MULTIFUNCTION ROBOTIC AUTO VACUUM CLEANER
Contents
1. Overall Display Function Instructions 1 Toggle switch 1 Turn off 2 O Low rr 3 amp Middle I ooee 4 High signal head Near infrared transmitting head 4 Power LED Function Introduction of Space Isolator Space Isolator an accessory of the cleaner can block area by sending special infrared signal so as to prevent the Cleaner from entering some unnecessary areas Using Method amp Functional Status of Space Isolator No Name Function Information You can switch the function by sliding CD repeatedly Turn off Low 1 QDToggle switch Middle and High 1 Turn off Slide to the position then the power is off 5 L Slide to Low and turn on the power you can select the distance 2 O Low within 4m as required by infrared wall 3 Middl Slide to Middle and turn on the power you can select the distance 3 ORE within 6m as required by infrared wall 4 Hiah Slide to High and turn on the power you can select the distance 4 Hig within 8m as required by infrared wall 2 Infrared wall transmitting Slide UD then you can adjust the distance of the Space Isolator signal head Near infrared transmitting The near infrared transmitting signal makes the Cleaner run outside the head Space Isolator scope of 50 100cm without any impact to it The Power LED will flicker once every 8s until the low battery after you 4 Power LED slide to Low Middle an2. 18 CE marking states that the product is compliant to European Directives 2006 95 EC Low Voltage Directive 2004 108 EC EMC Directive It is possible to request a full copy of Declaration of compliance to the Distributor This product comply with the rules of RoHS Directive 2002 95 CE This product comply with the rules of Eup Directive 2009 125 CE 19
3. Using Method amp Functional Status of Control Panel AN the following steps are very important otherwise the remote control may fail A You should check code of the remote control or main body again while changing them after first use or maintenance B Check the remote control and main body have enough power turn off the main body press OK on the remote an control for more than 4s and then turn on the main teo o gt body without releasing OK After the Robot toots twice k PH L release OK then the code check set is finished N TTA C Ifyou fail to hear toot during the code check just repeat lt a the above process f x Function Guide Function Information START STOP Turn on the machine when you press the 7 the machine starts running when you press this key again the machine stops running Current time and week 1 Turn on the machine setting 2 When you press the time key the 9 atthe current hour flickers Press the A Y key to select the time 3 When you press the gt key the 9 at the current minute flickers Press the A Y key to select the minute 4 Then Press P keytoenter current time setting 5 you may directly press SUN MON TUE WED THU FRI or SAT to select the current week 6 After finish the setting press the OK key 7 During the setting press the Power key can cancel the setting Timing cleaning setting Cleaning week Setting And Full
4. Model XR2101 1 Rated Voltage 14 4V 2 Battery Rechargeable battery the charge time is about 5h 3 Working Hours About60 1500mA 90minutes 2200mA 4 Rated Power lt 24W 5 Operating Temperature Range 10 C 45 C 6 Operating Humidity Range lt 85RH 7 Input Voltage Current 24V 1A 8 Wireless Remote ISM Frequency Band 2 4GHz 9 Specification xb 320 x 87mm including the wheel height 10 Weight 3 2kg 11 Battery Capacity 1500mA 2200mA Technical Specifications of Remote Control Applicable Models XR2101 Rated Voltage 3V Battery 2 AAA batteries not include Remote Mode ISM Frequency Band 2 4GHz Receiving amp Transmitting Distance 210M Transmitting Power 0dB Operating Temperature Range 10 C 45 C Operating Humidity Range lt 85RH Specification 120Lx55Wx25thickness mm Weight 0 08kg Technical Specifications of Docking Station No Models Parameters Remark 1 Specification LXW XH 200 x51 102mm 2 Weight 0 23kg 3 Rated Voltage 24V 4 Operating Temperature 10 C 45 C Range 5 Operating Humidity Range lt 85RH Technical Specifications of Space Isolator No Models Parameters Remark 1 Specification LXWXH 102X71 x 106mm 2 Weight 0 14kg 3 Rated Voltage 3V 4 Battery 2 Batteries D 3V not included 4 Operating Temperature 10 C 45 C Range 5 Operating Humidity Range lt 85RH
