SVG300S+ 2 FXS SIP/IAX ATA USER MANUAL
Contents
1. into any language in any form or by any means electronic mechanical magnetic optical chemical manual or otherwise without the prior written permission of Stephen Technologies Co Limited Disclaimer Notice No license is granted implied or otherwise under any patent or patent rights of Stephen Technologies Co Limited Stephen Technologies Co Limited makes no warranties implied or otherwise in regard to this document and to the products described in this document The information provided by this document is believed to be accurate and reliable to the publication date of this document However Stephen Technologies Co Limited assumes no responsibility for any errors in this document Furthermore Stephen Technologies Co Limited assumes no responsibility for the use or misuse of the information in this document and for any patent infringements that may arise from the use of this document The information and product specifications within this document are subject to change at any time without notice and without obligation to notify any person of such change STEPHEN TECHNOLOGIES CO LIMITED 1204 LiuXiuShengChuangYeDaSha High Tech Park Southern Area Shenzhen China 518057 Tel 86 755 83016956 Fax 86 755 83016321 Website www stephen tele com Fi ERREUR RAY www stephen tele com2. SIP STUN Switch Stun switch of this line for SIP signal RTP STUN Switch Stun switch of this line for codec of voice RTCP Switch Enable or disable the RTCP SIP Forward Parameters Set the Forward type and number for SIP protocol IAX Switch Enable or disable this line s register of IAX2 account IAX Parameters Configure the IAX account information Username Username of your IAX account Password Password of your IAX account Server Addr Register address of IAX server IAX Remote Port Register server port IAX Local Port Configure the local signal port IAX Register Interval Configure expire time of the IAX server register IAX Codec PRI Setting the prefer codec in order Support 6729 6723 PCMU G711u PCMA G711a 3 4 6 Updating Configurations page The default path is our FTP server If you want to use the default path turn Use Default Server to Yes and press Apply If you want to use another server select No and input the parameters needed and then press Apply TUAM 8 www stephen tele com Current Configurations Basic Configurations Advanced Configurations Line1 Configurations Line2 Configurations PN Configurations Provision Configurations User Management Factory Reset Rebooting System Logout Updating Configurations Use Default Server O No Yes FTP Server Parameters Server Addr 192 168 1 254 Server Port 21 Directory update Username
3. Root has no limit 3 4 2 Current Configurations page After logon the Current Configurations page will show the information about firmware version accounts and network parameters KR ERREUR RAY www stephen tele com Basic Configurations Advanced Configurations Line1 Configurations Line2 Configurations Updating Configurations PN Configurations Provision Configurations User Management Factory Reset Rebooting System Logout Current Configurations ATA Version Hardware Version Software Version Account Line1 SIP Username Line1 IAX Username Line2 SIP Username Line2 IAX Username CBD 420 2008 06 16 08 56 USER UserName USER2 UserName Network Configurations WAN Port Mode Static DHCP PPPoE WAN Port IP Parameters IP Addr Subnet Mask Gateway DNS1 PPPoE Username LAN Port IP Parameters IP Addr Subnet Mask 192 168 1 58 255 255 255 0 192 168 1 1 192 168 1 1 00 0a a5 51 20 02 user 192 168 0 1 255 255 255 0 ATA Version shows the hardware and the software version of this ATA device Account shows the account username which is in using Network Configurations show the network mode IP parameters and NAT 3 4 3 Basic Configurations page SVG300S 2 FXS Sip IAX ATA User Guide In the Basic Configurations page parameters about network time server and time zone can be set gt Ifthe network administ
