Gibson G FORCE Owner`s Manual 2.32 Gibson Brands Revision 1.05
Contents
1. 28 Page BATTERY INFORMATION e A rechargeable battery has long service life if treated properly A new battery or one that has not been used for a long period of time could have reduced capacity the first few times it is used e Do not expose the battery to extreme temperatures and never above 55 C 131 F e For maximum battery capacity use the battery at room temperature Lower temperatures reduce battery capacity e Charge the battery only at temperatures between 10 C 50 F and 45 C 113 F BATTERY STORAGE e Ifthe battery will not be used for a while store it at about half its charge BAT LED yellow e For maximum life store in a refrigerator not freezer in a sealed plastic bag After removing from the refrigerator keep it in the bag until it reaches room temperature to prevent atmospheric condensation around the battery BATTERY CAUTIONS e Do not connect improperly e Do not dispose of in fire or expose to excess heat e Do not crush puncture incinerate or short circuit external contacts e Do not put the battery in a pocket with metal objects keys coins etc BATTERY RECYCLING Your G FORCE battery must be disposed of properly and never placed in municipal waste 29 Page2. E string flashes red Use the Left Right buttons to select the string you tuned to the new reference pitch Pluck the string When the string LED shines green and all others red strum to tune the guitar LEDs turn off reference tuning is complete G Firmware Version Display Gibson G FORCE firmware version number With Gibson G FORCE off press On three times Press Enter Press the Left button three times to select the white G string LED Press Enter You ll see three sequences of lit LEDs The number of lit green LEDs is the version number s first digit the number of lit blue LEDs is the second digit and the number of lit red LEDs is the third digit All white LEDs zero Example 2 lit green LEDS 3 lit blue LEDs 1 lit red LED version 2 3 1 The sequence occurs rapidly If you need to see it again press Enter 12 Page Battery Level Check battery charge 1 With Gibson G FORCE off press On three times Press Enter 2 Press the Left button four times selects the white B string LED Press Enter More lit LEDs stronger charge If only one or two red LEDs are lit recharge the battery 3 The status indication occurs rapidly If you need to see it again press Enter e Temporary Global Tuning Offset Change reference from A 440 Hz to between 434 Hz and 446 Hz A 440 Hz is an international tuning standard However some orchestras tune to A 442 Hz or 443 Hz and some musicians tune to a higher pitch for a brighte
3. Enter Gibson G FORCE enters Single String Tuning mode Use the Left Right buttons to select a string whose tuning you want to add to the base tuning The string LED will be red Pluck it When the string LED turns green select another string see step 4 you want to add to the tuning If you re done turn off the system by pressing and holding the On button You can now turn the system back on and save this as a custom tuning see A Custom Tuning and A Custom Tuning with Pitch Assist Mode on page 11 Gibson recommends using Pitch Assist mode when saving the morphed tuning as a custom tuning 22 Page Appendix 1 What the String BAT and MENU LEDs Colors Indicate e While a string is tuning the string LED color shows the string s status e The BAT LED displays three levels of battery strength e The Menu LED indicates the currently selected Function e ameme O OO e sinrerotinune pusana Frequency out ot messurementrange e hsocatea machine esting o Frequency measurement n progres o Interference between higher and lower strings Battery LED O Battery fully charged e Battery is low Recharge battery Menu LED pe rmes OOOO o Tirer o renaren O havancestardnare Funcions cateson o havances sofware Funcom category e simneprcnotserceeon e aoaunboccoans caeso o flashing Capo mode 23 Page Appendix 2 Minimum and Maximum String Frequencies for Alternate Tunings Please note these are
4. The Left button enables writing to the selected bank e B G LEDs flash green The Right button write protects the selected bank D A E LEDs flash red 4 Press Enter Green or red LEDs light sequentially to confirm your choice 5 You can now save a custom tuning to any write enabled bank Note If a bank is blocked you will not be able to access it with the Up Down buttons when saving a custom tuning see page 11 However the blue bank is a special case When you create a custom tuning you are first given a chance to save to the blue bank regardless of whether it s blocked so that even if all the other banks are blocked you can still save your tuning However as soon as you use the Up Down buttons to select a different bank to save a custom tuning the blue bank will no longer be available if it s blocked 20 Page Capo Mode Adding a capo often requires retuning a guitar Gibson G FORCE can detect a capo in the range of the 1 to 6 frets then tune while taking the capo position into account Yes this is amazing Enter Capo Mode 1 Capo Mode applies to the last completed tuning Select and tune to a tuning preset prior to entering Capo Mode 2 Once Gibson G FORCE has turned off attach your capo on the 1 to 6 frets 3 Press On twice Press and hold the Left button Green LEDs light sequentially capo mode is active 4 Press Enter and strum to tune your guitar Gibson G FORCE briefly indicates capo detection the nu
