Home

MASTER CONTROL MV-58 Owner`s Manual

image

Contents

1. Classic Effect Synchronizer e SIXY Line 6 Tempo Controller e CV SYNC Control Voltage Synchronizer e MIDI SPLITTY Pedalboard MIDI Splitter Repeater e NODE 4 Loop MIDI PedalBoard Switcher e SIMI Modular MIDI Display Many more available soon MIDI IMPLEMENTATION CHART Function Generated Comment Note On Note Off Aftertouch Control Change Program Change Channel Pressure Pitch Bend System Common System Exclusive On selected MIDI Channel OXXX O X lt gt lt gt lt gt lt Molten Voltage self program instruction sent during program save SIMI SysEx data sent during Passive Mode v 1 08 System Realtime O Only MIDI Start Stop and Clock Note that versions 1 06 and older manufactured before 10 15 14 also send Song Select data at the same time and same value as the Program Change value O YES X NO questions MoltenVoltage com 2015 MoltenVoltage com All Rights Reserved v 1 09 Molten Voltage Master Control MV 58 Owner s Manual p 10 TROUBLESHOOTING Problem Solution Master Control will not turn on Plug in 9 volt DC 2 1mm Tip Negative Power Supply Clicking or Noise Use a separate or isolated Power Supply for Master Control MIDI device is not receiving MIDI Make sure your other MIDI device is configured to receive MIDI Clock Consult the User s Clock Guide for that device MIDI device
2. Lock in your selection by pressing the Down button Switch between the two modes during runtime by pressing both the Up and Down buttons at the same time Version 1 08 always allows switching modes during runtime Version 1 09 allows you to turn this feature on and off by holding down the Down button while powering on Master Control The MIDI Channel number will be displayed first Press the Start button until the display reads rt Y real time Yes or rt n real time No Switch modes by pressing the Up button Lock in your selection by pressing the Down button v 1 09 default is to have this feature off SIMI SysEx Compatibility version 1 08 and later When selecting pending programs in Passive Mode Master Control version 1 08 and later will send out SysEx data allowing SIMI to flash the pending program name The default is for this feature to be active To turn this feature off hold down the Down button while powering on Master Control The MIDI Channel number will be displayed first Press the Start button until the display reads Sd Y send Yes or Sd n send No Switch modes by pressing the Up button Lock in your selection by pressing the Down button Factory Preset Values Programs 1 64 are 120 bpm Programs 65 128 are oLd MIDI Channel 15 questions MoltenVoltage com 2015 MoltenVoltage com All Rights Reserved v 1 09 Molten Voltage Master Control MV 58 Owner s Manual p 9 Related Products e CTL SYNC
3. is not receiving MIDI Set your MIDI device to receive MIDI Program Change messages on Channel 15 Program Change messages MIDI Clock stops Check Power Supply connection Replace MIDI cable with one under 15 feet General Guidelines Keep MIDI cables as short as possible Long cables can cause errors If you need more length consider using a MIDI repeater 7 If you are daisy chaining MIDI devices the total MIDI cable length must be considered if any MIDI devices do not amplify the data signal questions MoltenVoltage com 2015 MoltenVoltage com All Rights Reserved v1 09 Molten Voltage Master Control MV 58 Owner s Manual p 11 Support questions MoltenVoltage com Warranty Molten Voltage is proud of its products and warrants this unit for a period of two 2 years from the date of purchase to be free from defects in materials and workmanship under normal use and service as long as the unit is used with an approved power supply and consistent with these instructions Contact Service MoltenVoltage com regarding repairs Any user repair attempts void the warranty PROOF OF PURCHASE IS REQUIRED FOR WARRANTY REPAIRS DISCLAIMER Information contained in this publication regarding device applications and the like is provided only for your convenience and may be superseded by updates It is your responsibility to ensure that your application meets with your specifications MOLTEN VOLTAGE
4. press the UP Button to cycle through the 16 possible MIDI channels the cycle will start over at zero after Channel 16 is reached 4 Once the desired MIDI Channel is reached press and release the DOWN Button again The unit will re start with the new MIDI Channel stored in memory questions MoltenVoltage com 2015 MoltenVoltage com All Rights Reserved v1 09 Molten Voltage Master Control MV 58 Owner s Manual p 8 Active and Passive Program Select Modes version 1 08 and later MV 58 version 1 08 and higher has two modes for selecting programs Active and Passive In Passive Mode pressing the Up or Down buttons selects a pending program indicated by the flashing program number The program is not sent until the Start button is pressed Passive Mode is the default and the way that all earlier versions operate In Active Mode each time the Up or Down button is pressed the corresponding MIDI Program Change is sent instantly This is true whether MIDI Clock is being sent or not The current mode is indicated by the decimal point in the displayed program number The decimal point flashes while in Passive Mode and stays lit all the time in Active Mode You can select which mode will be used on startup by holding down the Down button while powering on Master Control The MIDI Channel number will be displayed first Press the Start button twice until the display reads Pnd or Act Switch modes by pressing the Up button
