1 - Multi Functional Weighing Scale
Contents
1. In the dialog box Accessibility Options enter General option choose Use Serial Keys and press Settings In the dialog box Settings for SerialKeys set the corresponding Serial port and Baud rate which should be same as Baud rate in scale Sak Accessibility Options Keyboard Sound Display Mouse General Automatic reset C Turn off accessibility features after idle for Settings for SerialKeys fal E Notification SE l l l Choose the port where you connect an alternative input device Give Warning message when turning a feature on Make a sound when tuming a feature on or off Serial port Baud rate Dertalk eu devices CoM E Genelk eu devices allow alternative access to keyboard and mouse features Use Serial Keps Administrative options C Apply all settings to logon desktop C Apply all settings to defaults for new users 3 Test if Serial Keys works well Open a Text Document and press the Print buotton on the scale The Serial Keys works well if pc exports the weighing data to Text File Edit Format View Help 200 00 16 Export weighing data to Excel 1 Open Excel 2 Press Print then Excel will show Weighing data File Home Insert Page Layout Formulas Data Review View Loi Fei A SE a wl e ne Calibri eil ri A A EE General DE if2. articles 2 LOAD CELL failure which requires to be changed or to contact our Service 1 Check whether it is A D failure if yes Exceed the A D resolution please replace AD range 2 LOAD CELL failure replacement is required or contact our Service ERRA EEPROM failure Re sold EEPROM or contact our Service Remove weight that is greater than the scale Overload condition E from the pan ERR6 _ Exceeds the display range Accumulated number of weights i a the exceeding weights ERR7 exceeds the display range ERR8 evel EE VA ES MaN ee2iineweiahelimivalie the full load value The tare value should be over zero and less Exceed tare or pre tare range than or equal to full load Wiolig calibration weiohis Place the right weights the calibration value lt full load Appendix 1 Printing format Optional pee Cee 1 500 kg 0 500 kg 1 000 kg 1 000 kg ST stable UT unstable NW net weight GW gross weight ST stable UT unstable NW net weight GW gross weight ST 100 00kg ST 100 00kg ST is the prefix BIRCH GODEX ZEBRA GP ICK 1 500 kg 0 500 kg 1 000 kg 14 G W 100 00 kg T W 0 00 kg N W 100 00 kg 1 765 kg appear under 1 760 kg display of accumulation 1 760 kg press key PRINT to the print out 5 285 kg NOTE The printing sample could be of different kinds of formats When there is specific demand about the format conduct as fo
3. display parameter accumulated number of weighments TARE Symbol VY points at TARE when manual Tare action is done PRESET TARE Symbol eg points at Preset Tare when preset tare value is set NET Net weight Gross weight minus Tare Symbol VY points at NET when manual Tare or preset are actions are done UW Under simple counting mode Symbol VY points at UW when unit weight is lower than 4 5 of scale division Unit weight is too small for ensuring accurate quantity calculations e Charge Lamp CHARGE Red battery is charging Green battery is fully charged HI LAMP ON The weight on the weighing pan is greater than the upper limit OK LAMP ON The weight on the weighing pan is between upper and lower limits LOW LAMP ON The weight on the weighing pan is smaller than lower limit Pe Units of measure Jr Fa lboz kg m amp 4 Stable indication 4 2 2 Keyboard OO O a dm mi el O m o EI Se Short press steps through activated weighing units release on desired one Displays gross and net weight by turns N N N SP ie SS Tares the weight of the container or accepts the keypad tare entries Preset Tare and Cancel the tare Select the later parameter in the same level Select the later record when checking the accumulation record Shift keys rightwards Zeros the display within 2 of max capacity Exits from c