5. but handed over to the applicable collection point for the recycling of electrical and electronic equipment By ensuring this product is disposed of correctly you will help prevent potential negative consequences for the environment and human health which could otherwise be caused by inappropriate waste handling of this product The recycling of materials will help to conserve natural resources For more detailed information about recycling of this product please contact your local city office your household waste disposal service or the shop where you purchased the product POWER SUPPLY CAUTIONS Connect the AC power adapter only to power sources as designated on the product To reduce risk of damage to the electric cord remove the AC adapter from the outlet by holding onto the AC adapter rather than pulling on the cord Position the cord so it cannot be stepped on tripped over or otherwise subjected to damage or stress To reduce risk of electric shock unplug the unit from any power source before attempting to clean it The AC power adapter must not be used outdoors or in damp areas DANGER Never alter the AC cord or plug If the plug will not fit into the outlet have a proper outlet installed by a qualified electrician Improper connection can result in risk of electric shock NOT SUITABLE FOR CHILDREN Do not allow children to play with G FORCE because it contains small parts that could become detached and create a choking hazard
6. fret at 25 Page the desired note for the custom tuning and pluck the associated string Continue until all six strings are green after which they ll flash and turn off Tip Mute a string after its string LED turns green to speed up the process 4 When a string LED flashes blue use the Left Right buttons to select a blue bank preset Press Enter stores pitch corrected tuning in the selected preset Do not turn off Gibson G FORCE yet it needs to learn how to tune to this tuning 5 Press the On button twice to return to Tuning Bank selection Use the Up and Down buttons to select the blue bank if needed and the Left and Right buttons to select the preset you stored In step 4 above 6 Press and hold the Enter button for Single String Tuning mode 7 Pluck the string with the flashing red LED After its LED turns green wait for another string LED to flash red then pluck the associated string Tip Mute a string after its string LED turns green to speed up the process 8 When all six LEDs are green all six strings are tuned Gibson G FORCE turns off When you tune using this tuning G FORCE will apply the stored pitch correction Note Alternate tunings can change the neck tension After the single string tuning refreshing the tuning in Multi String mode can compensate for this Quick Single String Tuning Mode for Alternate Tunings As described in the Quick Start you can use Multi String tuning with alternate tuni
7. guidelines that will vary depending on the string gauges you use The maximum recommended string gauge is 0 013 for high e to 0 056 for low E Minimum Frequencies Lowest Corresponding Note for Low Tunings E 60Hz 47Hz GAH A80OHz 63Hz C2 6541H D112Hz 89Hz AZ 9250W JE 250Hz 198Hz Ab3 207 65Hz Maximum Frequencies Highest Corresponding Note for E102 4 9B HZ G 240H4 A 233 08H2 y O E400 z7 BBA 24 Page Appendix 3 Custom Alternate Tuning Tips and Shortcuts Tuning Shortcut for Tunings with Lower Pitched Strings If your custom tuning consists of strings that are lower pitched than standard tuning there s a quick way to create a custom tuning You can then save this as you would any custom tuning 1 With Gibson G FORCE off press and hold the On button until the red E LED lights 2 Pluck the string with the red LED but if you want it tuned lower than standard fret at the fret that equals the number of semitones you want to tune down Example To tune the low E string down to D two semitones lower than E fret F on the low E string two semitones higher than E When its LED is green pluck the next string with a red LED 3 If you don t want to change a string s tuning simply pluck it If you want to tune it lower follow the procedure in step 2 4 After plucking each string individually until its LED is green all six strings are tuned to a custom tuning Gibson G FORCE turns off Now save