4. SVG300S device primitively by analog telephone keypad after the device booting up All the operations are invalid before entering the debug mode a Off hook or press handsfree Press 8356 on keypad in sequence to enter the analog phone debug mode b Functions 100 Set the WAN IP address 101 Set the WAN subnet mask 102 Set the WAN default gateway 103 Set the WAN first DNS server 104 Set the WAN IP mode 105 Set the LAN IP address 106 Set the LAN subnet mask 200 Enable Disable embedded web server 300 Enable Disable Telnet server Vv WV 999 RESET to factory settings 1 Once the one of 100 103 is set the WAN IP mode will be set to STATIC mode For the 104 0 is STATIC mode 1 is DHCP mode 2 is PPPoE mode c Options gt O Disable Exit No gt 1 Enable OK Yes d Interval use the sing at the end input In IP SUBNET MASK GATEWAY DNS mode use to instead of Fi ERREUR RAY www stephen tele com enma aS SVG300S 2 FXS Sip IAX ATA User Guide e Usage Off hook or press handsfree Enter the debug mode first then input the function code and parameter command follow after finishing input an mark must be inputted to end this configuration Every segment MUST use to interval the next segment SAMPLES 1 Reset to the factory settings 8356 999 111 2 Set the WAN IP address to 192 168 1 100 8356 100 192 168 1 100 1 3 Set the WAN IP
5. download Password download FEN Update option No Yes Use Default Server Set Using the default update server or not Server Addr The FTP server address of update server Server Port The FTP server port of update server SVG300S 2 FXS Sip IAX ATA User Guide Directory The file path of the version ini in the update server If the file is in the root path of FTP server fill in or keep space Username The login username of the FTP server Password The login password of the FTP server Update option Set Yes and press Apply the phone will update immediately 3 4 7 VPN Configurations page The SVG300S phone implement VPN on L2TP mode The UDP tunnel mode is not available now EAL IRA IRA 8 www stephen tele com 5 SVG300S 2 FXS Sip IAX ATA User Guide PN Configurations Current Configurations PN Switch Basic Configurations off O on VPN Type Advanced Configurations 9 UDP Tunnel L2TP Line1 Configurations UDP Tunnel Parameters Line2 Configurations VPN Server Addr Updating Configurations VPN Server Port Servr Group ID Server Area Provision Configurations Code Lo User Management L2TP Parameters e VPN Server Addr VPN User Name VPN Password Factory Reset Rebooting System Logout VPN IP VPN Switch Enable or disable the VPN connect VPN Type Select the VPN type Just L2TP mode is useful now L2TP Parameters Configure
6. esee nennen nennt nnne 9 OConfigure TCP A RRRRREEEEEEEMEMM 10 Configure by Telnet mode a ro d E RR RE ERE Ee 10 11 3 3 2 Show parameters aee oe o n ine e dea 11 3 3 3 Change the value of 11 Configure via WEB Ul ihi ve s b kat a eae ete ee as 11 3 4 1 The logon eitis rms eria caede tro cttm Eire oed E 12 3 4 2 Current Configurations page cccccssscecccccecsessssaeeecesesesssseaeeeeeeseseees 12 3 4 3 Basic Configurations 13 3 4 4 Advanced Configurations page seseeeeeeeeeeeenneeee nennen 15 3 4 5 Life Configurations cua disk redeo ocu ata vx dato deduc 16 3 4 6 Updating Configurations page oreet nenne tnn ne 19 3 4 7 VPN Configurations pan Ga kk sese 20 3 4 8 Provision Configurations paie uci ean dio uut 21 3 4 9 User Management page 22 3 4 10 Factory Reset 23 3 4 11 Rebooting System page sese en nnne 24 Chapter 4 Update the Firmware 25 O Update via Telnet Mode nennen nennen nennen nnn nnne 25 QUpdate Vidi WEB bes ese t ve vit e 2
7. mode to DHCP 8356 104 1 1 4 Enable the embedded web server 8356 200 1 Configure TCP IP The default IP address of the SVG300S for LAN is 192 168 1 125 And the default Subnet Mask is 255 255 255 0 They can be changed as you desire Before configuring by Telnet or WEB mode you should know the IP setting of SVG300S and configure the PC correctly As an example we use the default values for description Connect the local PC to the LAN ports of the SVG300S with a RJ 45 cable There are two ways to configure the IP address for the PC a Configure the IP address manually The IP address is 192 168 1 xxx xxx is from 2 to 254 Subnet Mask is 255 255 255 0 and Gateway is 192 168 1 125 The SVG300S s default IP address b Obtain an IP address automatically Set up the TCP IP protocol in Obtain an IP address automatically mode on your PC The built in DHCP server will assign IP address for the PC Configure by Telnet mode In Terminal type in telnet IP address 2323 and then press Enter to access to Telnet mode About the names and explanations of parameters refer to Provisioning Guide for SVG300S pdf Fi ERREUR RAY www stephen tele com enma aS SVG300S 2 FXS Sip IAX ATA User Guide m mode can only be accessed via LAN port IP Please pay attention to the blank space in command line when configuring by Telnet mode 3 3 1 Login After login the display information will be show in Termina