5. AP Button G TEMPO LED H SELECT Knob I DC Power Jack J MIDI OUT Jack Designed with the end user in mind The Master Control interface has been designed to make switching and storing programs as simple as possible so the end user can concentrate on being creative Programs are selected using the UP and DOWN buttons or by turning the SELECT Knob The selected program number is displayed on a large bright 3 segment LED display The selected program is engaged by pressing the START Button Making Master Control and all connected Molten Voltage devices save their current settings is even easier simply hold down the TAP Button for 2 seconds START Button B The START Button is used to start and stop the MIDI Clock data output and to change Programs Each time the clock is started or stopped a corresponding MIDI Start or MIDI Stop command is sent The Tempo will be reset and synchronized each time the clock is started Note MIDI Start Stop and Clock are not channel specific questions MoltenVoltage com 2015 MoltenVoltage com All Rights Reserved v1 09 Molten Voltage Master Control MV 58 Owner s Manual p 3 If a Program is running i e currently sending Clock data pressing the START Button will stop the clock unless a new Program number has been selected In that case pressing the START Button will send the new Program Change message and the Clock data will continue uninterrupted When a new Progr
6. CONTROL OWNER S MANUAL sire Vounce Congratulations on purchasing the Molten Voltage Master Control MV 58 Master Control MV 58 is a programmable MIDI pedalboard controller that stores the tempo associated with 128 programs and transmits MIDI Clock to synchronize your MIDI enabled effects Key Features Fully functional stand alone Master Controller for MIDI controlled PedalBoards Rock Solid MIDI Clock Generator Call up presets on your MIDI enabled effects Solid Professional Grade construction including Riveted Steel MIDI Jack Large vivid LED display very easy to read Programmable pedalboard tempo control to synchronize your effects Versatile tempo control including precision tap tempo MIDI Program Change and MIDI Start Stop and Clock output Robust 128 program storage Causes other compatible Molten Voltage devices to self program Simple intuitive user interface questions MoltenVoltage com 2015 MoltenVoltage com All Rights Reserved v 1 09 Molten Voltage Master Control MV 58 Owner s Manual p 2 CONNECTING Plug in a separate or isolated 9 volt 2 1mm 100mA minimum tip negative DC Power supply into the DC9V jack I Avoid powering Master Control using a daisy chained power supply that is also connected to audio effects MV 58 self contained MIDI controller A CLOCK LED B START Button C Display D DOWN Button E UP Button F T
7. MAKES NO REPRESENTATIONS OR WARRANTIES OF ANY KIND WHETHER EXPRESS OR IMPLIED WRITTEN OR ORAL STATUTORY OR OTHERWISE RELATED TO THE INFORMATION INCLUDING BUT NOT LIMITED TO ITS CONDITION QUALITY PERFORMANCE MERCHANTABILITY OR FITNESS FOR PURPOSE Molten Voltage disclaims all liability arising from this information and its use No licenses are conveyed implicitly or otherwise under any Molten Voltage intellectual property rights MASTER CONTROL NODE SIMI MIDI SPLITTY TEMPODE CTL SYNC CV SYNC Molten Voltage and Visionary Effects are all trademarks of Molten Voltage Legal MoltenVoltage com questions MoltenVoltage com 2015 MoltenVoltage com All Rights Reserved v1 09
8. Program Change data is sent Note If you tap in a new tempo you need to wait until you are done tapping and Tap Mode ends about 2 5 seconds after the last tap before you can store the new tempo Note MIDI Clock output will stop while Molten Voltage self program data is sent As such it will usually be necessary to restart drum machines sequencers etc after storing a tempo questions MoltenVoltage com 2015 MoltenVoltage com All Rights Reserved v1 09 Molten Voltage Master Control MV 58 Owner s Manual p 5 DOWN Button D Pressing and releasing the DOWN Button will decrease the Program number by one Pressing and holding the DOWN Button will quickly decrease the Program numbers If the TAP Button has been pressed and released pressing the DOWN Button will decrease the tempo by one bpm Pressing and holding the DOWN Button will quickly decrease the tempo Once the DOWN Button has been pressed subsequent Taps will not affect the tempo until the 2 5 second tempo change time out occurs however the UP Button and SELECT Knob can still be used to change the tempo UP Button E Pressing and releasing the UP Button will increase the Program number by one Pressing and holding the UP Button will quickly increase the Program numbers If the TAP Button has been pressed and released pressing the UP Button will increase the tempo by one bpm Pressing and holding the UP Button will quickly increase the tempo Once th
9. adjusted tempo and light up the far right decimal point to indicate a new tempo has been received Once at least one tap is received the UP and DOWN Buttons and the SELECT Knob can be used to fine tune the tempo Note After the UP or DOWN Buttons are pressed or the SELECT Knob is turned additional taps have no effect Maximum tap interval 2 5 seconds 24 bpm Minimum tap interval 0 25 seconds 240 bpm questions MoltenVoltage com 2015 MoltenVoltage com All Rights Reserved v1 09 Molten Voltage Master Control MV 58 Owner s Manual p 4 Tempo change times out after 2 5 seconds If a single tap was received then the display again shows the currently selected Program number If multiple taps were received then tPo SEt Tempo Set will be displayed to indicate that a new tempo has been received The Display will then show the currently selected Program number Note This new tempo is only temporary and will not be saved unless the Program is saved Tempo can be continually adjusted on the fly with the TAP TEMPO Button whether or not MIDI Clock is being sent Tempo changes affect only the current Program and are not stored unless the SAVE function is used Similarly Tempo changes do not affect any pending Program indicated by a flashing Program number However if the pending Program uses the oLd tempo it will use the existing tempo Program Storage Master Control stores the tempo associat
