Arctic AMR Hardware Manual
Contents
1. The device must be powered off and power supply cables removed when installing SIM card If the device has already been powered wait for 5 minutes after all the LEDs have been disabled before opening the device Firmware Version 1 x 12 Document Version 1 1 Hardware Manual M 10 LAW Arctic AMR Hardware Manual Figure 3 Before SIM Installation When the device is opened gently push and slide SIM holder for opening the cover Insert the SIM card to the cover of the holder and close the SIM holder in the reversed order Figure 4 SIM holder open for installing the SIM card Firmware Version 1 x 13 Document Version 1 1 Hardware Manual M 10 LAW Arctic AMR Hardware Manual Figure 5 SIM card inserted and SIM holder closed Firmware Version 1 x 14 Document Version 1 1 Hardware Manual ae ae Arctic AMR Hardware Manual 3 3 Connecting power cable A Warning If the device has already been powered wait for 5 minutes after all the LEDs have been disabled before opening the device When the device is opened connect phase and neutral cables to power connector Power connector is show in figure 6 Figure 6 Power connector Insert cable shield on top of SIM card holder see figure 7 and 8 Insert cable to device via cable gland Tighten the cable gland Note Install SIM card and cable shield before connecting power cabling A Warning Device must not be operated without cab2. The power supply can be used in 1 or 3 phase configuration Table 1 Power supply range Voltage range Phase Phase 90 440 VAC Phase N 52 254 VAC Power cable installation is described in the chapter Connecting power cable on page 15 Recommended power cabling is conductor 0 5mm to 2 5mm Firmware Version 1 x 9 Document Version 1 1 Hardware Manual b 1O LA Arctic AMR Hardware Manual Note External fuses are required for each phase line to protect the device The fuse with a rating not greater than 2A is recommended All the connections to the power connector phase and neutral must be connected via all pole safety switch 2 2 Antenna connector The device has an SMA female connector The antenna has an SMA male connector 2 3 System status LEDs The device has 5 system status LEDs When the system is fully operational all LEDS should be on Table 2 LEDs Status e Legend LED name Description CED OW POWER Device has AC power and it s operational Device SW is running OK 3 sG SIGNAL GPRS signal level is OK a NETWORK GPRS is registered GPRS is registered successfully to network to network MET METER Meter connected to device E ae and serial port is polling 2 4 Serial port The serial port connector is a 9 pin D sub female connector supporting serial speeds from 300 to 115200 bps Serial port signals and pin connections are listed in table 3 Table 3 Serial Por
3. and handling of the devices is appropriate This also applies to the maintenance of the products To prevent damage both the product and any terminal devices must always be switched OFF before connecting or disconnecting any cables It should be ascertained that different devices used have the same ground potential Before connecting any power cables the output voltage of the power supply should be checked This product is not fault tolerant and is not designed manufactured or intended for use or resale as on line control equipment or as part of such equipment in any hazardous environment requiring fail safe performance such as in the operation of nuclear facilities aircraft navigation or communication systems air traffic control direct life support machines or weapons systems in which the failure of Viola Systems manufactured hardware or software could lead directly to death personal injury or severe physical or environmental damage Firmware Version 1 x 5 Document Version 1 1 Hardware Manual UR a ae Arctic AMR Hardware Manual d Revisions Document Firmware Description of changes Version Version 12 2010 Cable shield images added Firmware Version 1 x 6 Document Version 1 1 Hardware Manual VIOLA Arctic AMR Hardware Manual Contents COPYRIGHT AND TRADEMARK c2sacsgeictventctiadencancecaneiiaaiautdantealhanceniedandeeeiennietiaamaaaraneuans 2 sid cuz e 3 DECLA
