M68HC05PGMR
Contents
1. Always ensure that the devices are orientated correctly into their respective sockets M68HCO5PGM R 2 D 2 6 MOTOROLA CHAPTER 2 PROGRAMMING PROCEDURES The programmer copies a user program contained in an external EPROM into the internal PROM OTPROM EPROM or EEPROM C4 only of the MCU device The following sections describe the procedure taken to program each MCU type 2 1 68HC805C4 PROGRAMMING AND VERIFYING There are two procedures used one for programming and verifying and one that allows verifying only 2 1 1 Programming Procedure Settings required JP No Connection JP2 C4 C8 JP3 4 8 4 27C64 27C128 JP5 PROG Sl OFF S2 IN S3 OFF OFF OFF OFF SKTI 27C64 EPROM Installed a Apply power to the PGMR board b Insert the 805C4 MCU device into the PGMR Set S1 to ON d Set S2 to OUT The selected programming routine is then executed Once the programming is complete see section 2 1 2 set S2 to IN and 51 to OFF You may now remove the MCU from the socket 2 1 2 Notes on the Programming Operation In the program and verify MCU PROM routine the contents of an external EPROM are copied into the MCU EEPROM There is a direct correlation of addresses between the two devices MCU and external EPROM Non MCU EEPROM addresses are ignored so data contained in those areas are not accessed Unprogrammed EEPROM address locations should contain FF to speed up the programming operation During the programming r2. address location will be placed on the external memory address bus NOTE MCU EPROM blank checking can be accomplished by placing 00 into the locations of the external EPROM that map those of the MCU EPROM The above verify MCU routine will then verify that the device is blank M68HCO5PGM R 2 D 2 15 MOTOROLA This page intentionally left blank M68HCO5PGM R 2 D 2 16 MOTOROLA
3. is complete set S2 to IN and S1 to OFF You may now remove the MCU from the socket M68HCO5PGM R 2 D 2 13 MOTOROLA 2 4 68HC705C9 D9 PROGRAMMING AND VERIFYING There are two procedures used one for programming and verifying and one that allows verifying only Use the same procedure for a C9 or a D9 2 4 1 Programming Procedure Settings required JP No Connection JP2 C9 D9 JP3 C9 D9 JP4 27C64 27C128 if27C128 installed 27C256 if 27C256 installed JP5 PROG Sl OFF 2 IN 53 OFF OFF OFF OFF SKTI 27C128 or 27C256 EPROM Installed a Apply power to the PGMR board b Insert the 705C9 or 705D9 MCU device into the PGMR Set 51 to ON d Set S2 to OUT The selected programming routine 1s then executed Once the programming is complete see section 2 4 2 set S2 to IN and 51 to OFF You may now remove the MCU from the socket 2 4 2 Notes on the Programming Operation In the program and verify MCU EPROM routine the contents of an external EPROM are copied into the MCU EPROM There is a direct correlation of addresses between the two devices MCU and external EPROM Non MCU EPROM addresses are ignored so data contained in those areas are not accessed Unprogrammed EPROM address locations should contain 00 to speed up the programming operation During the programming routine the PROGRAM LED D6 is illuminated At the end of the programming routine D6 is turned off and the verification routine is entered If the contents of the
4. turned off at this time until verification is completed Upon completion of the verification routine every location verified the VERIFIED LED D5 is illuminated If 05 does not illuminate a discrepancy has been detected and the error address location will be placed on the external memory address bus NOTE MCU EPROM blank checking can be accomplished by placing 00 into the locations of the external EPROM that map those of the MCU EPROM The above verify MCU routine will then verify that the device is blank M68HCO5PGM R 2 D 2 12 MOTOROLA 2 3 5 Secure EPROM Operation The 705C8 contains a security bit that prevents reading of the internal EPROM Use the secure PROM routines after you successfully program and verify the EPROM This procedure only programs the SEC bit of the OPTION register 1FDF but VPP is necessary Once this bit is programmed PROM is secure and you cannot verify it No LED illuminates during this routine and no verification occurs To ensure that security is proper enabled attempt to perform another verify routine 2 3 3 If the green LED does not light the EPROM is secure Settings required JP No Connection JP2 C4 C8 JP3 4 8 4 27 64 27 128 5 PROG Sl OFF S2 IN S3 OFF ON OFF ON SKTI 27C64 EPROM Installed a Apply power to the PGMR board b Insert the 705C8 MCU device into the PGMR Set 51 to ON d Set S2 to OUT The selected programming routine executes Once the programming
