DDR3L SODIMM x1 Internal mSATA SSD 12VDC 100 to 240VAC 1 5A max 50 60Hz 12VDC 5A 3 3 Ibs 8 1 x 6 3 x 2 0 206mm x 160mm x 51mm Die cast Power Adapter Input USB Ports LC8100 User Manual V1 0 Serial Ports 1 and COM2 Keyboard Mouse Input I O PORTS Video Network Interface Keyboard Mouse USB Ports Serial Port Audio Expansion Slot ENVIRONMENT Operating temperature Relative humidity Storage temperature Relative humidity 16 VGA 1920x1080 pixels max 10 100 1000 Mbits Ethernet Network boot capable PS 2 mini DIN6 connectors USB 2 0 ports x5 DB9 x2 COM1 amp COM2 Optional 5V 12V power at pin 9 Mic in x2 and Speaker out x2 with 2W power amplifier Mini PCIe socket support WiFi card 09 to 40 C 5 to 90 non condensing 09 to 60 C 5 to 80 non condensing
6. arefully Save these instructions for future reference e Install this unit only in the manner intended by the manufacturer If you have questions contact the manufacturer e Installation measures must be taken to prevent physical damage to the power supply cord including proper routing of the power supply cord and provision of a receptacle socket outlet near the fixed ITE or positioning the fixed ITE near a receptacle socket outlet e Installation work and electrical wiring must be done by qualified person s in accordance with all applicable codes amp standards including fire rated construction e Don t attach power supply cable to the building surface or through walls ceilings floors and similar openings e Do not allow anything to rest on the power cord Do not locate this product where persons will walk on the cord e When cutting or drilling into wall or ceiling do not damage electrical wiring and other hidden utilities e Install the system away from sun rays vapor gases smoke humidity and suspended particles e Allow at least 6 inches of space from the top of the unit and 3 inches from the sides to allow proper ventilation This will be explained in the mounting instructions e If any problem occurs do not try to repair the equipment by yourself nor allow any unauthorized person to fix Contact the manufacture for assistance LC8100 User Manual V1 0 As a safety measure it is advised the use of a voltage s
7. ass storage solid state drive provides true no moving part operation In addition all components and connectors reside on one PC board thus no internal cables sources of common loose connections are required The computer is housed in a rugged die cast case for extra protection LC8100 has very compact form factor only 2 H x 8 W x 61 Two mounting brackets enable these units to be mounted almost anywhere on a wall ceiling table top or under a counter The LC8100 uses dual core Intel Baytrail processors so it can run Windows and Linux based applications This enables the unit to be used in a wide variety of applications The LC8100 also provides a very impressive compliment of up to date I O ports SVGA Ethernet parallel PS 2 and multiple USB and RS232 ports are all included Ask our Technical Support Team for more details on supported distributions LC8100 User Manual V1 0 CARE AND HANDLING The following tips will help keep your LC8100 functioning at the optimal level e Remember to unplug the display unit from the power outlet before cleaning e Do not use alcohol methyl ethyl or isopropyl or any strong dissolvent Do not use thinner or benzene abrasive cleaners or compressed air e To clean the LC8100 unit cabinet use a cloth lightly dampened with a mild detergent Do not immerse unit in water e Put the cleaner on the rag and wipe the LC8100 Never apply the cleaner directly on theLC8100 e Avoid
8. bematech LC8100 RETAIL HARDENED COMPUTER USER MANUAL LC8100 bematech LC8100 User Manual V1 0 NOTICE The manufacturer of the Industrial Computer makes no representations or warranties either expressed or implied by or with respect to anything in this manual and shall not be liable for any implied warranties of fitness for a particular purpose or for any indirect special or consequential damages Information in this document is subject to change without notice and does not represent a commitment on the part of the manufacturer FCC NOTICE This device complies with Part 15 of FCC Rules Operations are subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation BEMATECH International Division 999 S Oyster Bay Rd Building 104 Bethpage NY 11714 TEL 516 248 0400 FAX 516 248 0443 www bematechus com LC8100 User Manual V1 0 TABLE OF CONTENTS OVER VIEW 1 2 PRODUCT FEATURES siesecccsctesedsvssnssncasvancecsbcxanscdesuoudads ansoasasvondacesdenesetucensdavbcnenesdi saasssdoansawetseeaasesstavataneantine 3
