ROSETTA - Crem International
Contents
1. Place the steam wand over the drip tray and Immerse the steam wand with temperature press the steam button this will allow condensed sensor into the jug containing the milk make water to be ejected Turn it off again when only sure the wand tip is submerged steam comes out by pressing the button again a a Press the button again to start heating or frothing the milk WARNING Do not remove the steam wand from the jug whilst the steam lever is open Doing so may result in scalding and serious injury After the process is finished position the steam wand over the drip tray and press the steam button to clean leftovers of milk in the wand Turn off the steam after a few seconds by pressing the button again clean the outside of the steam wand with a damp cloth to prevent nozzle blockage Once the milk reaches the programmed temperature the steaming will stop automatically and you may remove the jug ca j2. To access the counters menu go to the start of the second menu level Count A see fig 07 Briefly press the Continuous Dispensing button to display the fig 12 counters option see fig 12 The machine has the following 4 counters Litres volume of water dispensed by the machine indicator used for descaler maintenance cycles Service number of coffees dispensed indicator used for servicing Number of coffees infusions dispensed Number of coffees dispensed per button Flow meter Time out alarm Boiler filling up Probe unconnect Service 999999999 Change filter 999999999 Fault in flow meter X Flow fault detected in counter X Check that the machine is receiving water Temperature sensor fault Service the machine To disable the alarm and reset the counter Turn off the machine Simultaneously press and hold down the Short Espresso and Long Espresso buttons Turn on the machine Regenerate the filter To disable the alarm and reset the counter Turn off the machine Simultaneously press and hold down the 2 Short Espressos 69 and 2 Long Espressos 69 buttons Turn on the machine m If boiler filling time exceeds the programmed time 2 minutes all of the Drink buttons lights will flash and the machine will be disabled To re enable it turn the machine off and on again at the power switch If the electronic control panel does not receive a pul
3. Between and 8 seconds Enables Continuous Dispensing press again to disable Over 8 seconds Access coffee dose programming menu see below Machines not equipped with display Under 4 seconds Enables Continuous Dispensing press again to disable Over 4 seconds Access coffee dose programming menu see below To activate these functions turn off the machine at the power switch then while holding down the required button on the left hand Drink buttons turn the machine back on LI I Short Espresso Enable electronic pre infusion LI I Long Espresso Disable electronic pre infusion LI 69 2 Short Espressos Perform auto cleaning LI eS 2 Long Espressos Turn on off flashing of button lights only available on MINI machines Note In machines equipped with a display electronic pre infusion may have to be enabled disabled from the service programming menu 25 li PROGRAMMING M J Programming the coffee dosage 110 This section explains how to program the doses dispensed automatically by the drink buttons A Important Use a porta filter filled with fresh coffee for every new dose you program On machines not equipped with a display hold down the Continuous Dispensing button for 4 seconds On machines equipped with a display hold down the Continuous Dispensing button for 8 seconds The Continuous Dispensing button light will flash On machines equipped with a display all of the Drink butto
4. Rinsing the capsule group Cleaning the capsule group Disassemble the group gasket Cleaning the Group Gasket and Capsule Holder Reassembling the Group Gasket Removing the adjustable spout Cleaning the adjustable spout Additional handling Of chesmachimesisaicssissecsssssasssasisesessassaostascsssesiassvsessseessannssesedeadehaesgnssedensasindesungentzanbsscndyisayensanneseaebs STORAGE AND DISPOSAL OF MACHINE How to store the machine Disposaliof machhe e i NEE A ENE EE PROGRAMMING siminer aeina nir eia E EEES 25 Buttons functions Additonal button functions Programming the coffee dosage Programming the hot water dosage Programming the turbo steamer PROGRAMMING USING THE DISPLAY Machine status Accessing the second menu level Setting the clock hours minutes and day Auto on off Counters MESSAGESANDALAR MS seats sccsusssztescssnnebssatessesen sien ssanninaleenuienpedeunenoniten necitta nensterasideensiuasies 31 TROUBLE SEIC TIN EEEE N E OE OEE 32 There are three different levels of hazard intensitv identified bv signal words DANGER WARNING and IMPORTANT The level of hazard is determined by the following definitions Observe the statements to ensure safety performance prevent injury and machine damage A A A Important Alerts against unsafe practices Observe to ensure drink quality machine performance food safety to prevent minor personal i