8. this custom tuning using pitch assist so G FORCE compensates for any errors introduced by fretting the string 1 Press On three times Press Enter Press the Left button once to select the white A string LED then press and hold Enter for more than 3 seconds to engage Pitch Assist 3 When a string flashes red pluck it Continue until all six strings are green at which point they ll flash and turn off Tip Mute a string after its string LED turns green to speed up the process 4 When a string LED flashes blue use the Left Right buttons to select a blue bank preset Press Enter stores pitch corrected tuning in the selected preset When you tune using this tuning G FORCE will apply the stored pitch correction Custom Tuning Shortcut for Tunings with Higher Pitched Strings If your custom tuning consists of strings that are higher pitched than standard tuning there s a quick way to create a custom tuning You can then save this as you would any custom tuning 1 With Gibson G FORCE off press On three times Press Enter Press the Left button once to select the white A string LED then press and hold Enter for more than 3 seconds to engage Pitch Assist 3 When a string LED flashes red if needed fret at the desired note for the custom tuning then pluck the associated string After measuring the frequency the string LED will turn green Wait for another string LED to flash red this can take several seconds then again if needed
9. Category E String Up Down Wind or unwind strings rapidly 1 With Gibson G FORCE off press On three times Then press Enter twice 2 The LED for the string to wind or unwind flashes red The Left Right buttons select a string 3 Press and hold Down to wind down Up to wind up CAUTION When winding up do not wind higher than the target pitch because the string might snap Note During String Up Down Single String Tuning Mode tunes each string individually is active When approaching the correct pitch during string wind up release the Up button and pluck the string A flashing yellow string LED indicates the string is close to the pitch defined by the last completed tuning Gibson G FORCE takes over tunes the string to pitch then moves automatically to the next string If tuning starts but does not complete pluck the string again A Custom Tuning Create a custom tuning then store it as a user tuning preset in the blue tuning preset bank See Appendix 3 and Appendix 4 for more custom tuning options With Gibson G FORCE off tune your guitar to a custom tuning Press On three times Press Enter Press the Left button once to select the white A string LED then press Enter oo a When a string flashes red pluck it Tip Mute a string after its string LED turns green to speed up the process 5 When a string LED flashes blue use the Left Right buttons to select a blue bank preset Press Enter stores the tuning in the select
10. Gibson G FORCE Owner s Manual 2 32 Gibson Brands Revision 1 05 The Gibson Perfect Contents 03 04 05 06 09 09 11 11 11 11 12 12 13 13 14 14 15 15 15 16 16 16 17 17 17 17 18 18 19 20 21 22 23 24 25 27 28 Basic Gibson G FORCE Functions Start Here Main Tuning Preset Bank Default Tunings Low Tuning Preset Bank Default Tunings Re Stringing Guitars with Gibson G FORCE Changing the Gibson G FORCE Battery Overview How to Choose Access and Edit Advanced Functions Tuning Functions White Category E String Up Down A Custom Tuning A Custom Tuning with Pitch Assist Mode D Reference Tuning Firmware Version B Battery Level e Temporary Global Tuning Offset Reset Function Red Category Master System Reset Red Category Advanced Hardware Functions Cyan Category E Calibration Mode A Accuracy D Machine Head Delay G Machine Head Speed B Interference Filter Advanced Software Functions Yellow Category E Gain A Guitar Type D Pitch Window G Activate Low Tunings and or Additional User Tuning Preset Banks B Tuning Offset Mode Permanent or Temporary Per String Pitch Offset Magenta Category Block Unblock Banks for Custom Tunings Blue Category Capo Mode Combine Morph Tunings Appendix 1 What the String BAT and MENU LEDs Colors Indicate Appendix 2 Minimum and Maximum String Frequencies for Alternate Tunings Appendix 3 Cus
11. d the top part of the post wind it directly on top of the flange not partway up the upper part of the post Wrap two full turns for the B and high e strings Wind the strings in the same direction clockwise as the direction of tightening the machine head cap Make sure to wrap two full turns with the B and high e string before tightening the cap 6 After wrapping the string around the top part of the post pull it tight with one hand as you screw on the cap with the other hand 7 Screw the cap on as tight as you can with your fingers then use a penny to give an additional 1 8 turn Do not overtighten 8 Use String Up mode see page 11 to tune the string 8 Page Changing the Gibson G FORCE Battery A fully charged battery provides approximately 100 tunings more if you re just touching up Please read Appendix 5 page 27 for information about proper battery care and charging To remove the battery The battery compartment is located in the Gibson G FORCE controller on the back of the headstock Push down on the rectangle that s visible at the top of the controller between the machine heads for the 3 and 4 strings The battery will pop up slightly Note the groove facing outward at the top of the battery and use it to pull the battery out of its compartment To insert the battery Never force the battery into its compartment If it does not insert easily it is not being inserted correctly Insert the batter
