High Definition Terrestrial Receiver User`s Manual
Contents
1. 32 Warning The USB interface is for software upgrade of the Receiver only using a USB Flash Drive with FAT32 file system format The USB interface could not support the USB Flash drive that with U3 PRO System Never connect a portable hard disk to the USB interface of the Receiver 8 2 UPDATE THE RECEIVER BY USB INTERFACE 1 Plug USB drive that with the update file to the USB interface of the receiver on the rear panel 2 Power off the receiver by press STANDBY key on the remote control or on the front panel of the receiver Then press STANDBY key again to power on the receiver and the USB upgrade process should be launch automatically The receiver would read the upgrade file and upgrade the receiver in approximately 3 minutes The receiver would restart automatically after upgraded NOTE Please do not remove the USB drive from the receiver and power off the receiver during upgrading process Otherwise the receiver may not work properly Please don t power off the set top box Reading updated file completed y Updateing uboot completed kernel completed Ey Updateing rootfs 33 9 SPECIFICATION Tuner Input Connector IEC 16902 Female Input Frequency Range VHF amp UHF Num of RF Inputs Input impedance Input Level RF output Connector Loop through Demodulation Standard Guard interval Modes FEC Modes Rate Carriers Constellation Demodulation Network Channel bandwidth System Resources2. Microprocessor SDRAM memory FLASH memory Display Planes Graphic resolution Video Decoder Standard Transport stream Video decoding Video resolution Aspect ratio Audio Decoder Standard Audio decoding Dolby Digital AC 3 Sample rate 1 75 ohm 78 dBmV 20 dBmV bypass IEC 169 2 Male 47 862 MHz ETSI EN300 744 1 32 1 16 1 8 Active Symbol duration 1 2 2 3 3 4 5 6 7 8 All modes supported including non hierarchical COFDM QPSK QAM16 QAM64 2K and 8K MFN SFN 7 and 8 MHz wide channel 21 68PLL CSM1200 128 DDR2 SDRAM 2x64MB 8 NOR FLASH 7 SEGMENTS LED RGB565 ARGB444 CLUT8 and CLUT4 ISO IEC 13818 2 and ISO IEC 14496 10 ISO IEC 13818 1 MPEG 2 SD HD MP ML and MP HL Profile Level 3 and High Profile Level 4 480P 5761 576P 720P 10801 1080P Option 4 3 16 9 AUTO MPEG 4 H 264 AVC SD HD Main ISO IEC13818 3 1011154 MPEG 1 and MPEG 2 Layer I amp II Dolby Digital Audio Stereo down mixing to analog and digital audio outputs including HDMI For digital outputs L PCM stereo encoding is provided 32 kHz 22 1 kHz 44 1KHz 48 kHz Subtitles amp Teletext Subtitle Teletext DVB Subtitle EBU TELETEXT 34 Rear Panel CVBS outputs Audio CINCH Y C Optical S PDIF Coaxial S PDIF YPbPr outputs HDMI USB SCART Front Panel bi colored LED 7 segments LED Keys Accessories Remote control unit Batteries User Manuel L R Cinch cable RCA cable Power AC input
3. the menu by press LEFT RIGHT key on the remote control 29 Time Settings 1x 7 4 PIN SETTING Highlight the PIN Setting item by press UP DOWN key and enter to the PIN setting sub menu by press OK key Default value is 0000 System Setting 1 scari Inter tact Factor Reset The PIN Setting sub menu allow the user to enable disable the pin code modify the pin code and set the parental rating for lock some channel that no suitable for the children Highlight the item by press UP DOWN key and set the preferred parameters by press LEFT RIGHT key Press MENU key or EXIT key back to the previous menu with save settings PIN Settings Parent Rati K 0 l onfirm PIN D 0 9 number ki to inputi ess key to confirm 30 7 5 SCART INTERFACE Press MENU key on the remote control and move the cursor by press UP DOWN key When the Scart Interface is highlight press OK to enter to the Scart Interface menu The Video Output was including CVBS and RGB Press LEFT RIGHT key on the remote control selection Video Output type Scart Interface 1x 7 6 FACTORY RESET This function allows the user to return the Receiver to factory default settings From the System setting sub menu highlight Factory reset with the UP DOWN buttons and enter the system PIN code and the reset process will start automatically The default PI N code is 0000 Please note that after resetting the Receiver all previously stored
