PT1700MX / PT1710MX / PT1775S / PT1785P Touch
Contents
1. PLANAR PT1700MX PT1710MX PT1775S PT1785P Touch Screen LCD Monitors USER S GUIDE www planartouch com The information contained in this document is subject to change without notice This document contains proprietary information that is protected by copyright All rights are reserved No part of this document may be reproduced translated to another lan guage or stored in a retrieval system or transmitted by any means electronic mechanical photocopying recording or otherwise without prior written permission Windows is a registered trademark of Microsoft Inc Other brand or product names are trademarks of their respective holders Important Recycle Instructions Lamp s inside this product contains mercury This product may contain other electronic waste that can be hazardous if not disposed of properly Recycle or dispose in accordance with local state or federal Laws For more information contact the Electronic Industries Alliance at WWW EIAE ORG For lamp specific disposal information check WWW LAMPRECYCLE ORG For more information on how to recycle your product please visit WWW PLANARSYSTEMS COM GREEN Table of Contents USAGE NOCE T 3 CO 3 INTOQUCUO NY TT a About PT1700MX PT TIOTINDELPTDTIUL TOS aucitedmaniesv itn oda eia 4 Touch Screen for PT1700MX ese 5 TOUCH Screen OP 5 ee 9 To cM Screen Noo m 6 Package 8 7 EE 7 IS tall AU OR T 8 OOUeCGUE 8 WE 8 PT1700MX PT1701MX P2. isopropyl alcohol D Use a soft cloth moistened with mild detergent to clean the display housing D Use only high quality and safety approved AC DC adapter D Disconnect the power plug from AC outlet if the product is not going to be used for an extended period of time Don t D Do not touch the LCD Display screen surface with sharp or hard objects Do not use abrasive cleaners waxes or solvents for your cleaning a Do not operate the product under the following conditions Extremely hot cold or humid environment Areas susceptible to excessive dust and dirt Near any appliance generating a strong magnetic field In direct sunlight la Introduction About PT1700MX PT1701MX PT1775S PT1785P The PT1700MX PT1701MX PT1775S PT1785P is a 17 flat panel screen with an active matrix thin film transistor TFT liquid crystal display LCD Features include 2 Direct Analog signal input Active matrix TFT LCD technology 1280x1024 SXGA resolution 17 viewable display area 31 47 80 kHz horizontal scan 56 75 Hz high refresh rate 0 264mm x 0 264mm Pixel pitch Auto adjustment function Multilingual OSD user controls VESA DPMS power saving Kensington security slot 75 mm 100 mm VESA mount Removable base for flexible mounting solutions PT1700MX 5 wire resistive touch screen with dual RS 232 Serial USB controller a PT1701MX Capacitive touch screen with dual RS 232 Serial USB co
3. to the right of the model name 4 TheHID calibration tool will automatically open From here the user can choose to do the following a 4 Points Calibration b 9 Points Linearization c 25 Points Linearization d Clear e Draw Test f Advanced In the Advanced settings area the user may do the following i Adjust the Double Click Area li Enable auto right click and adjust the auto right click time lil Choose to be either in the HID Mouse Mode or HID Digitizer Mode Windows Vista and Windows 7 iv Simply click the Apply button once the settings are finalized 2f PT1785P Calibration Instructions Calibrating the touch screen in Windows 7 1 Tap the Start button Control Panel and then Hardware and Sound 2 Under Tablet PC Settings tap Calibrate the screen for pen or touch input 3 Onthe Display tab under Display options tap Calibrate and then Yes to allow the program to make changes 4 Follow the on screen instructions to calibrate the touch screen EE m eGalaxTuner Release Shortcut a y i Getting Started best Documents Windows Media Center s al Pictures sess Calculator eet Sticky Notes EA Snipping Tool Computer A emote Desktop Connection f bame Control Panel Solitaire anm Devices and E Magnifier N Default Programs k gage Microsoft Surface Collage Help and Support LI All Programs Adjust your computer s settings View by Cate