4. enter function setting The window displays check Setting item P00 displays momentarily at the left bottom 2 Press lt MR or TARE to shift between the functions 3 Press M SET to enter the parameter setting 4 Press lt MR or TARE to shift between the function parameters 5 Press M SAVE to save and return 6 Press ZERO ESC to exit without saving and return to the normal weighing model 5 2 Description of Parameter Values j d j l 1 POO LIT Offset value Displays the offset value and the keypad testing can be conducted I T 2 P01 L WHE Backlight mode Off No backlight Auto Auto on once get a stable weigh data or any key is pressed But auto off after N 5 seconds N 2s 5s 10s 20s ever with no action Ever It is always on when the weights over 9e On Backlight on P02 Un iL current using units setting Init Press key Unit to select the default unit when powering on the scale pcs Jf Ib oz g kg final final keep the final being used unit when power off Use Press key Unit to select the weighing unit on Enable the unit off Disable the unit POS d d TU zero range setting d0 d1 d2 d3 d4 d5 dO one division d1 2 divisions d2 3 divisions d3 4 divisions d4 5 divisions and d5 6 divisions P04 Hoi d Hold function HoLd 0 no hold function HoLd 1 Peak hold Press any key to release HoLd 2 Hold after stable Press any key to release HoLd 3 Hold after stable Re
5. to PO9 PE rt Press M SET to enter the external device setting Press lt MR or TARE to choose the printer model 3 After choosing one printer model press M SET and the window will show UNSUP or INIT UNSUP means the printer can t be initialized by scale Press ZERO ESC to return init means the printer is should be initialized Press MR SAVE to initialize the printer When the initialization is finished the window will show ok And then displays the printer model Press ZERO ESC to return 7 7 Input commands Connect the scale to computer Run serial port debugging program on the computer Input the capital number Z T R C P in the sending area and the indicator can conduct the corresponding actions Z zero T tare C cancel tare R P reading print 8 Serial Interface If external interface is needed please select the proper RS 232 board or Relay port firstly and only when this board is adopted the functions can be enabled Note RTC is unavailable 8 1 RS 232 Diagram COMMON COM BUZZER CN2 6 RXD TO SCALE CN2 2 CHECK WEIGHT CN2 7 TXD TO PC CN2 3 CHECK WEIGHT CN2 8 CHECK WEIGHT ee CN2 9 9 Troubleshooting and Error Message Error Message Problem ERRO Exceed the zero range The item should be within 2 of full load 1 Check whether there are other alien articles on the scale pan remove those Exceed the initial zero point
6. when the weight of articles is between the upper and lower limit including the upper and lower limits and the weight is equal or more than 20d out There will be a warning sound when the weight of articles is beyond the upper or lower limit and the weight is equal or more than 20d no beep no beep 9 POS Hie t External device h ir L H Birch printer BP545 TDP643 ode i Godex printer P dch f Zebra printer GP Adhesive sticker label printer paper size 5cmx3cm dur Dot matrix printer SH 24 E t Large LED display Pr L Computer Deen the weighing managing system CX large screen display version 0 02 rf Thermal printer Chinese available Lant the output format is compatible with Toledo Continuous Mode Note Special setting is needed by distributor if you want to print in Chinese SIB Work with the function of Use Serial Keys in Windows in outputting the data to Excel or others U KEY U KEY connector works with PC to send the weighing data to computer a in form of Excel and so on 10 P09 Wi 1 RS 232 Serial Transmission Rate 9600 4800 gt 2400 11 P10 Hr En Print mode contin Continuous print stable Printing automatically when get a stable weight more than 20d key Manual print by pressing the key PRINT 12 P11 He I A printing format setting prt01 prt03 Use the numeric key to set the format directly T 13 P12 F L Filtering setting 1 2 3 4 Set the filtering level in which
7. CONTENTS POT ie elo LE eld 6 EE 2 Precautions EEEE EEEE 3 Before Using the Product 3 1 JNPACKING and GCNECK IN e e sie ieades 3 2 E ll ln e BE ele lge En EE 379 E le Le une E 4 Product Introduction 4 1 Specifications amp General Features ccc cece cece e eee e ee eee easeteeeeaeteneeeeetseeaeeeenenseens Ask ONC AME EE 422 1 BCD E EE BZ CV OO EE 43 OWE SUDO EE 5 Function Setting and Description of Parameter Values E le Leen due eee ene ene ree ar ene on Een eee ene eee ee ont ener re 5 2 Description of Parameter Values cece cece eee eee eee ne ee tees eee eeaeeeeeeeeeeenaaaeeeeeeas 6 CGalbraton ccc 7 Operation PED AN CIOIMING EE EE 7 2 manual tare amp presSet Iore