USER MANUAL . Radio Frequency Remote Control
Contents
1. 11 6 Targeting Lamps 12 7 Setup 13 8 Technical Data 16 9 Troubleshooting 17 10 Appendix 18 Appendix 1 Color Index 18 Appendix 2 Customizable Programs 19 Appendix 3 Color Chaser for Random Modes 20 Appendix 4 DMX table for Effect Mode 21 Appendix 5 Firmware Updating Process 22 11 Disposal 24 3 2 Safety Before you operate the unit read this manual carefully2. Make sure to keep the manual in case you need to consult this manual again or you give the unit to another person Always make sure to include this manual if you hand out the unit to anoth er person Do not operate the unit in areas where the usage of radio frequency or mobile phones is prohibited like for example in airplanes or when it may cause interference or danger Only qualified personnel may repair this product Don t open the case This device conforms to CE or FCC regulations see type label It radiates in the 868 MHz or 915 Mhz bands Always make sure that your national regulations allow the use of this de vice Only insert Alkaline batteries rechargeable batteries do not have enough voltage to power the ARC2 remote control Keep batteries away from children In case of a choking hazard go to the doctor immediately Make sure contacts are clean before you insert batteries Watch the polarity Don t try to recharge batteries MAKE SURE TO FULLY CHARGE ALL BATTERY POWERED ASTERA LAMPS WHEN STORING THEM PARTIALLY CHARGED BATTERIES WILL LOOSE CAPACITY 4 3 Getting Started a Overview Antenna Display user colors Navigate through menu adjust values LCD display back one level Save Send values in top level adjust bpm Adjust fade time Adjust brightness Adjust speed Choose program Choose user colors Switch LEDs on off Update all devices in selected groups with current setti
3. The Radio Pin makes it possible for different customers to operate their lamps at the same place without influencing other lamps To set a Radio Pin with the ARC2 go to Setup gt Radio Pin gt SET PIN and select any 4 digit pin To send this Radio Pin to a selection of lamps hold the button of these lamps pressed until it starts blinking blue rapidly blue mode then choose PAIR WITH LAMPS The lamps should stop blinking blue which indicates that they have received the new pin Factory Reset Selecting THIS REMOTE will reset all settings including keylocks and all MEMORY programs but excluding the Radio Pin Resetting LAMPS will ask you to tap indi vidual lamps to select which of the lamps in range you want to reset For event rental companies a factory reset of the ARC2 remote should be done after each rental job to avoid misleading settings from customers 16 8 Technical Data Environment Temperature operation 5 C 40 C Temperature transport 25 C 55 C 70 C for 24h Relative Humidity 0 95 Altitude up to 2000m above sea level Site interior Battery 2x 1 5V AA LR6 Measurements Unit Size in mm L183mm x W62mm x H31mm Unit Size in inch L7 2 x W2 4 x H1 2 Unit Weight in gram 160g Unit Weight in pound 0 35lb Radio Frequency RF Coverage Range 50m up to 300m Frequency EU amp EFTA 868 000 MHz 869 750 MHz Frequency US Canada Australia New Zealan
4. timeline parameters 00 at each step all colors change 01 colors change one by one 10 one step colored next step black 11 three steps colors one step black 3 2 color override mode 00 colors not overridden 01 C1 is always black 10 C1 is always C1 11 C1 and C3 are always C1 1 color wheel effect 0 color table 0 color table 1 user colors 50 color wheel effect color table is used 21 Appendix 4 DMX table for Effect Mode Channel EFFECT MODE FIX EFFECT MODE RGB 1 INTENSITY 2 STROBE 3 PROGRAM 4 SPEED 5 FADE 6 DIRECTION 0 63 FFW LOOP 64 127 FFW 128 190 REW 191 255 REW LOOP 7 SIZE defines the virtual size of the program in groups For example if SIZE is set to 2 groups only half of the program is shown on the unit 0 63 1 group 64 127 2 groups 128 191 3 groups 192 255 4 groups 8 OFFSET if SIZE is set to gt 1 group the units pixels can be shifted within the virtually larger program Increasing the OFFSET parameter scrolls the position of the unit within the virtual large program 9 RESTART PROGRAM if value is changed the program starts again from the beginning useful if DIRECTION is not set to loop 10 INDEX COLOR 1 COL 1 RED 11 INDEX COLOR 2 COL 1 GREEN 12 INDEX COLOR 3 COL 1 BLUE 13 INDEX COLOR 4 COL 2 RED 14 COL 2 GREEN 15 COL 2 BLUE 16 COL 3 RED 17 COL 3 GREEN 18 COL 3 BLUE 18 COL 4 RED 20 COL 4 GREEN 21 CO