4. ISTA XP 2000 ME 98 NT4 0 CE XP Embedded Linux Apple Mac OS D D D U U U UD U Touch Screen for PT1785P QO Project capacitive touch screen for finger input only D Surface Glare treatment Interface USB controller Transmittance 90 5 Driver Windows 7 VISTA 64 32 bits XP 2000 XP Embedded Express Linux Apple Mac OS D D U LLL LLLLLL LLLLLLLLLLLLL LLL Z1 Package Overview Power Cord VGA Signal Cable USB Cable Type Ato B Audio in Cable RS 232 Cable PT1700MX PT1701MX PT1775S only Landing Strip Touch Screen Driver User s Guide Installation CD ROM O DC Power Supply Cable Cover Screw sold separately Installation Product Overview gt Front View PT1700MX PT1701MX PT1775S9S PI1 85P gt PT1700MX PT1701MX PT1775S Bottom View Without Stand AUDIO IN USB AC IN eo RS 232 DC IN gt PT1785P Bottom View Without Stand 9 Start Your Installation 1 Lay the LCD flat on an even surface 2 Remove the stand back cover by pulling in the direction of the arrow as seen in step 2 diagram 3 Move the stand into position as seen in step 3 diagram 4 Connect the cables to the appropriate connectors as seen in Step 4 diagram Use step 4 1 diagram if using the RS 232 serial connector Use step 4 2 diagram if using the USB connector 10 9 Take the optional cable cover and screw from the accessory box Positio
5. T1775S Bottom View 8 PI doc cag BOON VIW esiosas e 8 Start YOU WN Stall All OW ssrin a rE T 9 Connecting the Display Figure 12 11 sese 11 12 Aehsnolonmweco SO 13 VESA Mount VOUF MONOT sese ciae cute a EE Edu tdar Aeon Echec Rosendo on eet itus 14 REMOVE NE DOSKSIGNG EE 15 BA aT el iniuria UM ER EMIE DIENEN OHeE 16 ode Dalle eee 16 HOw to VSee DOSE eT 17 On Screen Display NemUS e eee eee eee 19 POD OCH GK E EEE EEE eR 20 FOUPIESNOOUN O remeron te ere mete eter oe een ener en een een ene cee ee eae 20 Nese o E E 21 POE er ere IE 21 GONGO SCOP Q 21 OQUO TANG Cassa risen dich tare E E E A T EE 21 FroOaUCT DIMENSIONS reris EE E EE 22 Compalibily Ooes a A EE 24 Touch Screen Driver Jnstallatioani es ee eee eee eee eee 25 Product Registration and Technical SUuUDDOOT e e ee ee eee e 31 Usage Notice AN Warning To prevent the risk of fire or shock hazards do not expose this product to rain or moisture AN Warning Please do not open or disassemble the product as this may cause electric shock Precautions Follow all warnings precautions and maintenance as recommended in this user s manual to maximize the life of your unit Do d Turn off the product before cleaning a Touch screen surface may be cleaned using a soft clean cloth moistened with mild window glass commercial cleaners or 50 50 mixture of water and
6. Tablet PC Settings Configures tablet vi ee ees for a Tablet PC Configure your pen and touch displays Display options Choose the order TW 29 PT1700MX PT1701MX PT1775S PT1785P Install Instructions If you are using a PC running Windows 7 VISTA XP 2000 ME 98 NT4 0 follow the instructions below 1 Poweron the PC 2 Besure the USB or the RS 232 Serial cable is connected from the PC to the LCD display Open the CD ROM Follow the step by step instructions as shown on the pop up windows If you are using a PC running Windows XP Embedded follow the instructions below Express 1 Power on the computer 2 Make sure that the RS232 or USB cable is connected to the computer 3 Be sure that your EWF is disabled If your EWF is enabled please disable the EWF by using the EWF Manager command 4 Once the EWF is disabled click on the XP driver on the CD ROM and follow the step by step instructions as shown on the pop up windows Custom PT1785P excluded 1 Power on the computer 2 Make sure that the RS232 or USB cable is connected to the computer 3 Follow the step by step instructions found in the zipped file on the CD ROM If you are using a PC running Windows CE follow the instructions below PT1785P excluded 1 Power on the computer 2 Make sure that the RS232 or USB cable is connected to the computer 3 Using Platform Builder build an image file by following the step by step instructio
7. al an 09 VESA XGA 56 48 70 VESA XGA 60 02 15 VESA SXGA 64 00 VESA SXGA 80 00 VESA SXGA 60 00 VESA SXGA 67 50 Apple Mac II 35 00 24 25 Touch Screen Driver Installation The PT1700MX PT1701MX PT1775S is available with both RS232 and USB connections The touch driver is located on the enclosed CD ROM for these operating systems Windows 7 VISTA 64 32 bits XP 2000 ME 98 NT4 0 CE XP Embedded Linux Apple Mac OS The PT1785P is available with USB connection The touch driver is located on the enclosed CD ROM for these operating systems Windows 7 VISTA 64 32 bits XP 2000 XP Embedded Express only Linux Apple Mac OS Please Note 1 The PT1700MX PT1701MX PT1775S PT1785P is Microsoft Windows HID Human Interface Device compatible if you use the USB touch screen interface No additional software driver is required for general operation of the touch screen 2 For PT1785P the system requires 15 seconds for Windows 7 to Install uninstall the touch driver while turning power on off or plugging unplugging USB cable PT1700MX PT1701MX PT1775S Optional Calibration Tool Install If you would like to use the Optional Calibration Tool follow the instructions below Please note the calibration tool supports Windows 7 VISTA XP XP Embedded 2000 98 and ME operating systems via USB only 1 Open the CD ROM 2 Select the monitor size and then model name 3 Click on the Load Utility button that appears
