Instrukcja ALFA RADIO_EN_2012_07_10.cdr
Contents
1. Wireless remote control system ALFA RADIO User s manual Read these instructions carefully before operating the screen Dear Customer Thank you very much for the purchase of our product The manual booklet contains all operation information you may require to install properly and operate the radio remote control system We hope it will help you to get the most enjoyment of your new control system Enjoy time with the Avers Screens product SAFETY INFORMATION NOTICE Important safety information Follow the instructions described in the operating manual for safety reasons After reading the manual please store itin a safe place just in case you need it in the future NOTICE THE DEVICE HAVE TO BE EARTHED WARNING 1 Disconnect the device from the power supply if it will not be used within longer period of time 2 Do not open the casing of the device in order to avoid possible electric shock There are not any user operated parts inside the case of the screen All service work can be done by Avers Authorized Service Center personnel only Table of contents 1 Safety rules 1 1 Declaration of Conformity CE 2 Product specification 2 1 Contents of package 2 2 Technical data 3 Control system installation 3 1 Installation directions 3 2 Control unit installation 3 3 Electric installation 3 4 Control system programming 4 Control system operation 4 1 Manual operation 4 2 Control system maintenanc2. 4 2 Control system maintenance ALFA RADIO remote control system does not require periodical service maintenance Clean dust from the control unit and trigger transmitter cases with dry soft cloths If needed use moisturized cloth with soft detergent to remove stains After stain removal dry the cleaned surface with cloth carefully Symptoms Reasons Remedy Power supply indicator red Lack of power supply Check the Control Unit s circuit fuse and do not light condition of the power cable Screen lift operates wihout Reaction to the commands from the remote Erase the Control Unit memory and any control signal transmitter of an other control system programm the transmitter again Cloned transmitter program as separate unit There is no reaction for the IR sensor is blinded by direct exposure to Remove interfering light source or change commands from the intensive light location of the control unit and wall switch transmitter Remote Transmitter battery has exhausted Replace the Remote Transmitter batery with a new one Defective Remote Transmitter Replace the Remote Transmitter In other cases please contact service 5 Warranty conditions 1 Avers control system warranty period is 24 months from the date of purchase confirmed with the original purchase Invoice 3 Surety commits to fix free of charge any failures component or production defects of the product which appear during warrant
3. Wersja 25 03 2012
4. attach manual wall switch with dedicated connection cable supplied with the switch as shown at the Picture 2 Connect the power cable to the Power Supply Terminal as shown at the Picture 2 Fix the cables with the securing profile and attach the Control Unit s front cover ALFA unit front panel removed Dedicated wall switch Screen lift cable bl blue common br brown rolling down yg yellow green protective bk black rolling up Power cable L1 brown live N blue neutral G yellow green protective Internal elements description 1 IR sensor 2 Power indicator red 3 Activity indicator green 4 Program button S4 5 Fuse 10A 6 Connection terminals control and power supply 7 Trigger input connector RJ9 8 Optional wall switch connector RJ12 o uona Aa ON a Dedicated connection cable Screen Lift 62 O 230 V Picture 2 ALFA RADIO control Unit electric instalation II ATTENTION Electric installation work should be carried out by a certified Electrician 3 4 AVERS RADIO control system programming Wireless remote control system ALFA Radio do not require any programming to operate first time It will be ready for use just after accomplishing electric installation of all components It is possible to use many ALFA RADIO systems in the same area They will operate without interfering each other as long as remote tran
5. cable holders Wall switch Picture 1 Alfa control unit wireless transmitter and Wall switch 3 Control system installation 3 1 Installation precautions Installation work should be carried out by a qualified technician in accordance with the instructions described below Fixed installation of the control system should be done with use of the screws and anchors suitable for the walls ceilings materials at the installation place 3 2 Control unit installation Appoint the location of the control unit fixing points see Appendix Drill holes for the fixing anchors Fix the control unit wall switch and remote transmitter holder with anchors 3 3 Electric installation Lead out the power and screen lift cables to the place of Control unit installation Screen power line should be fused with 10A fuse Switch off the Control unit power line during installation work Manual wall steering switch and remote transmitter bracket should be installed at the place meeting following conditions a installation 150 180cm above the floor level b the screen should be visible by the wall switch operator during the screen operation c wall switch operator cannot stay at reach of any of the screen s moving parts during the screen operation d the wall switch must be visible from the each part of the room irrespective of the screen position Connect the screen cable to the Control Terminal as shown at the Picture 2 Optionally
6. e 4 3 Before asking for service 5 Warranty conditions 1 SAFETY RULES SAFETY INFORMATION NOTICE Important safety information It is important for the safety of persons to follow these instructions After reading the manual please save it just in case of need in the future e Do not allow children to play with the wall manual switch connected to the control system e Keep the Control unit out of reach of children e Keep the batteries for the transmitter out of reach of children In case of suspicion of the battery was eated by a child seek medical advice immediately Do not allow the and terminals of the batteries to come into contact with metallic objects Failure to observe this may cause the batteries to leak overheat explode or catch fire e Frequently examine the control system installation for imbalance and signs of wear or damage to cables Do not use if repair or adjustment is necessary e Watch the moving screen and keep the people away until the screen is completely rolled in out It will help to avoid injuries caused with moving screen e Allinstallation work should be carried out by the qualified technician e Improper installation can cause device damage or health breakdown Do not do anything that may damage the power cables e Operation of the control system with damaged power cords can result with electric shock electric short circuit and fire e Do not touch the power cables and the control u