5. P aly WA OPERATION Rose JWIE EB a gt Machine equipped with manual water lever Place a jug or similar under the hot water outlet Open the hot water lever a Close the lever as soon as the machine has dispensed the desired amount of water 7 WARNINGI Never expose hands and fingers directly under the water outlet during operation to avoid scalding or serious burns a D Machine equipped with automatic water tap a Place a jug or similar under the hot water outlet AW w Press the hot water button for less than seconds for automatic dose dispensing Press for longer than second for continous dispensing Wait until the machine stops dispensing hot water automatically or press the button again to stop hot water dispensing A Important To obtain the best efficiency quality and performance of the machine you should always follow the cleaning and care instructions provided in this manual Turn off the power switch when cleaning the exterior of the machine All external surfaces should be cleaned with a wet cloth that will not get out fibers threads or scratch the machine Do not use aggressive cleaning detergents solvents or degreasers Th
6. Promotional display Number of coffees infusions dispensed Digital boiler temperature display and control PID technologv boiler temperature control m Programming and settings help system Visual water softener regeneration alarm Display language selector Tea if it is activated Continuous brewing ON STAND BY OFF Programming menu XXX C Ea The coffee machine has 3 possible statuses SELECT DOSES On The machine is operational and ready to make coffee This is the usual fig 04 ka machine status after turning on the power switch see fig 04 OFF hh mm Stand ba The power switch is on but the display shows Off see fig 05 This means that the machine is in energy saving mode This mode fig 05 is only entered whilst the machine is on To enter this mode press the Continuous Dispensing button and without releasing it simultaneously press the 2 Short Espressos button 69 To exit this mode and turn the machine back on press the 2 Short Espressos Button 69 again a Off The coffee machine is turned off at the power switch Doses setting Select within 30s fig 06 Set clock fig 07 a With the machine on press the Continuous Dispensing button on the Left hand drink buttons and hold it down for over 8 seconds until the dose programming menu is displayed All the drink buttons lights will be turned on and the Continuous Dispensing button light will flash The
7. boiler operating pressure Between 0 8 and 1 2 bar Between 0 8 and 1 2 bar Ambient noise lt 70 db lt 70 db MINI 2GR 2GR Front view of the machine Steam wand Drink Buttons Hot water lever Steam lever Capsule group lever Hot water outlet Oo e w 60 pied IEXPOJBAJR ON OFF switch Capsule Pump pressure drawer gauge Boiler pressure gauge Adjustable coffee Heater element lamp spout Front view of the machine Hot water lever Capsule group Steam lever lever Hot water outlet Displav Drink Buttons Steam wand c e 2 O i 2 ie IEX POBAJRI e Heater element lamp l ON OFF switch e Pump pressure gauge Adjustable coffee spout Turbo Steamer wand Capsule drawers IEXIPOBARI Rosetta mini 2Gr 530 mm 460 mm 590 mm 58 mm 115 mm 680 mm f to Rosetta 2Gr 530 mm 680 mm 590 mm 58 mm 115 mm 680 mm TRANSPORT Roses ERMEE The machine is shipped in a unique carton box which uses expanded polystyrene paddings The machine box is provided with conventional symbols that can be perfectly visible during the handling and storage tasks The machine b
8. by limescale Brewing groups do not dispense water Water system is clogged by limescale 90 of faults are due to limescaling inside the coffee machine due to not softening the water To avoid these faults maintain the water softener regularly f 32 For the warrantv to be valid the conditions for maintenance must have been followed according to our instructions proper precaution has been made and warranty claim been issued without delay The affected equipment may not be used during awaiting service if there is any risk that the damage or defect would worsen The warranty will not cover consumption supplies such as glassware normal maintenance such as cleaning of filters contaminations in water lime incorrect voltages pressure or adjustment of water amounts The warranty will not cover damages of defects caused by incorrect handling and operation of the appliance TECHNICAL SUPPORT Contact your supplier Your dealer Crem INTERNATIONAL www creminternational com Address of CREM international Shanghai Building 5 No 521 551 KangYi Road Pudong New Area Shanghai China Address of CREM international Spain C Comer n 4 Pol Ind Alcodar Gandia Valencia Spain MADE IN SPAIN