4. 30 ROW Saw nimi e TTE 31 05 IFACTOP Y mE 31 Z PRODUCT INEO utc Et tuu 31 OMEN T 32 UPDATE THE RECEIVER BY USB2 0 INTERFAQGE eee Hmmm 32 8 1 COPY HE UPDATE FILE TO THE USB DRIVE FROM PC 32 8 2 UPDATE THE RECEIVER BY USB INTERFACE a 33 SPEGIEICATION ti us tM M E DM ta A MM 34 IMPORTANT SAFETY INSTRUCTIONS TOREDUCE THE R SK CAUTION ELECTRIC SHOCK DO NOT REMOVE COVER RISK OF ELECTRIC NO USER SERVICEABLE SHOCK DO NOT PARTS INSIDE RE ER OPEN SERVICING TO QUALIFIED SERVICE PERSONNEL This symbol indicates This symbol indicates dangerous voltage important instructions inside the produc that accompanying the presents a risk of electric product shock or personal injury Dolby and the double D symbol are trademarks of Dolby Laboratories Manufactured under license from Dolby Laboratories 1 INTRODUCTION This user s manual is intended to describe the procedures for operating the HDT8340 FTA CS12 High Definition Digital Terrestrial Receiver This product is a high performance Digital TV Terrestrial Receiver It offers users with all free to air DVB T Digital TV programs being broadcasted in Russian 2 MAIN FUNCTION AND FEATURES This product is a high performance and cost effective HDTV Terrestrial receiver It fully complies with DMB T receive
5. TV channels will be lost The Receiver may take approximately 30 seconds to finish the factory reset process System Setting 3 scart intertact 7 7 PRODUCT INFO Press MENU key on the remote control and move the cursor by press UP DOWN key When the Product Info is highlight press OK to enter to the Product Info menu Press MENU key back to the previous menu or Press EXIT key EXIT and save setting 31 Product Info 13 Model No icity Product Uu l u1 Hardware Versions 7 4050 software Yersionrz v1 00 Release Date PULES 7 8 CA SERVICE Press MENU key on the remote control and move the cursor by press UP DOWN key When the CA Service is highlight press OK to enter to the CA Service menu The sub menu was including Pin Setting Parent Lock Smartcard Info Subscription Token Status and Event Status Smartcard Infe Sulsse prt ion i loken Status nt Statu 8 UPDATE THE RECEIVER BY USB2 0 INTERFACE 8 1 COPY THE UPDATE FILE TO THE USB DRIVE FROM PC 1 Please go to service website or contact our customer service to get the latest software for updating the Receiver 2 Plug the USB drive to the PC and backup the entire data of the USB drive Right click the USB drive and select Format item Format the USB drive as FAT32 file system 3 Copy the update file that name as update ud to the root of the USB drive Then remove the USB drive from the PC
6. and new batteries ifthe remote control unit is not going to be used for a long time remove the batteries Caution Keep batteries out cf children s reach If batteries are swallowed contact a physician Immediately 4 FRONT AND REAR PANEL 4 1 REAR PANEL YPbPr A C A LE COAX 1 J QOOC La LJ Cy el OQ ANT IN LOOP OUT m VIDEO L AUDIO R ANT IN LOOP USB HDMI VIDEO L AUDIO R S VIDEO OPTICAL TV VCR SCART DC 12V S4 IDEO OPTICAL Rear Panel NN Audio and video 4 2 PANEL The LED is power indicator the green LED is signal indication User can access those function keys as follow CH UP CH DOWN VOL LEFT and VOL RIGHT 5 INSTALLATION Note Digital TV Antenna is used to connect to the Terrestrial Receiver The Antenna should be used where the user is within an area with Digital Terrestrial TV coverage but the premises in which the user intends to use the Receiver has not yet been upgraded with Digital Terrestrial TV receiving capability Please refer to Installation for details f you do not know whether the building concerned has been upgraded with Digital Terrestrial TV receiving capability you may make relevant enquiries with your building management Please connect the Receiver to your television set HDMI cable recommended and that the antenna is connected to the ANT IN input c