5. use 2 14 2 4 1 Programming Procedure renier met tentera fe GEI 2 14 2 4 2 Notes on the Programming Operation ses 2 14 2 43 Verifying Proc dures same ennemie 2 15 2 4 4 Notes on the Verifying Operation ss 2 15 M68HCO5PGM R 2 D 2 3 MOTOROLA THIS PAGE INTENTIONALLY LEFT BLANK M68HCO5PGM R 2 D 2 4 MOTOROLA CHAPTER 1 INTRODUCTION This manual describes the procedure used to program and verify an MC68HC 7 8 05C series microcontroller MCU on M68HCOS5PGMR 2 that is required to program the MCU is the PGMR 5 volt and Vpp dc power supply and a pre programmed EPROM The PGMR provides programming for either 40 pin dual in line package DIP MCU device programming or 44 pin plastic leaded chip carrier PLCC MCU device programming S1 controls power S2 controls the Jumper Headers Install power to the MCU MCU RESET configure the PGMR leads at P1 JP1 JP2 JP4 SKT1 contains Install the 40DIP OR Install the 44PLCC the program EPROM in SKT2 in SKT1 Figure 1 1 M68HCO5PGMR 2 Layout M68HCO5PGM R 2 D 2 5 MOTOROLA 1 1 BOARD LAYOUT AND DESCRIPTION Figure 1 1 shows the layout of the PGMR As shown in the figure there are various controls connectors and sockets that provide the ability to configure the board to specific MCU programming requirements For the board to function correctly you must supply the required power to the board at connector Pl 5V dc 1
6. 00mA and ground lines are required In addition a Vpp power supply is needed to perform the programming The value of this supply may vary between MCUs please refer to this manual and the device data book for further information Switches 51 and 52 control the activity of the PGMR 51 is a simple on off switch that applies power to the MCU device when on Never remove or install an MCU when the S1 switch is in the ON position S2 control the MCU reset line Programming cannot take place while the part is in reset mode Five jumper headers JP1 to JP5 configure the PGMR for the particular MCU and function in use They select between different MCUs EPROM sizes and modes The following sections describe how to configure these jumpers for your programming requirements Lastly sockets SKT1 to SKT3 allow for the installation of the MCUs and the master EPROM SKTI is for installation of the EPROM that contains all the data being programmed into the MCU SKT2 provides support for a 40 pin DIP package and SKT3 for a 44 pin PLCC package Not all of the MCUs supported by this board may be available in each package The SKT3 socket requires that the MCU is installed in a top down or dead bug fashion IMPORTANT NOTE You must never install more than one MCU on this board at any time That is there must never be an MCU installed in SKT2 and another installed in SKT3 simultaneously Such a configuration may damage either of the MCUs and the board itself
7. 8HCO5PGM R 2 D 2 2 MOTOROLA Table of Contents L INTRODUCTION der 222222000000 5555 CUTRE ER ERER dede 1 5 1 1 BOARD LAYOUT AND DESCRIPTION 1 6 2 PROGRAMMING PROCEDURES uses sssssssssssscssssscsessecsesecessscesssee 2 7 2 1 68HC805C4 PROGRAMMING AND VERIFYING LS 2 7 2 1 1 Programming essais natale tannins 2 7 2 1 2 Notes on the Programming Operation ss 2 7 ZA 3 VETUVING P FOCEAUPE 525203520208 sieste ht toes oy ee rimes ain 2 8 2 1 4 Notes the Programming Operation ses 2 8 2 2 68HC705C5 PROGRAMMING AND VERIFYING issu 2 9 2 21 PLOSTAMMING Procedure ue dits ent ne antenne mn nn Rene 2 9 2 2 2 Notes on the Programming Operation ss 2 9 2 23 Verifying Procedure tipirin finement hate tte n AES 2 10 2 2 4 Notes the Programming Operation sise 2 10 2 3 68HC705C8 PROGRAMMING AND VERIFYING us 2 11 2 3 1 Programming TEEST 2 11 2 3 2 Notes the Programming Operation ss 2 11 233 3 Verifying Procedu tea 2 12 2 34 Notes on the Verifying Op C1 AMON pee a ea 2 12 253 9 SECULE EPROM Op rations nn nn nr ein ann Tiens 2 13 2 4 68HC705C9 D9 PROGRAMMING AND VERIFYING
8. M68HCO5PGMR 2 D Rev 2 April 1995 M68HCOSPGMR 2 PROGRAMMER USER S MANUAL Third Edition MOTOROLA Ltd 1994 1995 All Rights Reserved M68HCO5PGM R 2 D 2 1 MOTOROLA Motorola reserves the right to make changes without further notice to any products herein to improve reliability function or design Motorola does not assume any liability arising out of the application or use of any product or circuit described herein neither does it convey any license under its patent rights nor the rights of others Motorola products are not designed intended or authorized for use as components in systems intended for surgical implant into the body or other application in which the failure of the Motorola