5. b You can choose fast or slow running when cleaning use the remote controller to choose c The Cleaner will stop running in case of low battery then it will ring ten times and search the docking station for charging automatically d The Cleaner will stop cleaning if you press START STOP key CHARGE When you press the CHARGE key the indicator becomes on When the machine returns to the Docking Station to charge the indicator becomes off 1 When the machine is turned on for standby the indicator becomes on a 2 When the battery is being charged the indicator will change from dark to bright and flashes 3 When the battery is fully charged the indicator becomes normally on Parts Top of main body Handle Front bumper Infrared signal receiver Auto charging electrode Bottom of main body Ground detection sensor Battery cover Side cleaning brush So lt PAPAE Main brush Ma j Ground detection sensor Right wheel Dustbin Power switch DC socket Air outlet window Installation of Docking Station and Charging for the Cleaner Automatic recharging 1 Install the Docking Station on the flat ground firmly and against the vertical wall fixed on the wall with the docking station sticker 2 No obstacle or hollow areas 3m away from the Docking Station in the front and 0 5m on the right and left Refer to Figure 1 High Voltage Electrical hazard Pleas
6. n Pariel 2i suctus eek bd eter le han er er aes ep em bere fade 04 4 3 PONS 5 sax cesiavisext liec arx oS dead rudis ME EIE e Ur pU cmd bur 04 05 4 4 nstallation of Docking Station and Charging for the Cleaner 05 06 4 5Assembly amp Disassembly and Cleaning of Dust Bin ssseseuusus 07 08 4 6 Assembly amp Disassembly and Cleaning of Brush and Floor Brush 08 09 4 7 Assembly amp Disassembly and Cleaning of Left Right Wheel and Front Wheel 09 10 4 8Cleaning of Sensor and Infrared Transparent Window ceceeeeee seen ee es 10 5 Replacement of Ballety i ost we dero eve ont or red dut d da heb sd demote tee 10 11 6 Remote control o TOGOontTol panel cu ste ou oh rer dt ERES ee Ue ere Oe en De e ete 11 6 2Using Method amp Functional Status of Recharger ssssseuessuss 12 13 7 Auto Charging Docking Station e aao pe Ce leah od Re Ri eA He ru ta ie tate Re Teu Ese dis 14 7 1 Docking Station Display and Control Panel sessseeessees 14 7 2Using Method amp Functional Status of Docking Station sseseessesesssssse 14 B Space ISOlBlOE sors cese tiu ttt base D LU LI A LEE 15 16 9 Trouble SDOONIQ eoe oue n Eee Do Eae Rer ee MEUS a abis 16 17 10 Technical Spectli C atIOfiS osuere deett Sat pet pietre bn ee trie ewe deuten rea e tert e 18 Applicability The product mainly applicable to home hotel rooms and
7. activate the atmosphere and place in the glowing light center of the light a little essence which will give off charming aroma after heating 2 Decorative light Press the switch to turn on off while the decorative light is on switch 3 Power LED The Power LED will light when the Docking Station is connected with the power or turn off if not connected 4 Charging indicator The indicator will flicker while the recharger is connected with the cleaner 5 Signal transmitting Transmitting signal is the only way to lead the cleaner to return the Docking Station for charging so the signal transmitting position should be clean for long without any obstacle on it 6 7 Recharging The electrode and that of the Cleaner are connected to charge under contact positive amp negative mode so the position should be clean without any obstacle on it while using or electrode there will be impact to the charging 8 Charging power The power DC socket called recharger for short used to connect output terminal DC socket DC24V of the adaptor is the charging transit station between the Cleaner and adaptor so the recharger should be placed against the wall firmly and the adaptor cable should be away from the recharger or the Robot may have impact and winding during cleaning Sous essence may damage the plastic surface so please make purchase and use after consideration 14 S ace Isolator Space Isolator Display and Control Panel
8. and floor brush into the holes before closing the cover in assembly YK ra S ES AES Figure 3 Assembly amp Disassembly of Side Cleaning Brush 1 Release the screw in the main shaft of the side brush before changing the side brush 2 Press the side brush against the main shaft and then fasten the screw Refer to the figure Cleaning of Brush and Floor Brush 1 Clear the hair or big dust particles on the brush and floor brush regularly to improve the cleaning performance Clean the dust at the air intake Clean the wastepaper or small particles by dust brush directly Rotate the brush carefully and cut by scissors or pull by hand the hair yarn and other twisted objects 2 The cleaning of the brush and floor brush can be done by reference to the assembly amp disassembly Assembly amp Disassembly and Cleaning of Left Right Wheel and Front Wheel Assembly amp Disassembly and Cleaning of Left Right Wheel 1 Release the screw of the left right wheel by the screwdriver Refer to Figure 1 2 Take out the left right wheel and clean them with the brush Refer to Figure 2 Don t wash them in water 3 Place the left right wheel in the original position and tighten the screw while assembling Figure 2 A 1 2 ssembly amp Disassembly and Cleaning of Front Wheel Pull out the front wheel with your finger and tools and then clean it Refer to