9. the values for the minutes in the same way and amp Note gt By default this setting is set as On indicating that the function is disabled Changing the value to anything other than enables the function To leave this function disabled press the 2 Short Espressos button whilst the value selected is hits ORO LI Vllax an ue time is flashing serene the NI ressing the short espresso an ong Espresso uttons Off hh mm B L L ee When the desired value is fig 10 Reached press the 2 Short Espressos button EB to accept it aered Or The minutes values will start flashing Set these values in the same way as Day described above and amp After accepting the time the next menu will be displayed fig I f auto on off is enabled it will also be possible to set a day on which the machine will not be turned on automatically This option will not be displayed if auto on off is disabled To set the day off see fig l Increase decrease the values by pressing the l short espresso and Long Espresso buttons When the desired value is reached press the 2 Short Espressos button 2S to accept it Note D By default this setting is set as On indicating that the function is disabled Changing the value to anything other than enables the function To leave this function disabled press the 2 Short Espressos button 89 whilst the value selected is
10. ROSETTA CAPSULE GROUP USER MANUAL Original instruction UM_EN Date 150106 CONTENT Rose JWIE EB GONMENT i gi a isabbat ap d a 2 SYMBOL DESCRIPTION Hazard intensity levels GENERAL Introduction General instructions Warnings a Precautions Intended use TECHINIGAE SPECIFIC ATO pa RT 7 Data sheet Accesories OVERVIEW OF COMPONENTS Rosetta mini control 2GR capsule Rosetta display control 2GR capsule DIMENSION SKETCH Rosetta mini control 2GR capsule Rosetta display control 2GR capsule sccisccssssscsssscesstssscsssssssssosvescsvsessssssdsstossesseasesnnesesuscesssssiasosssssvosecoseessssaastbascesteedsesie H TRANSPOR Tarenia sp REASERTAS ETEO 12 Packaging Delivery inspection IL A E E I E A E OT E I Positioning Electrical installation Connection tvpes Water connection Pressure and temperature Starting the machine OPERAT a A EA TR A IONS Espresso brewing Steaming and frothing milk with the manual steam wand Steaming and frothing milk with turbo steamer Dispensing hot water CLEANING AISI TPT ATI ED NAAT Go reani aie EE AR A efa 19 Coffee machine cleaning Daily cleaning Weekly Gleaming sssssscsssssssssscscavsssarasasssscssessssvassavacscssvsssvsssssseississssvesessiasataasatsaisnosasstbsassassatansssanasiosassbsssecssasiessisassshcsuaasissieass 2 CONTENT Roses JWIE EB
11. a horizontal position in a water resistant location Install the machine away from heat sources and flammable objects This appliance is not suitable for installation in an area where a pressure washer may be used Do not use the machine outdoors where it would be exposed to adverse weather rain snow frost This will cause material damage to the machine If the mains cable is damaged it must be replaced by the manufacturer its service agent or a similarly qualified person in order to avoid a hazard Do not remove or disable any of the mechanical electrical or thermal protection mechanisms sl GENERAL a In case of emergency e g the machine catches fire or becomes unusually hot or noisy disconnect the power immediately and close the water inlet tap a If the machine is not going to be used for a prolonged period of time disconnect the power When disconnecting the power pull the plug rather than the cable a When packed for storage keep the machine in a drv place with an ambient temperature of over 5 C Boxes mav be stacked in piles of up to three units of the same model Do not place other heavier packages on top of the box The machine is likelv to be exposed to temperatures below 0 C during handling and transport make sure that service personnel empty the boiler and water system The machine s boiler and water system is empty when delivered from the factory To ensure fault free machine operation onl