7. entire files on the extend hard disk might be display on the right of the screen Move the cursor to the prefer file by press LEFT key Delete the highlight file by press RED key and back to the previous root by press BLUE key q QUAM LQSNULAAMwgnanbiok1qaPfonRgIQmSSEIEUEAA AMaARG ARM C OCAMOR ERU EA ARAM PLADOADAELPLASPDS 6 4 2 PVR FILE Move the cursor by press LEFT RIGHT key and UP DOWN key to highlight the PVR FILE item All the PVR file that on the extend hard disk might be display on the right of the screen Select the prefer PVR file by press LEFT RIGHT key and UP DOWN key then press OK to play the video Delete the highlight file by press RED key File Manager a Address 6 5 INSTALLATI ON To enter to the Installation menu press MENU key and press DOWN key to move the cursor then press OK key to confirm while the Installation item is highlight The installation menu allow the user to search the channel You have to input the pin code before you enter to the installation menu The default value is 0000 18 6 5 1 Manual Search Press LEFT RIGHT key to select Manual search mode while the installation mode item is highlight Input the prefer frequency by press 0 9 number key on the remote control Press LEFT RIGHT key to select the prefer bandwidth after you set the frequency You also could set the antenna power supply for the flat antenna if it is necessary Press OK key to start manual
8. range Power consumption Standby consumption Low Power mode idle Physical Operating Temperature Storage Temperature Size W x H x D mm Size packaging Weight 1 CVBS video output 2 Analog Audio L R connectors white red color S Video Digital Audio output Digital Audio output Analog HDTV video output Digital HDTV video output with HDCP HDMI version 1 1 or later USB2 0 Analog Audio and video output Red Green to indicate the various states of the STB To display the channel number or and other information 7 keys Standby P P V V Menu OK IR 36kHz RC3 other on request 38kHz NEC 2 X AA R6 type lin English and Chinese 340mmx250mmx60mm 400mmx310mmx80mm 1 5 kg 35
9. set aspect ratios 16 9 Stream on a 16 9 TV 4 3 Stream on a 4 3 TV Whatever the mode Whatever the mode 4 3 Stream 16 9 16 9 Stream 4 3 Letter box Letter box Pan and scan Pan and scan Full Screen Full Screen Emm Display black bars ee Nt display area of the stream 5 6 TELETEXT Press TELETEXT key to launch the TELETEXT window during you watching TV program The entire TELETEXT with different language might be display on the TELETEXT window Press UP DOWN key to select prefer language TELETEXT and press OK key to launch TELETEXT SS Lei 19 58 58 EFTATA IEE The TELETEXT home page would appear in approximately 5 seconds The screenshot is illustration below Use RED GREEN YELLOW BLUE key on the remote control as function key to browser more content Back to the TV program screen by press EXIT key TELETE 100 20 Mar 18 ELE AH ET 01 NERS 12 BUSINESS 102 SPORTS i TAB 103 WEATHER 200 LIFESTYLE M04 TELEVISION 109 2 INDEX BD CAPTIONS 33J LOTT 111 Bush marks Irag fifth anniversary 129 Anger ower sewism ruling 211 NE football loses CED 760 Dn The Gos 01 Kelly Tarlten s sale likely ix Live heal ngs unm T IN sg TL 5 7 TV CHANNEL AND RADIO CHANNEL LIST Press OK key to display the entire TV channel or radio channel when you watch TV program The screenshot is illustration below Press TV R on the remote control switch the TV ch
10. the channel name after you press RED key You might have to input the password if you want to delete a lock channel Press MENU key back to the previous menu or Press EXIT key EXIT and save TY Channels f 6 6 2 Lock Channel Press GREEN key on the remote control to lock the highlight channel or unlock the highlight channel You have to input the password if you want to lock the channel or unlock the channel Default value is 0000 One lock icon will display on the right of the channel name after you lock the channel Press exit key to exit the channel list menu and save TY Channels f 4 6 6 3 FAV Channel Add the highlight channel to the favourite s channel list by press YELLOW key on the remote control One Favourite s icon will display on the right of the channel name after you set as favourite s channel Press EXIT key on to exit the channel edit menu and save 21 TV Channels 3 6 6 3 Move Channel Press BLUE key on the remote control one moving icon will display on the right of the channel name then press UP DOWN key to move the highlight channel to prefer position and press BLUE key again to confirm or press OK key to confirm You might have to input the password when you sort the lock channel Press EXIT key to exit and save 7 SYSTEM SETTINGS Press MENU key on the remote control and move the cursor by press DOWN key When the SYSTEM SETTINGS is highlight press OK to enter