9. flash gradually When the indicator becomes normally on it means the battery is charged fully See Figure 5 7 When you start the machine if the power indicator flashes it means the battery power is low You need to charge the battery See Figure 6 Figure 6 Automatic charging The main body will search the Docking Station for charging automatically in case of low battery during cleaning ns Cleaner may fail to find the Docking Station due to the obstacle decreased battery and complex condition so the Docking Station should be put in wide space as far as possible 2 When the cleaner finish cleaning the temperature of the battery is very high so charging time will be longer s Assembly amp Disassembly and Cleaning of Dust Bin 1 Extract the dust bin by r L i Figure 1 pressing the key on it e g Refer to Figure 1 and Figure 2 Assembly amp Disassembly of Dust Bin 2 Press the red button on it and then the blower will pop up automatically Refer to Figure 3 3 Reverse the blower release rS r 2 fasteners and open the I INA ex 2 cover Refer to Figure 4 um 22 E i pub NS m Figure 4 E Figure 5 and Figure 5 4 Open the bracket and the filter will appear Refer to Figure 6 5 Change a new filter press the semicircle bracket by one hand to release the fastener from the filter screen and remove the filter grid by the other hand and then change a
10. go setting 1 Turn on the machine 2 When you press the TIMER key it displays SUN MON TUE WED THU FRI or SAT 3 Press any week button or some week buttons or all week buttons you want to set timing cleaning on any day or days or everyday of a week The date of the current week flickers Cleaning time setting 4 Press the lt P key the hour Icon flickers Press the A Y key to select the timing cleaning hour you want 5 Press the lt P key again the minutes icon 88 will flicker Press the A Y key to select the time cleaning minute you want 6 After finish the setting press the OK key 7 During the setting press the Power key to cancel the setting Full go setting If your house is very big you can use Full go function full go means the cleaner go to cleaner after full charging and the cleaner go back to the docking station automatically before the cleaner s power use up BB 12 1 Press Fvti 6 the full go in the LCD screen of the remote controller will flicker 2 After finish the setting press the OK key 3 thecleaner will start cleaning automatically when the battery is charged 5 6 hours charging Remark can not use the full go function and timing function at The same time Malfunction I When you make sure the failure occurs in the case that the remote control is display within the valid scope of the remote control signal press the function key on the remot
11. small office is good for cleaning to various short haired carpet wood floor hard floor ceramic tile etc Function Introduction It is the new generation Robotic vacuum cleaner with rechargeable battery controlled by advanced intelligent program with the following function automatic vacuum cleaning mopping timing cleaning full go cleaning wireless remote control speed selection easy to use and clean Components of the cleaner Main body Remote control Recharger Adapter User Manual Docking Station sticker A Su wmv lt x amp Side brush Filter two two Space Isolator Trailing bar Mop Dust Brush F Introduction Panel Panel Function Description UV UV button START STOP To start stop cleaning CHARGE To go back to charge Power charge indicator Function Information on panel Key Operation Function Description UV This cleaner is supplied of a UV lamp which can disinfect the floor and it is especially suitable for people suffering allergy or for home with pets a Press UV can open close the UV lamp b The UV lamp will be on only the cleaner working or off when the cleaner stop to clean c The on off mode of UV lamp will be memorized automatically START STOP a Clear up gadgets or obstacles in the room before cleaning and then press START STOP key it will clean by spiral linear zigzag follow the wall modes automatically
