FunkyHeat Touschreen User Manual
Contents
1. Right below a power socket In contact with the floor In close proximity to flammable or combustible materials or pressurised containers Make sure that there are no electrical cables or pipes in the wall which could be damaged during installation Funayteat 3 1 Wall mounting Make sure the plugs and screws provided are suitable for the wall type onto which the appliance is going to be mounted If in doubt ask professional qualified personnel IMPORTANT It is recommended to secure the appliance only with the A screws on the upper shelves Leave the lower screws slightly loosened so as to allow the expansion of the panel when heating X X A Funiydeal 3 2 Electrical connection If hardwiring to a fused spur this work must be done by a qualified electrician The electrical connection must be carried out in compliance with the national regulations for electricians in force Before connecting the appliance to the electrical network make sure that the power is off Do not install the appliance if e The power supply cable is damaged e The appliance and the control boxes are damaged The appliance supply voltage is 230V 50Hz Make sure the power supply complies with the appliance s voltage Make sure that the power supply cable never comes into contact with the hot surface of the appliance The power supply must be equipped with an omni pola2. Minus ELi Li key Together key Together Zz nmm PE EN for 3sec E ereemremecel for 3sec gt gt K K A MOOTO OUTO 1i O i A f ON Non nm N Y LY ILY Ly VY WY H y LYI L y LA 1m Funkydeal IR transmission If no button is in operation after 1 second the remote control will transmit the IR data to the device and the IR transmission symbol will start flashing At the end of data transmission the symbol will disappear Fig 8 Night mode transmission Night mode finished Comfort mode Night mode IR date transmission IR data Ihe Ine Inne Ihe of f _ inn Ie f lt i i E Hh Press E ht After GUL E Uh i Hode key 12 soc E pam g p tle Kf p p p na Ei Mt a ne eee i Ta T P A f l j i i TOTTI TATA PIO OT rO OTO nf for i 1E N ni in f fy Wf Non fi N NN wA nn p SUI IS U CPU YY yy Low Batteries When the batteries tension is lower than 2 2 V the Batt symbol will be displayed for 3 seconds every minute in the clock zone The user will have to replace the batteries Fig 9 6 Cleaning and maintenance Before starting any operation make sure that the equipment is completely cold and that it is disconnected from the mains To clean use a soft damp cloth with mild detergent to clean the crystals Do not use abrasive cleaners or corrosive solvents In case of technical problems contact a qualified profession
3. kit Instruction manual Read these instructions carefully before installing and using the appliance Keep them for all future reference Use the appliance only according to these instructions These instructions however do not cover all situations that may arise Use caution and common sense when installing and using the appliance It is forbidden to modify in any way the features of the appliance or to disconnect fixed parts Make sure that the appliance is in good condition Do not use the appliance if damaged Contact the retailer or professional qualified personnel The materials used for packaging can be recycled For disposal use dedicated recycling containers Funky at 3 Positioning and installation This appliance is intended for domestic use for room heating It shall not be put to any other use It must be fixed onto a wall as indicated in this instruction manual In case of vertical positioning the control graphics must be kept on the right hand side while for horizontal positioning the control graphics must be kept on the lower side In the bathroom or shower the appliance must be fitted in the correct zone for the IP24 rating The control devices must be out of reach for people in the bathroom of shower The controls must be placed in zone 3 Fig 1 Keep the given minimum distances fig 2 3 ZONE 2 ZONE 3 CONTROL PANEL Funkyteat Do not install the appliance
4. wire sO Comfort The temperature of the appliance is controlled by the Comfort mode settings C Night The temperature of the appliance is controlled by the Night mode settings DA 2hr The appliance heats up the room at maximum power timer Clock The temperature of the appliance is controlled by the mode of either the comfort or night programs ly Stand by The appliance is not in operation 6 Lock Locks the keypad of the appliance F uty aT Switching Modes See Fig 1 below 1 Once the batteries are installed the LCD display will be showing all symbols for three seconds After this go to the Date and time settings interface the date will be flashing the user will then be able to set the date by using the Plus or Minus buttons Press then the Mode button the Hour will be flashing set current hour by using the Plus or Minus buttons Then press the Mode button once again the minutes section will be flashing set current minute by using the Plus or Minus buttons once again Press the Mode button again to terminate the Minutes setting and to switch to stand by mode While Date is flashing if the user does not wish to set any parameter just press the Stand by button to switch to stand by mode immediately Fig 1 Power on Setting da