11. High Definition Terrestrial Receiver User s Manual Ol 9 Table of contents US BG Gea tk ETT PR 4 MAIN FUNC TION ANO FEATURES u uuu u un L uu u uuu UR ad andina oe se te eee s dain eet 4 TEE AREMOTEGCONTHOL 5 FRONT IAND GEAR DAL 7 T REAR ANE dons ML 7 42 Seth I Ko hk 7 Qan 8 54 Sua Tu iya ai 9 5 2 AUDIO LANGUAGE AND AUDIO MODE 10 5 9 SUBTITLE 10 RESOBUTON 11 55 11 56 TELETEXT TR 13 5 7 TV CHANNEL AND RADIO CHANNEL 13 50 FAVOURITE S uu uuu EI T 14 MENU INFORMA T O N ui uuu tar ats aceti heo m sae ote Su un Sua Gu Sam muu 15 6r MAN MENUSTRUCTUUR E r sir iS roro voc eo etos Ou au pi ase rec 15 uyu namna Sua cS E I Pro 16 bo MT cod 21S els s oul RESEND us 16 SE EN BENT EDA ne a Se gO Toe Oe 17 E L ES E en E mun a E ORI E ENCOUNTER sn cl satan PR 17 27 PVP RHONE PRX ee ee 17 6 5 u u Er scitu miS e MEL LU LM seca sect rS URDU M P EU LR IA L
12. M patas 18 eom MANUAL SEARCH RR RR ERES 19 5 52 JAUIOQEAROB u nl lun ls sumnak amu Et Su 19 E iz DIREKTE 20 DS E TE CANINE le Shae ets hated nota 21 ec at iz ua ae ncaa ie ss SA sae AEN 21 03 OS AOI Mr 21 6 03 ERE I 22 SS TENISEJTLDINOSS u Lulu uuu Puno IDA E LPS MMC he e 22 Zh AM SERITNGOSC caca unu Ed DM ML d M LE d 23 A EO TO deme mex REM 24 ASPECT TNT 24 Toss WIPEGIBESODPIONE uu u Zura om u aa dah MS as 24 Var NIDEO MODE NE ao TTE 25 Perse TP ie MER REI PN ERR 25 DIGITAL AUDIO OUTPUT ua Susupi g WI aqu dee sae xs ed eor as Rene RO E RENS 26 7 2 LANGUAGE 26 7 2 1 MENU LANGUAGE a a 27 Jee AVDO EANGUAGE Lu us uuu u u uka sak ashqa asqa sa Sa aussi aasawa 27 7 29 GUPT E ED CNN 28 fo d TEFETEXT EPANGUJAGE RIRs 28 CITPANSPAPEN0CYu Z L Z unapuy eee wass akuy a Toba asun E asa 29 TIME pi mmm 29 JPIBESSET E uuu E a usa Aut u saan toss eee ee LE
13. V SET with S video cable and composite cable the resolution of the video output must set as 5761 Otherwise you could not see any picture on the TV screen If ou set the resolution of video output as other value except 576l by mistake when you use the S video cable and composite cable connect the receiver to the TV SET You might press RES key on the remote control in every 30 seconds until you could see the picture on the TV screen You also could use the HDMI cable or YPbPr cable to connect the receiver to the TV SET then set the prefer value 5 5 ASPECT RATIO The aspect ratio of the video might be 4 3 also know as Anamorphic Image or 16 9 also know as widescreen TV Normally the aspect ratio of standard definition video should be 4 3 and the high definition of video should be 16 9 In order to have excellent picture on the TV set the user have to set the prefer aspect ratio Press the ASPECT key to display the aspect ratio setting window The screenshot of the aspect ratio window is illustration below Press the UP DOWN key to moving the cursor and press the OK key to confirm prefer aspect ratio You also could press ASPECT key on the aspect ratio control window to select prefer aspect ratio and press EXIT key to watch TV program S Ep ASPECT K k x LETTERBOX16 9 1B O0 j T TEE B x Here is a description of how the aspect ratio conversion mode chosen the received stream and the user s television
14. al subtitle information You might press SUBTITLE key to select prefer subtitle language The subtitle information window would display on the screen after you press SUBTITLE key All the subtitle languages would display on the subtitle information window The screenshot is illustration below Pressing UP DOWN key to move the cursor and press OK key to select the prefer subtitle language and exit the window ESAE EPIN 10 5 1 59 Subtitle FRA AS SAL Say Eg BH 5 4 RESOLUTION The video of program might have different resolution such as 720x576P 1280 720 1920 10801 Normally the standard definition program might have 720 576 and high definition program might have 1280 720 1920 10801 In order to have excellent picture on the TV screen the user might press RES key on the remote control to display the resolution control window The screenshot is illustration below On the remote control window you could find 4801 5761 576P 720P and 1080l Default value is 5761 Press the RES key to select prefer resolution of the video output on the remote control window and press OK or EXIT key to exit the resolution control window You also could select the prefer resolution by press UP DOWN key then press OK key to confirm gez Video Output 4801 720 576 10801 SUE AT NOTE The S Video output and the composite video output only support 5761 output When you connect the receiver to the T