12. MULTIFUNCTION ROBOTIC AUTO VACUUM CLEANER MODEL NO XR2101A AUTO CHARGING WITH REMOTE CONTROLLER MOP XR2101 Thank you for purchasing our new robotic vacuum cleaner XR2101 please read carefully this manual before using Safety Precautions A Caution No one else can disassemble maintain or transform the product except the maintenance technicians designated by our company or it may cause fire electric shock or personal injury Don t use other charger but the equipped one of the Robot or it may cause product damage electric shock or fire due to high voltage Don t touch high voltage power cord of the electric appliance with your wet hand or it may cause electric shock Don t bend the power cord overly or place weight on it or it may cause power cord damage fire or electric shock Don t twist your clothes or any part of your body head finger etc into the brush or wheel of the Robot or it may cause personal Don t approach cigarette lighter match and other heat objects or combustible materials such as the gasoline cleaner injury N Atten tion Don t forget to turn off the power while transporting or storing the cleaner for long or the battery may be damaged Insert the power cord of the charger well or it may cause electric shock short circuit smoking or fire Check whether the charger and socket is connected well or it may
13. backward cleaning as the arrow and it will stop after you release the key lt Turn left key Press Turn left for long the cleaner will turn counterclockwise in situ and while you release the key it will run forward as you expected Press Off to stop the cleaner It will stop automatically in case of the obstacle P gt Tum right Key Press Turn right for long the cleaner will turn counterclockwise in situ and while you release the key it will run forward as you expected Press Off to stop the cleaner It will stop automatically in case of the obstacle N 1 You should use the remote control within 10m radio signal scope or you may fail to control the main body 2 The cleaner may fail to find the docking station due to the obstacle complex condition or because the battery s power use up while you press Automatic Recharging 13 Auto Charging Docking Station Recharger Display and Control Panel Overall Display Function Instructions di vss LED decorative light a little essence can be placed above Decorative light switch Power LED Charging indicator Signal transmitting Charging positive pole Charging negative pole 8 Charging power DC socket on NOOR WD Using Method amp Functional Status of the Docking station No Function Guide Function Information 1 LED decorative Turn on the decorative light to
14. cause charging failure or even fire Remove all easily damaged objects including luminous objects fabrics glass bottles etc before using or it may cause damage to these objects or affect the using of the cleaner Please use the Cleaner cautiously in the presence of the children to avoid frightening or harming them Don t stand or sit on the Cleaner or it may cause damage to the Cleaner or personal injury Don t make the Cleaner take in water and other liquors for fear of the product damage Don t use the Cleaner outdoors or it may cause the product damage Don t use the Cleaner on small tables and chairs or other small space otherwise the Cleaner may be damaged ooo ee Don t use the Cleaner in commercial places or the Cleaner may be damaged by excessive use ground or the brush may be entangled Don t leave movable thread wire and other objects with the length of more than 150mm on the The Cleaner is not for use of the disabled people with physical or mental handicap children and those who use the Cleaner before reading the User Manual carefully ooooooe oo e P qe dv Contents o PAN DUIC EUG PTT US FUNCTION Introduction s daos te nk Lolo tto ou e Ml et Le ic d eL oie 03 Components of the PODOL s cseeencxuirce nta respi eerste dat nae voi E vua nube sat M utet 03 Introduction d Pale use ouod curando xt tL LT Ad tees I Lcd 03 4 2Function Intormallor o
15. d High and the Cleaner works normally A Open the battery bottom before using check the right positive and negative electrode and place 2x D batteries into the box correctly Pay attention to the electrode or the Space Isolator will not work resulting the damage and accident The battery consumption duration is related to the selected transmitting distance and working duration please select proper transmitting distance and low transmitting power to save the battery so don t forget to turn off the toggle switch while unused There will be some difference in the direction transmitting infrared signal of the Space Isolator and receiving distance of the Cleaner due to environmental impact and movement of the Cleaner during the actual using The difference above may vary based on the actual environment and different battery power of the Cleaner and Space Isolator 15 Installation method of Space Isolator 1 The Space Isolator is placed at the entrance to the stair or room generally 2 You can place the Space Isolator at proper position to stop the Cleaner passing through some places 3 Remove obstacles from the area you want to block in front of the Space Isolator as much as possible for fear of poor effect Ni The Space Isolator should be placed at the same level of the ground where the Cleaner is running 2 You should check whether the Cleaner can pass the Space Isolator while usi
