EWK2 EWK2A
Contents
1. until the device is successfully bound Upon the successful binding pro cess EWK2 EWK2A icon Battery Level and Signal Level values will appear in ELDES Configuration Tool software s Wireless Device Management section 8 EWK2 EWK2A is ready for use AA If you are unable to bind the wireless device please restore the parameters of the wireless device to default and try again See chapter 6 Restoring Default Parameters for more details 4 PANIC BUTTON By default EWK2A keyfob supports a Panic Button feature allowing to cause an alarm at any time when the keyfob button is pressed EWK2 keyfob may support a Panic Button feature This feature that can be configured using ELDES Configuration Too software by creating a vir tual zone of Panic Silent or 24 Hour type and assigning itto Virtual Alarm option The Panic Button feature can be set up on any button of EWK2 5 BATTERY REPLACEMENT Open EWK2 EWK2A enclosure Remove the old battery from the battery slot Postition the new battery according to the appropriate battery slot positive terminal indicated Insert the battery into the battery slot Battery replaced ew See 3 INSTALLATION for more details AUAUNA Only CR2032 3V battery can be used Install only new high quality and unexpired batteries Gls Via The battery must be removed if the device is not in use EWK2 EWK2A Manual v 1 1 AUALA In order to avoid fire or explosion hazards the system must be used only with appr2. Warranty The system carries a 24 month warranty by the manufacturer ELDES UAB Warranty period starts from the day the system has been purchased by the end user The warranty is valid only if the system has been used as intended following all guidelines listed in the manual and within specified operating conditions Receipt must be kept as a proof of purchase date The warranty is voided if the system has been exposed to mechanical impact chemicals high humidity fluids corrosive and hazardous environment or other force majeure factors SAFETY INSTRUCTIONS Please read and follow these safety guidelines in order to maintain safety of operators and people around e DONOT use the system where it can be interfere with other devices and cause any potential danger e DO NOT use the system with medical devices e DONOT use the system in hazardous environment e DO NOT expose the system to high humidity chemical environment or mechanical impacts e DO NOT attempt to personally repair the system The WEEE Waste Electrical and Electronic Equipment symbol on this product see left means it must not be disposed of in household waste To prevent possible harm to human health and or the environment you must dispose of this product in an approved and environmentally safe recycling facility For further information contact your system supplier or your local waste authority Copyright ELDES UAB 2014 All rights reserved It is stric
3. and may vary 3 INSTALLATION 1 Remove the screw located on the back side of EWK2 EWK2A enclosure RT 2 Oncetheenclosure is opened remove the PCB from the EWK2 EWK2A enclosure and flip the PCB so that the back side would be facing up SE a 3 Insert the CR2032 type battery provided in the EWK2 EWK2A pack Before inserting the battery ensure that it is positioned plus marked side up EWK2 EWK2A Manual v 1 1 4 Insert the CR2032 type battery provided in the EWK2 EWK2A package Before inserting the battery ensure that it is positioned plus marked side up BATTERY CR2032 5 Insert the PCB back to the enclosure and close it Bind the device to the alarm system using ELDES Configuration Tool software Open Wireless Device Management section and enter a 8 digit wireless device ID located on the EWK2 EWK2A enclosure and press Add button see Fig No 7 The device can also be bind by sending a corresponding command via SMS message For more details please refer to the software s HELP section and ELDES alarm system installation manual Wireless Zone Tamper Alarm Quege Wireless Device Management 7 Device ID 58122812 a A es lt Back 1 5 Next gt Device Type Search Temperature Device ID Battery Level 0 0 Signal Level i Bee De 7 Press any EWK2 button press the EWK2A button several times