4. L SUPPORT 5ursssckvocrxsaciniensrkxEnaxaz EE avi ES Id ra F gk Ra unda veo Iul eR rad cud que az acr RS E 21 Firmware Version 1 x 7 Document Version 1 1 Hardware Manual VIOLA Arctic AMR Hardware Manual 1 Introduction Arctic AMR is an intelligent GPRS modem device for AMR connectivity The device has an integrated 1 3 phase AC power supply and GPRS connectivity Intended audience for this manual are engineers and technical staff planning and commissioning the devices to field operations 1 1 Safety Operation A Warning The device uses lethal voltages Carefully read through all the instructions in this manual and follow local safety regulations Device must not be operated when back panel is removed Voltage inside the device is extremely dangerous and may cause death or severe injury A Warning Do not touch the integrated circuits on the circuit board Static voltage discharge may damage the components Carefully read through all the instructions in this manual before installing or operating the device Firmware Version 1 x 8 Document Version 1 1 Hardware Manual VIOLA Arctic AMR Hardware Manual 2 Hardware This section describes the physical interfaces on Arctic AMR The device has four external interfaces 1 Power supply 2 Serial port RS 232 3 Antenna connector SMA 4 System status LEDs Figure 1 Physical Interface 2 1 Power supply Arctic AMR operates with external AC power
5. RATION OF GONFODBMILTY a cnatukas ax a OR KR RAA cRD 2 Flan Exc ERE is 4 WARRANTY AND SAFETY INSTRUGTIONS eeeeeeeeeeeeee ener en nnne nnne nnne 5 REVISIONS C M 6 T ANTRODUCG TON 8 1 1 Safety Operation eei intererit dese xta eta Cor EU oda us Urea bee aan ane eee 8 REI IB M 9 24 JPowersupply u node ate ee dent tad ede e bee AWA ade Ru exa in dani eade ea 9 2 2 Antenna Connector ocean Lee de aeta eta a eed EEUU e d e hn Ee eed Educ 10 2 3 System status BEDS itia il rete cited n LEE Gaede ed tok dede e eee teed 10 2 4 Serial port eee ti ese tag tas De ined A cia di Eee ded d see 10 2 5 Device identification and product label ssssssseeseeeennens 11 3 INSTALLING THE DEVIGE x cuire ve pie gepil phuc tadaBasxa bdducs si Ead bee tvdds ud pioi idus 12 3 4 Unpacking the devie ceseroun nene eere nee nei Ra euet Ene e 12 3 2 Installing SIM Card eie aiiim teft Lie uat edet oa aec edie ede 12 3 3 Connecting power cable sssssssssssesssssseeeneene nennen nnne ensi nrnr rennen nene 15 3 4 Mounting the back panele cancere a A nn nnn nnns nete 17 3 5 Mountng the device iere Pee ice a Eie n EE c RR ERE a Ex nd 18 4 SPECIFICA TIONS usiustciten tinidudexs kata e rubi boda vidua etu tu aA 19 BU P NERRU Ig 20 5 TECHNICA
6. VIOLA sy stems Arctic AMR Hardware Manual Arctic AMR Hardware Manual 2170 Firmware Version 1 x Document Version 1 1 December 2010 Hardware Manual VIOLA Arctic AMR Hardware Manual Copyright and Trademark Copyright 2008 2010 Viola Systems Ltd All rights to this manual are owned solely by Viola Systems Ltd referred elsewhere in this User s Manual as Viola Systems All rights reserved No part of this manual may be transmitted or reproduced in any form or by any means without a prior written permission from Viola Systems Ethernet is a trademark of XEROX Corporation Windows and Internet Explorer are trademarks of Microsoft Corporation Netscape is a trademark of Netscape Communications Corporation All other product names mentioned in this manual are the property of their respective owners whose rights regarding the trademarks are acknowledged Viola Systems Ltd Lemmink isenkatu 14 18 A FI 20520 Turku Finland E mail info violasystems com Technical Support Phone 358 20 1226 226 Fax 358 20 1226 220 E mail support violasystems com Internet http www violasystems com Firmware Version 1 x 2 Document Version 1 1 Hardware Manual VIOLA Arctic AMR Hardware Manual Disclaimer Viola Systems reserves the right to change the technical specifications or functions of its products or to discontinue the manufacture of any of its products or to discontinue the support of any of it