16. e control The display will show the error code you can solve the error according the troubleshooting SPEED selection Press fast or slow key to select the fast option and slow option After the selection the machine will memorize it automatically Shutdown Cancel Stop Turn on the power switch of the machine When the display s function is in the normal status press this key to start or shut down the machine 2 When the machine is running press this key in various modes to stop the operation in the corresponding mode 3 In the timing cleaning week and time setup if the setting is incorrect or you want to stop setup press this key to delete the setting and return to the original status 4 Press this key for above 5s delete all settings and memory and return to the factory setup status OK key After finish the setting press the OK key to save the setting FULL GO After the battery is charged fully the machine will perform cleaning automatically and repeatedly CHARGE While the Cleaner is in the Standby mode or running the cleaner will search docking station for charging after you press the key While the cleaner stops running the cleaner will stop recharging after you press the key again Forward key Press Forward the Cleaner will run forward cleaning as the arrow press Off to stop It will stop automatically in case of the obstacle M Backward key Press Backward for long the cleaner will run
17. e dry your hands before usina 3 The Cleaner cannot search the Docking Station for charging if the infrared signal transmitting window of the recharger is covered 4 Connect the output terminal of the adaptor with DC socket of the Docking Station Refer to Figure 2 Pi Ca place the power cord of the adaptor along the wall or it may interfere with the brush or wheels igh Voltage Electrical azard Please dry your hands before using Manual charging 1 You can use the adaptor or Docking Station of the Cleaner to charge for the main body directly 2 Connect the output terminal of the adaptor IIN with DC socket of the main body while using the f adapter for charging Refer to Figure 1 Figure 1 High Voltage Electrical hazard 3 Barore charging connect the adaptor with he a Please dry your hands before Docking Station make sure the cleaner abut against IW S the Docking Station Refer to Figure 4 When you want to charge the machine press the CHARC key on the remote control The machine will find the Docking Station in the valid scope and charge See Figure 3 5 When the machine is searching for the Docking Station if you press the CHARGE key on the machine s panel or the power key and CHARGE key on the remote control the machine will stop searching for the Docking Station See Figure 4 Figure 4 6 After the battery s power used up the indicator will
18. intermittently 1 Check whether the set cleaning time is over Check whether there are failure codes on the display by reference of the followings The cleaner back off continuously 1 Avoid use in sunlight or dark color carpet 2 Patthe front bumper The cleaner dropped from the stair Clean the ground detection sensors at the front bottom of the cleaner The cleaner can not Auto Charging after didn t use in a long time Use the adaptor to full charged first The cleaner stop to work but no error code display Don t disassemble and maintain it by yourself contact the after sale service maintenance Failure information which may appear during using p Failure Cause How to solve E001 Ground detection sensors Clean the sensors at the front bottom of the cleaner E002 Middle brush Clean the rubbish such as hair thread wrapped on the brush E003 Power off Use the adaptor to charge after full charged then use again E004 Left amp right wheel Check the left and right wheels clean the rubbish on it E005 Dustin poor contact Check the dustbin and re fix the dustbin after cleaning If the failure still exist after the above check please contact the after sale service maintenance professional maintenance staff or the technical center of the company don t disassemble and maintain it by yourself 17 Technical Specifications