12. allation The coffee machine should only be connected to the power supply by qualified personnel The following safety instructions should be followed at all times a Check that the electrical specifications on the ratings plate match the specifications of the power supply at the point of installation The coffee machine must be connected to an earthed socket that complies with the regulations in force in the country of installation You should protect the electric line of the installation with a circuit breaker switch appropriated for the power consumption of the machine specified on its ratings plate A residual current circuit breaker must be installed in accordance with the characteristics of the area of the installation Check the characteristics power rating of the system and that the diameter of the cables are suitable for the power used by the machine Do not connect the coffee machine to the power supply via extension boards adapters or shared sockets The manufacturer will not be held liable for damage to persons animals or property resulting from incorrect installation of the coffee machine A DANGER If the mains cable or plug is damaged it must be replaced by the manufacturer its service agent or similarly qualified persons in order to avoid SERIOUS INJURY OR DEATH Connect the machine as per the instructions on the ratings plate Machine 220 240Vac Ph N Supply Machine 220 240Vac Ph N Supply Mac
13. cup in the machine connect the other to the main drainage tube at the installation area A Important Only use the hoses supplied with the machine Never reuse hoses Make sure that the drainage tube is not twisted and ensure that the entire tube is below the level of the drain cup Boiler temperature and pressure are directly related see Fig 01 Machine is fitted with a pressure gauge that will display the boiler pressure if the machine is fitted with a display it will also indicate boiler temperature C Relationship between boiler pressure and temperature 125 120 115 110 BAR 0 7 0 8 0 9 l l 1 2 L I Standard pressure and temperature Fig OI m Open the external supplv of water to the machine Turn on the main power switch Press a drink button at the control panel on each group wait until water comes out continuously from each of them This way the heat exchangers in the machine will be correctly filled m Open the steam tap to release the air trapped in the boiler The red lamp indicates that the boiler is heating The lamp switches off when the machine reaches operating temperature The machine is now ready to use OPERATION Rose JWIE EB Lift up the lever for the group the last used m Insert the capsule in the correct position as capsule will be ejected into the capsule drawer shown in the picture and push down the lever into l
14. display will be as shown in fig 06 Hold down the Continuous Dispensing button until the menu displays the set clock option see fig 07 This provides access to the second menu level Clock adjust hh mm Day fig 08 To set the clock press the 2 Short Espressos button 2S whilst the Set clock message is displayed The hours values will start flashing Increase decrease the values by pressing the Short Espresso and Long Espresso buttons see fig 08 With the desired value is reached accept it the pressing the 2 Short Espressos button 2S The minutes digits will now start flashing Increase decrease the values by pressing the Short Espresso and Long Espresso buttons With the desired value is reached accept it the pressing the 2 Short Espressos button 2S Set the day of the week in the same way l and 69 After setting the values pressing the 2 Short Espressos button 69 accesses the auto On Off menu Pawo Auto On Off After accepting the changes made in the set clock menu pressing the 2 Short Espressos button fee accesses the coffee machine s auto on off On hh mm programming menu see fig 09 To change the auto on off time increase decrease the values hours using the short espresso and Long Espresso buttons whilst the values are flashing When the desired value is reached press the 2 Short Espressos button 2S to accept it Set
15. ey can damage the machine Important Once a day or after 8 hours from the last dispensing of coffee the following cleaning tasks must be performed for maintaining the quality and performance of the water system in the machine Capsule group Brew a continuous coffee without capsule for around one minute Steam wand Position the wand outside the drip tray and open the steam lever for around one minute Manual hot water outlet Place a container under the water outlet and open the tap for 20 seconds Automatic hot water outlet Place a container under the water outlet and press the hot water button for 3 seconds to start dispense water for 20 seconds a Rinse the capsule group with hot water Clean the external surfaces of the machine pay special attention to the stainless steel parts m Clean the steam wand and the water lever Be sure that the nozzles are not blocked or half blocked with for example milk residue If it s necessary to clean be careful not to deform or damage any of the components Clean the dip tray and the stainless steel insert grid under running water with a brush You can slowly pour IL of hot water into the drain cup to dissolve and remove coffee residue that have accumulated inside the cup and tubes Clean the capsule group with professional cleaning powder or cleaning capsule page 21 Clean the group gasket see page 22 a Clean the coffee spout page 23 Ope