7. ll blink 3 times and turn off to confirm erasing memory of the Control Unit e Settings of all Transmitters have been erased 4 Control system operation ALFA RADIO wireless remote control system allows control of Avers electric projection screens models without integrated control system only and Prolift electric projector lifts Manual operation is possible either with the optional remote transmitters either with the optional dedicated wall switch either with emergency control buttons when other control options are inactive ALFA control unit and dedicated wall switch should be installed at areas secured from direct operation of sunlight or other strong light sources IR remote transmitters requires direct optical contact with IR receiver for operation they will not operate if any barier will be placed in between 4 1 Manual operation Manual screen operation is possible either with the optional wall switch either with the optional remote transmitter either with emergency control buttons Push button v activity indicator will turn on the screen lift engine will begin operation and it will stop automatically when bottom position of the screen lift will be reached Push button Stop activity indicator will turn on the screen lift engine will stop operation immediatelly Push button 4 the screen lift engine will begin operation and it will stop automatically when upper position of the screen lift will be reached
8. nit with wet hands Remove the battery from the remote transmitter each time you plan not to use the the system for a longer period of time Store the battery in a plastic bag e Always follow the instructions described in the operating manual 1 1 Declaration of Conformity CE AVERS SCREENS Manufacturer s Declaration of ConformityCE AVERS Screens Sp z 0 0 Under it s own responsibility declares All screensand accessories mentioned below are manufactured in Polandaccording to the essential safety requirements of Council Directive 98 79 WE Control systems ALFA TRIGGER WIRELESS ALFA TRIGGER ALFA IR ALFA RADIO BETA DELTA The above mentioned products are in conformity with the European Directives and especially with the norms PN EN 55014 1 2007 U PN EN 50082 1 1997 PN EN 60335 1 2004 PN EN 61000 3 2 2007 PN EN 61000 3 3 1997 IEC 60335 2 97 2007 CE 2 Product specification ALFA RADIO remote control system is dedicated for automatic remote control of electric projection screens by Avers Screens electric projector lifts Avers ProLift electric coutrtain system Avers VIRGO and other home electric appliances driven by applying high voltage to the control inputs The control system was designed for fixed installation at projection systems for business presentations and or home cinema applications Operation of controlled devices is done manually either with
9. smitters of each ALFA unit will not be memorized by any other ALFA unit ALFA unit can be controlled by unlimited number of ALFA IR transmitters Each ALFA control unit reacts to command send from any ALFA IR transmitter in range Additional IR transmitters do not require programming ALFA unit reacts to incoming commands immediately after command arrival Programming procedure described below have to be performed when the control system is upgraded with optional wireless remote transmitters i e ALFA RADIO PILOT ALFA RADIO SWITCH or ALFA WIRELESS TRIGGER ALFA control unit can remember up to 20 wireless remote transmitters they must be separately programmed at the ALFA control unit memory A Setting up of the new transmitter Control Unit can memorize 20 individual control codes of remote transmitters e Connect power supply to the Control Unit and pick up the transmitter e Press the Control Units emergency STOP button and hold pressed untill activity indicator will blink 5 times and will light green confirming the Control Unit has entered program mode e Press the transmitter 4 control button or wireless trigger transmitter P2 button and keep it until the activity indicator will stop lighting e Transmitter is stored at the ALFA control system now B Deleting of the Control Unit memory e Connect power supply to the control unit e Press and hold Control Unit emergency control buttons vw and STOP e Green indicator wi
10. the infrared remote transmitter either with the dedicated wall switch Dedicated wall swith should be connected to the control unit with cable In case of remote transmitter malfunction emergency control buttons located at the control unit allow manual operation It is possible to control several ALFA control units with single infrared remote transmitter 2 1 Contents of packaging Please check carefully if any physical damage of the control system has not happen during transportation Inspect the package for all accessories presented below x1 x1 GZ amp ALFA control unit connectors x1 x1 x1 x1 Wireless remote transmitter accessories O al x1 Ko x1 Wall switch dedicated connection cable Operation manual x 1 2 2 Technical Data Control Unit Dimensions 78 x 128 x 45 mm Power supply 220 240V AC 50Hz Control supply 220 240V AC 50Hz Max control current 10A ALFA control unit Wireless Transmitter Dimensions 110 x 58 x 20 mm Power supply battery 12V type 23A Operation range up to 7 m Wall switch depends on environmental conditions Wireless transmitter Dimensions 86 x 86 x 25 mm Power supply from ALFA unit Cable length 8m Operational elements 1 power indicator red 2 activity indicator green 3 emergency control button UP 4 emergency control button STOP 5 emergency control button DOWN 6 IR sensor 7
11. y period 4 Warranty exclusions a The failures caused by the usage of the control system against the rules described in operation manual b The failures caused by improper storage or transportation c Mechanical defects of the control system other than mentioned at point 3 d Damages caused with overvoltage at power network e De installation and reinstallation of the screen 5 Avers Screens Service department will remove all defects within 21 days after receiving the damaged product 6 Warranty claims should be passed to the screen supplier dealer Appendix Control unit installation template Apply the template at the place you intend to install the Control Unit and appoint the centers of holes for the fixing anchors Drill the holes in appointed places 49 vyl 72 O O I I CAUTION Check the holes printed at the template match the location of fixing points at the control unit before you use it Manufactured after 13 08 2005 This symbol on the products and or accompanying documents means that used electrical and electronic products should not be mixed with general household waste Disposing of this product correctly will help to save valuable resources and prevent any potentialnegative effects on human health and the environment which could otherwise arise from inappropriate waste handling Please contact your local authority for further details of your nearest designated collection point
Download Pdf Manuals
Related Search