After more than 3 years and half, since summer 2006, I
Contents
1. Make sure the modules are arranged so that the current and voltage characteristics of the array are within the tolerances of the device to which the array will connect Modules sold in Europe rate up to 1000V DC 1 Jinko Solar Co Ltd LISTED East Hope Plaza 1777 Century Avenue PuDong New Area Shanghai China 200122 Tel 86 21 68 76 0266 Fax 86 21 68 76 1115 www Jinkosolar com Solar St UU JinkKO We Build Your Trust in Sun This module has a Class C Fire Rating and must be installed over a roof of appropriate fire resistance Consult your local building department to determine approved roofing materials Warning PV modules generate DC electrical energy when exposed to sunlight or other light sources Contact with electrically active parts of the module such as terminals can result in burns sparks and lethal shock a Artificially concentrated sunlight shall not be directed on the module or panel b Solar modules have a protective glass front Broken solar module glass is an electrical safety hazard electric shock and fire These modules cannot be repaired and should be replaced immediately Electric Shock and Burn Hazard This photovoltaic module produces Electricity when exposed to the sun warning c Under normal conditions a photovoltaic module is likely to experience conditions that produce more current and or voltage than reported at standard test conditions Accordingly the value of Isc and Voc mar2. not be connected together to create a voltage higher than the permitted system voltage according protection class A c PV module connect in parallel should have similar voltage Do not connect module in parallel without using connection box d Open the connection box of the control system and connect the cabled from the PV arrays to the connection box in accordance with the installation indication of the PV control systems The cross sectional area and cable connector capacity must satisfy the maximum short circuit of PV system For a single component we recommended the cross sectional area of cables is 4mm2 and the rated current of connectors is more than 10A otherwise cables and connectors will become overheating for large current Please pay attention the temperature limit of cables is 85 C and the temperature limit of connector 105 C e All module frames and mounting racks must be properly grounded in 6 Jinko Solar Co Ltd LISTED East Hope Plaza 1777 Century Avenue PuDong New Area Shanghai China 200122 Tel 86 21 68 76 0266 Fax 86 21 68 76 1115 www Jinkosolar com Solar UU JinKO We Build Your Trust in Sun accordance with local and national electrical codes Attach the equipment grounding conductor to the module frame using the hole and hardware provided Note that a stainless steel star washer is used between the ground wire and the module frame see picture below This washer is used to avoid corrosion due
3. 20A 7 43A 7 67A 7 89A Open circuit Voltage Voc 43 2V 43 5V 43 9V 44 2V 44 5V Short circuit Current Isc 7 89A 8 11A 8 30A 8 59A 8 81A Dimensions 1956x992x50mm 77 06x39 08x1 97 inch Maximum rated current series A 15A Weight kg 23 kg 50 7 lbs 10 Jinko Solar Co Ltd LISTED East Hope Plaza 1777 Century Avenue PuDong New Area Shanghai China 200122 Tel 86 21 68 76 0266 Fax 86 21 68 76 1115 www Jinkosolar com Solar tt UU JinKO We Build Your Trust in Sun Contact Jinko Solar Co Ltd Shanghai Office 12F East Hope Plaza No 1777 Century Avenue Shanghai China Postcode 200122 Tel 86 21 31268766 Fax 86 21 68761115 Jinko Solar Co Ltd Jiangxi Subsidiary No 1 Jingko Road Shangrao Economic Development Zone Jiangxi Province China Postcode 334100 Tel 86 793 8588188 Fax 86 793 8461 152 Jinko solar Import and Export co LTD Xuri District Shangrao Economic Development Zone Jiangxi Province CHINA Postcode 334100 Tel 86 793 8469699 Fax 86 793 8461152 Customer Service modulecs jinkosolar com 11 Jinko Solar Co Ltd LISTED East Hope Plaza 1777 Century Avenue PuDong New Area Shanghai China 200122 Tel 86 21 68 76 0266 Fax 86 21 68 76 1115 www Jinkosolar com