5. USER MANUAL Radio Frequency Remote Control ARC2 Manual Version 3 4 21 Release Date May 30th 2012 Astera LED Technology GmbH Address Nahestrasse 68 70 55593 R desheim an der Nahe Germany Tel 49 0 6536 355361 Email sales astera led com 2 1 Table of Contents 1 Table of Contents 2 2 Safety 3 3 Getting Started 4 a Overview 4 b LCD Display 4 c Introduction 5 d Navigation 5 e Power Button 5 f Micro SD card 6 g B
6. in this tab the white buttons can be pressed to quickly change values of colors effects fade speed and brightness To reach the direct control tab simply press the home button b Programed Effects There are 20 customizable effects that can be selected when in the direct control tab These effects use up to 4 colors to display static or moving structures These structures are formed out of several pixels and can stretch over several lamps as well A list of the 20 programs can be found in Appendix 2 To change a programmed effect press the Prog button and use the and buttons to choose an effect This only works while in the direct control tab Note It is also possible to let the random chaser choose colors for the programs To use this feature see Chapter Appendix 10 3 Every time the Programs setting is changed random col or chaser will be switched off Note programs are best displayed on a multi pixel lightsource e g the AL6 series or stretched over a group of lamps If used with a one pixel lightsource e g AL3 M only one color will be shown at a time c Colors You can customize the pre defined programs with up to 4 colors C1 C4 All predefined programs except RAINBOW take the displayed colors from a four color palette This palette can be defined by selecting the colors C1 C2 C3 and C4 and is shown at the top of the remote control when editing the colors For example if PROGRAM is set to SIMPLE RUNNING bac
7. local dealer for that Create a Chain Chained lamps or sets will stretch their effects and programs over several lamps For example the FLAG RUNNING program can send a pixel running one AL6 until it reach es its edge then continue on the next AL6 To allow a smooth running along the correct positions have to be assigned to each lamp DMX Setup Some Astera lamps do not have a LCD display so the ARC2 can be used to set them up for DMX usage Also Astera lamps with LCD display might be easier configured re motely for DMX because their display cannot be reached For additional information refer to the DMX table in Appendix 4 DMX Address Sets the DMX address DMX Pixels Most Astera fixtures can be defined as 1 pixel or several pixels All pixels Every pixel can be controlled individually by DMX Reduced Pixels Pixels are combined to achieve a fewer pixel count for easier control Please refer to the manual of the specific device to see how many pixels will be present on DMX when this setting is chosen One Pixel The device can be controlled with only three DMX chan nels All pixels are combined into one DMX Tab Several different DMX tables can be chosen RGB S RGB S For each pixel there are three channels RGB and one channel stroboscope RGB RGB S S All RGB channels are followed by all stroboscope channels Effect Mode Fix The 4 user colors are controlled by one channel per color generates bas
8. L 4 BLUE 22 Appendix 5 Firmware Updating Process Introduction The ARC2 remote control can be used to update the firmware of most Astera lamps that are equipped with a RF receiver Antenna and can also update other ARC2 remotes Preparation Download the FRM file of the new firmware from www astera led com downloads Copy it onto a micro SD card also known as Trans Flash card that is formatted with FAT16 or FAT32 most branded micro SD cards will have this There might be different hardware releases of the same lamp If the file is not suited the lamp will not accept it Slide the micro SD card into the ARC2 Arrange the lamps you want to update and the ARC2 to a distance of 0 5 5m 2 15ft Make sure that no disturbances between the antennas can occur during update If the transmis sion is interfered lamps might get stuck during update If this happens they are unusable un til the update is completed This can be done in two ways 1 Do the same update again with the ARC2 not cycling power of the stuck lamps They will pick up again at the position they lost the transmission before 2 Power off the lamps and start the whole update again 23 Update Process 1 Power on the ARC2 and make sure the SD Card is inserted 2 Choose SETUP gt SD card gt Firmware Update 3 Choose suitable file with and keys then press Enter 4 The LCD will show POWER ON LAMPS While this is sho