8. s register of SIP account SIP Dial plan Set the sequence of this line s dial plan for SIP protocol SIP Parameters Configure the SIP account information Username Username of your SIP account Commonly the same as the phone number Display Name The display name sent to callee if sip provider doesn t send a caller ID this will be shown on the LCD of callee Need Server Support Auth name Commonly the same as the phone username Password Password of your SIP account Server Addr Register address of SIP server and port Realm Domain SIP domain which is provided by SIP server It can be the server IP or the domain name of the server or other identifier provided by the server Proxy Require Some SIP service need this parameter Register Interval SIP register expires time The SVG300S will auto configure this expire time to the server recommended setting if it is longer from the SIP server Heartbeat Interval Send heartbeat pack periodically to keep the channel Options Interval Send option signal to SIP server periodically to detect if the SIP server is available SIP DTMF Parameters DTMF signal sending mode and pay load Support Inband RFC2833 and Info SIP Codec PRI Setting the prefer codec in order Support 6729 6723 PCMU G711u PCMA G711a RAS www stephen tele com d SVG300S 2 FXS Sip IAX ATA User Guide SIP Crypto Support Set the parameters to encrypt the signal Need the SIP server to support
9. the VPN parameters VPN Server Addr Configure the server address of VPN VPN User Name Configure the login username of VPN connect VPN Password Configure the login password of VPN connect VPN IP Show the IP after login 3 4 8 Provision Configurations page If you do not use provision function set the switch to off else set it to on There are two type provisions HTTP and FTP mode Select a mode and input correct value of provision parameters Do not forget to press Apply after changing RAS www stephen tele com Provision Configurations Current Configurations Provision Switch Basic Configurations x off O on Provision Type Advanced Configurations HTTP O FIP Line1 Configurations Provision Parameters Server Addr 192 168 1 254 Line2 Configurations Server 121 Updating Configurations Weemenat nee p PN Configurations Password voip Group ve Provision 1 User Management TEST L Days Factory Reset Rebooting System Logout Provision Switch Enable or disable the provision function Provision Type Select the provision type Server Addr Provision server address Server Port Provision server access port Username Provision server login username Password Provision server login password Group The folder s name which you put the setting ini in Provision Internal Set the internal of provision function 3 4 9 User Management page Se
10. 00S 2 FXS Sip IAX ATA User Guide Default Protocol sip SIP Switch off O on SIP Dial Plan Sequence SIP Parameters Username USER Display Name DISPLAY NAME Auth Name AUTHNAME Password se Server Addr 192 168 1 254 A 5060 Port Realm Domain REALM Register Interval 3600 5 0 indicates OFF Heartbeat Interval 20 s 0 indicates OFF Options Interval 0 5 0 indicates OFF SIP DTMF Parameters DTMF Made SIP Codec PRI Primary Secondary Tertiary Quaternary SIP Crypto Support Crypto Server Addr Crypto Server Port Cipher Algorithm Cipher Blocksize SIP STUN Switch RTP STUN Switch RTCP Switch SIP Forward Parameters Forward No Forward Type rrc2833 A s729_ K c723_ E ecm Pema EJ 192 168 1 254 55060 off O AES 128 256 off O on off O on off O on 10000 NONE MM Payload ECTS www stephen tele com 3r SVG300S 2 FXS Sip IAX ATA User Guide IAX Switch off O on IAX Parameters Username UserName Password 99290999 Server Addr IAX HOST IAX Remote 459 IAX Local Port 459 1200 5 0 indicates OFF IAX Codec PRI Primary EAH v Secondary EAM v Tertiary Quaternary Pema Yi ETE Default Protocol Set the Line1 default protocol when dialing out SIP Switch Enable or disable this line