7. le shield and cable clamp securely connected Firmware Version 1 x 15 Document Version 1 1 Hardware Manual VIOLA Arctic AMR Hardware Manual Table 4 Power connector Figure 7 Cable Tightening Securely tighten cables to the power connector as shown in figure 7 Figure 8 Cable Gland Firmware Version 1 x 16 Document Version 1 1 Hardware Manual M 10 LAW Arctic AMR Hardware Manual j Note Cable gland must be securely connected to prevent cable damage 3 4 Mounting the back panel Insert the device back panel and tighten torx screws on bottom of the device 4 pcs torx T10 Figure 9 Mounting the device Firmware Version 1 x 17 Document Version 1 1 Hardware Manual M 10 LAW Arctic AMR Hardware Manual i Cable gland e Cable gland plug B fomos Cable shield Back panel A Warning The device uses lethal voltages Device must not be operated before back panel is mounted and securely tightened with torx figure 8 3 5 Mounting the device Arctic AMR device can be mounted by using the mounting holes in the back panel With these holes the device can be mounted on a flat surface for example a cabinet If DIN rail mounting 35 mm is needed an optional DIN rail mounting kit product code 3003 can be mounted to the side panel Figure 10 Optional DIN rail mounting installed Firmware Version 1 x 18 Document Version 1 1 Hardware Manual VIOLA Arctic AMR Hardwa
8. me Serial no Note the status of your Arctic in the space below before contacting technical support Include information about error messages diagnostic test results and problems with specific applications Firmware Version 1 x 21 Document Version 1 1
9. obligation to you under this warranty IN NO EVENT SHALL VIOLA SYSTEMS BE LIABLE FOR INDIRECT INCIDENTAL CONSEQUENTIAL OR SPECIAL DAMAGES OR LOSSES INCLUDING LOSS OF DATA USE OR PROFITS EVEN IF VIOLA SYSTEMS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES In no event shall Viola Systems liability exceed the original purchase price of the device server Some states or countries do not allow the exclusion or limitation of incidental or consequential damages so the above limitation or exclusion may not apply to you Obtaining Warranty Service You must notify Viola Systems within the warranty period to receive warranty service During the warranty period Viola Systems will repair or replace at its option any defective products or parts at no additional charge provided that the product is returned shipping prepaid to Viola Systems All replaced parts and products become the property of Viola Systems Before returning any product for repair customers are required to contact the Viola Systems Firmware Version 1 x 20 Document Version 1 1 Hardware Manual VIOLA Arctic AMR Hardware Manual 6 Technical Support Contacting Technical Support Phone 358 20 1226 226 Fax 358 20 1226 220 E mail support violasystems com Internet http www violasystems com Recording Arctic Information Before contacting our Technical Support staff please record if possible the following information about your Arctic product Product na
10. re Manual 4 Specifications Table 5 Specifications GSM GPRS Frequency band Quad band 800 900 1800 and 1900 MHz Firmware Version 1 x 19 Document Version 1 1 Hardware Manual VIOLA Arctic AMR Hardware Manual 5 Limited Warranty Coverage Viola Systems warrants this hardware product to be free from defects in materials and workmanship for the warranty period This non transferable limited warranty is only to you the first end user purchaser The warranty begins on the date of purchase and lasts for the period specified below Arctic AMR one 1 year Excluded Products and Problems This warranty does not apply to a Viola Systems software products b expendable components such as cables and connectors or c third party products hardware or software supplied with the warranted product Viola Systems makes no warranty of any kind on such products which if included are provided AS IS Excluded is damage caused by accident misuse abuse unusually heavy use or external environmental causes Remedies Your sole and exclusive remedy for a covered defect is repair or replacement of the defective product at Viola Systems sole option and expense and Viola Systems may use new or refurbished parts or products to do so If Viola Systems is unable to repair or replace a defective product your alternate exclusive remedy shall be a refund of the original purchase price The above is Viola Systems entire