9. ackground in opposite directions C1 C2 TWO COL RUNNING Same as DOUBLE RUNNING but the two pixels are of different color C1 C2 C3 FLAG RUNNING A flag consisting of three color stripes is running over the background C1 C2 C3 C4 DOUBLE FLAG RUNNING Similar to FLAG RUNNING but two flags are running in opposite directions C1 C2 C3 SPIRAL 4 COLORS The color of all pixels is changing pixel by pixel from one color to the next If the geometry of the unit allows it the direction is circular C1 C2 C3 C4 SPIRAL 2 COLORS Same as SPIRAL 4 COLORS but the movement starts at both and in opposite directions and moves back after all pixels are changed C1 C2 RAINBOW A moving rainbow is shown on the units none FIRE A flickering fire like effect is displayed C1 is the background color randomly pixels flash and flicker with C2 C1 C2 ROTOR The rotor programs are much like the FADE programs but if the units are of tower like shape then a clockwise running rotor can be seen C1 C2 C3 C4 ROTOR SPLIT 2 Same as ROTOR but two rotors in opposite directions are running C1 C2 C3 C4 ROTOR SPLIT 4 Same as ROTOR but four rotors in opposite directions are running C1 C2 C3 C4 20 Appendix 3 Color Chaser for Random Modes RANDOM MODE 7 0 7 6 strobe override mode 00 strobe not overridden 01 strobe disabled for C2 C4 10 strobe disabled for C2 C3 11 stribe disabled for C1 5 4
10. ate between them and Enter offers deeper editing of the MEMORY programs and the setup From any point in the navigation the home button can be pressed to return to the top level of the navigation This is especially useful when an inexperienced user gets lost in advanced settings and is afraid he will alter important settings e Power Button Power Mode LIGHT ON Returns from BLACKOUT to normal operation Power Mode BLACKOUT Switches all targeted lamps off and keeps them in standby causing only minimal battery drainage In blackout mode fixtures can be stored several months 6 f Micro SD card For special functions like saving programs and firmware update a micro SD card can be inserted into the ARC2 For detailed instructions about how to do a factory reset refer to Appendix 5 g Batteries In many countries the ARC2 ships without batteries due to safety regulations If this is the case for you please buy 2 Alkaline AA batteries and insert them in the correct positioning with and posi tioned correctly Do not use rechargeable batteries as they do not work stable When closing the battery compartment push each corner until the compartment cover sits in the right position Then close the slider to fix the battery compartment in a closed position 7 4 Direct Control Tab a Direct Control To change the displayed colors and effects the ARC2 offers a straightforward interface called direct control tab While
11. atteries 6 4 Direct Control Tab 7 a Direct Control 7 b Programed Effects 7 c Colors 7 d Adjustments 8 5 Preset Programs MEMORY 1 4 9 a Editor 9 b Advanced Adjustments 10 c Saving Customized Programs 10 d Additional Editing and Saving Functions 10 e Tap sync
12. c twice Tap sync does not affect all types of programs Only if they use a random color chaser tap sync has an effect 12 6 Targeting Lamps A special button has been assigned to targeting only a selection of lamps that are within the reach of the remote control Once one of the Target lamps options has been selected by choosing ENTER BACK or the HOME button you will only target those selected lamps until another value in Target Lamps is chosen Target lamps by GROUPS Each lamp can be set to belong to one of four groups G1 G2 G3 or G4 Then each groups can be controlled individually or groups can be linked together If groups are linked the program pattern stretches over them New lamps or reset lamps are set to group 1 Only sequential groups can be linked for example G1 G2 It is not possible to link G1 G3 The GROUP setting can be altered and assigned to lamps in SETUP using the REMOTE SETUP menu by SET Lamps can be assigned to one of 256 possible set addresses Each set can have up to 32 individual positions and each position can have an unlimited amount of lamps assigned to them Each of these sets can be controlled individually so you can also create a set out of just 1 lamp if you want to be able to target this lamp individually Sets can easily be created by using SETUP gt CREATE A SET by TAPPING THEM By using this setting lamps will not receive any information unless they are tapped Tappe