8. display mode is compatible with the LCD display We have listed the compatible Video Modes of your LCD display in the appendix for your reference Figure 12 1 gt PT1700MX PT1701MX PT1775S gt PT1785P 12 13 Kensington Security Slot The monitor can be secured to your desk or any other fixed object with Kensington lock security products The Kensington lock is not included e 7 e o a amp G a o gt i e e 14 VESA Mount Your Monitor This monitor conforms to the VESA Flat Panel Mounting Physical Mounting Interface standard which defines a physical mounting interface for flat panel monitors and corresponding with the standards of flat panel monitor mounting devices such as wall and table arms The VESA mounting interface is located on the back of your monitor To mount the monitor on a UL certified swing arm or other mounting fixture follow the instructions included with the mounting fixture to be used 100 0 mm _ Slots x4 A snl oss ll lall aes oo 1 VESA Mounting Interface AN Warning Please select the proper screws The distance between the back cover surface and the bottom of the screw hole is 8 mm Please use four M4 screws diameter with proper length to mount your monitor Please note the mounting stand must be able to support at least 13 2 Ibs 6Kg 18 Remove the Deskstand Remove stand back cover Remove hinge cover Remov
9. e 4 screws and then remove hinge 1G User Controls Side Panel Controls a uh a wh uh key Name Menu Lr A Up Down Enter o O0O oO OO O oO O Oo O oO d 5 Power UU Menu disappear return to main item Brightness Main item select up Adjust up Main item select down Adjust down Enter Select sub item function Power On Off 17 How to Use the OSD Menus 1 Press the MENU button to pop up the on screen menu and press Up or Down button to select among the six functions in the main menu 2 Choose the adjustment items by pressing the Enter button 3 Adjust the value of the adjustment items by pressing the Up or Down button 4 With the OSD menu on screen press Menu button to return main menu or exit OSD 5 The OSD menu will automatically close if you have left it idle for a pre set time 6 To Lock the OSD Power menu buttons please follow the instructions below Please note the monitor has to be turned ON with a valid signal pre set a Press Menu key the OSD menu will pops upon display b Press and hold the Menu key again with the OSD menu on the screen the OSD menu will disappear Then press the Power key 1 time while the menu key is still being pressed The Lock Unlock menu will appear for 3 seconds c Use the Enter key to select OSD or Pow
10. ent If this problem still exists use Horizontal size to make an adjustment 21 Warning Signal If you see warning messages on your LCD screen this means that the LCD display cannot receive a clean signal from the computer graphics card Below are the three kinds of Warning Signal Please check the cable connections or contact your local dealer or our service center for more information No Signal This message means that the LCD display has been powered on but it cannot receive any signal from the computer graphics card Check all the power switches power cables and VGA signal cable Going to Sleep The LCD display is under the power saving mode In addition the LCD display will enter power saving mode when experiencing a sudden signal disconnecting problem The monitor can be activated by pressing any keyboard triggering the mouse or touching the screen Out of Range This message means that the signal of the computer graphic card is not compatible with the LCD display When the signal is not included in the Video Modes list we have listed in the Appendices of this manual the LCD monitor will display this message 122 Product Dimensions PT1700MX PT1701MX PT1775S b Front View K Side View K Top View 23 PT1785P E i LL A Side View b Top View Compatibility Modes H Frequency V Frequency Resolution KHz Hz IBM VGA 31 47 eaae maa wm ao VEMXGA
