Home

Ultimaker Original User Manual

1. age prepares your 5D model into instructions that your Ultimaker uses to produce an object 1 The Cura software package can be downloaded from the Our software section on our website www ultimaker com pages our software 2 Download the latest version of Cura for your operating system Our software Is available for WindowsXP or newer MacOS 10 6 or newer and Ubuntu Linux 12 10 mw amp Ay 3 Open the installer and follow the directions to install the software 4 After the installation the configura E Cura 14 07 Setup eel tion and calibration wizard will run Choose Install Location Choose the folder in which to install Cura 14 07 Setup will install Cura 14 07 in the following folder To install in a different folder dick Browse and select another folder Click Next to continue Destination Folder IC Program Files x36 Cura 14 07 Space required 86 2MB Space available 383 3GB NOTE We keep on updating our software so the latest version that you have downloaded might be a newer version than the one in this manual This should have no impact on the installation procedure B1 Downloading and installing Cura First use of your Ultimaker Original B2 The first run wizard This chapter guides you through the steps and the first run of the Ultimaker Original After you switeh on your Ultimaker Original lets install Cura and make your 3D printer print ready 1 When you start Cur
2. A visual check is recommended to see if there is not any Old prints objects on the build plate Make sure no one can walk over damage or pull out the power supply cable Updating firmware with USB cable Every once in a while Cura will give you a notification that new firmware is availa ble New firmware means that we have optimised the control of the electronics which results in better print results and user experience If you see this notification connect the USB cable between your computer and your Ultimaker Original and follow the instructions in Cura El In general Maintenance for your Ultimaker Original 2 E2 The build plate Note If you have a Heated Bed installed go to E3 After a lot of printing The blue tape can get torn or worn down This can cause an uneven print surface and It is recommended to replace it once a while 1 Turn off the machine and wait for the printhead to cool down so you won t burn your hands on a hot printhead 2 Now carefully oush slide the plexiglass plate out of its clamp system 3 Reapply tape to either the whole build plate or just part of it and carefully oush slide the plate back 4 After removeing the buildplate re check if the calibration is still right E2 The build plate Maintenance for your Ultimaker Original 28 ES The Heated build plate After a lot of printing The glass plate can get a little bit dirty and the excess glue needs to be clean
3. Share on YouMagine com Through this button you can share your 3D files on YouMagine 4 Menu bar In this bar you can change to Full settings preferences and more expert settings 11 12 5 Print type profiles 5 options to choose a print profile 6 Material settings 2 different settings in material 7 Material Diameter If you buy Ultimaker filament the default value is 2 85mm 8 Print with support struc ture The option to give your model some support material to make the print more successfull 9 View modes After your model has been orepared for printing you can use different view modes to analyse your design C1 Cura software interface Make a printfile with Cura software 10 Rotate model options Option to change the rotation of the object you would like to orint 11 Scale model options Option to change the scale of the object you would like to orint 12 Mirror model options Options to mirror the object you d like to print 13 Loaded 3D model This is the object you have loaded through the load file button 14 3D print volume This is a visualisation of the orint area of your Ultimaker C2 Cura mouse interface The following mouse actions are used to work navigate and view the 3D model Scrollwheel button Use the scroll wheel to zoom Leftmouse button Select objects Hold and move the mouse to drag In or out object on the 3D print area Rightmouse b
4. Y endstop Communication State Operational Head temperature 102 11 Now do the same with side back Y endstop Communication State Operational Head temperature 102 12 Next step is to click the top Zend stop pete pz rotate the build plate screw or click it with your diente screw driver finger 13 When Cura asks you to click the bottom bse pres the bonom Z endstop use the hex screw driver to touch Hena temperare 102 and click it B2 The first run wizard First use of your Ultimaker Original N zz A If the build plate is too far away from the nozzle your 3D print might not stick to the build plate Equally if you adjust the build plate too close to the nozzle the bulld plate can block the filament from extruding from the nozzle NOTE If you have a heated bed installed follow steps 14a to 18a 14 In this step Cura will help you to level your PA Bed leveling wizard printbed Make gure you choose the This wizard will help you in leveling your printer bed Connect to printer button to perform this e to and let you adjust the height of the bed to the nozzle action Print a line around the bed to check if it is level Connect to printer 15 The printhead should have moved to its ho ming position in the front left corner The print bed should have moved up almost or against the nozzle Use the Hex screwdriver and a standard A4 piece of paper to level you