15. annel or radio channel Press the UP DOWN key on the remote control to select prefer channel and get the preview picture the right of the screen Press OK key or EXIT key back to the TV program The information of the presented ware includes 1 The signal strength and the signal quality of the current channel 2 The status of the entire search as LOCK channel or favourite s channel 3 The LCN and the channel name of the entire channel 4 The preview of the highlight channel 5 8 FAVOURITE S CHANNEL You could add your interesting channel to the favourite s channel list and press FAV key on the remote control to display your favourite s channel list Press UP DOWN key on to get the preview of the channel on the right of the screen and press OK to confirm or press EXIT key to watch the TV FAV Channels 14 6 MENUINFORMATION 6 1 MAIN MENU STRUCTURE TV Channels Program List Radio Channels File Manager All files PVR files Installation Auto Search Manual Search I OCK DEI FAV MOVE AV Settings Language Setting Time Settings PIN Settings Scart Interface Factory reset Product Infor CA Service 6 2 MAIN MENU To display main menu by press MENU key on the remote control The screenshot is illustration below You could find Program List File Manager Installation Program Edit System Setting and Product Info on the main menu Press UP DOWN key to move the cursor and press OK k
16. e current next program of the channel The signal strength and signal quality of the current channel would display on the right down of the information bar You also could find some icon such as HD AC 3 and TTX on the left down of the information bar Those icons would highlight display when the corresponding information was taken on the current channel 7 TIE REL 0 51 43 1 IV Channels 901 SZIVM02 sum Jd mm bo 4 4 E 5 2 AUDIO LANGUAGE AND AUDIO MODE The program might have multilingual audio language and the audio might broadcasted on different audio mode such as Stereo Left or Right You might press Language key or AUDIO key on the handset to select prefer audio language and audio mode The Audio Track window would display on the screen after you press Language key or Audio key The screenshot is illustration below All the audio languages will displays on the audio track windows You might press UP DOWN key to moving the cursor and press OK key to select prefer audio language and exit the audio track windows You might press Left Right key to select prefer audio mode If there is nothing audio output after you select the audio language It indicates that there is no audio on the current audio mode So you have to select prefer audio mode EIS Audio Language 13 Audiol MPEG kT LAO AIRIS 5 3 SUBTITLE The program might have multilingu
17. elevision Up to 1080P video resolution supported Multi bilingual OSD language audio language and subtitle language supported USB 2 0 interface for MP3 amp JPEG playback PVR and software upgrade Record digital television FTA program to a USB Flash Drive or an external USB portable hard disk and playback via USB2 0 10 Low Power mode 3 REMOTE CONTROL Photograph Key Function MUTE Disable Audio output STB POWER Power on off the STB TVIRADIO ax 0 9 numeral buttons for input of numbers or for selecting a TV channel SWAP Recall last channel while watching digital TV or listening to radio Press TV R key to switch between TV TV R program and Radio program VOL VOL Increase or decrease the audio output volume CH CH Select next previous channel Function key in different page GREEN Function key in different page YELLOW Function key in different page BLUE Function key in different page MENU Display menu press again to exit current menu EXIT Back to previous menu without saving to Back to previous menu without saving menu without saving INFO Key to display the information bar during watch program Press EPG key to display 7 days EPG information UP DOWN ihe selection up down within menus and While watching a channel the LEFT RIGHT buttons increases or decreases the audio LEFT RIGHT output volume Within a menu press the LEFT button to return to previous menu and