11. er setting then set at Lock by pushing the UP or Down button d When the UP or Down button is released the previous setting will be saved and exit the Lock Unlock menu automatically 7 To Unlock the OSD Power menu buttons please follow the instructions below Please note the monitor has to be turned ON with a valid signal pre set a Press and hold the Menu key then press the Power key simultaneously the Lock Unlock menu will appear for 3 seconds b Use the Enter key to select OSD or Power setting then set at Unlock by pushing the UP or Down button 18 c When the UP or Down button is released the previous setting will be saved and exit the Lock Unlock menu automatically Please note a When the OSD Lock function is selected this indicates that all the buttons except power button are now disabled b When the Power Lock function is selected this indicates that the power key is disabled user can not to turn off the monitor by Power key ag On Screen Display Menus Main OSD Menu Left Right Moving screen image horizontal position to left or right Up Down Moving screen image vertical position to up or down The screen image horizontal dot clock adjustment OSD menu language selection English French OSD Language Japanese Deutsch Spanish Italian Traditional Chinese and Simplified Chinese Factory Reset Factory default value resto
12. go System and Security m User Accounts and Family Safety new your computers status 2 d Add of remove user accounts Back up your computer la 4 Set up parental controls for amy user Find andi fn probiemt Appearance and Personalization Network and Internet Change the theme View network status and tack Change desktop background Choose hornsganupeansLshttpng options Adpurt screen resolution Hardware and Sound Clock Language and Region View devices and printers bU Change keyboards or other input methods Aki a dada Hardware and Sound Add pr reme printers t T sr rlu 5 Soe palem sounds plav CDs automatically conserve Uninstall a program power update device driver and more Change display language Ease of Access Let Windows suggest settings Optirruze visual display Devices and Printers Addadence Addaprinter Mouse 8 Device Manager Play CDs of other media automatically Adjust aitem volume Changesyitem sounds Manage audio devices Power Options Change power saving settings Change what the power buttons do Require a password when the computer wakes Change when the computer sleeps Choose a power ple Display Make text and other items larger or smaller Adjust screen resolubon Connect to an external display How to comect monitor flicker refresh rate Pen and Touch Change tablet pen ee saris for sr s rag zation Turn flicks on and off Set flicks to pe lise Tablet PC Settings
13. howtobuy Technical Support Visit Planar at http www planar com support for product registration operations manuals touch screen drivers warranty information and access to Planar s Technical Library for online troubleshooting To speak with Planar Customer Support please have you model and serial number available and dial Planar Support Tel 1 866 PLANAR1 866 752 6271 or 1 503 748 5799 outside the US Hours 24 hours a day days a week Toll or long distance charges may apply Planar Systems Inc Customer Service 24x7 Online Technical Support http www planar com support 1195 NW Compton Drive Beaverton OR 97006 1992 Tel 1 866 PLANAR1 866 752 6271 or 1 503 748 5799 outside the United States Hours 24 hours a day days a week 2011 Planar Systems Inc 3 11 Planar is a registered trademark of Planar Systems Inc Other brands and names are the property of their respective owners Technical information in this document is subject to change without notice 020 0698 00 Rev G 820470025104
14. n all cables under the cover lip as seen in the step 5 diagram 6 Using a Philips Head screwdriver insert the screw CBM M3x6 into the cable cover and monitor as seen in the step 6 diagram 7 Re attach the stand back cover to the LCD stand by pressing firmly until the tabs snap into place as seen in the step 7 diagram You may also keep the cables in order by using the cable organizer 11 Connecting the Display Figure 12 1 To setup this display please refer to the following figure and procedures 1 Be sure all equipment is turned off 2 Connect the AC power cord to the power connector on the monitor and the other end into an electrical outlet 12 1 3 Connect the D SUB cable from the display s VGA input connector to the D SUB connector of your host computer and tighten the screws 12 1 4 Connect the Audio In cable from the audio input port of your display to the Audio out port of your computer 12 1 9 Connect the RS 232 or USB cable from the RS 232 or USB port of your display to the RS 232 port or USB port 12 1 of your computer 6 Configure the touch screen Refer to the Touch Screen Driver Installation section on page 25 7 Once the touch screen is configured the monitor is ready for use AN Notice To ensure the LCD display works well with your computer please configure the display mode of your graphics card to make it less than or equal to 1280 x 1024 resolution and make sure the timing of the