4. 205M 210M 215M 220M 225M 230M 235M 240M Maximum Power 200W 205Wp 210Wp 215Wp 220Wp 225Wp 230Wp 235Wp 240W at STC Pmax p p j P p P P P P Maximum Power Voltage Vmp 47 0V 47 2V 47 5V 47 7V 48V 48 3V 48 5V 48 8V 49V Maximum Power 4 25A 4 34A 4 42A 4 5A 4 58A 4 66A 4 74A 4 81A 4 89A Current Imp Open circuit Voltage Voc Short circuit Current Isc Dimensions 1575x1082x50mm 61 85x42 63x1 97 inch Maximum rated current series A Weight kg 22 kg 48 5 lbs 58 0V 58 3V 58 5V 58 6V 58 8V 58 9V 59 1V 59 2V 59 5V 4 55A 4 68A 4 79A 4 90A 5 01A 5 11A 5 19A 5 27A 5 35A 15A Electrical specifications of JKM240M 60Series Monocrystalline solar modules edule Type Kw JKM JKM JKM JKM JKM JKM JKM JKM oom 205M 210M 215M 220M 225M 230M 235M 240M Maximum Power 200W at STC Pmax p Maximum Power Voltage Vmp 205Wp 210Wp 215Wp 220Wp 225Wp 230Wp 235Wp 240Wp 28 8V 29 0V 29 2V 29 3V 29 5V 29 7V 29 9V 30 0V 30 2V Maximum Power Current Imp 6 94A 7 07A 7 19A 7 34A 7 46A 7 57A 7 69A 7 83A 7 95A Open circuit Voltage Voc Short circuit Current Isc Dimensions 1650x992x50mm 65 01x39 08x1 97 inch Maximum rated current series A Weight kg 19 5kg 43 Ibs 36 5V 36 6V 36 7V 36 8V 3
5. 6 9V 37 0V 37 1V 37 2V 37 3V 7 51A 7 62A 7 76A 7 85A 7 97A 8 08A 8 20A 8 31A 8 45A 15A 9 Jinko Solar Co Ltd LISTED East Hope Plaza 1777 Century Avenue PuDong New Area Shanghai China 200122 Tel 86 21 68 76 0266 Fax 86 21 68 76 1115 www Jinkosolar com Solar UU JinkO We Build Your Trust in Sun Electrical specifications of JKM230P 60Series polycrystalline solar modules JKM 2 JKM JKM JKM JKM JKM JKM Module Type OOM 205M 210M 215M 220M 225M 230M Maimu POWE at POON 205W 210W 215W 220W 225W 230W STC Pmax p P P P P P p Maximum Power Voltage 28 7V 28 8V 29V 29 1V 29 2V 29 4V 29 6V Vmp Maximum Power Current imp 6 97A TAZA T 24A 739A 7 53A 7 65A 7 18A Open circuit Voltage 36 2V 36 3V 36 4V 36 5V 36 6V 36 7V 36 8V Voc Short circuit Current Isc 7 65A 7 76A 7 88A 7 99A 8 10A 8 25A 8 35A Dimensions 1650x992x50mm 65 01x39 08x1 97 inch Maximum rated current 15A series A Weight kg 19 5 kg 43 Ibs Electrical specifications of JKM280P 72Series polycrystalline solar modules JKM JKM JKM JKM JKM Module Type 240M 250M 260M 270M 280M Maximum Power at STC Pmax 240Wp 250Wp 260Wp 270Wp 280Wp 34 4V 34 7V 35 0V 35 2V 35 5V Maximum Power Voltage Vmp Maximum Power Current Imp 6 98A 7
6. Solar tt UU JinkO We Build Your Trust in Sun Photovoltaic Module User Manual Index of Contents WU NC aria E A A A E dive lehenetsee ten 1 Applicable PROCS esiocce snitstotreniars tes itausetaunibunt cabiaiiieiaiatenbeseiunaaaunelaeridnlsdaeusteniad 1 RUTH GEMM ats sania chncieco dic tntennansu nitiesgarnaentaencdieatenee dlstansuaven isndseninesstanganuivonasedeccnanmeinee 3 Preparation before Installation cccccccsssseesessssecsssseeesssssersssseesesees 3 Installation and operation sesssssesessserrsssrrrrsrrrrtsrrrrrsrrrnrssrrnsrrrnnsrrrnnnena 4 Wiring and CONNECTION ccccsesecessseeesssseesesseeseessssseeeessneessseeseresseneesessees 6 M i te ance and CONC essnee ee aa RE aaee EEEa EEEE 7 Electrical SpecificationS ssseeeeesseerrserrrseerrrsrrrrrsrrrrrsrrrrnsnrrrnsrnnsrrtrnnsena 8 Overview Thank you very much for using Jinko Solar PV modules In order to enable the PV module to be installed correctly and to generate electric power properly please read the following operation instructions carefully before installing and using the modules Please remember that you are operating a product that generates electricity and therefore certain safety measures need to be implemented in order to avoid accidents Applicable Products This document is applicable to Jinko Solar JKM185M 72 series JKM240M 96 series JKM240M 60 series JKM230P 60 series JKM280P 72 series solar module productions
7. dule may become a falling object a am afr Pa T Mounting holes for normal installation mt For high wind and snow loads these mounting holes must also be used Figure 1 Typical pressure clamp Figure 2 Mounting and placement 4 Put the solar modules on the frame put on the screws and then combine them firmly after put on all the gaskets All the screw caps should be finished on the frame together firmly The module frame is made of anodized aluminum and therefore corrosion can occur if the module is subject to a salt water environment with contact to a rack of another type of metal Electrolys is Corrosion PVC or stainless steel washers can be placed between the solar module frame and support structure to prevent this corrosion 5 Module support structures that are to be used to support modules should be wind rated and approved for use by the appropriate local and civil codes prior to installation e When solar modules are used to charge batteries the battery must be installed in a manner which will protect the performance of the system and the safety of its users Follow the battery manufacturer s guidelines concerning installation operation and maintenance recommendations In general the battery or battery bank should be away from the main flow of people and animal traffic Select a battery site that is protected from sunlight rain snow debris and is well ventilated Most batteries generate hydrogen ga