5. YouMagine for fun projects and free printable models www youmagine com Happy building and printing and we ll be in touch Team Ultimaker Support We would love to hear from you We are easy to reach and enjoy answering all your questions Technical assistance sales enquiries or general information we are there for you Find the infor mation below to contact us General info ultimaker com Support support ultimaker com Sales sales ultimaker com Marketing PR pr ultimaker com Phone 31 0 345712017 Meet us online at go A1 The Ultimaker experience Original Introduction amp Specification A2 Specification of the Ultimaker Original Printing Print technology Build volume Layer resolution Position precision Filament diameter Nozzle diameter Print soeed Travel speed Software Software package File types Supports Connectivity Physical dimensions Frame Dimension Fused filament fabrication FFF 21x 21x 20 5 cm Ultra high 20 micron High 60 micron Medium 100 micron Low 200 micron X 12 5 micron Y 12 5 micron Z 1 875 micron 2 85 mm generally known as 3 mm filament 0 4 mm 30 mm 1 300 mm s 30 mm 1 350 mm s Cura Official Ultimaker STL OBJ DAE AMF Windows XP 32 bit 7 Ubuntu Linux 12 044 Mac OS X 10 6 64bit Stand alone printing from SD card USB firmware ADO CM Y 34 2 cm Z 38 8 cm Operating dimension with UltiController spoolholder and the m
6. bed Slide the pa per back and forth between the nozzle of the printhead and build plate as you screw or un screw with the screwdriver 16 Make sure you feel a little bit of friction from the paper sliding between nozzle and build plate 17 When you are finished with this corner select the Resume button in cura This will move the head to the next corner Repeat this step for all corners 18 Follow the instructions when you have mate Hs Bed leveling wizard ral Inserted your Ultimaker Original you should This wizard will help you in leveling your printer bed select the Resume button again and now your yn do me he Move the printer head to each corner and let you adjust the height of the bed to the nozzle Ultimaker orinthead will heat Up and print a Print a line around the bed to check if it is level square in lines to show and check that your build Serestoprimer plate is level and the material sticks to the tape If the build plate is too far away from the nozzle your 3D print might not stick to the build plate Equally if you adjust the build plate too close to the nozzle the build plate can block the filament from extruding from the nozzle 14a In this step Cura will helo you to level your orintoed Make sure you choose the Connect to printer button to perform this EE ve d ct on Move the printer head to each corner and let you adjust the height of the bed to
7. pull it outwards this gives you a better view how to get your filament into the material feeder 3 Now take the filament wire and guide it up wards between the two wooden plates and up through the coupling 4 Make sure you push the filament all the way through to the end of the bowdentube untill you can t move it any further 5 Now rotate the black feeder part back into place Apply some pressure so the lever can be pushed back down 6 Now you can easily rotate the black lever back so that the material feeder places the right amount of pressure on the filament B3 The first run wizard Installing the fillament MAKE A PRINT FILE WITH CURA SOFTWARE C1 Cura software interface This is the main screen of Cura Here you can choose which object or objects to orint And how you want them to be printed 4 1 o 4 C Fast low quality print Material PLA O AB Diameter Eos 4 Other support structure 2 3 i quickprint profile C High quality print i Ne val quality print y ry X a A 530 MIS OF4Simetem4ignam ad A 10 Load file Click this button to load an object to your print area You can add as many objects as you can fit on the plate 2 Save print toolpath When you press this button the prepared toolpath will be Saved on your drive or SD card It can also be printed directly if a usbcable is connected 3
