MODEL : LK-TE200 Series
Contents
1. SEWOO TECH CO LTD 28 6 Gajangsaneopdong ro Osan si Gyeongi do 447 210 Korea TEL 82 31 459 8200 FAX 82 31 459 8880 www miniprinter com TE200 Series Rev B 8 12 MODEL LK TE200 Series Receipt Printer User s Manual All specifications are subject to change without notice Disposal of Old Electrical amp Electronic Equipment Applicable in the European Union and other European countries with separate collection systems This symbol on the product or on its packaging indicates that this product shall not be treated as household waste Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronics equipment For more detailed information about recycling of this product please contact your local city office your household waste HEE clisposal service or the shop where you purchased the product Table of Contents 1 Parts Identifications 3 2 Setting up the printer 4 2 1 Unpacking 4 2 2 Connecting the cables 5 2 3 Loading the roll paper 9 2 4 Adjustment of paper width 12 3 Control panel and other functions 13 3 1 Control panel 13 3 2 Error Indicating 13 4 Self Test 14 5 ASCII Print 15 6 Select Baudrate Mode 15 7 Hexadecimal Dump 16 8 Printer cleaning 17 9 Specifications 18 9 1 General Specifications 18 9 2 Auto Cutter Specifications 20 9 3 Interface 20 9 4 Electrical Charac2. DESCRIPTION 1 5V 5V 2 DATA Printer transmit data line 3 DATA Printer transmit data line 4 GND System Ground Serial Interface PIN SIGNAL 1 0 DESCRIPTION 2 TxD Output Printer transmit data line RS 232C level RxD Input Printer receive data line RS 232C level 4 20 DTR Output Printer handshake to host line RS 232C level 6 DSR Input Data Send Ready 1 7 GND System Ground 2 2 2 Cash Drawer Connector The printer can operate two cash drawers with a 6 pin RJ 11 modular connector The driver is capable of supplying a maximum current of 0 1A for 510ms or less when not printing HE PIN SIGNAL DESCRIPTION 1 Signal GND 2 Drawer kick out drive signal 1 Output 3 Drawer open close signal Input 4 24V 5 Drawer kick out drive signal 2 Output 6 Signal GND 2 3 Loading the Roll Paper Notes Be sure to use paper rolls that meet the specifications Do not use paper rolls that have the paper glued to the core because the printer cannot detect the paper end correctly Turn off power switch 1 Make sure that the printer is not receiving data Otherwise data may be lost 2 Open the paper roll cover by pushing down the cover open button 3 Remove the used paper roll core if there is one inside 4 Insert new paper roll as shown 5 Be sure to note the correct direction that the paper comes off the roll amp CAUTION When the paper is jamm
3. FS q Define NV bit image 44 GS Select character size 45 GS Set absolute vertical print position in page mode 46 GS Define downloaded bit image 47 GS Print downloaded bit image 48 GS B Turn white black reverse printing mode on off 49 GS H Select printing position of HRI characters 50 GS Transmit printer ID 51 GSL Set left margin 52 GSP Set horizontal and vertical motion units 53 GSV Select cut mode and cut paper 54 GSW Set printing area width 55 GS Set relative vertical print position in page mode 56 GSa Enable disable Automatic Status Back ASB 57 GS f Select font for HRI characters 58 GSh Set bar code height 59 GS k Print bar code 60 GSr Transmit status 61 GS v0 Print raster bit image 62 GS w Set bar code width lt Add gt 1 ESC i Full cut 2 ESC m Partial cut 3 FS Set print mode s for Kanji characters 4 FS amp Select Kanji character mode 5 FS Turn underline mode on off for Kanji character 6 FS Cancel Kanji character mode 7 FS 2 c1 d1 dk_ Define user defined Kanji characters 8 FSC Select Kanji character code system 9 FSS12 Set Kanji character spacing 10 FSW Turn quadruple size mode on off for Kanji character No Command Function REMARKS 1 HT Horizontal tab 2 LF Print and line feed 3 CR Print and carriage return 4 FF Print and return to standard mode in page mode 5 CAN Cancel print data in page mode 6 DLE EOT Real time status transmission 7 DLE ENQ Real time request to print
4. ed with cutter the top cover might be stuck In this case repeat power on and off several times If the top cover is still stuck please follow the steps to release the papers from jamming 1 Make sure the printer is turned off 2 Take out DIP switch cover as shown 6 Pull out a small amount of paper as shown Then close the cover 7 Tear off the paper as shown 10 11 2 4 Adjustment of paper width 1 Please adjust the Paper Guide to fit to the paper width as the direction of arrow 3 Pull the edge of paper once the paper roll is installed correctly and close the Paper Cover 12 3 Control panel and other functions 3 1 Control panel You can control the basic paper feeding operations of the printer with the button on the control panel The indicator lights help you to monitor the printers status Control Panel POWER QO ERROR Q PAPER FEED Button The button can be disabled by the ESC c 5 command Press the FEED button once to advance paper one line You can also hold down the FEED button to feed paper continuously 3 2 Error indicators This section explains the different patterns signaled by the three LED indicators located on the top cover of the printer PAPER ERROR POWER STATUS REMARKS RED RED GREEN Power off OFF OFF OFF Normal power is not supplied to the pri