12. ed preset A Custom Tuning with Pitch Assist Mode Create a custom tuning then store it as a pitch corrected user preset in the blue tuning preset bank Enabling Pitch Assist mode before saving a custom tuning automatically pitch corrects notes that are within 40 cents of correct pitch 11 Page With Gibson G FORCE off tune your guitar to a custom tuning Press On three times Press Enter Press the Left button once to select the white A string LED then press and hold Enter for more than 3 seconds to engage Pitch Assist When a string flashes red pluck it Tip Mute a string after its string LED turns green to speed up the process When a string LED flashes blue use the Left Right buttons to select a blue bank preset Press Enter stores pitch corrected tuning in the selected preset D Reference Tuning Tune the guitar to itself but reference a non standard pitch Example A piano is in tune with itself but slightly flat Tune one string to the piano make that the reference pitch and the guitar will be in tune with the piano Note Loading any other tuning erases the reference tuning To save this tuning as a user tuning preset treat it as a Custom Tuning and follow the steps in A Custom Tuning above Do not use Pitch Assist a o oS With Gibson G FORCE off tune one string to the new reference pitch Press On three times Press Enter Press the Left button twice to select the white D string LED Press Enter
13. eed Slow the machine head speed to accommodate guitars whose neck relief or neck stability degrades tuning accuracy a With Gibson G FORCE off press On three times Press the Left button once to select cyan A Press Enter Press the Left button three times to select the cyan G string LED Press Enter Use the Left Right buttons to select the speed Each unlit LED decreases the speed Press Enter speed setting stored B Interference Filter Reduce interference among strings if a machine head turns for a string other than the one you re plucking With Gibson G FORCE off press On three times Press the Left button once to select cyan A Press Enter Press the Left button four times to select the cyan B string LED Press Enter Use the Left Right buttons to select the filtering amount Each unlit LED increases the filtering amount to reduce interference Press Enter interference filter setting stored Note Raising this setting to six lit LEDs may increase performance but make the e and B strings more susceptible to incorrect tuning even if G FORCE indicates they are in tune If this occurs lower the Interference Filter setting to three or four lit LEDs 16 Page Advanced Software Functions Yellow Category E Gain Increase gain if string LEDs don t turn yellow when first plucked decrease gain in environments with high ambient noise The default is recommended 1 With Gibson G FORCE off press On three times Press t
14. get s G back in tune to the new default tuning Y see D Return to Standard Tuning H ahe h _ re 1 Press the On button two times het 2 Press Up Down for the red tuning bank then press Left Right until the red E LED is on Press Enter strum once Standard tuning is now the default currently selected tuning E You can turn off Gibson G FORCE by pressing and holding the ON button Do s and Don ts e Don t use string winding tools Besides Gibson G FORCE s string up string down function is better e Don t tune manually while Gibson G FORCE is on e Doread Appendix 5 and Appendix 6 for important safety information about Gibson G FORCE e Do recalibrate the guitar page 15 after changing string gauge or string type e Do check the BAT LED periodically Green charged yellow acceptable red time to recharge e Do charge the battery before using Gibson G FORCE for the first time e Do read the rest of the manual to take advantage of the optional advanced Functions e Do visit www gibson com gforce for news about the Gibson G FORCE system 3 Page Main Tuning Preset Bank Default Tunings string E A D G B e Ce 8 E 6 aA o a e Ee a gt A i o a o p wholes o e c rf aA v e o a o C Ce Ab b e doubiedropD o a o e ro iD e E e string E A D B e ree T Blue User Tuning Preset Bank string E A D G B e fs a ee Y A Os D SS Se ee ee Ca B DEE ee eee a The blue
15. he Left button twice to select yellow D 2 Press Enter twice The Left Right buttons select the gain amount More lit LEDs higher gain greater system sensitivity 3 Press Enter gain setting stored Note The Calibration process page 15 optimizes gain Gibson strongly recommends keeping the default Gain setting However when tuning in loud environments decreasing gain temporarily and tuning in Single String Tuning mode can improve performance A Guitar Type Optimize Gibson G FORCE for electric or acoustic guitar With Gibson G FORCE off press On three times Press the Left button twice to select yellow D Press Enter Press the Left button once to select the yellow A string LED Press Enter The Left Right buttons select E for electric A E for acoustic or D A E for short scale guitars Press Enter guitar type setting stored oe Se D Pitch Window If you try to use Multi String tuning mode but a string is considerably out of tune Gibson G FORCE switches automatically to Single String Tuning mode This Function sets how far off pitch a string must be before Gibson G FORCE switches to Single String Tuning mode 1 With Gibson G FORCE off press On three times Press the Left button twice to select yellow D Press Enter 2 Press the Left button twice to select yellow D Press Enter 3 The Left Right buttons select the pitch window 1 lit LED 150 cents 2 lit LEDs 100 cents 3 lit LEDs 75 cents 4 lit LEDs 50 cents 5