8. A houro 23 mint tes AMAS SN EJE NOTE The screenshots may not look and work exactly the same because this platform is in continuous development C3 From YouMagine com to load file in Cura Make a printfile with Cura software 18 C4 Preparing a 3D model 1 Most 3D printable files that you will find on YouMagine com are in the STL format Let s start by clicking the Load button in Cura 2 When you have loaded a file into Cura you might notice the progress bar Cura will automatically start making the 5D mo Se ae a del print ready for you 3 Inthe meantime you can adjust settings and select a print type Other 4 When the 3D model is prepared the Save toolpath button pops up and gives you the option to save the prepared model ina directory Underneath the button Cura gives you an indication about your print on Estimated print time Amount of material required The weight of your 3D print Othe l ZAiminuites Print support structure ELS Meer 5 giai 5 After you insert the included SD card into your computer Cura changes the Save toolpath Button into the Toolpath to SD Button 6 Just after you choose the Toolpath to SD button the progress bar will run again but now it will save the file on the SD card 7 When cura has finished saving the file it will give you the notification that your file has been saved Saved as E UltimakerRobot su
9. Original Ultimaker The fast easy to use Open source 3D printer User manual English Version 1 1 Ultimaker Table of Contents A Welcome to the Ultimaker Original Al The Ultimaker experience A2 Specifications of the Ultimaker Original B First use of your Ultimaker Original B1 Downloading and installing Cura B2 The first run wizard B3 Installing filament G Make a print file with Cura software C1 Cura software interface C2 Cura mouse interface C3 From YouMagine com to load file in Cura C4 Preparing a 3D model C5 From SD card to print your file D Use of the Ultimaker controller display DI At first sight D2 Navigation and basic functionalities D3 Use of the controller during printing E Maintenance for your Ultimaker Original El In General E2 The build plate ES The Heated build plate E4 Cleaning the material feeder E5 Lubricating the axes F Terminology Fl Terminology Table of content User manual 99 WELCOME TO THE ULTIMAKER ORIGINAL AT Introduction amp Specification Dear customer Thank you for purchasing the Ultimaker Original Kit This user manual will guide you through the setup and printing process step by step Available online www ultimaker com pages support manuals There s also a wealth of information tips tricks and amazing Ultimaker printed objects on our online community forum Drop by and say hello www ultimaker com forum Visit
10. a 5 e oe mR me a es a an A Oh e gt _ al A A A e Es a os D a Y gt y e gt er a os gt gt zier S es yo ae wr zur a a A az T A 1 Push wheel You can navigate through the display by using the button This button can be pushed and rotated By rotating you can select or control an action By pushing you can confirm an action When pushing the button you hear a beep sound to confirm your chosen action 2 Nozzle temperature Target temperature The first temperature Oe 4 shows the nozzle s current temperature the second temperature 000 is the target temperature For example when preheating the target becomes 024 210 3 FeedRate This is the print speed of your machine You can change this by rotating the pushwheel Number 1 Its recommended you leave this value on 100 especially when you are not an experianced user 4 SD card indication The note Card inserted is obvious it means your SD card is ins erted and is accessible When you remove the card by pushing it the menu will read Card removed 5 Print process indication OOO SD keeps track of how far you are into you print 000 means you haven t started 100 means you print is finished 6 Height 3D model This shows you how much the z has moved down Optional 7 Heated bed temperature Target temperature The first temperature De0 shows the nozzle s current temperature the second tem
11. a for the first time Make sure you follow the configuration wizard Select Ultimaker Original as vour printer Also dese lect the check box if you do not agree with us checking your slicer profiles Cura 13 02 or newer can collect user statistics These sta tistics are gathered to improve next version of Cura and Select your machine possibly provide more features for Ultimaker and RepRap Ee users The collected information includes profile settings Ultmaker Original and machine types ae lt does NOT collect usernames models or any privacy Other Ex RepRap MakerBot Witbox sensitive information Currently these stats are only eS amg ang eneen er a On This does NOT submit your models online nor gathers any privacy related information collected and there is nothing done with it yet We want Submit anonymous usage information to make these stats quite open for everyone to use as well Seinen menes as the option to share this information or not 2 Leave the first check box selected if you Select upgraded parts you have have a new Ultimaker Original If not make sure Gre woudike to know which upgrades you have in your machine you check the date of purchase of your Bee Ultimaker Any of the other checkboxes can be es modified later Hit the Next gt button Extruder drive upgrade IF you do not have fis upgrade itis highly recommended to improve reliability This upgrade can be bought from the Ult