product could create a situation where personal injury or death may occur Should Buyer purchase or use Motorola products for any such unintended or unauthorized application Buyer shall indemnify and hold Motorola and its officers employees subsidiaries affiliates and distributors harmless against all claims costs damages and expenses and reasonable attorney fees arising out of directly or indirectly any claim of personal injury or death associated with such unintended or unauthorized use even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part Motorola and the Motorola logo are registered trademarks of Motorola Inc Motorola Inc is an Equal Opportunity Affirmative Action Employer M6
9. MCU EPROM and external EPROM exactly match then the VERIFY LED DS is illuminated During the verification routine all locations are compared to the data residing in external EPROM The verification routine will stop if a discrepancy has been detected and the error address location will be placed on the external memory address bus M68HCO5PGM R 2 D 2 14 MOTOROLA 2 4 3 Verifying Procedure Settings required JP No Connection JP2 C4 C8 JP3 C9 D9 JP4 27C64 27C128 if 27C128 installed 27C256 if 27C256 installed JP5 PROG Sl OFF S2 IN 53 OFF ON OFF OFF 27 128 27C256 EPROM Installed a Apply power to the PGMR board b Insert the 705C9 or 705D9 MCU device into the PGMR Set S1 to ON d Set S2 to OUT The selected verification routine is then executed Once the verification is complete see section 2 4 4 set 52 to IN and 51 to OFF You may now remove the MCU from the socket 2 4 4 Notes on the Verifying Operation The verify MCU PROM contents routine is normally entered automatically after the MCU EPROM is programmed Direct entry of this mode will cause the MCU EPROM contents to be compared to external EPROM contents residing at the same address locations Both D5 and D6 LEDs are turned off at this time until verification is completed Upon completion of the verification routine every location verified the VERIFIED LED D5 is illuminated If 05 does not illuminate a discrepancy has been detected and the error
10. e not accessed Unprogrammed EPROM address locations should contain 00 to speed up the programming operation During the programming routine the PROGRAM LED D6 is illuminated At the end of the programming routine D6 is turned off and the verification routine is entered If the contents of the MCU EPROM and external EPROM exactly match then the VERIFY LED DS is illuminated During the verification routine all locations are compared to the data residing in external EPROM The verification routine will stop if a discrepancy has been detected and the error address location will be placed on the external memory address bus M68HCO5PGM R 2 D 2 11 MOTOROLA 2 3 3 Verifying Procedure Settings required JP No Connection JP2 C4 C8 JP3 4 8 JP4 27C64 27C128 JP5 PROG Sl OFF S2 IN 53 OFF ON OFF OFF 27C64 Installed a Apply power to the PGMR board b Insert the 705C8 MCU device into the PGMR Set 51 to ON d Set S2 to OUT The selected verification routine is then executed Once the verification is complete see section 2 3 4 set 52 to IN and 51 to OFF You may now remove the MCU from the socket 2 3 4 Notes on the Verifying Operation The verify MCU PROM contents routine is normally entered automatically after the MCU EPROM is programmed Direct entry of this mode will cause the MCU EPROM contents to be compared to external EPROM contents residing at the same address locations Both D5 and D6 LEDs are
11. g operation During the programming routine the PROGRAM LED D6 is illuminated At the end of the programming routine D6 is turned off and the verification routine is entered If the contents of the MCU EPROM and external EPROM exactly match then the VERIFY LED DS is illuminated During the verification routine all locations are compared to the data residing in external EPROM The verification routine will stop if a discrepancy has been detected and the error address location will be placed on the external memory address bus M68HCO5PGM R 2 D 2 9 MOTOROLA 2 2 3 Verifying Procedure Settings required JP No Connection JP2 C4 C8 JP3 4 8 JP4 27C64 27C128 JP5 PROG Sl OFF S2 IN 53 ON OFF OFF 27C64 Installed a Apply power to the PGMR board b Insert the 705C5 MCU device into the PGMR Set 51 to ON d Set S2 to OUT The selected verification routine is then executed Once the verification is complete see section 2 2 4 set 52 to IN and 51 to OFF You may now remove the MCU from the socket 2 2 4 Notes on the Programming Operation The verify MCU PROM contents routine is normally entered automatically after the MCU EPROM is programmed Direct entry of this mode will cause the MCU EPROM contents to be compared to external EPROM contents residing at the same address locations Both D5 and D6 LEDs are turned off at this time until verification is completed Upon completion of the verification ro