16. ht button lights magenta LEDs Each lit magenta LED offsets the pitch by another 1 cent 12 cents maximum e lf an offset already exists Gibson G FORCE displays the offset amount as described above In this case Right or Left button presses continue on from the existing offset Example If 12 magenta LEDs are lit to indicate 12 cents of offset pressing the Left button will turn off successive magenta LEDs then turn off successive red LEDs then start lighting green LEDs 4 Press Enter To offset additional strings repeat steps 2 4 Otherwise press and hold the On Back Off button to turn off Gibson G FORCE 19 Page Block Unblock Banks for Custom Tunings Blue Category Turn write protection on or off for any tuning preset bank The blue bank defaults to a user tuning preset bank for custom tuning presets For low tunings the magenta bank see G Activate Low Tunings and or Additional User Tuning Preset Banks on page 18 defaults to a user tuning preset bank for custom tunings low tunings or otherwise The remaining banks contain factory tuning presets and are write protected However any of the six banks can have write protection turned off to store custom tunings or turned on to prevent overwriting custom tunings 1 With Gibson G FORCE off press On three times Press the Left button four times to select blue B 2 Press Enter The Left Right buttons select the color of the bank to write enable or write protect 3 Press Enter
17. lit LEDs 35 cents all LEDs lit 25 cents 4 Press Enter pitch window setting stored 17 Page G Activate Low Tunings and or Additional User Tuning Preset Banks Opens three additional tuning preset banks White Yellow and Magenta This Function activates three additional tuning preset banks The White and Yellow banks default to write protected presets for music with low tunings heavier gauge strings up to 0 013 high e to 0 056 low E are necessary for low tunings The Magenta bank like the Blue bank defaults to being write enabled for storing user tuning presets However you can also convert any of these banks to user tuning preset banks and store presets in them See Block Unblock Banks for Custom Tunings Blue Category on page 20 for details With Gibson G FORCE off press On three times Press the Left button twice to select yellow D 2 Press Enter Press the Left button three times to select the yellow G string LED Press Enter 3 The Left button activates low tunings and additional preset banks e B G LEDs flash green The Right button de activates low tunings and additional preset banks D A E LEDs flash red 4 Press Enter low tuning additional banks setting stored B Tuning Offset Mode Permanent or Temporary The Global Tuning Offset white category is temporary and applies only until loading a new tuning preset This Function retains offset when changing tuning presets 1 With Gibson G FORCE off press On
18. mber of lit yellow LEDs indicates the capo s location Example Two lit yellow LEDs capo at second fret Then tuning proceeds as usual Note Whenever you tune in capo mode Gibson G FORCE first indicates capo location by the number of lit yellow LEDs 5 If any string LEDs aren t green pluck those strings Gibson G FORCE turns off automatically once tuning is complete Exit Capo Mode Two Options e Remove the capo Next time you tune as soon as you strum Gibson G FORCE will detect there is no capo red LEDs will flash sequentially to turn off Capo Mode and Gibson G FORCE will confirm there is no capo by briefly shining all blue LEDs Continue with tuning e If you don t want to retune after removing the capo starting with Gibson G FORCE off follow steps 3 and 4 above Red LEDs will light sequentially instead of green ones to indicate exiting from Capo Mode Press and hold On to power down Gibson G FORCE Remove the capo 21 Page Combine Morph Tunings Apply selected string tunings from one tuning to a different tuning Tune to a base tuning preset to which you will add string tunings from a second tuning preset Press On twice then select the second tuning preset Up Down buttons select the tuning preset bank Left Right buttons select the tuning preset Please read this entire step before doing any of its instructions Press and hold the Right button The Menu LED will flash white rapidly While it s flashing press