9. e power adapter is properly plugged into a functioning AC outlet If the LC8100 is connected to a power supply but the power LED is off press the power button to turn on the unit If it does not turn on try replacing the power supply Replace the LC8100 if necessary Video monitor display is blue or frozen 1 2 3 Reset the LC8100 and check the system information on the screen during boot up If unit reboots correctly try running application again If same problem occurs try reinstalling the application software If unit cannot reboot correctly try replacing the hard disk drive or SSD Station is not communicating with server Application 1 2 Check that the LC8100 s IP addresses are correct and unique no conflict and the port number matches application software setup Check the Ethernet cable connections at the problem LC8100 s and at the Ethernet hub or switch Check that host server IP address matches the LC8100 IP address group Try pinging one of the LC8100 IP address from the host Check host server application software setup Restart software if necessary and test again Reboot the host server and test again Replace Ethernet hub or switch and test again LC8100 does not respond to keyboard commands 1 2 Check the keyboard cable connections at both the keyboard and the LC8100 Unplug the cable and re insert fully Check whether it snaps in correctly Note that it s necessary to hold the back e
10. ks on the equipment Install the equipment in a stable place with no vibrations Do not install the equipment on a mobile table with wheels 6 LC8100 User Manual V1 0 e The video monitor should be place strategically so that the lights of the room do not reflect the operator disturbing the correct visibility of the screen 4 Electrical amp Installation Requirements Electrical requirements It is the customer s responsibility to observe all governing codes and ordinances and assure that the electrical installation is adequate and in conformance with National Electrical Codes ANSI NFPA 70 latest edition or CSA Standards C22 1 94 Canadian Electrical Code Part 1 and 22 2 0 91 latest edition and all local codes and ordinances Have an electrical network with a ground connection with a three pin plug 2 poles and the ground in order to be compatible with the cable of the equipment Check that the voltage selector is in the position corresponding to the electrical provision Electrical network power supply 100 240 VAC 1 5A 50 60 Hz Before mounting the device please make sure that Mounting brackets are provided to facilitate mounting the LC8100 to a wall The installer should insure that the wall anchors used with the mounting brackets have the capacity to support 5 5 kg 12 This weight is determined by adding a safety margin weight to the weight of the unit Wall anchors with specified weigh
11. nd of the PS2 connector near the cable exit and push in hard to get the locking connector into place Test with known good keyboard and cable If it works replace the cable and or keyboard 14 LC8100 User Manual V1 0 Attached RS232 device is not working 1 2 3 Check whether baud rate and data format settings of application is matching with the 4 5 Check that the device and LC8100 have power Check RS232 connections at the device and LC8100 device Attach the wrap plug to the device end of the RS232 cable and run an RS232 port test program If the test passes replace the serial device If the test fails go to step 5 Attach a wrap plug to the RS232 port of the LC8100 and rerun the RS232 loop test If the test passes replace the RS232 cable If the test fails replace the LC8100 LC8100 does not boot from internal mSATA SSD 1 2 Check in BIOS setting whether the boot device priority is set to boot from mSATA note that the mSATA SSD is installed as SATA hard disk drive Check if the operating system on the mSATA SSD is corrupted If so try reinstalling the operating system or replace the mSATA SSD 15 SPECIFICATIONS Front View Back View SYSTEM CPU System Memory Mass Storage POWER SUPPLY Single power input Power adapter input Power adapter output MECHANICAL Weight Dimension WxDxH Housing Intel Baytrail I E3825 1 33GHz Dual Core processor with 1
12. rts For each serial ports option is available to select power function on pin 9 of the port e Disabled 5V e 12V Network boot If you desire to enable your system to boot from a network go to Advanced menu Then setup Network option to select UEFI only or Legacy only Save the settings and reboot into BIOS the network boot options will then be available Boot menu Restore to Optimized Defaults If the BIOS settings are accidently changed and it s necessary to restore setting to the optimized default values select menu Save amp Exit and then Restore Defaults Select Yes in the confirmation dialog box Then select Save Changes and Exit or press F10 to save the changes 13 LC8100 User Manual V1 0 TROUBLESHOOTING There are no user serviceable components inside the LC8100 Service should be performed only by Bematech or qualified personnel certified by Bematech The following guide lines will help in identifying the source of a problem Video monitor display is blank 1 ig If the power LED on the monitor is off check that the monitor is properly connected to its power supply and the power supply is properly plugged into a functioning AC outlet Adjust the contrast controls on the monitor display Check that the video cable is plugged in properly on both the monitor and the LC8100 If the power LED on LC8100 is off check that the LC8100 is properly connected to its power supply adapter and th