4. ands for failed command and feedback signal failure By default one pair of buttons is already configured to arm and disarm the alarm system It is possible to connect up to 5 EWK2 EWK2A devices to ELDES alarm system at a time The maximum wireless connection range is 150 meters in open areas 1 CONTENTS OF PACK Te iE HEV ZA een qty 1 2 CR2032 3V lithium battery qty 1 3 SEN Manta een qty 1 2 TECHNICAL SPECIFICATIONS EWK2 LED LED indicator PE ET indicator system Disarm the Panic button system Optional functionality EA 00 Optional functionality AoH Fig No 1 reflects the default EWK2 EWK2A button configuration All EWK2 keyfob buttons are EWK2A keyfob button is configu rable according to individual needs 2 WEN EWK2 EWK2A Manual v 1 1 2 1 Electrical amp Mechanical Characteristics Battery type CR2032 Lithium Battery voltage capacity 3V 240 mAh Quantity of batteries 1 Battery operation time 18 months Wireless transmitter receiver frequency 868 Mhz Range of operating temperatures 20 55 C Humidity 0 90 RH 0 40 C non condensing Dimensions 53x37x10 mm Wireless communication range Up to 30 meters in premises up to 150 meters in open areas Compatible with alarm systems ELDES Wireless This operation time can be achieved by pressing the keyfob button up to 4 times per day The operation time depends on different con ditions
5. eldes EWK 2 eldes INTET WIRELESS KEYFOB User Manual v1 1 Compatible with e ESIM264 v7 14 00 and up EWT1 v16 18 and up e ESIM364 v02 04 10 and up e EPIR2 v01 01 08 and up Main Features Alarm system arming amp disarming Panic button PGM output control Visual and audio indication of command status For more details please refer to ELDES alarm system user and installation manuals EWK2 EWK2A is a wireless device intended to remotely arm and disarm ELDES alarm system cause system alarm Panic Button or to control any electric appliance connected to the alarm system s PGM output In order to start using wireless keyfob EWK2 EWK2A it has to be bound to ELDES wireless alarm system using ELDES Configuration Too software or sending a corresponding SMS text message EWK2 keyfob features four configurable buttons intended to operate according to individual needs while EWK2A keyfob model features one con figurable button After the button is pressed EWK2 EWK2A internal buzzer s sound signal and red LED indicator confirms a transferred command to ELDES alarm system via wireless connection The status of the sent command can be checked by attempting to receive the feedback signal from the alarm system This can be performed by pressing down the same button again and holding it for 3 seconds 3 short sound signals and LED indicator flashes indicate a successfully carried out command while 1 long beep and LED indicator flash st
6. oved battery Special care must be taken when connecting positive and negative battery terminals Dispose old batteries only into special collection sites Do not charge disassemble heat or incinerate old batteries AHH The system sends an SMS message to a preset User 1 as soon as the battery level runs below 5 eyes The battery status can be monitored in real time using ELDES Configuration Tool software 6 RESTORING DEFAULT PARAMETERS EWK2 1 Press and hold and buttons simultaneously 2 Hold the buttons pressed until LED indicator and the buzzer provide several short flashes and beeps simultaneously 3 Release the buttons 4 Parameters restored to default EWK2A 1 Press and hold the lower side of the button 2 Hold the button pressed until LED indicator and the buzzer provide several short flashes and beeps simultaneously 3 Release the button 4 Parameters restored to default 7 ADDITIONAL INFORMATION Limited Liability The buyer must agree that the system will reduce the risk of fire theft burglary or other dangers but does not guarantee against such events ELDES UAB will not take any responsibility regarding personal or property or revenue loss while using the system ELDES UAB liability according to local laws does not exceed value of the purchased system ELDES UAB is not affiliated with any of the cellular provi ders therefore is not responsible for the quality of cellular service Manufacturer
7. tly forbidden to copy and distribute information in this document or pass to a third party without an advanced written authorization from ELDES UAB ELDES UAB reserves the right to update or modify this document and or relat ed products without a warning Hereby ELDES UAB declares that the wireless keyfob EWK2 EWK2A in compliance with the essential requirements and other relevant provisions of Directive 1999 5 EC The declaration of conformity may be consulted at www eldes It EWK2 EWK2A Manual v 1 1 Made in the European Union www eldes lt
Download Pdf Manuals
Related Search