User`s Manual - Electronic Displays, Inc.
Contents
1. TIMER User s Manual o O O D o O DO E DISPLAY BOARD SECTION 1 KEYPAD LAYOUT 12 24 Key Set 12 24 hour format RST key Reset the Timer U D key The Timer toggles between up time and down time L R key Select the left or right two digits to adjust S 1 key Increase by 1 S 1 key Decrease by 1 START key Run the Timer STOP key Stop the Timer 2 POWER ON SET UP THE DISPLAY BOARD 100 240AV coj 1 Plug the appropriate end of the DC Power Adapter into the power receptacle on the Display Board 2 Plug the DC Power Adapter into a standard 100 240VAC outlet 3 Once the Display Board is powered on it begins to work First It will cycle through a diagnostic display and then run the last selected function 3 SELECT THE DISPLAY BOARD FUNCTION There are function selection switches on the side of the Display Board Below is the function list when selection switches are at different status The Timer function switch FUNCTION SWITCH FUNCTION DISCREPTION o z MODEL 101 Stand alone clock ez kak NO MODEL 102 Up Timer EZL kat NO MODEL 104 Up Down Timer EZL Piafa Note After selecting a new function by selection switches you need to reboot the Display Board to let the new function take effect 4 OPERATION IN2. amp gt denotes the beginning of data package lt ETX gt are ASCII code lt E T X amp gt denotes the end of data package The middle messages between lt STX gt and lt ETX gt may vary according to detailed function or operation 1 Set Display Board ID lt STX gt lt ID gt lt xx gt lt ETX gt lt ID gt ASCII code lt l D amp gt xx the range from 00 to FF the Hex number in ASCII format 1 STAND ALONE CLOCK MODEL 101 lt STX gt lt xx gt lt CLhhmmssy gt lt ETX gt Set the Clock and time format xx denotes the ID of Display Board which the messages will be sent to lt CL are ASCII code lt C L hh denotes hour two ASCII characters mm denotes minute two ASII characters ss denotes second two ASII characters y denotes time format 1 stands for 12hour format and O stands for 24hour format 3 UP DOWN TIMER MODEL 104 lt STX gt lt xx gt lt DAyyyy gt lt ETX gt Send the preset number yyyy the preset number 4 ASCII characters lt STX gt lt xx gt lt SG1 gt lt ETX gt Begin to run the timer lt STX gt lt xx gt lt SG0 gt lt ETX gt Hold the Timer lt STX gt lt xx gt lt UP gt lt ETX gt Begin to up timer lt STX gt lt xx gt lt DN gt lt ETX gt Begin to down timer lt STX gt lt xx gt lt RE gt lt ETX gt Reset the Timer 2 UP TIMER MODEL 102 lt STX gt lt xx gt lt SG1 gt lt ETX gt Begin to run the timer lt xx gt den
3. STRUCTION Stand alone clock Model 101 1 Press 12 24 key will alternate between 24hour and 12hour format 2 To adjust display time first press STOP key to pause the Timer then press L R key to select two digits which will be adjusted The selected two digits will flash 3 Press S 1 or S 1 to set desired number If press S 1 or S 1 for 3 seconds the number will be adjusted quickly 4 Press L R key again to select the other two digits and then adjust to desired number 5 Press START key to finish setting The Timer begins to work Up Timer Model 102 1 Press START key will run the Timer 2 Press STOP key will stop the Timer 3 Press RST key will reset the Timer Up Down Timer Model 104 1 Press START to run the Timer 2 Press U D key will make the Timer alternative between up time and down time 3 To adjust display time first press STOP key to pause the Timer then press L R key to select two digits which will be adjusted The selected two digits will flash 4 Press S 1 or S 1 to set desired number If press S 1 or S 1 for 3 seconds the number will be adjusted quickly 5 Press L R key again to select the other two digits and then adjust to desired number 6 Press START key to finish setting The Timer begins to work 5 COMMUNICATION PROTOCOL Eln terface method RS232 RS485 Baud Rate 9600 bps 8 N 1 BEElData structure lt STX gt message lt ETX gt lt STX gt are ASCII code lt S T X
4. er Model 102 al AE alo SC Fuxtons Hep Ele Secizom Funziens Hef Madel131 Slan oone Docs ken HIN peT Display Board ID fuu zj Display Voard ID Time 21 09 30 WW MMC Time Format 31 Hour 1 gt R TD pe ae i 3 Up Down Timer Model 104 Timer Dimas e alcix De ZetCom uncicns Lep Fox U4 Up oem Liner Display Board ID X y Time 21 11 MINSI SPECIFICATIONS 4 TIMER VIEWING DISTANCE lt 131 Feet 40m DIMENSION 18 450mm Width 5 4 137mm Height 1 8 45mm Depth DISPLAY DIGIT 4 POWER INPUT DC12V CONSUMING POWER 9 Watts El 2 3 TIMER VIEWING DISTANCE lt 75 Feet 23m DIMENSION 11 4 289mm Width 3 5 89mm Height 1 9 47mm Depth DISPLAY DIGIT 4 POWER INPUT DC12V CONSUMING POWER 9 Watts For indoor use only Avoid outdoor storage e Keep away from high temperatures humidity dew water and direct sunlight Always disconnect power cord and other cables by holding plug Clean with damp cloth only 1M062160000
5. otes ID of Display Board to which the messages will be sent to lt SG1 gt are ASCII code lt S G 1 amp gt lt STX gt lt xx gt lt SG0 gt lt ETX gt Hold the Timer lt STX gt lt xx gt lt RE gt lt ETX gt Reset the Timer SOFTWARE SECTION 1 SOFTWARE SCREEN Timer Display E 10 x Eile Set Ccm Funcions Help Model 191 Stand slane Pinak Bere 31 Select Model Model 101 3tand alore Clock Model 102 Jp Timer Model 104 Jp Dowr Timer IV Show this wincow when progam starts Cancel 2 SET UP CONNECTING THE CABLE 1 Connect Display Board to the PC using RS232 RS485 cable 2 On the back of your computer identify a COM PORT If you have trouble locating a COM PORT on your computer please reference your computer user manual or contact the manufacturer of your computer 3 Connect the 9 Pin connector end to the COM PORT you will be using If the 9 pin connector is not connected to the correct COM PORT computer communication will not work z RS232 RS485 f D po B E 3 CONFIGURE SOFTWARE Er 1 Select COM port 3 COM Port com y Select the Com Port 2 Click on OK when your settings are complete 4 SET DISPLAY BOARD ID Msemo 3 1 Select proper ID number 2 Click OK button 5 FUNCTION INTERFACE 1 Stand alone clock Model 101 2 Up Tim
Download Pdf Manuals
Related Search