5. INSTRUCTION MANUAL Funkyheat SMART EFFICIENT HEATING TOUCHSCREEN FAR INFRARED HEATER Sold amp Distributed in the UK amp Ireland by Funkyheat Ltd The Carlile Institute Huddersfield Road Meltham HD9 4AE www funkyheat co uk This appliance complies with European Directives 2004 108 EC on electromagnetic compatibility C 2006 95 EC on low voltage 2002 95 EC_ on the restrictions of the use of certain hazardous substances Funkyheal CONTENTS 1 Technical features of the appliance 3 2 General Information 4 3 Positioning and installation 5 3 1 Wall mounting 7 3 2 Electrical connection 8 4 Warnings 9 4 1 Control panel touch screen 10 5 Remote Control 12 6 Cleaning and maintenance 18 7 Quick Controller Set Up 19 Funkyheal 1 Technical features of the appliance 230V 50Hz Class H Degree of protection IP24 The features of the appliance are indicated on the features label situated on the rear edge of the cover xxxx EWE Cat TYPE Model IP24 230V 50Hz W C o XXXX Manufacturer s trademark or brand 12345678 serial No Category type model Degree of protection Voltage Power EC Marking double insulation quality label Funkyeat 2 General Information Unpack the appliance and place it either on the polystyrene protection or on a carpet Package contains Appliance Remote control Wall mounting
6. al Furkybeat 7 Quick Controller Set Up 1 Take the batteries out to re set it 2 Put the batteries in 3 The display will flash 00 00 with the number 1 in the top right 4 Press the centre oval button twice this allows you to set the clock Use the or buttons above and below the oval button to set the time 5 Press the clock icon button on the top left the 1 in the display on the right will now flash you need to decide which is day one for you so that you can differentiate the weekend settings 6 Press the oval button twice to go through the hours and minutes The small block above the numbers in the display with now flash This is how you set when the heater comes on or stays off 7 Press for all the time you want the heater off When you reach the time that you want the heater to come on and stay on press When you want it off again press 8 When you reach the end of the day press the centre oval button again this will take you to the next day number 2 do this for all 7 days 9 Now use the button on the bottom right to switch on the heater 10 You will now see the sun icon This is the temperature that the heater will be trying to heat to when the heater is on The default is 20 C you can change this with the or buttons 11 Press the centre oval button again You will now see the moon icon This is the temperature that the heater will Keep the space at when the the heater is off The d
7. ct the unit calibrate it or do cleaning and maintenance Children must not play with the appliance The appliance was designed for the heating of domestic premises During normal operation the surface of the appliance may reach high temperatures which can cause burns Combustible or flammable materials and pressurised containers sprays fire extinguishers etc must be kept at a distance of at least 50cm from the appliance Do not touch the appliance with wet hands or feet The appliance must not be used if the crystal glass is damaged It is important not to cover the appliance at any time in order to avoid dangerous overheating Fig 6 Fig 6 Furdyeat 4 1 Control panel touch screen Control panel with symbols and functions Fig 7 T1 T2 T3 T4 T5 T6 L7 L8 S1 STAND DY ee ene meen nen ene eee L1 Low temperature heating 50 C cceeeee sees Medium temperature heating 70 C Maximum temperature heating 90 c Maximum temperature 2 hours boost 0088 Keypad LOCK sescsictiacsiasaasacatnusenungonntorinatsensiennacteaeans Red LED indicates radiator is heating up Appliance is heating Infrared sensor for remote control Eliz P ki EP Sal T2 EP T3 i L406 a T4 Cel L560 TS L6 o E L2 L3 L4 L5 L6 Furkyeat These far infrared heaters are equipped with an advanced control system with touch
8. e the temperature will drop by 0 5 degrees Temperature can be adjusted from 7 up to 32 degrees 2 The Night mode temperature setting can not be higher than the Comfort mode s one Example If the Comfort mode s temperature has been set to 25 degrees when switching to Night mode and wanting to set the temperature once it reaches 25 degrees the temperature will not rise even when pressing the Plus button Antifreeze Mode see Fig 1 Go to Antifreeze mode the temperature is fixed to 7 degrees by pressing the Plus or Minus buttons the temperature cannot be neither risen nor reduced Clock Mode see Fig 1 Go to Clock mode the LCD display will be showing temperature date time and state of the daily program Pilot Wire Mode see Fig 1 Go to Pilot Wire mode the device will recognise the commands received from the Pilot Wire Comfort Nigh Antifreeze ECO Stand by 2 Hours Mode In any mode by pressing the two hours button the device will start to heat up the environment at full power for 2 hours By pressing the button again the remote control will go back to the previous mode Fig 2 Comfort mode 2 hour mode Comfort mode A OA AT MOA Press 2 Pisas 2 hour LT hour key r key r 7 N f f fy y If Funkyheat Stand by Mode In any mode by pressing the Stand by button the remote control will go into stand by mode and