18. ey to confirm the prefer item Press EXIT key back the TV program Main Menu I mManagi g in tall Program f tem Setting B Product 6 3 PROGRAMLIST You could press UP DOWN key to move the cursor and press the OK key to confirm while the Program List item is highlight on the main menu The entire TV channels or radio channels would display on the program list The screenshot is illustration below Press TV R on the remote control switch the TV channel or radio channel Press the UP DOWN key on the remote control to select prefer channel and get the preview picture the right of the screen Press OK key or EXIT key back to the TV program The information of the presented ware includes 1 The signal strength and the signal quality of the current channel 2 The status of the entire search as LOCK channel or favourite s channel 3 The LCN and the channel name of the entire channel 4 The preview of the highlight channel TY Channels 6 4 FILE MANAGER To enter the File Manager menu press the MENU button on the remote control unit then press the DOWN button twice followed by the OK button or press PVR key on the remote control to the File Manager directly File Manager menu allows the user to manages the file that were storage on the extend hard disk which connect to the receiver through USB2 0 interface 6 4 1 All file You could press UP DOWN key to highlight the All File item and the
19. menu allows the user to set the language for the user interface audio output language TELETEXT language and subtitles language Press MENU key back to the previous menu or Press EXIT key EXIT and save setting 26 Language Settings 13 7 2 1 Menu Language Highlight the Menu Language item by press UP DOWN key and set prefer menu language by press LEFT RIGHT key on the remote control Press MENU key or EXIT key back to the previous menu with save setting Language Settings 3 lransparen 7 2 2 Audio Language Highlight the Audio Language item by press UP DOWN key and preset the preferred audio language when a programme is broadcasted with several audio tracks by press LEFT RIGHT key on the remote control If the preset audio language could not find in the program the receiver might select the first audio language from the program Press MENU key or EXIT key back to the previous menu with save setting Please read the 6 2 Audio language and audio mode to get further more information 27 Language Settings 1 7 2 3 Subtitle Language Highlight the Subtitle Language item by press UP DOWN key and preset the preferred subtitle language when a programme is broadcasted with several subtitle languages by press LEFT RIGHT key on the remote control If the preset subtitle language could not find in the program the receiver might select the first subtitle language from the program Press MENU key or EXIT key back to the previous menu wi
20. on Highlight Video Resolution item by press UP DOWN key and set the video resolution output as 480P 5761 576P 720P and 10801 to get the excellent video quality on the TV SET by press LEFT RIGHT key Press MENU key or EXIT key to back to the previous menu Please read the 6 4 RESOLUTION to get further more information 24 AV Settings gh 7 1 4 Video Mode Highlight the Video Type item by press UP DOWN key and set the Video output type as PAL NTSC and AUTO by press LEFT DOWN key on the remote control It is corresponding with the program and the TV SET that connected to the receiver AUTO was recommended AV Settings gy 7 1 5 Audio Track Highlight the Audio Track item by press UP DOWN key and set the audio track as Stereo Left Right and Mono by press LEFT RIGHT key on the remote control Stereo was recommended Please read the 6 2 Audio language and audio mode to get further more information 25 AV Settings 1 7 1 6 Digital Audio Output This allows setting the HDMI Coaxial and Optical digital audio output by PCM or AAC AC3 format If you selected AAC AC3 output all digital output switches to includes HDMI Unless your TV set or A V amplifier is supporting HDMI output with AC3 otherwise it causes no sound AV Settings 3 7 2 LANGUAGE SETTINGS Highlight the Language setting item by press UP DOWN key and enter to the Language Settings sub menu by press OK key on the remote control This sub