16. frothing milk Do not use it for any other purpose a The machine is intended to be used by trained personnel for preparing foodstuffs This machine is not intended for use in industrial kitchens domestic kitchens or similar locations The manufacturer will not be held liable for damage to persons or property due to incorrect improper or negligent use by non professional personnel To ensure optimal performance install the machine in a location where these parameters will not be exceeded Maximum permissible inlet water pressure 600 KPa 6 Bar minimum permissible inlet water pressure 200 KPa 2 Bar Maximum inlet water temperature 40 C Ambient temperature is between 10 C min and 40 C max TECHNICAL SPECIFICATIONS Data sheet Machine model Standard EBAD C32D 12AF 220 230V IN 2600W 50 60Hz Machine model Take Away Steam wand l unit 2 units Hot water lever l unit l unit Turbo steamer No Optional Temperature control Regulated by pressure switch Regulated by PID Programmed via display No Yes Height adjustable brewing system Yes Yes Energy saving mode No Yes Height width depth mm 680 460 590 680 680 590 Boiler volume I 6 MES Power supply 220 230V IN 2600W 50 60Hz 230V IN 3740W 50 60 Hz Connecting to the water supplv Female 3 8 thread Female 3 8 thread Weight kg 39 75 53 50 Steam
17. hine 125Vac Ph N Supply 220 240Vac Ph N 2Ph 220 240Vac 125Vac PhEN O NEUTRAL Blue OI NEUTRAL Supply hose Supply hose Yellow Green Machine 2Ph N Supply Machine 2Ph N Supply Machine 380Vac 3Ph Supply 220 240Vac Ph N 2Ph 380VactN 3Ph 380VactN Blue 6 NEUTRAL Brown Supply hose Machine 2Ph N Suppl Machine 2Ph N l Machine 220 240Vac 3Ph Suppl pp y pp y pp y 2Ph 220 240Vac 0 rh 220 240 3Ph 220 240Vac Supplv hose INSTALLATION M The Installation of the machine to a water mains connection must be done by a qualified person Rinse around 20 liters of water from the main water supply before connecting the machine to the water connection Connect the inlet hose that is assembled in the machine to the main water supply which should have a 3 8 male connection fitted with a shut off valve tighten it with a wrench Use safe drinking water with hardness between 5 fH and 8 fH French hardness degrees If the value is below this limit the presence of corrosion of hydraulic components is a possibility If the value is higher than this limit the presence of lime in the boiler will increase In both cases the operation of the machine and coffee quality will be affected negatively If necessary connect the machine to a water softener or remineraliser to reduce water hardness Use the flexible hose that is included in the accessory box of the machine Connect one end of the corrugated tube to the drain
18. his process 5 times Turn the machine off at the Push the metal tension ring After the tension ring releases main power supply switch pictured in blue back using pull the gasket forward from and then open up the capsule thumbnails or a plastic tool one edge until it releases from group until it slides off of the gasket the capsule holder Note To remove the group gasket the AN WARNING Be aware of the sharps machine must cool to room temperature inside the capsule holder to avoid injury Clean the capsule holder with warm water and a brush m Clean the gasket with water and a brush then rinse with clean water before reinstalling A Important The wider face of the gasket must be facing out when reassembling the gasket onto the capsule holder Hold the capsule group lever with one hand to keep the capsule holder stable With the other hand place the gasket on the capsule holder with the lip seated at the bottom first Then press the gasket onto the holder working around until it is completely seated 2 Pull the metal tension ring up onto the gasket to hold it in place Ensure the ring is aligned evenly f 22 r p pe 3 A A dD N XI GU X KI a Pull down the spout to its lowest position Once in its lowest position squeeze the hooks on each side that hold the spout in place and pull downward