12. ax height filament guide tube X 54 4 cm Y 34 2 cm LIO EM Temperature Ambient Operating Temperature 15 52 C Storage Temperature 0 52 C Operating nozzle temperature 180 260 Operating Bed temperature 50 110 Electrical AC INPUT 100 240 V 2 0 AMPS 50 60 HZ 120 watt max Power Requirements 19V DC 6 52 AMPS Electrical with heated bed AC INPUT 100 240 V 4 0 AMPS 50 60 HZ 221 watt max Power Requirements 2AV DC O 9 2 AMPS WARNING The Ultimaker Original generates high temperatures and has hot moving parts that can cause injury Never reach inside of the Ultimaker Original while it is in operation Always control the Ultimaker Original from the push wheel on the UltiController or with the power switch on the back Allow the Ultimaker Original to cool down for at least 5 minutes before reaching inside CAUTION When opening the Ultimaker Original for service ensure that the power supply is turned off and the cord is disconnected from the wall socket CAUTION Only use the power supply provided with your Ultimaker Original A2 The Ultimaker experience Specification of the Ultimaker Original FIRST USE OF YOUR ULTIMAKER ORIGINAL B1 Downloading and installing Cura Before we start using the Ultimaker Original we need to install the soft ware to calibrate the machine The preferred software for your Ultimaker Original is Cura developed at Ultimaker This software pack
13. controller display 24 D3 Use of the controller during printing You can start a print by navigating to Print from SD gt and clicking one of the filena mes his will start a print If your hot end is not heated yet it will first start heating your hot end to approximately 210 C Next it will load the data and start your print When a print has been initiated one option in the menu will change Instead of prepare gt you will find it to be named Tune gt In the tune menu you can live tune your printer Meaning you can change parameters of the print process while printing Speed The speed you are printing in will increase decrease Changing the speed can be done faster by just rotating the wheel in your home menu If you change the speed it will have effect on the perimeter infill and travel soeed Nozzle With Nozzle you have the option to change the temperature of your hot end Bed With Bed you have the option to change the temperature of your heated bed Fan Speed You can change the speed of your fan from 0 255 But in thehe slicer you can set more eleborate modes for example if you want the fan on off or with an interval Flow Flow allows you to increase or decrease the amount of filament that is being extruded This can be interesting when you are over or underextruding with the current settings However the first thing you should do is check if you have entered the right diameter of your filament in your slic
14. ed off It is recommended to do this every once in a while 1 Turn off the machine and wait for the printhead and printbed to cool down so you won t burn your hands 2 Now carefully move the glass retainer clips all the way to the side use a screw driver as leverage 3 To take the glass plate out of the machine move the front a little bit Uowards and then pull it towards you 4 Clean the glass plate using some dishwashing soap and water 4 Reinsert the glass plate and do a quick check if the platform is still level E3 The Heated build plate Maintenance for your Ultimaker Original 29 E4 Cleaning the material feeder Note The drive might look different for your machine In the Ultimaker material feeder sits a knurled bolt This bolt grips the filament and can so metimes get clogged because the feeder is a bit dirty Then the material will start to slip You clean its as follow 1 First pull the black lever Upwards and open the material feeder 2 Then take off the little clio that holds the filament gear in place 3 Now you can take out the bigger wheel with the dirty knurled bolt You can blow against it or use a brush the clean the bolt Reverse the previous steps to re assemble the feeder 50 E5 Lubricating the axes Z Axes Approximately every half year the threaded rod on the z stage has to be lubricated A green gre ase Magnalube G is supplied with the Ultima ker Original This g