11. 5 Chapter 5 Usage of the SVG300S 26 el rcsadelu E 26 Startia three Way ire rte o e e or e Ee oe ske E RR HE RH 26 OReceive an incoming call eseessseseeseeeeenenne eren nnne nnne nnne nnne nennen 26 Multi line arid share line s s ctt hr te e e te t c i e e e ne de e n dala 26 OCall Fonwarding ske e a e eer e e ie o b i 26 OSend FAX EE 26 Using the route and DHCP server sssssssseeseeeeeeee ener nennen tnnt inrer enne 27 RAS www stephen tele com enma Preface SVG300S 2 FXS Sip IAX ATA User Guide OQ About this Manual This guide provides the information you need to understand install configure and manage the SVG300S on your network It provides the required steps to get the SVG300S up and running on a SIP or IAX network Not all features listed are available by default Contact your network administrator or service provider to find out which features and services are available to you on your system Audience Network engineers system administrators and end users who need to understand how to install and use the SVG300S on a SIP network should review this guide Prior knowledge of IP telephony concepts and IP networking is recommended Related Documentation Dial Plan Guide For SVG300S pdf The user guide of local dial plan for SVG300S Provisioning Guide for
12. IP address in the IP field Set subnet mask in the Subnet Mask field Set gateway IP address in the Gateway field Set DNS IP address in the DNS1 3 field Press Apply Configure to dynamic obtain IP Enable DHCP Press Apply Configure PPPoE EAL IRA IRA 8 www stephen tele com 2 Enable SVG300S 2 FXS Sip IAX ATA User Guide Enter PPPoE username and pin in the PPPoE username and PPPoE password Press Apply LAN Port IP Parameters Set the IP and subnet mask for the NAT of LAN port DHCP Server Switch Enable the DHCP service in LAN port DHCP Address Pool Set the DHCP address for the DHCP service SNTP Configurations Set the SNTP server and time zone The default SNTP server is time nist gov and the default time zone is GMT 0 3 4 4 Advanced Configurations page In this page some common parameters can be configured Current Configurations Basic Configurations Line1 Configurations Line2 Configurations Updating Configurations PN Configurations Provision Configurations User Management Factory Reset Rebooting System Logout EAL IRA IRA 8 Advanced Configurations Caller ID Type Polarity Reverse Switch Polarity Reverse Interval VAD Switch TELCORDIA vi off O on kseconas CNG With SC silencdk Speaker And Microphone Gain dsp gain tx dsp gain rx ToS Switch ToS Para
13. N port Receiving or transmitting data through the WAN port w wc a h 3 3 A a 3 3 No link is detected at the WAN port Link is detected at the LAN port Receiving or transmitting data through the LAN port Zh a No link is detected at the LAN port Line 1 2 Green Phone connected to the port is in use gt Phone is not in use Fi UR RA a www stephen tele com enma aS SVG300S 2 FXS Sip IAX ATA User Guide Chapter 2 Install the SVG300S This section provides instructions for installing the SVG300S Before you perform the installation be sure you have met the following prerequisites gt Planned the network and SVG300S configuration gt Installed the Ethernet connection Installed and configured the other network devices 10BASE T or 100BASE T or better Ethernet cable One cable is needed for each Ethernet connection l you install an SVG300S even ifit is new upgrade the IAD device to the current firmware image For information about upgrading refer to the Chapter 4 OThe Connects of the Box The SVG300S includes these components Standard One SVG300S base unit One power adapter and cable 100 240V AC input 12V 1A output One RJ 45 Ethernet cable WV SVG300S user manual Installation procedure Step1 Place the device in a clean area that is free from environmental extremes and near an electrical power outlet Step2 Conn