19. hot water Press the button again to stop dispensing hot water The new dose setting will be saved Each button panel can be programmed with different doses note that the left hand button panel will always override the others f 26 PROGRAMMING oe JNMGGANAAAA Programming the turbo steamer To program the temperature at which the turbo steamer will stop automaticallv Press the Continuous Dispensing button and hold it down for 8 seconds The continuous dispensing button light will flash and all of the button panel lights will be turned on see fig 02 Insert the steam wand with built in temperature gauge in the jug containing the milk and press the Continuous Dispensing button on the left hand button panel The automatic steam wand will start dispensing steam and will heat the milk in the jug see fig 03 When the milk reaches the desired temperature press again to stop dispensing The new heating temperature will be saved Fig 02 Fig 03 D Note Use a thermometer to measure milk temperature when programming the turbo steamer To adjust the amount of air injected into the steam and therefore the creaminess of the steamed milk contact service personnel Preciosa Machines equipped with a display include the following additional functions Automatic daily on off timer stand by function Clock settings current time and date a
20. mains and empty the boiler this should be performed by a qualified person Clean the drip tray and exterior of the machine m Pack and send the machine to a certified recycling center Sq B24 PROGRAMMING Here is some of the additional functions that the electronics offers Volume control of four different espresso drinks per brewing group Time controlled hot water dispensing if available Automatic filling and level control of the boiler Automatic switch off of the heating element if not enough water System supervision through alarms RS 232 serial interface with reader for connecting control panel and computer Automatic cleaning of the brew groups The control panel is by default programmed with 4 standard drinks these can be reprogrammed as you wish and a continuous selection The first four keys l short espresso Long Espresso 2 short espresso 2 Long Espresso brew the programmed volume and then stop automatically the fifth key brews continuously until user i it by pressing button again SR S Hot water Automatic steam if enabled 2 Short Espressos Continuous Dispensing Auto cleaning I Short Espresso Long Espresso 2 Long Espressos KA l 0 The Continuous Dispensing button performs 3 different functions depending on length of time pressed Machines equipped with displav Under second Enables automatic water or steam dosing only on machines without manual taps
21. n the lever so the last used capsule Push down the lever into locked position falls into the capsule drawer and the group Start the continuous brewing and stop after becomes empty 30 seconds Repeat this process 3 times Reopen the lever and put an empty capsule Push down the lever into locked position without any cleaning agent in the group Start the continuous brew for 30 seconds Repeat this process 3 times Note You can take a used coffee capsule and open it up and remove the coffee powder inside to use in step 3 Cleaning with powder m Open the lever so the last used capsule Push down the lever into locked position falls into the capsule drawer and the group Start the continuous brewing and stop becomes empty Fill half of the capsule after 20 seconds Repeat this process 5 group with special cleaning powder for times espresso machines Cleaning with capsule amp Note Only use professional cleaning powder for espresso machines It s avalible from your distributor A Important We recommend to clean and rinse the machine at least once a week A Important Always rinse the group after a cleaning procedure Part no 1104162 Open the lever so the last used capsule falls into the capsule drawer and the group becomes empty Insert the special cleaning capsule start the continuous brewing and stop after 20 seconds Repeat t
22. njury or damage to the machine WARNING Indicates a potentially hazardous situation which if not avoided could result in scalding serious injury and even death DANGER INDICATES A IMMINENTLY HAZARDOUS SITUATION WHICH IF NOT AVOIDED WILL RESULT IN SERIOUS INJURY AND EVEN DEATH Note Gives additional information which may be helpful during the cleaning procedure or operation of the machine GENERAL Thank vou for choosing a Rosetta capsule machine We hope you enjoy it 1 Read the user manual before using the machine This manual contains important instructions on intended and safe use of the coffee machine Keep this manual close to hand for future reference If damaged or lost request a copy from the manufacturer a Machine installation and certain maintenance operations should only be performed by qualified service personnel All safety instructions and warnings contained in this manual should be observed to ensure safe installation use and maintenance Do not attempt to open or repair the machine or access the interior Repair should be performed by an authorised workshop by a service centre or by qualified service staff Do not remove operational or protective parts requiring use of tools for removal Purchasers are liable for ensuring that users have been trained to operate the machine and have been informed of the potential risks involved The installer will be held liable for all n