5. er 8 DLE DC4 Generate pulse at real time 9 ESC FF Print data in page mode 10 ESC SP Set right side character spacing 11 ESC Select print mode s 12 ESC Set absolute print position 13 ESC Select cancel user defined character set 14 ESC amp Define user defined characters 15 ESC Set bit image mode 16 ESC Turn underline mode on off 17 ESC 2 Select default line spacing 18 ESC 3 Set line spacing 19 ESC Select peripheral device 20 ESC Cancel user defined characters 21 ESC Initialize printer 22 ESC D Set horizontal tab positions 23 ESCE Turn emphasized mode on off 24 ESC G Turn double strike mode on off 25 ESC J Print and feed paper using minimum units 26 ESCL Select page mode 27 ESC M Select character font 28 ESC R Select an international character set 29 ESC S Select standard mode 30 ESC T Select print direction in page mode 31 ESC V Turn 90 clockwise rotation mode on off 32 ESC W Set printing area in page mode 33 ESC Set relative print position 34 ESCa Select justification 35 ESC c3 Select paper sensor s to output paper end signals 36 ESC c 4 Select paper sensor s to stop printing 37 ESC c5 Enable disable panel buttons 38 ESCd Print and feed paper n lines 39 ESC p General pulse No No 23
6. erheating continuous operation of the printer should be 1 5 m or less in print length Set the pause time for 30 seconds or more than it 17 Appendix A Specifications 8 Overall dimension 9 1 General Specifications 1 Printing Method Direct line thermal printing 2 Print speed 160mm sec 200mm sec 300mm sec 3 Dot density 180 DPI Hor Ver 180 180 0 142mm 0 142mm dot 4 Printing Width 180 DPI Max 72mm 512 dots 5 Number of print columns No of columns 180 DPI 42 56 6 Roll paper Refer to chapter 2 for details on the recommended roll Paper Paper width 50mm 82 5mm Roll diameter Max 80mm 7 Weight 3 75 Ibs 1 7Kg 9 2 Auto Cutter Specifications 1 Cutting Frequency Max 30 cuts per minute 2 Thickness of paper 0 06 0 09 mm 3 Cutter Life 1 5 million cuttings 9 3 Interface RS232 Serial Interface Centronics Parallel Interface IEEE1284 USB Interface Ethernet Interface 100Mbps 9 4 Electrical Characteristics 1 Input Voltage DC 24V 10 2 Current Consumption Operating Approx 1 5 A at ASC printing Peak Approx 10 A at print duty 100 For 10 seconds or less Stand by Approx 0 03 A 3 Power Connector PINS GROUND PIN1 24V DC PIN2 No CONNECTION 20 amp Important When connecting or disconnect
7. ing the power supply from the printer be sure that the following cautions are observed 1 Use a power supply Limited Power Supply of DC 24V 10 and more than 1 75A 2 Be careful about installing the printer in an area where there is noise 3 Take the appropriate measure to protect against electrostatic AC line noise etc 9 5 Environmental Requirements 1 Operating Temperature 5 C to 40 C Humidity 10 to 90 RH without condensation 2 Transport Storage except paper Temperature 20 C to 60 C Humidity 10 to 90 RH without condensation 9 6 Reliability 1 MCBF 60 million lines based on an average printing rate of 12 5 with paper thickness in the range of from 65ym 75um 35 million lines based on an average printing rate of 12 5 with paper thickness in the range of from 76pm 150m 2 Head Life 160Km 3 Cutter Life 1 500 000 cuts 9 7 Certification 1 FCC PART15 CLASS A 2 UL cUL UL 60950 1 CE EMCD CE EMCD Class B should use Parallel shield Cable complied with IEEE 1284 standards 5 ENERGY STAR 21 10 Command List No Command Function REMARKS 40 ESC t Select character code table 41 ESC Turn upside down printing mode on off 42 FS p Print NV bit image 43
8. inter is on a telephone Before connecting any of the cables make sure that both the printer and the computer are turned off 2 2 1 Interface Connector 14 oo0oo0o000000000 ooo0oo0o000 00000 j 1 lt D SUB 25 Female Serial gt 13 eS lt Centronics Parallel gt Link END Status END Centronics Parallel Interface PIN SIGNAL 1 0 DESCRIPTION 1 STROBE Input Synchronize signal Data received 2 9 DATAO 7 Input Output Data bit Transmitted 0 7 10 ACK Output Data receiving completed 11 BUSY Output Impossible to print of data receiving 12 PE Output Paper empty 13 SELECT Output Printer status for ON OFF line 14 AUTO FEED Input Paper auto feed signal 15 GROUND System ground 16 GROUND System ground 17 NC a 18 LOGIC H 3 3V 19 30 GROUND System ground 31 INIT Input Initialize 32 ERROR Output Printer error 33 GROUND System ground 34 NC 35 NC d 36 SELLECT IN Input Printer select signal Ethernet Interface PIN SIGNAL 1 0 1 Data Out Output Data 2 Data Out Output Data 3 GND Ground 4 Data IN Input Data 5 Data IN Input Data 6 N C 7 N C 8 N C 87654321 lt USB B Type gt lt Ethernet gt USB Interface PIN SIGNAL 1 0