14. SVG300S pdf The user guide of provisioning for SVG300S4 Document Conventions This document uses the following conventions 5 Means reader be careful In this situation you might do something that could result in equipment damage or loss of data 1 Means reader take note Notes contain helpful suggestions or references to material not covered in the publication Fi ERREUR RAY www stephen tele com enma b SVG300S 2 FXS Sip IAX ATA User Guide Chapter 1 An Overview of the SVG300S O Introduction The SVG300S provides voice communication over an IP network using the SIP or IAX It allows regular analog telephones to operate on IP based telephony networks An SVG300S like other network devices must be configured and managed Main Features e Support SIP and IAX e Support multi line and share line e Support two SIP accounts and two IAX accounts at the same time e Support two FXS ports e Support Static DHCP and PPPoE mode e Router with 1 LAN port and 1 WAN port e Support QoS ToS e Support L2TP VPN e Support fax pass through and T 38 e Support polarity reversal e Support SNTP e Support major G7 xxx codec e Support VAD CNG AEC Jitter buffer e Support Local Dial Plan e Support Info Inband and RFC2833 DTMF e Call Forward Three way conference e Caller ID displays e Provisioning function e Web UI management e Adjustable user password and super password Fi ERREUR RAY www ste
15. connect the third party Vv Vv V WV Press down hook and release it fleetly again the 3 way conference will be ok OReceive an incoming call When there is an incoming call the phone will ringing just do off hook to pick up the call Multi line and share line The SVG300S supports 2 SIP accounts and 2 IAX accounts at the same time Line1 Configurations associates with the Line1 port phone Line2 Configurations associates with the Line2 port phone But if one line is set to off for example Line2 Configurations are off no register switch is on mode Line1 port phone and Line2 port phone both associate with the Line1 account When on a call and a new call comes in the other will ring OQ Call Forwarding The SVG300S can provide you a VOIP call forward function a call can be forward to another VOIP number or PSTN number Please set this function in Line Configurations page This function is only for SIP accounts OQ Send a FAX SVG300S support FAX by T 38 or pass through mode When using pass through mode the codec must be or PCMA Fi ERREUR RAY www stephen tele com enma b SVG300S 2 FXS Sip IAX ATA User Guide O Using the route and DHCP server Connect the PC to the LAN port of SVG300S and set the TCP IP mode of PC to DHCP the PC will get network parameters automatically Copyright Notice No part of this document may be reproduced transmitted transcribed stored in a retrieval system or translated
16. ect one end of a telephone line cord to the Line1 input port on the rear panel of the SVG300S Connect the other end to an analog telephone set or fax machine Step3 Optional Connect the second telephone or fax machine to the SVG300S Line2 port Step4 Connect one end of a standard RJ45 Ethernet cable to the WAN port on the rear panel of the SVG300S Connect the other end to your IP network device such as a hub switch or directly to the Network Step5 Connect one end of a standard RJ45 Ethernet cable to LAN port on the rear panel of the SVG300S Connect the other end Fi ERREUR RAY www stephen tele com Lo SVG300S 2 FXS Sip IAX ATA User Guide to your PC Step6 Insert the power adaptor cable into the power adaptor cable receptacle on the ATA Ensure that the power adaptor jack is snugly attached to the SVG300S KR ERREUR IRAM 8 www stephen tele com enma aS SVG300S 2 FXS Sip IAX ATA User Guide Chapter 3 Configure the SVG300S This chapter provides the method to configure the device You can configure the SVG300S by analog telephone Telnet mode or WEB browser Make sure the Telnet or Http embedded is available before configuring In default setting both Telnet and WEB mode are open If you are not sure you can operate them by analog telephone Refer to Configure by Analog Telephone Configuring by provision function refer to Provisioning Guide for SVG300S pdf Configure by Analog Telephone You can configure the