13. d 902MHz 928 MHz WARNING The user must make sure that the national regulations allow the operation of this RF device If this is ignored serious harm may occur 17 9 Troubleshooting Faulty condition Cause Troubleshooting Units are out of sync Adjustment of the SPEED parameter can cause deviation between the units also the units will drift out of sync after a few hours Press SEND button or change PROGRAM Units behave incorrectly Due to the vast number of settings one cannot always predict behavior of the units if setup was already done earlier Do FACTORY RESET on units and or remote control One a few units don t play the correct program even if it was set up earlier If a unit is powered up after the light scene was setup with the remote control if will not work correctly Press SEND button on remote control to update the unit A unit is flashing in blue or other color all the time and not accepting any command It might be in BLUE MODE Hold down the button until the flashing stops One a few units don t react on the remote control You might be targeting the wrong lamps Check TARGET LAMPS and select the set you have programmed the lamps in or make sure you are sending to all 4 groups to target all lamps Units will go out of battery after only 6 hours of operation Some units last only 8 hours with COLD WHITE if the LED POWER is set to NORMAL For HIGH BRIGHTNESS th
14. d means that their button is pressed after they indicate that new information is available Usually they do this by a short white flash every 1 2 seconds by TYPE If lamps of different types are used they can be controlled by type For example if you have AL6 and AL3 S setup they can be controlled individually by choosing their type by SERIAL NUMBER If the serial number of a lamp is known it can be addressed directly by entering the S N into the remote control 13 7 Setup The setup offers advanced settings that can be done before or after an event like factory reset form ing groups of lamps calibrating colors and setting a partial keylock when giving away the ARC2 To enter the SETUP menu while in the top level of the navigation press the minus button until you see SETUP then confirm with Enter If you are not sure in which level you are press the home button to get to the top level If SETUP does not appear on pressing the button check the KEYLOCK setting Chapter 5 d Create a Set Sets combine several lamps which can be addressed at the same time and arranged in a preferred order to stretch effects over them Unlike groups a huge number of sets 256 can be programmed and targeted with the Target Lamps button A set can also be applied to only 1 lamp if this lamp needs to be targeted quickly There are several separate manuals and video manuals available to explain you how to create a set Ask your
15. dition to the 3 pre programmed tabs MEMORY 1 3 the MEMORY 4 tab provides room for 8 own creations that can be launched with the white buttons when inside this set MEMORY 1 decorative This set is suited for basic events presentations background lighting and a general decorative mood Also this is the set where the home button leads to MEMORY 2 party slow This set has pre programed color transitions for dinner parties early hours of disco nights etc MEMORY 3 party heavy This set has fast and strong color effects strobe effects and rapid changes between colors It is suited for dancing events and to hightlight special parts of a show MEMORY 4 user define This set is not pre programed by Astera Chapter 5 a will discuss how its 8 keys can be programmed with customized colors and effects It can be used by event preparing companies to prepare special programs for their customers for quickly launching them during events a Editor The Editor is an advanced function that lets you customize the 3 sets of preset MEMORY programs decorative party slow party heavy In addition you can save your own programs onto MEMORY 4 user define if you want to keep the original programs in MEMORY 1 3 The Editor works similar to the direct control tab and while in the Editor you can use the white buttons to change their values C1 C4 Fade Speed Brightness Prog Have a look at chapter 4 b d if you don t know how to use these funct