23. ns lights will be turned on Press the dispensing option that you wish to program Short Espresso Long Espresso 2 Short Espressos or 2 Long Espressos The lights on the button pressed and on the Continuous Dispensing button will remain on The group will start dispensing coffee When the desired volume is reached in the cup press the selected button again to stop dispensing This volume setting will be saved On machines equipped with a display the lights on the reprogrammed dosage buttons will remain off Repeat this process for all of the dispensing options that you wish to reprogram If you only need to reprogram one of the dispensing options follow the steps above and program just that option All of the other dispensing options will remain unchanged default settings Note D Programming any of the options on the left hand Drink buttons when viewing the machine from the front automatically sets the dispensing volumes on all of the other Drink buttonss This only applies to the left hand Drink buttons Programming other Drink buttonss only modifies the option selected This function is only available in models equipped with an automatic water lever Press the Continuous Dispensing button GS and hold it down for 8 seconds The Continuous Dispensing button light will flash and all of the lights on the button panel will be turned on Briefly press the Continuous Dispensing button The water lever will start dispensing
24. ocked position Adjust the height of the coffee spout if necessary Place a cup under the coffee outlet A Select the desired drink by pressing any of the buttons B A WARNING Never open the capsule group whilst the machine is dispensing a drink as the pressurized hot water could cause scalding or serious injury Once dispensing has finished wait about 3 seconds before opening the capsule group 5i OPERATION Rose JWIE EB EXPOBAR Immerse the steam wand into the jug containing the m Place the steam wand over the drip tray and milk make sure the wand tip is submerged open the steam tap for a few seconds this will allow condensed water to be ejected Close the steam tap when only steam comes out m Once the milk reaches the desired temperature close the tap and remove the jug Open the tap again to start heating or frothing the milk A WARNING Do not remove the steam wand from the jug whilst the steam lever is open Doing so may result in scalding and serious injury After the process is finished position the steam wand over the drip tray and open the steam tap for a few seconds to clean leftovers of milk in the wand Close the tap and clean the outside of the steam wand with a damp cloth to prevent nozzle blockage OPERATION
25. on authorised modification of the machine Non authorised alteration or modification of the machine will exempt the manufacturer of all liability for damages and will invalidate the warranty This manual refers to the machine as at the time of sale The commercial availability of subsequent versions featuring modifications upgrades or adaptations does not oblige the manufacturer to apply the same to this machine nor does it oblige it to update the documentation supplied The manufacturer reserves the right to withdraw currently available manuals whenever it considers appropriate and reasonable The manufacturer will not be held liable for damage to persons or property attributable to failure to follow the instructions and warnings listed below when installing and using the coffee machine Place the machine in a location accessible only to personnel trained to operate it Keep all hazardous packaging materials such as plastic bags expanded polystyrene and staples out of reach of children Plug the machine into a properly installed earthed safety socket whose line voltage matches the technical data for the machine Make sure that the power supply voltage does not fluctuate by more than 6 Position the power cable so that users cannot trip over it Keep the power cable away from sharp edges and heat sources m Children should be supervised to ensure they do not play with the appliance Install this appliance in