15. ns found in the zipped file on the CD ROM 30 If you are using a PC running Linux or Apple Mac OS follow the instructions below 1 Power on the computer 2 Make sure that the RS232 or USB cable is connected to the computer 3 Follow the step by step instructions found in the zipped file on the CD ROM When changing the Touch Interface RS 232 or USB please follow instructions below 1 Uninstall the touch driver 2 Re start the computer 3 Remove the original Touch Interface RS 232 or USB 4 Connect the computer to the Touch Interface RS 232 or USB that you would like to use 9 Load the Touch Driver CD then follow the step by step instructions as show on monitor PLEASE NOTE Don t plug in both the RS 232 and USB cables Doing so may cause a driver conflict making your touch screen inoperable 8 Product Registration and Technical Support Register Your Planar Products Today Thank you for choosing Planar To assure you receive all the benefits of your Planar product and services register your Planar product today Visit our website to register your product at http www planar com support product_registration html Cables Replacement Lamps Accessories To find cables replacement lamps and accessories for your Planar projector LCD monitor touch screen or other Planar products visit our online store at www PlanarOnline com or find other stores who carry Planar products at http www planar com
16. ntroller PT1775S SAW touch screen with dual RS 232 Serial USB controller PT1785P Projected capacitive touch screen with USB controller D Built in speakers 1W X 2 D D D D D D D D D D D D LU 5 Touch Screen for PT1700MX 5 wire resistive touch screen for finger and stylus input Surface Anti glare treatment Interface Dual RS 232 Serial USB controller Durability 35 million touches at a single point Hardness of surface 3H Typical D D D U U U Operating force 40g 200g when using a silicon rubber tipped pen with a 1 mm diameter minimum and a hardness of 60 degree Transmittance 8296x590 3 Driver Windows 7 VISTA XP 2000 ME 98 NT4 0 CE XP Embedded Linux Apple Mac OS LU Touch Screen for PT1701MX Capacitive touch screen for finger input Surface Anti glare treatment Interface Dual RS 232 Serial USB controller Durability 225 million touches at a single point Hardness of surface Mohs Hardness rating of 7 Transmittance 85 5 Driver Windows 7 VISTA XP 2000 ME 98 NT4 0 CE XP Embedded Linux Apple Mac OS D U U U U U U Touch Screen for PT1775S Surface Acoustic Wave SAW touch screen for finger and stylus input Surface Anti glare treatment Interface Dual RS 232 Serial USB controller Durability 50 million touches at a single point Hardness of surface Mohs Hardness rating of 7 Operating force Typically less than 85 g Transmittance 92 5 Driver Windows 7 V
17. red RGB Color temperature selection 9300K 6500K 5500K 7500K User Audio volume adjustment Audio On Off control 120 Appendix Troubleshooting If you are experiencing trouble with the LCD display refer to the following If the problem persists please contact your local dealer or our service center Problem No image appears on screen gt Check that all the I O and power connectors are correctly and well connected as described in the Installation section gt Make sure the pins of the connectors are not crooked or broken Problem Partial Image or incorrectly displayed image gt Check to see if the resolution of your computer is higher than that of the LCD display gt Reconfigure the resolution of your computer to make it less than or equal to 1280 x 1024 Problem Image has vertical flickering line bars gt Use Fine to make an adjustment gt Check and reconfigure the display mode of the vertical refresh rate of your graphic card to make it compatible with the LCD display Problem Image is unstable and flickering gt Use Horizontal size to make an adjustment Problem Image is scrolling gt Check and make sure the VGA signal cable or adapter is securely connected gt Check and reconfigure the display mode of the vertical refresh rate of your graphics card to make it compatible with the LCD display Problem Vague image characters and graphics gt Use Fine to make an adjustm
Download Pdf Manuals
Related Search