16. e runtime may be shorter than 8 hours Adjust LED POWER and or see manual of the unit The display of a unit is showing BLACKOUT and there is no light output Either the unit is set to BLACKOUT mode or DMX FAILURE AC FAILURE is set to BLACKOUT and one of these conditions persists Press I O on remote control and set to DISABLED Check settings of DMX FAILURE AC FAILURE Maybe do FACTORY RESET Each time I press the tap sync buttons the displayed colors are changing You have switched Random Colors on Enter the Editor select USE RANDOM COLS then select NO 18 10 Appendix Appendix 1 Color Index 19 Appendix 2 Customizable Programs Name Light Effect Used colors ONE COLOR STATIC All pixels show the same color C1 TWO COLOR STATIC Same as ONE COLOR STATIC but not all pixels show the same color they are divided into 2 3 or 4 parts C1 C2 THREE COLOR STATIC C1 C2 C3 FOUR COLOR STATIC C1 C2 C3 C4 ONE COLOR FADE All pixels show the same color but the color changes between all four USER COLORS C1 C2 C3 C4 TWO COLOR FADE Same as ONE COLOR FADE but not all pixels show the same color they are divided into 2 3 or 4 parts C1 C2 C3 C4 THREE COLOR FADE C1 C2 C3 C4 FOUR COLOR FADE C1 C2 C3 C4 SIMPLE RUNNING All pixels have C1 color except one that is running over them with C2 C1 C2 DOUBLE RUNNING Same as SIMPLE RUNNING but two pixels are running over the b
17. econds can be set This time reflects the duration of the selected program Note With the change of speed you might get the units out of sync In order to re sync press the Send key or change the program Chapter 4 b Brightness You can select the Brightness Intensity or the Power Scheme of the lamp Both are strongly affecting the battery runtime of the lamps Choose INTENSITY to change the brightness of the LEDs between 0 and 100 in intervals of 10 Choose Power Scheme to adjust the overall power scheme of the lamp between HIGH BRIGHTNESS NORMAL and MAXIMISE RUNTIME When choosing high brightness the LEDs are about 30 brighter but the battery will drain faster In maximise runtime the LEDs are less bright but the fixture can be used well over 10 hours Attention Battery runtime of all the Astera lamps is stated for the Normal power scheme Altering the power scheme will lead to different battery runtime Note New Astera fixtures and ARC2s are set to HIGH BRIGHTNESS Also after a factory reset they will switch back to HIGH BRIGHTNESS 9 5 Preset Programs MEMORY 1 4 For quickly changing the mood of a lamp or setup of lamps the 24 pre programed MEMORY programs can be quickly launched and optionally be customized see Chapter 5 a c To start a MEMORY program choose one of the pre programmed MEMORY tabs and click one of the 8 white buttons To reach the memory tabs press the home button and press the button In ad
18. ic colors Effect Mode RGB The 4 user colors are controlled by three DMX channels each 14 Strobe Single One DMX channel is supplied for the control of the strobe function all pixels will strobe identical When using this setting DMX TAB should not be set to RGB S RGB S Multiple For each pixel the stroboscope can be controlled indi vidually Off Stroboscope is turned off globally DMX Failure Sets the behavior of the light in case of an interrupted DMX signal Hold Output remains unchanged the last received DMX frame is displayed Emergency Light If the DMX reception times out the light turns white Blackout If the DMX reception times out all light turns black Remote Setup Usually all configuration settings like changing the DMX address chain con figuration and so on is done directly on the units This might not be feasible if several units with the same settings have to be configured with the same set tings or a unit is not equipped with a LCD display Remote Group Assigns lamps or sets into any of the 4 groups If not programmed all lamps are set to group 1 Input Select If a lamp has several input signals for example it is connected to a DMX cable but should be targeted by the ARC2 the preferred input signal can be defined XLR DMX for the signal of wired DMX Wireless DMX for the signal of wireless DMX Remote Control for the radio signal of the ARC2 Standalone to keep the