26. ox must stay in a vertical position during the transport Do not tip or try to place the box tilted sideways in any way During transportation the box must be protected from hits impacts shocks and exposure of bad weather elements After the delivery check that the machine is in the exact condition described in the documentation of the transport accessories included Check that the machine does not have any damage caused by transportation If this happens inform to the shipper and the distributor of the machine The packaging materials are potentially dangerous and should be kept away from children Make sure to leave the materials of the box and packaging at a suitable recycling center INSTALLATION MIN 10cm a Install the machine on a level surface Adjust the feet to lt lt MIN 30cm ensure that it dispenses coffee evenly in all of the cups Select a level dry strong and stable installation surface at least 110 cm off the floor Leave enough space above and behind the machine to ensure easy cleaning and maintenance Do not install the machine whilst wet or damp If wet or damp leave the machine until completely dry then ask service personnel to check that none of the electrical components are affected Note D Leave an air gap of approximately 30 cm above ri s the machine and 10 cm behind it to ensure ventilation INSTALLATION Rosea Capsule Group Electrical inst
27. s oe OX B m Remove the funnel inside the spout by pulling m Clean the two parts with a brush under it straight up running water reassembly the parts in reverse order Important Avoid placing wet cups directly on the cup shelf it may drip into the machine and cause machine damage Remove and insert the porta filter gently fer NS O Never use excessive force to try to close the i porta filter m When raising and lowering the lever to insert a capsule do so slowly Never force the lever STORAGE AND DISPOSAL OF MACHINE m Make all the cleaning procedures described in this manual Disconnect and roll up the power cord this should be performed by a qualified person Disconnect the inlet hose from the machine to the water mains and empty the boiler this should be performed by a qualified person Clean the drip tray and exterior of the machine m Cover pack the machine and store it in a dry place where it isn t exposed to bad weather conditions m f the machine should be used after a long period of storage make sure to run all cleaning procedures before using the machine again Make all the cleaning procedures described in this manual Disconnect and roll up the power cord this should be performed by a qualified person Disconnect the inlet hose from the machine to the water
28. se from the flow meter coffee too fine or flow meter fault within 5 seconds of pressing one of the espresso buttons the light for the dose selected will start to flash To disable it press the dose button again Asan additional safety all dose settings have a maximum dispensing time of 5 minutes TROUBLESHOOTING The following checks can be carried out bv users once the machine has been turned off and disconnected from the power supply For all other non specified machine faults disconnect the machine from the power supplv and immediatelv contact authorised and qualified service personnel The machine does not start up The plug is not correctly inserted into the power socket Check that the plug is correctly inserted and that the power socket is operational The circuit breaker and or differential are disconnected Check that they are connected The cable and or plug are damaged Call service personnel to replace them Below standard coffee froth quality The coffee spout is clogged or dirty Clean the coffee outlet nozzle The steam wand does not dispense steam The steam wand is clogged by milk Clean the wand and if necessary remove the nozzle and unclog it using a pin or needle Water is found underneath the machine The drainage tube is blocked Clean the drainage tube Coffee not dispensed at right temperature Heat exchanger outlet pipes clogged
29. y use replacement parts and accessories authorised by the manufacturer a Before performing maintenance and or moving the machine disconnect the machine from the power supply and wait for it to cool Do not place vessels containing liquid on the machine a This appliance must not be cleaned with a pressure washer a Never immerse the machine plug or mains cable in water as there is a danger of electric shock Do not touch the machine s hot surfaces or dispensing equipment Do not touch the machine if your hands or feet are wet Do not operate the machine if any part except the dispensing equipment is wet a Place the machine out of reach of children This appliance can be used by children aged from 8 years and above and persons with reduced physical sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved Cleaning and user maintenance shall not be made by children Do not use the machine if the machine its mains cable or the plug is damaged or the machine has been dropped Do not obstruct the vents with cloths or other objects Do not insert foreign objects into the vents Check the drain regularly to make sure that water is emptied properly This coffee machine has been designed and manufactured to make espresso coffee and other hot drinks e g steaming and
Download Pdf Manuals
Related Search