19. itive and negative poles T e correctly for fear of the damage due to wrong Hr poles Refer to Figure 2 ais SN Please take out the battery if it was unused for i A long N X WSS Figure 1 i NFigure 2 Please remember to turn off the switch before taking out the battery from the main body and virtual wall 3 Please don t place the battery in the high temperature environment above 45 C or in the water 4 Please don t exert external force to the battery or drop them from high 5 The battery should be recycled with safe disposal Please don t discard it freely or throw it into fire for fear of explosion X 1 Please don t forget to take out the battery before discarding the Robot 2 Remote control Control panel Overall Appearance Key Description Transmitting signal 1 4 Power key PK dt 2 SU Sunday Start stop key Current week Prep iur 3 Mop Monday UV key display cipis 4 JU Tuesday Time setup key Sere My 5 o amp ce Wednesday Charge key Fall qe display 6 mmer Thursday Timing key Stow cleaning 7 8 Friday Fast cleaning key Start cleaning Fast cleaning 8 s4 Saturday Auto cleaning after FULL GO 1 full charge 10 9 att all days of a week reserved 13 2 stow Slow cleaning key 14 2 3 10 OK Confirm key 4 11 A Forward key 6 12 w Backward key 5 13 lt Turn left key 7 3 9 14 Turn right key 11
20. new one Refer to Figure 7 6 Reverse the dust bin tear out the mop release the trailing bar and then unplug the right and left fasteners on the bottom of the dust bin Refer to Figure 8 and Figure 9 All parts should be assembled as before disassembly Figure 7 pmi zi a ee Figure 8 Figure 9 A Don t use the mop and trailing bar on the carpet or uneven ground Cleaning of Dust Bin and Blower 1 First dump the dust and then clean it with dust brush Refer to Figure 1 2 Pop up the blower and then clean the air inlet outlet with dust brush Refer to Figure zu 2 and Figure 3 lt 3 Don t clean the blower in water Figure 2 4 Pop up the blower take out the filter and then clean the dust bin in water Refer to Figure 4 5 Clean the filter by hairdryer or dust brush Refer to Figure 5 and Figure 6 n x PLS PL S N E 4 B a SS 6 After cleaning you can assemble it firmly SS KS as before the disassembly SSO igure 5 Figure 6 ie oa 5 6 Assembly amp Disassembly and Cleaning of Brush and Floor Brush Assembly amp Disassembly of Main Cleaning Brush and Floor Brush 1 Force the locking bar forward and raise the cover by right thumb and then raise rod of the mid cleaning brush by your left hand Refer to Figure 1 and Figure 2 2 Take out the Main cleaning brush and floor brush Refer to Figure 3 3 Insert the Main cleaning brush
21. ng it first 3 The distance between the Space Isolator and recharger should be more than 2 5m or there will be interference 4 The Docking Station should not be installed within the signal scope of the Space Isolator 16 Trouble shooting The Cleaner doesn t work or clean poorly 1 Check whether turning on the switch 2 Check whether the dustbin filter and intake are clean and whether the side brush works 3 Check whether the battery voltage declines greatly The remote control doesn t work 1 Checkthe battery status of the remote control 2 Checkthe battery status of the Robot 3 Whether check code between the remote control and main body 4 Check whether the remote control is within the available scope of the signal transmitting The Cleaner can not charge automatically 1 Check whether the adaptor is connected well with the charger and whether power LED of the recharger lighting 2 Check whether the battery power is too low if so charge the Cleaner with the adaptor directly 3 Make sure there is no barrier in front of the Docking Station 4 Usethe remote controller to let the cleaner go back to the Docking Station Increased noise in cleaning 1 Clean the dustbin and filter 2 Check whether the brush or side brush is too dirty 3 If the noise still too big you may send back the cleaner to the after sale service maintenance to add Lubricants The Cleaner stops working suddenly and rings
22. the figure Insert and press the front wheel into the right position while assembling Cleaning of Sensor and Infrared Transparent Window Clean the sensor and infrared transparent window with the cotton swab or soft cloth The wall detection sensor is in the front of the Cleaner while the ground detection sensor and infrared transparent window are in the bottom of the cleaner Refer to the figure below Please keep the transparent window clean so as to make the cleaner work better Replacement of Batter Battery replacement of the main body 1 Release the screw with the screwdriver open its base plate and then take out the battery Refer to Figure 1 and Figure 2 Please place the positive and negative poles correctly for fear of the damage due to wrong poles Please set the Cleaner in charging state to keep the best of the battery while the Cleaner is unused 10 Battery replacement of the Space Isolator 1 Release the screw with the ye ceu screwdriver and then open its base plate 2 Please place the positive and negative Electrode correctly for fear of the damage due to wrong Electrode i e e 3 The right place of battery Figure 1 Figure2 Figure 3 4 Please take out the battery if it was unused for long Battery replacement of the remote control 1 Open the battery cover and then replace the battery Refer to Figure 1 2 Please place the pos
Download Pdf Manuals
Related Search