15. er An inaccurate value may result in the same complains Change filament This function allows you to change filament during printing The print bed will lower the printhead will move to side and the extruder will retract the filament Now you can open the material feeder and replace it with new filament Make sure to push the filament all the way through the bowden tube untill it exits through the nozzle now press the pushwheel on the UltiController to continiue the print Common workflow with the UltiController A common workflow with a well calibrated Ultimaker Original is saving a sliced model on your SD card with Cura Cura set to Ultimaker Original machine settings Safetly remove the SD card and insert the SD card in your UltiController From the first screen click the button navigate to Print from SD and select a file you want to print After heating up the print should start When you do not use your UltiController it automaticly reverts back to the first screen in approximately 15 seconds where you can watch the state of the print D3 Use of the controller during printing Use of the Ultimaker controller display 25 MAIN TENANCE FOR YOUR ULTIMAKER ORIGINAL E1 In General To achieve the best results from your Ultimaker Original some basic maintenance is recommended This chapter contains tips which helps you to keep the Ultimaker Original running at It s best Before you make a print a quick check is advised
16. imaker webshop or found on thingiverse as thing 26094 3 First Plugin the USB cabel then press the Configuration Wizard P y Upgrade Ultimaker Firmware U Dg ra d e to M a rl n fi rmwa re D U tto A to m a ke Firmware is the piece of software running directly on your 3D printer f This firmware controls the step motors regulates the temperature sure you have the latest firmware running on e your Ultimaker This should take about a maxi isc ioe eas Aa alaba ale ng mum time of 20 seconds When its finished hit cura requires these new features and thus i pario o daa the Next gt button sc upgrade Do not upgrade to this firmware if You have an older machine based on ATMega1280 Rev 1 machine Have other changes in the firmware e00 Firmware install for Ultimaker Original 1 Uploading firmware B2 The first run wizard First use of your Ultimaker Original NOTE Some steps during the endstop checks may be different if you have an Ultima ker Original 4 In the next configuration steps we want to do some check ups on your Ultimaker Original Make sure before doing these checks you Nave Connected the usb cable The printhead is in the middle of the frame 1 The build plate has some distance from the nozzle minimal 3 cm 2 NOTE with the Heated bed the build plate might look different the checks are still the same 5 Please select the Run Checks function Ultimaker Check
17. ment as soon as it is put onto the build plate Push button By rotating and pushing the button in front of the Ultimaker Original you can access the control panel SD card Secure Digital memory card that can store digital data The card that can be used with the Ulti maker has to be an SD card and not an SDHC card It has to be formatted with FAT16 or FAT 52 Slicing The process that turns a 3D model into code that can be used with 3D printers Slider blocks The slider blocks maintain the connec tion between the gantry axes Spool holder The wooden piece attached to the back of the Ultimaker Original lt can hold different kinds of filament spools Stl A widely used file format for 5D models Threaded rod The long rod behind the build plate which is threaded This rod moves the build platform up and down USB cable The cable that allows direct communi cation between the Ultimaker and a computer using the USB interface on the computer YouMagine com A website where you can share your models and download 3D models from the people within the YouMagine communnity oO NOTES 54 Ultimaker Ultimaker B V Burgemeester R vd Venlaan 11 4191PL Geldermalsen Support ultimaker com The Netherlands Ultimaker com
18. perature 000 is the target temperature For example when preheating the target becomes 020 65 D1 At first sight Use of the Ultimaker controller display 22 D2 Navigation and basic functionalities 1 When pressing down on the push wheel you will be presented with the follo wing screen where see the main menu of the controller The arrow in front of all the functions indicate s whats selected y ES P RS 1 When you have selected Info screen this could also be named Watch and push down on the wheel you navigate back to the first screen 2 Via gt Prepare gt you will proceed to the next sub menu where you can find a variety of settings that can be used to prepare your Ultimaker Original Disable steppers With this function you will disable the steppers This allows you to move the printhead and printbed without the motor resistance Auto home With auto home you sent the printhead to the auto home position The home position Is in the front left Set origin Set origin will make your current position the 0 0 0 home position Optional Howe Z This allows you to move the Z stage up or down by turning the con troller knob Preheat PLA With Preheat PLA your hot end will heat up to 210 C Preheat ABS With Preheat ABS your hot end will heat up to 240 C Cooldoun With Cooldown the temperature will drop to room temperature Move Axis With Move axis you will open another sub menu which allows you to mo