ccc cece cece cece eee eect eee eee n eee e tees ee eenaeeteeeeeenaaaeaeeees 1 3 CNCCK WINING eeu cxtsncsocte sateen ee 724 Simple COUMUMNG KEE 7 5 Accumulation Accumulation Display and Accumulation Cleamg 7 6 Printer initialization by the indicator operaton 0 cece cece cece cece eee eeeeeeeeeeeeenaaes F IOUT COMMING EE 8 Serial Interface DIAQEAIN getigert 9 Troubleshooting and Error Message Appendix 1 printing format Optional Appendix 2 Exporting data to PC in the form of EXCEL Appendix 3 U KEY Connector 1 Introduction This manual contains installation and operation instructions for the CYD W 8 Series weighing scale Please read the manual completely before installation and operation 2 Precautions Place th
8. E Z MESSE A A ae r Clipboard T Font F Alignment F Humbe C D E F WEIGHT KG gt 0 240 D 0 371 Fi 0 378 5 3 Use Format Cells to beautify Excel i Format Cells EH x Category General ec Sak 300 00 Currency Accounting Date Time E Use 1000 Separator Percentage Decimal places 2 FS Negative numbers 1234 10 Number is used for general display of numbers Currency and Accounting offer specialized formatting for monetary value Troubleshooting 1 Enable Fast User Switching function will disable Use Serial Keys in the computer Note Start gt Control Panel gt User Account gt Fast User Switching function 2 The data export requires only GND RX TX three lines while some wire include nine lines including usb 9 25pin adapter which may cause abnormal function Note cut other useless line to check if these three lines work well 17 Appendix 3 U KEY Connector Introduction Connect the scale with PC and set the parameter of external device as U KEY on the scale then you could export the weighing data to PC in the form of EXCEL With this function you could record accumulate average data statistical analysis the testing data which we could call it as scale computer data management function Most importantly you don t need any setup in computer but only use U KEY connector to link computer system directly such as EXCEL Express System ERP system a
9. ESS ei WEIGHT 64440 KG wo oo0001 DELIVERY COURIER mRz ei AREA usa e pate zoso sl 19
10. I to increase setting values and key HOLD LO to decrease setting value 3 To save the upper limit and return to weighing mode press key M SAVE Note Place the sample on the weighing pan if the sample weight is under the lower weight range while over or equal 20d the LOW lamp will light up If the sample is within the lower and upper weight range while over or equal 20d the OK lamp will light up If the sample is over the upper weight range while over or equal 20d the HI lamp will light up When changing the Hi Lo value the scale will activate the weighing checking function automatically If the Lo value is higher than Hi value then the Hi value will become the same value as Lo data 7 4 Simple Counting II 1 Press key UNIT to select the unit PCS C u Mook Note Ensure to activate the unit pcs before operating see the setting of PO2 LI IL 2 Long press key G N the ex factory default sample quantity 10 pcs is displayed 10 3 Use key PRINT HI or HOLD LO to choose the sampling amount Available options are10 20 50 100 200 500 1000 pieces 1 EN 4 Put the corresponding samples on the weighing pan and then press key TAREA 5 Remove the samples and put the load on the scale calculates the amount of the load 6 To go back to the normal weighing mode remove the load and press key UNIT to select the proper weighing unit Note 1 The larger the sample size the more accura
11. cator at the front panel Adjust the leveling feet until the air bubble in the indicator is centered as shown Note The scale should be leveled each time once its location is changed 4 Product Introduction Leveler Stainless Steel weighing pan 2 Keypad On Off switch 3 Adjusting feet CO Transport protection screws 4 Plastic weighing pan Power socket 4 1 Specifications amp General Features Specifications Model CYD W8 3K CYD W8 6K CYD W8 15K CYD W8 30K Display LCDiliquid crystal display digits 31mm high with back lighting Power Supply DC9V 400mA or built in rechargeable battery 6V 4A General Features Built in rechargeable batteries or DC alternative Multiple functions tare preset tare simple counting check weighing accumulation and display for every deal Large bright backlit LCD with prominent 31mm high digits and LED backlight Software filtering design and adjustable weighing displaying speed according to different environments Easy operation with big keys and high weighing resolution Single point calibration and linear calibration available RS 232 serial communication interface and Relay port optional PC printer relay 4 2 Display 4 2 1 LCD Display M HI LO STABLE EI vi CH CH CHARGE HI OK LOW Low battery indication Tare or Preset Tare Indication 0 Center of Zero Indication The zeroing range is 2 of weighing capacity HHH Auxiliary