17. enma d SVG300S 2 FXS Sip IAX ATA User Guide SVG300S 2 FXS SIP IAX ATA USER MANUAL STEPHEN TECHNOLOGIES CO LIMITED ALL RIGHTS RESERVED A RAS www stephen tele com enma 4d 5 SVG300S 2 FXS Sip IAX ATA User Guide Contents laa aka b kt kk r e ina lo onlo kes ke OAbout this Mata tri torret epa ooo poeta pa ri epa pad 3 nude E H ROES 3 O Related DOCUMENTATION ei eter eerte en e gan EE Ie ER E a ER Ra 3 Document CONVENTIONS ccccccccescesscesscecsccsscesscessecssecssecsecssscssecssecseecesecsscesecesecsseceseeeseeees 3 Chapter 1 An Overview of the SVG3008S d OQ Introduction 4 Mall Features err eer e 4 O Networking protocol ctt rtr net ne tn c nds 5 e RR 5 O Hardware Parameters or rite ERE ERE ER RR ERA 6 O Operating Ernivironrment scende tede teet cde bed ede ede eae d dead eee d deed eee 6 Q Front Panel LED E E 6 Chapter 2 Install the SVG300S 7 OThe Connects of the BOX iecit iii iai 7 enhn ESE EEr RA EE E etn snas nnns nns 7 Chapter 3 Configure the 5 63005 9 Configure by Analog Telephone
18. l BusyBox vi i 2007 12 12 06 58 A000 Built in shell ash Enter help for a list of built in commands 3 3 2 Show parameters Type fw printenv and press Enter the list of all parameters will be show on screen If you want to show a parameter the format is fw printenv parameter such as fw printenv UserName Bus yBox vi G1 2667 66 18 13 63 6666 gt Built in shell Cash Enter help for a list of built in commands fw printenv UserName read setting from file serName USER setting ini 3 3 3 Change the value of parameter Command fw setenv is used to configure the parameters the format is fw setenv parameter value For example change the root password to 000000 type fw setenv Root Password 000000 and press Enter fw setenv Root Password 888888 setting ini Configure via WEB UI SVG300S has a built in HTTP server With a web base utility it is easy to configure and manage the SVG300S Editing the parameters on the WEB then press Apply at lower right corner and reboot the SVG300S to make the change activated RAS www stephen tele com 5 SVG300S 2 FXS Sip IAX ATA User Guide 1 Open your web browser and typing http 192 168 1 125 in the address field Then you will see the logon page of the SVG300S 1 3 4 1 The logon page Select the user name user or root and input password to logon User is limited to change some parameters
19. meters DSCP ECN QoS Switch 10 24db 24db 10 24db 24db off O on D 0 63 0 3 O off on www stephen tele com Lo SVG300S 2 FXS Sip IAX ATA User Guide Echo Cancellation Gain for Input Medium Gain for Output Mediumi NLP Switch off Oon RTP Port Range From 49152 65535 STUN Parameters Server Addr 192 168 1 254 Server Port 3478 Caller ID Type The Caller ID type options Polarity Reverse Switch and Polarity Reverse Interval Polarity reverse function VAD Switch Enable or disable Voice Activity Detection Or switch CNG Speaker and Microphone Gain Adjust the Speaker and Microphone arrange ToS Switch ToS Parameters Set the parameters about ToS QoS Switch Enable or disable the embed QoS service Echo Cancellation Adjust the Echo Cancellation parameters RTP Port Config Set the RTP port range STUN Parameters Set STUN server address and port if necessary 3 4 5 Line Configurations Line Configurations is used to set parameters of accounts Each line can be set one SIP account and one IAX2 accounts TUAM 8 www stephen tele com Current Configurations Basic Configurations Advanced Configurations Line2 Configurations Updating Configurations PN Configurations Provision Configurations User Management Factory Reset Rebooting System Logout EAL IRA IRA 8 Line1 Configurations SVG3
20. phen tele com enma 3 ONetworking protocol SVG300S 2 FXS Sip IAX ATA User Guide The SVG300S support several industry standard networking protocols required for voice communication and data transmission Vv yY WV SIP RFC3261 IAX IAX2 DTMF Inband RFC2833 SIP Info RTP RFC1889 RTCP RFC3605 RFC3611 DNS RFC1035 FTP RFC9590 FAX T 38 TFTP RFC1350 HTTP RFC1945 RFC2616 SNTP RFC1361 RFC2030 SNMP RFC1157 STUN RFC3489 DHCP RFC2131 RFC2132 PPPoE RFC2516 NAT RFC1631 RFC2663 L2TP OQ Support Codec Vv NV V WV G 711a PCMA G 711p G 723 G 729 Fi UR RA s www stephen tele com enma aS SVG300S 2 FXS Sip IAX ATA User Guide Hardware Parameters The IAD device hardware features Standard CPU Infineon Adm5120p Data Memory 128Mbit SDRAM Software Memory 32Mbit Flash Memories Ethernet Port 2 RJ 45 Plugs IEEE802 3 10 100 Base T Phone Connector 2 RJ 11 Types LED 5 Green LED Vv WV Power Adapter Input 100 240V Output DC 12V 1A Operating Environment gt Operating Temperature O C to 50 32 F to 122 F gt Storage Temperature 10 C 60 14 F to 140 Relative Humidity 1096 9096 non condensing Front Panel LED LED Name Power Green AN Description Successful power supply to the ATA No power supply to the ATA Link is detected at the WA