19. pport g 8 Before taking out the SD card make sure you always choose the safely eject button in Cura C4 Preparing a 3D model Make a printfile with Cura software 19 C5 From SD card to print your file 1 After saving the file and safely ejecting your SD card from your computer It is time to insert it in the SD card Slot at the side of your UltiController 25 A 2 By navigating to card menu and chosing a file on the sd card you press the button and your object will start printing C5 From SD card to print your file Make a printfile with Cura software 20 USE OF THE ULTIMAKER CONTROLLER DISPLAY D1 At first sight When switching on the Ultimaker the main thing you will notice Is that the display lights up You instantly get the mainscreen of the controller as shown in the image bellow First lets explain what you see and their functionalities ex o mt E ost es Mies Y AFA gt 9 se ats s 5 sk A ss un s YA a O ws a a ae Vane DE Jess Art wo u 3 x s a g d di a sa S Sos A gt s A a er a a va s sos zi a a a Died ye a Pe s eS a 5 ga A A 1 oa 4 os tes 5 id x p MAY s ony y Ke fi ss Y gt ss 4 Pe ont Sg x a Pr e Ke gt de qe ar e nn p ee g 2 e A Y Bas Er gt gt gt Ga f Era 1 at LAS t a CALLS SC e Ne gt a i gt A Asie rn ash pr 5 bs Wiss a us J eo Daa e hed gt PS ms Ye j y a A Oe ge
20. re The software that runs on the electronic board Gantry The construction of metal rods that allow movements on the x y and Z axis G code The code that comes out of the slicing pro cess of a 3D model in Cura It describes the move ments of your print head Knurled Bolt Gives grip to push the filament in the filament guide tube Material feeder The feeder that drives the filament through the filament guide tube into the heater Material feeder tensioner The tension with which the filament is pushed through material feeder can be adjusted by tuning this tensioner Nozzle The opening at the end of the print head The filament gets pushed through the opening and will deposited on your build plate PLA filament This is a hard bioplastic that has a low environmental impact It is derived from renewable Starch based resources It has a very low shrinkage which is helpful for large prints F1 Terminology Terminologyfor the Ultimaker Original Build plate screws These screws can adjust the leveling of the build plate Power supply The A C power supply It consists of a block and a power cable The cable can have different power plugs US EU AU UK It depends on what kind of electric outlet is used in a country Power switch Turns the Ultimaker on or off Print head The assembly that melts the filament while the material is pushed through the nozzle onto the build plate Print head fan The fan which cools the fila
21. rease is the lubrication which has to be used only on the threaded Z stage rod Note the green grease should be applied as shown in the photograph Make sure you spread 10 drops of grease over the entire exposed threaded rod With you next print on the Ultimaker Original the Thread will grease itself by moving up and down X Y Axes If you notice small waves in the outside surfaces of your 3D printed objects t is recommended to add a single drop of sewing machine oil onto the X and Y steel axes rods This will improve the smooth movement of your Ultimaker Original This lubrication is not included in the Ultimaker Original package If you choose to lubricate the X and Y axes you MUST use sewing machine oil Apply a maxi mum of one droplet oil on the axis and move the orint head around to spread the oil across the rods Afterwards remove any excess oll E5 Lubricating the axes Maintenance for your Ultimaker Original 5 TERMINOLOGY ULTIMAKER ORIGINAL F1 Terminology ABS filament This is a well known plastic known for its strength and industrial properties Build plate The frame that supports the plexiglass print plate Cura Open Source Software that allows you to turn your 3D model into a printable file Display The LCD display provides the menu for con trolling the Ultimaker Original Filament guide tube The plastic tube that guides the filament from the material feeder to the print head Firmwa
22. the nozzle Print a line around the bed to check if it is level 15a The printhead should have moved to Its ho ming position in the front left corner The print ia bed should have moved up almost or against re the nozzle PAP Use the buttons Up 0 2mm or Up 10mm to move Use the up down buttons to the platform up to the nozzel Make sure the e Z switch is triggered The Up buttons don t work if the switch is triggerd Bed leveling wizard This wizard will help you in leveling your printer bed 16a Press Resume and the bed will move up to the Z switch trigger position Now use the thumbscrew in the left corner to move the bed up or down so it Is just touching the nozzle 17a When you are finished with this corner se lect the Resume button in cura This will move the head to the next corner Repeat this step for all corners 18a Follow the instructions when you have 7 material inserted your Ultimaker Original you ae should select the Resume button again and and let you adjust the height of the bed to the nozzle now your Ultimaker printhead will heat up and Ardara cana print a square in lines to show and check that your build plate is level and the material sticks to the tape Ez Connect to printer B3 Installing filament and the spoolholder 1 First rotate the the small black lever vertically then pull it all the way up 2 Now take the black feeder part and