9. efault setting is 18 C we generally reduce this to 14 C or 15 C 12 Press the centre oval button again You will now see the snowflake icon This is the frost protection setting Put it on this setting if you are on holiday and it will stop the space from dropping below this temperature 13 Press the centre oval button again You will now see the timer clock icon These are the settings you programmed in earlier and the heater will now operate on these programmed settings Now when you press the centre button and point it Funayeat at the heater you will notice that the heater will beep this is the heater and the controller communicating Work through the icons until you get to the timer icon point it at the heater as you press and wait It is now set up 14 Finally using the touchscreen on the heater press the II or III this controls the surface temperature of the heater Initially select III 15 You should now have 3 green lights showing on the heater The first above the Ill the second above the wi fi signal and the third below the branding icon You will also note a red light coming sometimes this is the heater and the controller communicating and activating the heater as required Funayteat Funkyheat SMART EFFICIENT HEATING Sold amp Distributed in the UK amp Ireland by Funkyheat Ltd The Carlile Institute Huddersfield Road Meltham HD9 4AE www funkyheat co uk Funkydeal
10. r cut off device with a gap between contacts of at least 3 mm including the pilot wire if present If the appliance is mounted in the bathroom or shower the power line including the pilot wire must be equipped with a high sensitivity differential protection with maximum rated current of 30mA In humid environments bathrooms kitchens laundry rooms etc it is very important that the electrical connection to the network is situated at least at 25 cm from the floor PHASE BROWN PHASE Electrical mains NEUTRAL GREY F oO NEUTRAL PILOTE WIRE BLACK gt r_ Cable of applance THO POSSIBLE CASES 1 istallation Connect the two with pilot wire pilot wires 2 istallation connect the pilot wire to the drive box without pilot wire or to the planning central Funkyte at 4 Warnings This appliance is not intended for use by persons including children with reduced physical sensory or mental capabilities Children under 3 years of age must be kept away from the appliance and always be supervised The appliance can be used by children aged between 3 and 8 and by people with reduced physical sensory or mental capabilities or with lack of experience or necessary knowledge as long as they are being supervised and or after they have received appropriate instructions for a safe use of the appliance and for an understanding of its inherent dangers They shall not disconnect or conne
11. screen controls and light indicators which indicate the set function Changes in settings are also notified by a beep When connecting the power supply all the LEDs light up for 2 seconds and you will hear a long beep After this only L1 and L8 will remain on Touch T2 if you wish to heat up the room with a low surface temperature on the heater The L2 and L7 green LEDs will light up and you will hear a beep When the surface of the radiator reaches the set temperature L7 switches on and off cyclically in order to maintain the set temperature Touch T3 if you wish to heat up the room with a medium surface temperature on the heater The L3 and L7 green LEDs will light up and you will hear a beep When the surface of the radiator reaches the set temperature L7 switches on and off cyclically in order to maintain the set temperature Touch T4 if you wish to heat up the room with a maximum surface temperature on the heater The L4 and L7 green LED will light up and you will hear a beep When the surface of the radiator reaches the set temperature L7 switches on and off cyclically in order to maintain the desired temperature Touch the T5 button if you wish to have the maximum surface temperature for a limited time 2 hours the L5 and L7 LEDs will light up The radiator will operate at maximum temperature for 2 hours after which it will go back to operate in the function set before the Boost function lf after