21. onnector on the Receiver Connect one end of the IEC Power Cable to the Receiver and the other end to power supply Switch on your TV set and the Receiver When the welcome screen is displayed please select the preferred language for the user interface and the country where the Receiver is used by press LEFT RIGHT key Place the cursor to the Installation item by press DOWN key and press OK key to the next step Menu LOHHTI lt t The channel search page will display on the screen and you can select manual search or auto search by press LEFT RIGHT key If you decide to use the Flat Panel Antenna please turn On the Antenna Power Bandwidth tMitz intenna Power Press OK to start the search The Receiver will start to search for available channels and a few minutes are required to complete this operation When a TV channel is detected its corresponding Signal strength and Signal quality are displayed If channel scanning is completed successfully a list of channels found during the scanning process is displayed on screen and you could press EXIT key to exit If no channel is found during the channel scanning process the user may adjust antenna position to obtain optimal TV signal BASIC USE 5 1 INFORMATION BAR Press INFO key to display the information bar during you watch TV program The screenshot is illustration below On the information bar you could find the channel name the LCN the current time and th
22. r requirement specifications It offers users with all digital terrestrial TV and radio signals being broadcast in Standard Definition or High Definition Function 1 Fully complaint DMB T standard 2 Fully complaint MPEG 4 H 264 AVC Main Profile Level 3 and High Profile Level 4 3 Fully complaint MPEG 2 MP HL and MP ML 4 Fully complaint MPEG 1 Layer amp II Dolby Digital Audio 5 174 MHz 858 MHz VHF amp UHF input and LOOP OUT 6 On Screen Display with Multi language 7 4000 Channels capacity 8 Fully support to Electronic Program Guide EPG 9 Picture in Graphics PIG support Auto search and Manual search supported Automatic Save for last channel Parental control for channels Plug and Play installation with an ease to use Menu System Coaxial S PDIF and optical S PDIF Digital audio output interface 5761 576 720 10801 Video Resolution supported 1080P Option Auto 4 3 and 16 9 Aspect Ratio supported EBU Teletext supported DVB or EBU selected by the system based on availability on the network Various channel editing function Group Favorites Move Lock Rename Delete HDMI High Definition Multimedia Interface output with HDCP Revision 1 1 or later at all digital media outputs Software upgrade via USB2 0 interface DC 12V Power Supply CN o0 90uPRONM Main Processor CSM1200 200MHz Memory 8 MB SDRAM 128 MB Base Linux operating system High sensitivity low Eb No for receive Digital T
23. search after setting prefer parameters Install 3 Moe 01605 The entire TV program and radio program should be list on the menu and search successful massage also would display Press MENU key back to the previous menu or Press EXIT key EXIT watch TV VFEDQUESE ees 0016 TV Channels ar RD Channels 0 1 SZTVMO1 Search completed S TVM02 S TVMD3 SETVMO4 6 5 2 Auto Search Press LEFT RIGHT key to select Manual search mode while the installation mode item is highlight You also could set the antenna power supply for the flat antenna if it is necessary Press OK key to start auto search after setting prefer parameters nstall One massage box would remind the entire channels would be cleared if you launch auto search Press OK to launch auto search nstall Warning Clear all services Press OK to confirm Press EXIT to cancel 6 6 CHANNEL EDIT Press MENU key on the remote control and move the cursor to the Channel Edit then press OK key to confirm The channel edit menu allow the user lock prefer channel delete the channel sort the channel and set the interest channel as favorite s channel Press TV R key on the remote control to switch TV program and radio program Frequency 722000 Kilz O delete Brav 20 6 6 1 Delete Channel Press RED key to delete the highlight channel on channel edit menu An X icon would be display on the left of