23. up It is a good idea to do a few sanity checks now on your Ultimaker Now Cura connects with the electronics and en functional tests some of the internal communication ee Temperature Eene Cura will also perform a temperature check to Ultimaker Checkup ie a s It is a good idea to do a few sanity checks now on your Ultimaker S a f t fu N ct O N S CO r re C 0 y You ER skip these if you know ea machine is dal Run checks Skip checks Communication Y Temperature Endstops Communication State Operational Head temperature 27 6 After the temperature check has finished Cura A Please press the right x enastop Communication State Operational will check your end stops End stops determine eaa temperature 67 the maximum motion size Make sure that you move the printhead in the direction of every indicated end stop 7 When the wizard asks you to check on the right front switch x axis gently move the print head in this direction till you here a click and Cura gives you the next command B2 The first run wizard First use of your Ultimaker Original 10 8 If the printhead can t touch the end stop don t force it Unscrew the end stop with the hex screwdriver and move it a bit inwards the frame as Indicated on the image 9 Move the printhead to the left corner untill S Communication State Operational you hear a click Head temperature 102 10 Now do the same with side front
24. utton Rightmouse button Hold and move the mouse to Shift rotate the viewpoint around Hold and move the mouse to the 3D model pan the 3D view Right and left mouse button Hold and move the mouse to ZOOM C2 Cura mouse interface Make a printfile with Cura software C3 From YouMagine com to Cura Now that you are familiar with Cura we continue to explain how you can download a SD file from YouMagine com and load this into Cura YouMagine com is an online community for 3D printing 1 Open your browser and go to www youmagine com 2 Use the search field at the menu bar next to the magnifying glass to find a model of your interest Let s search for example coffee cup and Enter 3 Choose a design you like 4 The following page will provide you with a Download button where you can get your stl file which is needed to print a 3D model 5 The stl file can be loaded into the Cura software this will be explained more fully in the next chapter Tip If you ve made a 3D design yourself you can contribute back to the YouMagine commu nity amp Yo U MAG N E Ideas Discover Desi igners Sign up Sign in Discover Featured NachoKaoS 1 DanielNoree Miniatures Other Coffee Cup by NachoKaoS Download 1 3 MB Send to 3D printer ON NM Select a quickprint profile J High quality print j TY Y e Normal quality print Ar M _ Fast low quality print A
25. ve your axis around You can move the X Y Z and E extruder motor by clicking on the X Y Z and E in the menu and rotate your button Extruding will only work when your print head is at least 180 C D2 Navigation and basics functionalities Use of the Ultimaker controller display 25 3 When you have selected Control you will proceed to the next sub menu where you will find a variety of settings that can be used to control your Ultimaker Original Temperature In this sub menu you can change several settings that influence the tempe rature of your Ultimaker Here you can change the nozzle and bed temperature and fanspeed lotion Only make changes in the Motion menu if you know what you are doing More can be found at our wiki page http wiki ultimaker com Store memory Save the settings you have changed in the control menu Load memory If you ever made and saves any changes in the settings this option allows you to load them Restory failsafe Restore failsafe will reset your UltiController to its Original settings All the settings you previously changed will be deleted Firmware version Here you can see what the current firmware version is on your Ultima ker Original 4 When there is no card inserted this function will indicate Ma Card When you have selected Print from SD you will access a sub menu where all the Gcodes on your SD card will be visible D2 Navigation and basics functionalities Use of the Ultimaker

Ultimaker Original User Manual

Contents

Download Pdf Manuals

Related Search

Related Contents