8. ked on this module should be multiplied by 1 25 when determining component voltage ratings conductor current ratings fuse sizes and size of controls connected to the PV output d To reduce the risk of electrical shock or burns modules may be covered with an opaque material during installation to avoid shocks or burns e The installation work of the PV array can only be done under the protection of sun sheltering covers or sunshades and only qualified person can install or perform maintenance work on this module 2 Jinko Solar Co Ltd LISTED East Hope Plaza 1777 Century Avenue PuDong New Area Shanghai China 200122 Tel 86 21 68 76 0266 Fax 86 21 68 76 1115 www Jinkosolar com Solar gt JinkKO We Build Your Trust in Sun f Follow the battery manufacture s recommendations if batteries are used with module g Do not install this module to substitute even partially a roof or wall of a habitable structure h Do not artificially concentrate sunlight on modules i Do not install modules where flammable gas may be present j Do not touch live terminals with bare hands Use insulated tools for electrical connections we gt FARANI REL EAMERHLA k Do not remove any part installed by Jinko Solar or disassemble the module All instructions should be read and understood before attempting to install wire operate and maintain the module Unpacking Once the PV module has been shipped to the installation
9. ld be installed by qualified personnel only and at least by two people The system involves electricity and can be dangerous if the operators are not familiar with the appropriate safety procedures b Do not step on the module c Although modules are quite rugged the glass can be broken and the module will no longer work properly if it is dropped or hit by tools or other objects d Mounting of module 1 Module mounting must use the pre drilled mounting holes in the frame 2 The most common mounting is achieved by mounting the module using the four symmetry points close to the inner side on module frame Solar modules can be mounted using the four mounting holes located on the solar modules frame or may also be mounted using pressure clips that compress the frame from the top to the mounting rail Figure 1 The mounting rails must be run perpendicular to the length of the module 3 If excessive wind or snow loads are expected all eight mounting holes must be used Figure 2 The mounting style is the same as the style in 2 4 Jinko Solar Co Ltd LISTED East Hope Plaza 1777 Century Avenue PuDong New Area Shanghai China 200122 Tel 86 21 68 76 0266 Fax 86 21 68 76 1115 www Jinkosolar com Solar gt JinkO We Build Your Trust in Sun Improper mounting of solar modules can lead to the frame separating from the glass the glass breaking and or the solar module or component used to construct the solar cannon mo
10. s when charging which can be explosive Do not light matches or create sparks near the battery bank When a battery is installed outdoors it should 5 Jinko Solar Co Ltd LISTED East Hope Plaza 1777 Century Avenue PuDong New Area Shanghai China 200122 Tel 86 21 68 76 0266 Fax 86 21 68 76 1115 www Jinkosolar com Solar gt JinkO We Build Your Trust in Sun be placed in an insulated and ventilated battery case specifically designed for the purpose f In most applications PV modules should be installed in a location where they will receive maximum sunlight throughout the year In the Northern Hemisphere the modules should typically face south and in the Southern Hemisphere the modules should typically face north Modules facing 30 degrees away from true South or north will lose approximately 10 to 15 percent of their power output If the module faces 60 degrees away from true South or North the power loss will be 20 to 30 percent When choosing a site avoid trees buildings or obstructions which could cast shadows on the solar Wiring and connection a Before this procedure please read the operation instructions of the PV control system carefully Make wiring by Multi connecting cables between the PV modules in series or parallel connection which is determined by user s configuration requirement for system power current and voltage b PV module connected in series should have similar current Modules must