19. ions To enter the editor choose any of the 4 MEMORY sets press and hold one of the 8 white buttons for 2 seconds Alternatively go to a MEMORY tab choose any of the white buttons and press enter to edit the button s memory 10 b Advanced Adjustments If adjusting colors Program effect Speed Fade and Brightness are not enough a range of advanced adjustments can be changed in the Editor To change additional adjustments of colors and programs enter the Editor then press the plus and minus buttons choose the setting you want to change and confirm with Enter Stobe Speed Adjust frequency and confirm with Enter Program Direction Choose between forward left to right backward right to left and if you want to run the effect only once or repeat it in a loop Program Parameter Changes parameters depending on the program currently running Blower Speed Changes the power of the blower Use Random Colors When switched to YES it starts the random color chaser which places ran dom colors on the 4 user color channels C1 C4 Each time tap sync is pressed the 4 user colors will change Random Mode Features a range of different chaser modes Overview in Appendix 3 Random Fade Fading time of the random chaser c Saving Customized Programs At the end of setting Colors Programs Adjustments and Advanced Adjustments your ARC2 can save the chosen setting to one of the 8 white keys To save settings selec
20. kground color will be C1 and the color of the running pixel will be C2 There are 3 kinds of colors available for that Standard Colors red orange yellow green cyan blue magenta pink white warm color warm black can be quickly chosen Index Colors 256 standard index colors can be chosen when selecting INDEX COLORS The colors are listed in Appendix B User Colors If this is not enough choose USER COLORS Here you can mix colors out of the 3 color channels red blue green 8 To change colors click any of the C1 C4 buttons to change their color This only works while in the direct control tab Note Not all programs use all 4 colors C1 C4 For example the program called TWO COLOR STATIC uses only 2 colors so half of the pixels will be in C1 and the other half in C2 d Adjustments The programs you have chosen can be further adjusted in fade speed and brightness Simply click fade speed or the brightness button and use the and button to change their values This only works while in the direct control tab Fade Sets fading transitions between steps of the program in amount of the step time If set to 0 there will be no fading at all the color will be switched at once If set to 100 the color change will go smoothly from one to the other color Any value in between will be a mix of these two settings Speed Changes the speed of the program A time between 0 09 seconds and 9 minutes and 21 s
21. last input signal for example 1 color until another input source is chosen Auto Automatically chooses an input source AC Failure Emergency Light If no AC signal is detected the light turns white No Action Blackout If no AC signal all light turns black Manual White Calibration You can enable automatic white calibration or manually adjust the red green and blue levels that are used to display white color SD Card Backup Keys Saves the colors and effects that have been as signed to the white keys Choose a name with the plus minus amp Enter but tons Back Tap sync jumps to the next set of letters deletes gt gt stores the keys with the chosen name Restore Keys Copies the stored keys to the ARC2 s memory Firmware update The ARC2 can be used to update the firmware of most Astera lamps and controllers that are equipped with a RF receiver Antenna Please refer to the Firmware update manual in appendix 10 5 for detailed instructions 15 Test Radio The Test pattern Color Change allows you to test the radio frequency range conveniently by walking away from a lamp just 8 16m while holding the ARC2 If the Test Radio is activated the remote switches to minimum output power and transmits a color change change every second If the color change works in that range lamps and remote are ok You might need to move the remote around a little to avoid interference Radio Pin