12. he VERIFIED LED D5 is illuminated If DS does not illuminate a discrepancy has been detected and the error address location will be placed on the external memory address bus NOTE MCU EEPROM blank checking can be accomplished by placing FF into the locations of the external EPROM that map those of the MCU EEPROM The above verify MCU routine will then verify that the device is blank M68HCO5PGM R 2 D 2 8 MOTOROLA 2 2 68HC705C5 PROGRAMMING AND VERIFYING There are two procedures used one for programming and verifying and one that allows verifying only 2 2 1 Programming Procedure Settings required JP No Connection JP2 C4 C8 JP3 4 8 4 27C64 27C128 JP5 PROG Sl OFF S2 IN 53 ON OFF OFF OFF SKTI 27C64 EPROM Installed a Apply power to the PGMR board b Insert the 705C5 MCU device into the PGMR Set S1 to ON d Set S2 to OUT The selected programming routine is then executed Once the programming is complete see section 2 1 2 set S2 to IN and 51 to OFF You may now remove the MCU from the socket 2 2 2 Notes on the Programming Operation In the program and verify MCU EPROM routine the contents of an external EPROM are copied into the MCU EPROM There is a direct correlation of addresses between the two devices MCU and external EPROM Non MCU EPROM addresses are ignored so data contained in those areas are not accessed Unprogrammed EPROM address locations should contain 00 to speed up the programmin
13. outine the PROGRAM LED D6 is illuminated At the end of the programming routine D6 is turned off and the verification routine is entered If the contents of the MCU EEPROM and external EPROM exactly match then the VERIFY LED DS is illuminated M68HCO5PGM R 2 D 2 7 MOTOROLA During the verification routine all locations are compared to the data residing in external EPROM The verification routine will stop 1f a discrepancy has been detected and the error address location will be placed on the external memory address bus 2 1 3 Verifying Procedure Settings required JP No Connection JP2 C4 C8 JP3 4 8 4 27C64 27C128 JP5 PROG Sl OFF 2 IN 53 OFF ON OFF OFF 27C64 Installed a Apply power to the PGMR board b Insert the 805C4 MCU device into the PGMR Set 51 to ON d Set S2 to OUT The selected verification routine is then executed Once the verification is complete see section 2 1 4 set 52 to IN and 51 to OFF You may now remove the MCU from the socket 2 1 4 Notes on the Programming Operation The verify MCU EEPROM contents routine is normally entered automatically after the MCU EEPROM is programmed Direct entry of this mode will cause the MCU EEPROM contents to be compared to external EPROM contents residing at the same address locations Both DS and D6 LEDs are turned off at this time until verification is completed Upon completion of the verification routine every location verified t
14. utine every location verified the VERIFIED LED D5 is illuminated If 05 does not illuminate a discrepancy has been detected and the error address location will be placed on the external memory address bus NOTE MCU EPROM blank checking can be accomplished by placing 00 into the locations of the external EPROM that map those of the MCU EPROM The above verify MCU routine will then verify that the device is blank M68HCO5PGM R 2 D 2 10 MOTOROLA 2 3 68HC705C8 PROGRAMMING AND VERIFYING There are two procedures used one for programming and verifying and one that allows verifying only See section 2 3 5 for procedures used when securing the C8 EPROM 2 3 1 Programming Procedure Settings required JP No Connection JP2 C4 C8 JP3 4 8 4 27C64 27C128 JP5 PROG Sl OFF S2 IN 53 OFF OFF OFF OFF SKTI 27C64 EPROM Installed a Apply power to the PGMR board b Insert the 705C8 MCU device into the PGMR Set 51 to ON d Set S2 to OUT The selected programming routine is then executed Once the programming is complete see section 2 1 2 set S2 to IN and 51 to OFF You may now remove the MCU from the socket 2 3 2 Notes on the Programming Operation In the program and verify MCU EPROM routine the contents of an external EPROM are copied into the MCU EPROM There is a direct correlation of addresses between the two devices MCU and external EPROM Non MCU EPROM addresses are ignored so data contained in those areas ar
Download Pdf Manuals
Related Search
M68HC05PGMR