19. ng up through the flange recess that faces the tuning pegs String winding technique The string shaft slot where to feed the string up toward the thread is at an approximate 45 degree angle The guitar body is below the picture 6 Page 4 Wind one turn clockwise around the part of the post directly above the flange Wind the strings in the same direction clockwise as the direction of tightening the machine head cap 5 Screw the cap on as tight as you can with your fingers then use a penny to give an additional 1 8 turn Do not overtighten 6 Use String Up mode see page 11 to tune the string Treble Side Guitar Stringing for Gibson G FORCE 1 Remove the machine head cap 2 Looking at the headstock from the top and with the treble strings toward the right the machine head s right recess should be between 1 00 and 2 00 o clock and the left recess between 7 00 and 8 00 o clock The red line indicates a 45 degree angle 3 Thread the string through the bridge and toward the machine head Pull on the string to take up any slack as you wrap it partially around the part of the post below the flange that faces away from the guitar body 4 Bring the string up through the recess in the flange and wind clockwise around the part of the post just above the flange 7 Page String slot shaft where to feed the string up toward the thread with an approximate 45 degree angle 5 When you wrap the string aroun
20. ngs However you can also go immediately into Single String tuning mode 1 Press the On button two times 2 Press Up Down to scroll through tuning preset banks red green blue or additional ones that are unblocked see page 20 3 Press Left Right to choose individual tunings 4 Press and hold Enter for 2 seconds or until the lights flash green The machine heads turn to come close to the tuning and automatically selects single string mode 5 Pluck the string with the red LED Pluck each string individually until its LED is green and Gibson G FORCE goes automatically to the next string 6 When all LEDs are green all strings are tuned to the currently selected tuning Gibson G FORCE turns off 26 Page Appendix 4 Changing Charging the Gibson G FORCE Battery A new or infrequently used battery could have a reduced capacity and need recharging several times to restore full capacity When the battery level is low the Gibson G FORCE BAT LED located on the controller flashes red Caution e Do not connect improperly e Do not dispose of in fire or expose to excess heat e Donotcrush puncture incinerate or short circuit the external contacts e Do not put the battery in a pocket with metal objects keys coins etc e Never force the battery into the guitar s battery slot It should slide in easily see page 9 XN F A g LE C G2 J gq 2 BATTERY IS CHARGING BATTERY IS CHARGED AWE Gpp ans ee Pida qe Tam
21. ns off automatically if any LEDs aren t green pluck those strings individually Calibration 1 Press On three times Press the Left button once selects cyan A Press Enter twice The string LEDs blink red 3 Strum once All lights should shine green briefly then turn off If the LEDs continue to flash red mute the strings and strum again 4 Once the strings have turned off from being green or show a combination of blue and red LEDs mute the strings Then all string LEDs blink red 5 Repeat steps 3 and 4 until the LEDs light sequentially and one string LED is lit Accuracy Balance tuning accuracy vs speed 1 With Gibson G FORCE off press On three times Press the Left button to select cyan A Press Enter 2 Again press the Left button to select cyan A Press Enter 3 The Left Right buttons select the accuracy More lit LEDs higher accuracy tuning takes a little longer Fewer lit LEDs accuracy is a little lower faster tuning speed 4 Press Enter accuracy setting stored 15 Page D Machine Head Delay Set a delay before the machine heads start turning after initiating a Function i With Gibson G FORCE off press On three times Press the Left button once to select cyan A Press Enter Press the Left button twice to select the cyan D string LED Press Enter The Left Right buttons select the delay Each unlit LED increases delay by 0 5 seconds Press Enter delay setting stored G Machine Head Sp
22. press Enter e Each Category has an associated color Examples The Yellow Category is mostly advanced software functions The Magenta Category handles string pitch offsets e When choosing a Category the Menu LED flashes the Category color Functions Each Category offers various Functions e After selecting a Category press the Left Right buttons to select a Function within the Category and then press Enter to access the Function e When the Menu LED lights solid with the Category color you can edit the Function with the Up Down Left Right and Enter buttons On Back Off button The On button becomes a Back button when editing It can also turn Gibson G FORCE Off e f Gibson G FORCE is in a Function press the On Back button to return to the Function s Category e Press the Back button again and Gibson G FORCE is in Tuning Selection mode e Press and hold the On Off button to turn off Gibson G FORCE if G FORCE doesn t turn off release the button then press and hold again After pressing Enter to complete a Function Gibson G FORCE usually returns to Function selection so you can select another Function quickly Or if you re done press and hold the On Off button to turn off Gibson G FORCE Note Please read the important legal and safety information regarding Gibson G FORCE in Appendix 5 page 27 and Appendix 6 page 28 prior to using Gibson G FORCE 10 Page Advanced Functions Tuning Functions White