13. s Compliancy UEFI 2 3 PI 1 2 Project Version DMS 12 006 Build Date and Time 04 08 2014 09 24 38 System Date Wed 05 07 2014 System Time 17 11 06 Access Level Administrator gt Select Screen Select Item Enter Select Change Opt 1 General Help F2 Previous Values F9 Optimized Defaults 10 Save amp Exit ESG T EXIT Version 2 16 1242 Copyright C 2013 American Megatrends Inc Use left and right arrows to select the setup menu Use arrow keys to navigate to different menu items and press Enter to select menu Use keys to change the field value or press Enter to go to sub screen When configuration is finished press F10 key to save the settings and exit setup In most of the applications parameters are detected automatically the default configuration will be suitable There are only a few parameters that might need to be customized for some applications Examples of such cases are shown below 12 LC8100 User Manual V1 0 Boot Device Priority Sequence To specify the boot sequence from available devices enter the Boot menu Then setup Boot Option Priorities to choose the priority desired for the booting process from the list of available boot devices I O Configuration Serial and Parallel Ports To configure the serial ports go to Advanced menu Select Super IO Configuration and then you will be able to choose change the address and IRQ for all the po
14. t capacity are available commercially The power outlet socket is located near to the desired mounting location for the LC8100 5 1 LC8100 User Manual V1 0 Mounting The Device Mount the LC8100 horizontally with the mounting brackets Allow at least 6 inches of space from the top of the unit and 3 inches from the sides to allow proper ventilation See the picture below Minimum 6 Minimum 2 MES 1 Above Counter Push two mounting brackets outward and tighten the screws Picture 7 LC8100 User Manual V1 0 Picture 8 2 mount the LC8100 on the counter top with screws Picture 9 LC8100 User Manual V1 0 Mounting the LC8100 to the wall with the mounting brackets Allow at least 3 inches of space from the top of the unit and 6 inches from the sides to allow proper ventilation See the picture below z m 5 3 w r E 3 8 2 Minimum 6 Minimum 6 9 13 0 3 9 Jm 1 2211 Under Counter Under Counter 1 push two mounting brackets out gt See Picture 7 8 2 mount the LC8100 with wood screws 2 pieces 1 8 x 1 1 2 gt See picture 9 The screws must be driven on the wall studs or use drywall anchors if it is a dry wall Use concrete wall anchors 2 pieces 1 16 x 3 8 if it is a concrete wall The LC8100 is a fanless and ventless
15. t the Manufacture Service centers whenever necessary Don t try to replace the lithium battery cell under any circumstances There is risk of explosion if an incorrect type of lithium battery cell used Dispose of used batteries according to the instructions CAUTION Caution Risk of Explosion if battery is replaced by an incorrect type Ask manufacturer for technical service if the lithium battery cell need to be replaced WARNING LC8100 User Manual V1 0 COMPONENT PLACEMENT The following is recommended when you plan the LC8100 setup e Place the LC8100 so that 1 The RESET button is accessible 2 The beeps from the speakers can be heard 3 The LED indicator on the front panel can be seen e Place the LC8100 above grill counter level out of the way of possible spills e Leave enough spaces around the unit for ventilation MOUNTING INSTRUCTIONS 1 Tools Materials Required Wood screws 2 pieces 1 8 x 1 1 2 Concrete wall anchors 2 pieces 1 16 x 3 8 Measuring tape Electric drill with 5 16 and 3 8 Bits Phillips Screw driver Stud finder 2 Parts Parts included with the product package 1 LC8100 unit 2 DC power adaptor 3 Power cord Device Location The location of installation should meet the following conditions Have enough space for its operation and preventive and corrective maintenance Advisably the floor should not be wooden in order to avoid electrostatic shoc
16. tabilizer or UPS between the equipment and the line socket This product should be operated from the type of power indicated on the power adaptor If you are not sure of the type of power available consult your dealer or local power company The feeding line should be exclusive for the equipment unless it is used for other compatible equipment and it should not overpass the maximum consumption of the line Photocopy machines electrical motors and any other high consumption equipment should be installed isolated from this equipment If an extension cord is used with this product make sure that the total ampere rating of the equipment plugged into the extension cord does not exceed the extension cord ampere rating Also make sure that the total rating of all products plugged into the wall outlet does not exceed the fuse rating Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions If the power cord or plug is damaged or frayed If liquid has been spilled into the product If the product has been exposed to rain or water If the product does not operate properly when the operating instructions are followed If the product has been dropped or the cabinet has been damaged If the product exhibits a distinct change in performance indicating a need for service ON OI eS There is risk of electrical shock even with the wire disconnected from the electrical network Contac
Download Pdf Manuals
Related Search