22. ngs Home button Return to top level Target a lamp by its group set etc b LCD Display Definition of symbols 1 Receiving 3 Transmitting 4 Inside Editor mode 5 Synchronization between units is active 8 Battery status 5 c Introduction Astera ARC2 radio frequency remote control is being used to control Astera s wireless lamps wireless controllers and wireless DMX transmitters The system offers several sets of predefined effects and predefined programs that can be quickly launched For advanced applications the programs can be customized over the Editor see Chapter 5 a The re playing colors can be defined to fit a theme or corporate identity These colors can be used in pro grams which can be adjusted on speed brightness and fading effects It is also possible to address group and synchronize several units and to stretch programs over sev eral lamps For example the RAINBOW effect can be stretched over two or more units displaying the full rainbow spectrum at the same time d Navigation Navigation through the system is done with the top 4 buttons of the remote control Enter confirms a value and button choose a value and Back moves up 1 level in the navigation The top level of the navigation contains direct control the 3 sets of pre defined memory programs MEMORY 1 MEMORY 3 as well as an area to store own programs MEMORY 4 and the SETUP The and buttons are used to navig
23. spose is according to your local ordinances and or regulations to avoid polluting the environment BATTERIES Don t throw empty batteries into the garbage Bring them to a collecting point for used batteries 25 This instruction manual is part of the device and persons operating the device must have access to it at any time Safety precautions mentioned in the instruction manual have to be observed If the device is being sold this instruction manual has to be included Translations If the device is being sold this instruction manual has to be translated into the national language of the destination country If discrepancies occur in the translated text the original instruction manual has to be used to solve them tor the manufac turer has to be contacted 2012 Astera LED Technology GmbH All rights reserved R desheim Germany
24. t SAVE TO KEY x while inside the Editor If you have not finished a selection press the Back button until you see Editor active d Additional Editing and Saving Functions In order to avoid accidental mistakes when saving a special selection to a particular button and over writing existing settings there are several tools to prevent misusage In the top navigation press the Enter button to Enter the Memory settings Edit Key Enter the Editor Offline Edit Enter the Editor and edit programs and adjustments offline without displaying the changes on the controlled lamps 11 Restore Key Restore settings of a particular key Clear Key Delete settings from a particular key Info Show Firmware version Hardware version and RF frequency Keylock Set a partial keylock before handing the ARC2 to a customer to prevent him from deleting important program settings You can choose to hide the SETUP menu from him or to hide SETUP and disable the function to overwrite programs e Tap sync Tap sync can be used to adjust the speed of the transitions of MEMORY 1 4 programs and programs defined by the user It can be used to synchronize the lamps speed to mu sic that is played but also to the mood of an event To tap sync while in the top level of the navigation press the tap sync button twice in the rhythm you want to synchronize the lamps If you not sure in which level you are press the home button then press tab syn
25. wn on the ARC2 press the on off button of all lamps you want to update They will not power up as usual but stay in an up date mode instead If a lamp powers up as usual either the wireless connection is bad or the FRM file does not match the lamp you are trying to update 5 When all lamps are prepared press the ENTER key on the ARC2 to start the update 6 The ARC2 s display will show a progress bar Wait until the update is completed this will take 30 60 seconds 7 If the updated worked the lamps will power up again and behave as usual If a lamp does not power up the update got stuck Then either directly start the update again on the ARC2 not touching the lamps or power off the lamps and start the whole process again If you want to find out which firmware you lamp is running take a lamp with LCD display hold MENU until you enter the menu choose INFO then FIRMWARE VERSTION Updating another ARC2 remote control Take out the batteries of the ARC2 and do everything as described above In step 4 while the sending ARC2 shows POWER ON LAMPS insert the 2 batteries into the receiving ARC2 A flashing LCD backlight indicates that the update is in progress 24 11 Disposal Follow local ordinances and or regulations for disposal PACKAGING The unit is shipped in protective packaging This packaging can be recycled UNIT Don t throw the unit into the garbage at the end of its lifetime Make sure to di
Download Pdf Manuals
Related Search