11. site all of the parts should be unpacked properly with care Caution The environment for unpacking the modules and all other apparatus should be proofed against dampness and rainfall Preparation before Installation a Visual check before installation to make sure there is no bug in the packing and junction box as well as the surface of module b Check the series number 3 Jinko Solar Co Ltd LISTED East Hope Plaza 1777 Century Avenue PuDong New Area Shanghai China 200122 Tel 86 21 68 76 0266 Fax 86 21 68 76 1115 www Jinkosolar com Solar tt UU JinKO We Build Your Trust in Sun c Check the solar cell modules with irradiance of more than 600W m and get the voltage In case the voltage is ZERO it should NOT be installed and please contact the supplier d Tools amp Material for Installation 1 Screwdriver 2 Clamp 3 For each installation hole there should be a screw M6 20 gasket and screw cap all made of stainless iron 4 The users should design and build metallic bracket for installing and bearing the weight of the PV modules The brackets are specially designed for users installation places such as the open land or on the roof of houses Caution It is recommended to place the module in a gradient angle facing the sun in order to insure maximum irradiation and also to avoid damage from flooding and other unpredictable events such as heavy impacts Installation and operation a Systems shou
12. t than rating value in uncertainty condition Accordingly the values of Isc and Voc marked on this module should be multiplied by a factor of 1 25 when determining component voltage ratings conductor current ratings fuse sizes and size of controls connected to the PV output Tables below are electrical characteristics of PV products at STC and the tolerance of Isc Voc Vmp and Imp ist10 Electrical specifications of JKM 185M 72Series Monocrystalline solar modules Module Tyoe JKM JKM JKM JKM JKM JKM a 160M 165M 170M 175M 180M 185M Maximum Power at STC Pmax 160Wp 165Wp 170Wp 175Wp 180Wp 185Wp i Maximum Power Voltage Vmp 35 0V 35 3V 35 5V 35 8V 36V 36 4V Maximum Power Current Imp 4 57A 4 67A 4 79A 4 9A 5A 5 09A Open circuit Voltage Voc 43 9V 44 1V 44 3V 44 7V 44 8V 45V Short circuit Current Isc 4 93A 5 02A 5 12A 5 23A 5 29A 5 43A Dimensions 1580x808x45mm 62 20x31 81x1 77 inch Maximum rated current series A 10A Weight kg 15 5kg 34 2 Ibs 8 Jinko Solar Co Ltd LISTED East Hope Plaza 1777 Century Avenue PuDong New Area Shanghai China 200122 Tel 86 21 68 76 0266 Fax 86 21 68 76 1115 www Jinkosolar com Solar UCU JinkKO We Build Your Trust in Sun Electrical specifications of JKM240M 96Series Monocrystalline solar modules Module Ti JKM 2 JKM JKM JKM JKM JKM JKM JKM JKM Yp 00M
13. to dissimilar metals Tighten the screw securely Ground Wire Flat Washer k Frame Figure 3 The graph of Grounding f Follow the requirements of applicable local and national electrical codes g These modules contain factory installed bypass diode if these modules are incorrectly connected to each other the bypass diodes cable or junction box may be damaged Maintenance and Care a A built up of dust or dirt on the module s front face will result in a decreased energy output Clean the panel s preferably once per annum if possible depend on site conditions using a soft cloth dry or damp as necessary b Never use abrasive material under any circumstances c Examine the PV module s for signs of deterioration Check all wiring for possible rodent damage weathering and that all connections are tight and corrosion free Check electrical leakage to ground d Check fixing screws and mounting brackets are tight adjust and tighten as necessary 7 Jinko Solar Co Ltd LISTED East Hope Plaza 1777 Century Avenue PuDong New Area Shanghai China 200122 Tel 86 21 68 76 0266 Fax 86 21 68 76 1115 www Jinkosolar com Solar tt UU JinkO We Build Your Trust in Sun Electrical specifications The module electrical rating are measured under Standard Test Conditions which are 1000W m2 irradiance with AM 1 5 spectrum and 25 deg 77 F ambient temperature The module might produce more or less voltage or curren
Download Pdf Manuals
Related Search