21. rator assigns your SVG300S a static IP or the DHCP function has been disabled Generally company users using LAN network use this mode please refer to Static Mode gt Ifthe network administrator has enabled the DHCP function and the phone get IP address by DHCP please refer to DHCP Mode gt Ifyou connect to the Internet directly by ADSL Most home users and company users without LAN use this mode please refer to PPPoE Mode AAA IRA 8 www stephen tele com Current Configurations Advanced Configurations Line1 Configurations Line2 Configurations Updating Configurations PN Configurations Provision Configurations User Management Factory Reset Rebooting System Logout gt Configure Static IP Enable Static Basic Configurations Network Configurations WAN Port IP Mode Static DHCP O PPPoE WAN Port IP Parameters IP Addr 182 168 1 58 Subnet Mask 255 255 255 0 Gateway DNS1 192 168 1 1 DNS2 192 168 1 4 DNS3 0 0 0 0 PPPoE Username PPPoE Password LAN Port IP Parameters IP Addr 192 168 0 1 Subnet Mask 255 255 255 0 DHCP Server Switch on DHCP Address Pool From 192 168 0 128 To 192 168 0 254 SNTP Configurations SNTP Server time nist gov user password SVG300S 2 FXS Sip IAX ATA User Guide Time Zone GNT 08 00 Beijing Hong Kong Singapore Kuala Lumpur Set
22. s PN Configurations Provision Configurations User Management Factory Reset Logout RAS www stephen tele com d SVG300S 2 FXS Sip IAX ATA User Guide Chapter 4 Update the Firmware The SVG300S uses a FTP server to download the firmware The FTP server should be ready and be able to accept connections First you need to configure the update parameters via Telnet or WEB refer to Chapter 3 O Update via Telnet Mode Configure all parameters about updating and set the value of Update flags to 1 then reboot the device e g fw setenv Use default 0 fw setenv FTP Serveraddr 192 168 0 2 fw setenv FTP Port 21 fw setenv FTP User username fw setenv FTP Password password fw setenv FTP Path update fw setenv Update flags 1 reboot Update via WEB Enter the Updating Configurations page with browser Configure all parameters about updating Set Update Option to Yes and press Apply The ATA will check new version and automatically download the firmware RAS www stephen tele com enma aS SVG300S 2 FXS Sip IAX ATA User Guide Chapter 5 Usage of the SVG300S Make a VOIP call Off hook dial the number straightly according the dialplan from services provider Wait 4 seconds or Press to send out the calling OStart a three way call Connect to the first party you wish to include in the 3 way conference Press down hook and release it fleetly After the dial tone dial and
23. t WEB and keypad access account password of the SVG300S device AAA IRA 8 SVG300S 2 FXS Sip IAX ATA User Guide www stephen tele com 5 SVG300S 2 FXS Sip IAX ATA User Guide User Management Current Configurations z User Management Basic Configurations Advanced Configurations Username root Line1 Configurations a Password Line2 Configurations L Updating Configurations Retype Password L _ PN Configurations Provision Configurations Factory Reset Rebooting System Logout 3 4 10 Factory Reset page In this page press Apply will restore all parameters to the factory default Factory Reset Factory reset will change all settings to default Are you sure Current Configurations Basic Configurations Advanced Configurations o Yes Line1 Configurations Line2 Configurations Updating Configurations PN Configurations Provision Configurations User Management Rebooting System Logout RAS www stephen tele com 5 SVG300S 2 FXS Sip IAX ATA User Guide 3 4 11 Rebooting System page After all changes have been done click Rebooting System select Yes then click Apply to restart the device Rebooting System Current Configurations The settings will take effect after rebooting the system Basic Configurations Reboot now Advanced Configurations Line1 Configurations yeEs Line2 Configurations Ono Updating Configuration
Download Pdf Manuals
Related Search