23. r sound 1 With Gibson G FORCE off press On three times Press Enter Press the Left button five times to select the whiite e string LED Press Enter All string LEDs flash white If an offset already exists Gibson G FORCE displays the offset amount with lit green or red LEDs see next 4 Each Left button raises pitch by 1 Hz press and lights a green LED Each Right button press lowers pitch by 1 Hz and lights a red LED 5 Press Enter to store the offset temporarily Note Gibson G FORCE applies this offset when you tune using the current tuning preset Loading a new tuning preset reverts to the 440 Hz standard To retain the offset until you change it see the Yellow category B Tuning Offset Mode Permanent or Temporary on page 18 13 Page Reset Function Red Category Restore factory default tuning presets for the selected tuning preset bank 1 With Gibson G FORCE off press On three times 2 Press the Left button five times selects red e string LED 3 Press Enter Use the Left Right buttons to select the string LED associated with the Function below The remaining procedure is the same for each Function E Reset Red Tuning preset bank A Reset Green Tuning preset bank D Reset Blue Tuning preset bank G Reset White Tuning preset bank B Reset Yellow Tuning preset bank e Reset Magenta Tuning preset bank 4 Press and hold the Enter and Up buttons simultaneously by pushing in the space between them while holding
24. reel eer LR Le Yn Cap T ATOM HAAFERCER HYPE AoE Charging e Use only the charger supplied with your guitar Other chargers could damage the battery the charger or both e The charger s LED shines red when charging and green when the battery is charged e Charge the battery when the BAT LED on the controller shines red or when yellow to maintain a full charge Battery Pack 3 7V 340mAh 1258mWh Li Polymer Li Polymer Charger Input 100 240V AC 50 60HZ Output 4 2V 300mA Charger tip polarity Om a O 27 Page Appendix 5 Gibson G FORCE Legal and Safety Information Please read this information before using Gibson G FORCE PRODUCT CARE Do not expose your product to liquids moisture or humidity Do not expose your product to extreme high or low temperatures Do not expose your product to lit candles cigarettes or cigars open flames or other heat sources Do not drop throw or try to bend the product Rough treatment could damage it Do not attempt to disassemble your product It does not contain consumer serviceable or replaceable components Only Tronical GmbH or a Gibson Brands service facility should perform servicing If you will not be using the product for a while store it in a place that is dry and free from moisture dust and extreme temperatures DISPOSAL OF ELECTRICAL AND ELECTRONIC EQUIPMENT This symbol on the product indicates that it must not be treated as household waste
25. three times Press the Left button twice to select yellow D 2 Press Enter Press the Left button four times to select the yellow B string LED Press Enter 3 The Left button selects permanent tuning offset e B G LEDs flash green The Right button selects temporary tuning offset D A E LEDs flash red 4 Press Enter tuning offset mode setting stored 18 Page Per String Pitch Offset Magenta Category Offset any string s individual pitch up to 12 cents a cent is 1 100 of a semitone Note Pitch Offset applies to the last completed tuning Please choose select and tune to a tuning preset before applying per string pitch offset Pitch offset will remain applied to this tuning until you change its pitch offset reset the bank or reset the system 1 With Gibson G FORCE off press On three times Press the Left button three times to select magenta G Press Enter 2 The Left Right buttons choose the magenta string LED for the string you want to offset Press Enter 3 Press the Left Right buttons to enter the string s pitch offset e If no previous offset exists all string LEDs flash white Each Left button press lights a green LED and offsets pitch by 1 cent up to 6 cents Continuing to press the Left button lights yellow LEDs Each lit yellow LED offsets the pitch by another 1 cent 12 cents maximum e Each Right button press lights a red LED and offsets pitch by 1 cent up to 6 cents Continuing to press the Rig