11. s products without any written announcement and urges its customers to ensure that the information at their disposal is valid Viola software and programs are delivered as is The manufacturer does not grant any kind of warranty including guarantees on suitability and applicability to acertain application Under no circumstance is the manufacturer or the developer of a program responsible for any damage possibly caused by the use of a program The names of the programs as well as all copyrights relating to the programs are the sole property of Viola Systems Any transfer licensing to a third party leasing renting transportation copying editing translating modifying into another programming language or reverse engineering for any intent is forbidden without the written consent of Viola Systems Viola Systems has attempted to verify that the information in this manual is correct with regard to the state of products and software on the publication date of the manual We assume no responsibility for possible errors which may appear in this manual Information in this manual may change without prior notice from Viola Systems Firmware Version 1 x 3 Document Version 1 1 Hardware Manual VIOLA Arctic AMR Hardware Manual Declaration of Conformity according to ISO IEC Guide 22 and EN 45014 Manufacturer s Name Viola Systems Ltd Manufacturer s Address Lemmink isenkatu 14 18 A Fl 20520 Turku Finland declares that this produc
12. t Product Name Arctic AMR conforms to the following standards EMC EN 55022 Emission Test Class A 1 Radiated Emissions 30 1000MHz 2 Conducted Emissions 0 15 30MHz EN 50082 1 Immunity Test 1 IEC 801 3 Radio Frequency Electromagnetic Field 2 IEC 801 2 Electrostatic Discharge 3 IEC 801 4 Fast Transients AC Power Ports and Signal cables Supplementary Information The product complies with the requirements of the Low Voltage Directive 73 23 EEC and EMC directive 89 336 EEC N Warning This is a Class A product In a domestic environment this product may cause radio Interference which may make it necessary for the user to take adequate measures Manufacturer s Contact Information Viola Systems Ltd Lemmink isenkatu 14 18 A FI 20520 Turku Finland Phone 358 20 1226 226 Fax 358 20 1226 220 Firmware Version 1 x 4 Document Version 1 1 Hardware Manual VIOLA Arctic AMR Hardware Manual Warranty and Safety Instructions Read these safety instructions carefully before using the products mentioned in this manual Warranty will be void if the product is used in any way in contradiction with the instructions given in this manual or if the product has been tampered with The devices mentioned in this manual are to be used only according to the instructions described in this manual Faultless and safe operation of the devices can be guaranteed only if the transport storage operation
13. t Pin Connection Number Name Explanation Spem qu Ho es omms Harem B a 7000 Firmware Version 1 x 10 Document Version 1 1 Hardware Manual VIOLA Arctic AMR Hardware Manual 2 5 Device identification and product label The device can be identified on product label The device has a unique serial number as shown in the figure 2 Figure 2 Unique serial number Viola Systems CE EAR B C1025 0090 ps MCADOO A Firmware Version 1 x 11 Document Version 1 1 Hardware Manual VIOLA Arctic AMR Hardware Manual 3 Installing the device A This chapter describes the safe installation of the device Warning The device uses lethal voltages Device must not be operated when the back panel is removed Voltage inside the device is extremely dangerous and may cause death or severe injury 3 1 Unpacking the device Arctic AMR is delivered in a bulk package containing the device itself antenna cable clamp cable shield and torx screws for back panel mounting If any of the items are missing or are damaged please contact Viola Systems Ltd All packaging materials are recyclable Viola Systems urges its customers to follow environmental regulations regarding the disposal of all materials 3 2 Installing SIM card AN For GPRS connectivity SIM card must be installed to the device SIM card installation is done using torx T10 To open the device open the screws on bottom of the device 4 pcs Warning
Download Pdf Manuals
Related Search