9. ms a cutting when exiting this mode 4 The printer is ready to receive data after finishing setting 14 5 ASCII Print ASCII PRINT is printing a test page constructed ASCII code You can able to check the printer works properly with this The ASCII PRINT test automatically ends and cuts the paper after printing the following Completed The printer is ready to receive data as soon as it completes the ASCII PRINT 6 Select Baudrate Mode After entering the BAUDRATE MODE the list which can select the BPS will be printed Similar like Self Test you can press the FEED button to select a BAUDRATE Once the input performs properly the printer shows a result and store The printer is ready to receive data as soon as it completes the SELECT BAUDRATEMODE SELECT BAUDRATE BY BUTTON 1 9600bps 2 19200bps 3 38400bps 4 115200bps 15 7 Hexadecimal Dump This feature allows experienced users to see exactly what data is coming to the printer This can be useful in finding software problems When you go into the hex dump function the printer prints all commands and other data in hexadecimal format along with a guide section to help you find specific commands To use the hex dump feature follow these steps 1 Please turn printer off 2 Please turn printer on while press down Feed button 3 Press the FEED button three times when the Self Test printed 4 Now printer had entered into Hexa dump mode 5 Run any s
10. nter Poweron OFF OFF ON Normal power is supplied to the printer On line OFF OFF ON Normal error free mode Cover open OFF ON ON Close cover Paper empty OFF ON ON Insert new paper roll Paper near end ON OFF ON Paper is low Test mode OFF OFF ON Ignored error led 13 4 Self Test The self test result indicated whether the printer is operating properly Also with this user can check following options or status of the printer Control circuit Printer mechanism Printing quality ROM version Interface setting This test is independent of any other equipment or software Running the self test 1 Make sure the printer is turned off and the printer cover is closed properly before performing the self test 2 Turn the printer on holding the FEED button then the self test will start The self test prints the printer setting value and then prints the following and pauses Error LED On SELECT MODE BY BUTTON 1 ASCII PRINT 2 SELECT BAUDRATE MODE 3 HEXADUMP MODE 3 Press the FEED button consecutively 1 3 1 ASCII PRINT press the FEED button once 2 SELECT BAUDRATE MODE press the FEED button twice 3 HEXADUMP MODE press the FEED button triple time Printing test page constructed with ACII code Set the speed of Serial Interface You can set the BAUDRATE in this mode Printing the HEX value received from the interface Wait for 5 6 seconds if you want to exit Printer perfor
11. oftware program that sends data to the printer The printer prints Hexadecimal printing mode and then all the codes it receives in a two column format The first column contains the hecadecimal codes and the second column gives the ASCII characters that correspond to the codes Hecadecimal Dump 1B 21 00 1B 2602 40 40 amp 1B 25 01 1B 63 34001B c4 41 42 43 44 45 46 47 48 ABCDEFGH A period is printed for each code that has no ASCII equivalent 6 Turn off the printer 7 Turn on the printer 16 8 Printer cleaning If the interior of the printer is dusty printing quality can be lowered In this case follow the instructions below to clean the printer Note 1 Make sure to turn the printer power off prior to cleaning 2 Regarding print head cleaning as the print head is very hot during printing turn off the printer power and wait approximately 10 minute before start 3 When cleaning the print head take care not to touch the heated part of the print head The print head subject to be damaged by static electricity 4 Take care not to allow the print head to become scratched and or damaged in any way 1 Use an applicator swab moistened with an alcohol solution to clean the print head and remove any dusts 2 Once the cleaning is completed insert paper roll into the printer few minutes later and close the printer cover amp amp Preventing Overheating To prevent the motor from ov
12. teristics 20 9 5 Environmental Requirements 21 9 6 Reliability 21 9 7 Certification 21 10 Command List 22 1 Parts Identifications CONTROL PANEL Features LED indicators to indicate printer status and switches to operate the printer PRINTER COVER Open this cover to load or replace paper COVER OPEN LEVER Pull down this lever to open the printer cover POWER SWITCH Used to turn on off power to the printer INTERFACE CONNECTOR INTERFACE CONNECTOR USB PERIPHERAL DRIVE CONNECTOR POWER CONNECTOR 2 Setting Up the Printer 2 1 Unpacking Your printer box should include these items If any items are damaged or missing please contact your dealer for assistance The Printer User s Manual Roll Paper Interface Cable optional Adaptor Optional 2 2 Connecting the Cables You can connect up the cables required for printing to the printer They all connect to the connector panel on the back of the printer which is shown below ee INTERFACE CONNECTOR USB POWER CONNECTOR a o aa For connection to a For connection of host computer host computer PERIPHERAL DRIVE CONNECTOR the AC adapter Connects to peripheral units Never unplug the such as cash drawers etc AC adapter while Do not connect this to the pr
Download Pdf Manuals
Related Search