26. tom Alternate Tuning Tips and Shortcuts Appendix 4 Charging the Gibson G FORCE Battery Appendix 5 Gibson G FORCE Legal and Safety Information 2 Page Basic Gibson G FORCE Functions Start Here A Multi String Tuning 1 Press On button Strum once G FORCE tunes to the currently selected tuning 2 When all LEDs are green all six strings are tuned Gibson G FORCE turns off automatically If any LEDs remain red mute then pluck those strings one at a time until they turn green B For a Little More Precision Single String Tuning Spend a Few More Seconds Tune One String at a Time 1 Press and hold the On button until the red E LED lights 2 Pluck the string with the red LED Pluck each string individually until its LED is green and Gibson G FORCE goes automatically to the next string 3 When all LEDs are green all strings are tuned to the currently selected tuning Gibson G FORCE turns off C Here s The Really Great Part Play In a Different Tuning 1 Press the On button two times K aN 2 Press Up Down to scroll through tuning preset banks red green RNS blue e h 3 Press Left Right to get to individual tunings 4 Press Enter briefly wait until all LEDs are red strum once the tuners start working when you press Enter 5 When all LEDs are green all six strings are tuned Gibson G FORCE a a turns off ora 6 The new tuning is now your default Just do either A or B to
27. user tuning preset bank defaults to standard tuning E A D G B e Use the chart to write in custom tuning names and tunings 4 Page Low Tuning Preset Bank Default Tunings White Low Tuning Preset Banks string E A D G B e S a eming e r m o a wwe c e o ce A o csap o e e Betung e e a o m e s droppedc o e c r A e droppedB e m e e e string Magenta User Tuning Preset Bank ee string E A D G B e LED The magenta user tuning preset bank defaults to standard C tuning C F A D G C Use the chart to write in custom tuning names and tunings 5 Page Re Stringing Guitars with Gibson G FORCE For proper Gibson G FORCE operation re string your guitar following these instructions To maintain a constant neck tension Gibson recommends changing strings individually Bass Side Guitar Stringing for Gibson G FORCE 1 Unscrew the machine head cap 2 Looking at the top of the headstock with the bass strings toward the left the machine head s right recess should be between 4 00 and 5 00 o clock and the left recess between 10 00 and 11 00 o clock Low E string machine head detail The guitar body is below the picture 3 Thread the string through the bridge and toward the machine head Pull on the string to take up any slack as you wrap it partially around the part of the post below the flange that faces away from the guitar body Then bring the stri
28. y with its two metal contacts facing outward and away from the headstock and the pins pointing downward into the compartment Push downward gently on the top of the battery until you hear feel a click If the top of the battery is flush with the top of the controller it s seated correctly Overview How to Choose Access and Edit Advanced Functions Gibson G FORCE is easy to use The most common functions tuning a guitar to standard and alternate tunings take a few button presses The string LEDs from E for the 6 lowest pitched string to e for the 1 highest pitched string show the system status Battery LED up Menu LED right enter String LEDs left down on back off Gibson G FORCE stores standard alternate and custom tunings in presets Each preset contains a tuning This can be a factory default tuning or a custom tuning you create and store Follow the simple instructions in the Quick Start guide and your guitar will always be in tune 9 Page However Gibson G FORCE is like a video game with additional levels These levels offer advanced tuning functions Use them or not it s your choice Here s an overview of how to choose access and edit the advanced functions Categories Gibson G FORCE has six main Categories e After pressing the On button three times don t press too fast each one should be about a second apart press the Left Right buttons to select a Category and then
29. your finger over both buttons 5 LEDs with the same color as the bank flash sequentially reset confirmed To reset additional banks repeat steps 3 5 Master System Reset Red Category Restore Gibson G FORCE to original factory settings also highly recommended when changing string gauges Note This procedure erases all custom tunings With Gibson G FORCE off press On three times Press the Left button five times to select the red e string LED Press Enter Press the Left button six times The E LED lights cyan Press and hold the Enter and Up buttons simultaneously by pushing in the space between them while holding your finger over both buttons Cyan LEDs light sequentially reset confirmed After a reset use Calibration mode to re calibrate the guitar see next section a a le a a 14 Page Advanced Hardware Functions Cyan Category Except for Calibration Mode these Functions are for advanced users only Gibson recommends the default settings E Calibration Mode Note You must recalibrate Gibson G FORCE if e You change your strings gauge type or brand e Performa master system reset e Encounter issues like erratic machine head movements strings not tuning properly etc Before calibration tune the guitar to standard pitch red tuning bank E Function 1 With Gibson G FORCE off press the On button Strum the open strings once 3 When all LEDs are green all six strings are tuned Gibson G FORCE tur
Download Pdf Manuals
Related Search