12. e scale on a flat and stable surface Verify that the input voltage and the plug type matches the local AC power supply Refer to section 4 3 Warm up the scale for 15 minutes before using it for the first time Make sure power cord won t cause a potential obstacle or tripping hazard Keep the scale away from EMI noise strong wind and vibration which might cause incorrect reading Avoid sudden temperature changes suitable operating temperature is between 0 C 40 Gs Do not drop loads on the platform Disconnect the power supply while cleaning the scale Do not immerse the scale in water or other liquids Service should be performed by authorized personnel only 3 Before Using the Product 3 1 Unpacking and Checking Open the package and check the instrument for transport damage Immediately inform your dealer if you have complaints or if parts are missing The package should contain e Scale body e Weighing pan e Adaptor e User manual 3 2 Installing Components 1 Before using the scale remove the delivery protection screw rotate counterclockwise which located underneath the scale and cork the plug buckle Note the JWN 30K model is shipped without the shipping protection screw 2 Cover the weighing pans on the scale body properly 3 3 Leveling the Scale To compensate for small irregularities or inclinations at the location the scale can be leveled The scale is equipped with a level indi
13. e screen displays the tare value 4 To clear tare with an empty pan Press down key TARE or key ZERO ESC Preset Tare 1 Long press key TARE for 3 seconds The scale is now in Digital inputting mode with the left most digit blinking 2 Press lt MR or TARE to move leftwards or rightwards Presst PRINT HI or HOLD LO to change the value Press M SAVE to save and return to weighing mode 3 Put the load on the container the scale will automatically deduct the value of the container from the total value NOTE Press Key G N to display gross and net weight by turns 4 Clear the load on the container and press TARE or ZERO ESC to cancel the 9 pre tare 7 3 Check Weighing Lower limit setting 1 Begin by pressing down key HOLD LO The scale is now in digital inputting mode with the right most digit blinking 2 To set the value of lower limit press key lt MR to shift leftwards key TAREA to shift rightwards key PRINT HI to increase setting values and key HOLD LO to decrease setting value Key M SET to enable or disable the weighing checking function 3 To save the Lower limit and return to weighing mode Press key M SAVE Upper limit setting 1 Begin by pressing down key PRINT HI The scale is now in digital inputting mode with the right most digit blinking 2 To set the value of upper limit press key lt IMR to shift leftwards key TARE to shift rightwards key PRINT H
14. ertain operation without save Long press to enter function setting Deletes accumulation records Delete the present accumulation record for the sake of wrong accumulation operation under the accumulation mode Adds the indicated weight into accumulation memory During editing save and return to the higher option Select the former parameter in the same level Select the former record when checking the accumulation record Shift keys leftwards During setting value add 1 to the current value Set the upper limit of the check weighing Print HOLD 1 During setting value deduct 1 to the current value LO 2 Set the lower limit of the check weighing em 3 Hold function 4 3 Power supply Please verify the local power source before plugging into the power outlet and use the individual power socket and original adaptor Alternative power supply 1 9V 400mA adaptor 2 6V 4A Internal Rechargeable Battery Power Consumption About 300 mW without backlight About 380 mW with backlight Low Battery Warning When recharging The charge lamp turns green from red when the recharging is completed which appears in the upper left corner of the weight window the battery requires takes about 8 hours Disconnect the scale from power supply when it is fully charged 5 Function Setting and Description of Parameter Values 5 1 Function Setting 1 Press and hold M SET while powering on or long press M SET under normal weighing mode to