12. the device will stop operating By pressing this button again the remote control will go back to the previous mode Fig 3 Comlort mode Stand by mode Comfort mode A Tiana A Pen Eco Mode Eco mode can be activated to reduce power consumption when the room is empty for a specific period of time By pressing the Eco button the remote control display will show the icon of the function By pressing the Eco button again the function will be disabled and the icon will disappear Window open Mode Pressing the Eco and buttons simultaneously for 3 seconds will activate the window open sensor Pressing the Eco and buttons again simultaneously for 3 seconds will disable the function Presence Radar Mode Pressing the Eco and buttons simultaneously for 3 seconds will activate the sensor of presence in the room Pressing the button Eco and buttons again simultaneously for 3 seconds will disable the function Time and program setting 1 By pressing the Mode button the hour section will start flashing and the user will be able to set the current hour by using the Plus or Minus buttons By pressing the Mode button again the minutes section will start flashing and the user will be able to set the minutes by using the Plus or Minus buttons Funayheat 2 When the Minutes section is flashing by pressing the Mode button the user may proceed to set the Monday program and the 0
13. the settings you wish to lock the keypad press the T6 button for 5 seconds you will hear 4 beeps confirming the setting When touching the other buttons lightly the L6 LED will flash for 2 3 seconds indicating the keypad is currently locked Only the T1 button will remain operational so to put the appliance on stand by at any time To reactivate the keypad press the T6 button for 5 seconds 4 consecutive beeps will confirm the setting Funkybeat Rem ntrol These far infrared heaters are equipped with infrared remote control allowing you to set through the S1 sensor the control of room temperature and to set different operating programs When the S1 sensor receives the information the L8 LED flashes to indicate the communication has been received It will then stay lit to indicate that the appliance has been programmed For an efficient communication point the remote control at the receiver unit The distance between the remote and the receiver must not be greater than 7 m 1 Double infrared communication one at the top and one at the bottom of the remote control 2 Seven push buttons 3 4 Two AAA LRO3 1 5 V batteries Maximum communication distance from device 7 m ELE Cx et ee amp OCERO sy Tie nia Funiyneat oh 2 4 6 8 1 B14 16 18 20 22 24 a 1 Symbol Mode Function Description Fil pilot The temperature of the appliance is controlled by the pilot
14. time point will start flashing The user may then use the Plus or Minus buttons to set the Comfort temperature or Night temperature to current time by pressing Plus the point indicating that at the current time the Comfort temperature mode will be activated While by pressing the Minus button the point will disappear to indicate that at current time the Night temperature mode will be activated Subsequently the point of the following hour will flash in the same way for the setting By pressing the Mode button again the subsequent day will be displayed and the user will be able to set in the same way the modes for the hours from 0 to 23 ig ene a SSSSSSSSSSOOCOSS caooo RAINS NR rt RELA ELERLEAREL ALES AN NNN h2 4 6 8 10 12 14 16 18 20 22 24 2 4 Keypad Lock By pressing the Mode and Minus buttons simultaneously for 3 seconds the block symbol will be displayed and all buttons will be locked Thus at the pressing of any buttons the remote control will not respond By pressing once again the Mode and Minus buttons simultaneously for 3 seconds the block symbol will disappear and the buttons will go back to being operational Fig 7 Comfort mode all Comfort mode all Comfort mode all key unlock key is lock kez unlock gt WD me Press Mode MF MG Press Mode Trt hr le J AS a e IF a D YV EU HLI and Minus CU Li and
15. y and time Stand by mode Comfort mode TAA AAS a p m Fea moo ee gc Cx Press Press ra Ji C Press After 3 pm a d by Stand by Mode EOCENO aii ve Goe ooo m pee Pare alaala ETETETT Y papauta eTe F ro T LALI LOLI IL a LOI LOI T soak ena E K Press Mode key FA ha TT MO a FA ne et P i G Press ha op Press hi ifi C Press a GC Mode ide SEER Mode TT key key br _key if TOF Col OT imi Toll me l TON Bol OF 0 TOIT VAT II K OOI oI LOO HHHH eee ee he a ci A baits de d 1 CECE EILLLLLE J L j Fil pilot mode Clock mode Antifreeze mode Night mode 2 Once date hour minutes are set and once having switched to stand by mode press the Stand by button the remote control will switch to Comfort mode From the Comfort mode by pressing the Mode button the Night mode will be activated Similarly by pressing the Mode button again the remote control s modes will FunkydeaT switch to Comfort Mode Night Mode Antifreeze Mode Clock Mode Pilot Wire Mode Comfort Mode Comfort and Night Modes setting of the mode s temperature see Fig 1 1 Go to Night or Comfort mode use Plus or Minus buttons for temperature setting by pressing the Plus button once the temperature will rise by 0 5 degrees by pressing the Minus button onc
Download Pdf Manuals
Related Search