24. th save setting Please read the 6 3 Subtitle to get further more information Language Settings 3 ransparemni 7 2 4 Teletext Language Highlight the Teletext Language item by press UP DOWN key and preset the preferred subtitle language when a programme is broadcasted with several Teletext languages by press LEFT RIGHT key on the remote control If the preset Teletext language could not find in the program the receiver might select the first Teletext language from the program Press MENU key or EXIT key back to the previous menu with save setting Please read the 6 6 TELETEXT to get further more information 28 Language Settings 1 ud ia Subtitle lransparens 7 2 5 Transparency Highlight the Transparency item by press UP DOWN key and preset the preferred transparency of the menu by press LEFT RIGHT key on the remote control Default value is 20 Press MENU key back to the previous menu or Press EXIT key EXIT and save setting Language Settings 3 11 Menu Language 7 3 TIME SETTINGS Highlight Time Settings item by press UP DOWN key on the remote control and enter to the Time Settings sub menu by press OK key The Time Settings sub menu allows the setting of time preferences The following options are available in the Time Settings sub menu Time mode and Time Zone Highlight the item on the Time Settings sub menu by press UP DOWN key and enter to the next sub menu by press OK key Time zone of
25. the RIGHT button to enter a sub menu Call up a program list for the current channel while watching digital TV or listening to the radio In a menu this button serves to confirm a selection PGUP PGDW Page up down in lists so Display favorites channel PVR Display PVR manager page Record Press Record key to record the current program during watch TV program STOP Press STOP key to stop recording program or stop program during watch PVR program Playing or pause the program during watch PLAY PAUSE PVR program 56 56 Switch resolutions of video output 576i RES ASPECT 5761 PGDW Press ASPECT key to select suitable aspect ASPECT ratio of the video output TEXT TELETEXT function key SUBTITLE Switch between different subtitles AUDIO Press AUDIO key to set the audio track and audio mode OK Wu 58 RES Switch resolutions of video output BATTERY INSTALLATION Insert the batieries while observing the correct and polarities as illustrated below About the batteries Iftheremote control unitfails to work even when itis operated nearthe LCD TVimonitor please replace the batteries Use size UM 4 AAA batteries Notes Donot use rechargeable Ni Cd batteries Donotattemptto recharge short circuit disassemble heat or throw the batteries into the fire Donot drop step on orcause any impact to the remote contro unit This may damage it resulting malfunction Donct mix old
26. to the system settings menu The sub menu was including AV Settings Language Settings Time Settings PIN Settings Network Settings and Factory Reset 22 Main Menu 7 1 AV SETTINGS The AV Setting sub menu allows the user to select an appropriate video and audio output signals to your television set Highlight AV Setting in the System Setting sub menu and press the OK button on the remote control unit to enter the AV Setting sub menu System Setting The following options are available under the AV Setting sub menu Aspect Ratio Aspect Mode Video Resolution Video Type Audio Track and Digital Audio output AV Settings 23 7 1 1 Aspect Ratio Highlight Aspect Ratio item by press UP DOWN key and set the aspect ratio as 4 3 or 16 9 by press LEFT RIGHT key It is corresponding with the TV SET that connected to the receiver Press MENU key or EXIT key to back to the previous menu with save setting Please read the 6 5 ASPECT RATIO to get further more information AV Settings 1 7 1 2 Aspect Mode Highlight Aspect Mode item by press UP DOWN key and set the aspect mode as Letterbox Pan Scan and Full screen by press LEFT RIGHT key to get the prefer picture on the TV SET It is corresponding with the stream and the TV SET that connected to the receiver Press MENU key or EXIT key to back to the previous menu Please read the 6 5 ASPECT RATIO to get further more information AV Settings Pei 7 1 3 Video Resoluti
Download Pdf Manuals
Related Search