15. lease after moving away the article The hold value is based on the current value and its range could be set in sub menu Accumulation hold function is available that is you could add article after hold the first value HoLd 4 Press key HOLD LO to hold Press any key to release Sub menu for Hold 3 INF default infinity 10 20 50 100 200 500 1000 2000 5000 10000 20000 50000 H current hold value R hold value range d division W actual weight Keep to hold the value when W H lt R d or the scale will exit the hold function The scale will cancel the hold function when empty the weighing pan if choose INF setting _ P05 buy whether to save the upper amp lower limit of quantity checking on off OFF previously set quantity checking values are not retained when the unit is turned on ON previously set quantity checking values are retained when the unit is turned on POG L AAL Check weighing function on Check weighing under the condition that the weight is within the limits and the stable indication appears off Check weighing under the condition that the weight is within the limits P07 ht i p Check Weighing buzzer beep Hi There will be a warning sound when the weight of articles exceeds the upper limit and 6 the weight is equal or more than 20d LO There will be a warning sound when the weight of articles exceeds the lower limit and the weight is equal or more than 20d ok There will be a warning sound
16. llows 1 As for BRICH GODEX ZEBRA GP printers the factory designs the format as planned and email to the user Add the format into the previous format file via computer Then it is successful to add the new format and able to print the new format 2 As for DMP CK printer it needs to change the scale design Appendix 2 Exporting data to PC in the form of EXCEL Introduction Connect the scale with PC and set the parameter of external device as EXCEL on the scale then you could export the weighing data to PC in the form of EXCEL With this function you could record accumulate average data statistical analysis the testing data which we could call it as scale computer data management function Note pls enable Use Serial Keys function in the computer Hardware connection and settings 1 Use transmitting serial wire or USB wire to connect scale and pc Note pls install usb driver first if you use usb wire 2 Parameter settings in scale PERI EXCEL external device BAUD 2400 4800 9600 baud rate PRT M KEY STABLE printing model PRT F PRT FOI printing format Enable the function of Use Serial Keys in the computer Set Windows XP as a example 1 Press Start gt Run and enter access cpl Ok Run ameman Kach Type the name of a program folder document or Internet resource and Windows will open it for you Open access cpl Cancel Browse 2
17. n be recorded If the capacity has been changed the default value is 1 3 of full load If you need to change the value do as the following Press M SE Tito enter the value setting Press lt MR or TARE to move leftwards or rightwards Presst PRINT HI or HOLD LO to change the value Press M SAVE to save 4 Put the corresponding weight on the weighing pan and then press TARE to complete the first point calibration oo appears at the left bottom l Note After the first point calibration the window can display the weight value If no need 8 for the other point calibration move to step 6 to finish the calibration procedure 5 Add another mass to the current weight The window will show the total weight Press TARE to complete on J appears at the left bottom Loi js 6 Press M SAVE to save After the window displays d Ta it will return to normal weighing mode 7 Operation 7 1 Weighing Begin with no load on the scale the display reads zero Place item s to be weighed on the scale The display shown is 1000 0g gross weight The desired weighing unit should be selected before weighing refer to section 7 5 7 2 Manual Tare amp Preset Tare When weighing a sample that must be held in a container tare and store the container weight into memory Manual Tare 1 Under the weighing mode place the container on the weighing pan wait till stable 3 Remove all items from the weighing pan th
18. nd so on This connector is compatible with windows2000 xp Vista win7 win8 Linux Android system and the weighing data will show on the position where the mouse cursor in With one USB port you could connect scale to computer easily Precaution 1 Close the input method program before connecting 2 Ensure the decimal point digit is same as the parameter setting of scale if use EXCEL file in computer For Example Scale shows Total Weight 1 000KG Unit Weight 0 001g Total LOOOPCS EXCEL Setting the decimal point digit should be 3 for total weight and unit weight column and the decimal point digit should be O for total column Setting 1 Prepare one computer with windows2000 xp Vista win7 win8 Linux system or Android pad 2 Scale setting PERI U KEY External devices BAUD 9600 Baud PRT M KEY STABLE Print Mode RTC ON OFF Time 3 Open the receiving port such as EXCEL or ECR system and the weighing data will show on the position where the mouse cursor in JU Example 1 EXCEL 18 LOG IN z crosoft Excel VWorksne Home Insert Page Layout Formulas Data Review View Loi q dr m I I Calibri 111 Font E Alignment E bag 4 ES 4 d q INi ii ll Ws NI W I NI Sins General Yo 3 Numbe EUR Er DS ae Pee eee EXPRESSITME EXPR
19. te unit weight 2 Symbol V points at UW when calculated unit weight is lower than 4 5 of scale division 7 5 Accumulation Accumulation Display and Accumulation clear Accumulation Under the weighing mode put the item on the weighing pan Press key M SAVE at the appearance of tm ddd is displayed momentarily before the display reverts to the weight of the item Remove the item and the display goes back to zero before the next accumulation can register The maximum is 99 pieces display the latest 10 accumulation events in details Accumulation Display Press key lt V MR to display the accumulation data Press key lt MR or TARE to check a total accumulation event and each accumulation event in detail The number of accumulated weight is indicated at the left bottom tXX total accumulation event 11XX the single accumulation Accumulation Clear To clear accumulation data total accumulation data or one of the latest 10 accumulation events press key lt MR_ to display the accumulation data needed and press key M SET to clear data chosen When clear total accumulation data the accumulation signal y will disappear and back to normal weighing mode If need to exit without clearing data 11 and return to normal weighing mode press key ZERO ESC 7 6 Printer initialization by the indicator operation Press M SET while powering on to enter parameter setting Use key lt MR or TARE gt to shift
20. the stable indication turns on The higher the setting the slower stabilization time 14 P13 d E Precondition for zeroing or taring setting stable auto always stable Taring or zeroing can be not action without stable indication after pressing the key TARE or ZERO always Taring or zeroing can be action without stable indication after pressing the key TARE or ZERO auto Press key TARE or ZERO but it works only when get the stable indication 15 P14 ore Zero Offset function ON display the previous weight when powering on again OFF not display the previous weight when powering on again V E lar 16 P15 FE IE Initialization Press M SET then press M SAVE to start initialization and the window display RESET 6 Calibration Note Before calibration please set the unit first The unit used in calibration must be the one that has been set before P02 Un iD During the calibration procedure press ZERO ESC to return to normal weighing mode without saving Here we take 3kg 1g as an example 1 Press and hold TARE while powering on Do not release it till the window displays CAL 2 With no load on the weighing pan press TARE to start zero point calibration 8 t is blanking at the left bottom 3 Wait till the window displays the first calibration value Of appears at the left bottom Note The first calibration value is default With the same capacity the last first calibration point value ca
Download Pdf Manuals
Related Search