10. am number has been selected but not yet engaged the Display will flash If no Program is running pressing the START Button will cause a MIDI Start command to be sent together with Program Change data followed by a constant stream of Clock data Note Stopping then re starting the same Program does not cause additional Program Change data to be sent Note If the tempo has been altered but not saved stopping then re starting the same Program does not recall the stored tempo instead the altered tempo will continue to be used rather than the stored tempo If a different Program is used and later the previous Program is recalled the previous Program will recall its stored tempo rather than the altered tempo In order to keep an altered tempo the Program must be saved as described below Note No program change is sent when powering up To send the first program change the start button must be pressed TAP Button F The TAP Button performs two separate functions Tempo Control and Program Storage Tempo Control When the TAP Button is first pressed the current tempo is displayed This provides a simple way to check the tempo without altering it Pressing the TAP Button again within 2 5 seconds will adjust the tempo to the interval between the taps The new tempo starts right after the second or most recent tap The time between the two most recent taps a ways corresponds to the length of a quarter note The Display will show the
11. e UP Button has been pressed subsequent Taps will not affect the tempo until the 2 5 second tempo change time out occurs however the DOWN Button and SELECT Knob can still be used to change the tempo MIDI OUT Jack J Connect Master Control to your MIDI device that will receive MIDI data by plugging a standard 5 pin DIN MIDI cable into the MIDI OUT jack For best results keep the MIDI output cable length under fifteen 15 feet If you need more distance use a MIDI repeater such as MIDI SPLITTY The MIDI OUT Jack sends MIDI data as well as Molten Voltage self programming messages SELECT Knob H Turning the SELECT Knob will cause the program number to increase or decrease When a new program number has been selected the Display will flash until the START Button has been pressed and the selected program is engaged questions MoltenVoltage com 2015 MoltenVoltage com All Rights Reserved v 1 09 Molten Voltage Master Control MV 58 Owner s Manual p 6 If the TAP Button has been pressed and released turning the SELECT Knob will increase or decrease the tempo up to the 24 240 bpm limits Pressing and holding the UP or DOWN Button will quickly increase or decrease the tempo Once the SELECT Knob has been turned after a Tap subsequent Taps will not affect the tempo however the UP and DOWN Buttons can still be used to change the tempo CLOCK LED A When the CLOCK LED is illuminated MIDI Clock data is bein
12. ed with each of the 128 programs Holding down the first press of the TAP Button for more than 2 5 seconds causes Master Control to save the current tempo at the selected Program location Once the TAP Button has been held long enough the Display shows the letter P Release the button to store the program At the time the tempo is stored Master Control simultaneously sends a command to all compatible Molten Voltage devices connected to the MIDI OUT causing them to self program and store their settings for the selected Program The selected Program is the one that is shown by the Display If the Program number is flashing the selected Program is not the same as the one that is currently running As such the current Program can be copied into a new Program location by selecting a different program number but not engaging that Program normally done by pressing the START Button Instead hold down the TAP Button until the letter P appears The current settings will be saved to the selected Program when the button is released If the DOWN Button is pressed while the TAP Button is being held and after the letter P appears the decimal point after the P will turn on This indicates that Master Control will not save the current tempo but instead will set the tempo status to oLd meaning that Program will use the then current tempo when it is recalled Following a SAVE the saved Program becomes the current Program and
13. evious Program then the far right decimal point will be on When the TAP Button is pressed for less than 2 5 seconds the current tempo will be displayed The tempo can then be changed by tapping again pressing the UP or DOWN Buttons or turning the SELECT Knob Programming information If the TAP Button is pressed and held for 2 5 seconds the display will show the letter P to indicate that upon release of the button the selected Program will be stored If the DOWN Button is pressed while the TAP Button is being held the decimal after the P will turn on indicating that program will use the oLd tempo from the previous Program rather than the current tempo MIDI Compatibility The primary MIDI channel for the Molten Voltage system is MIDI Channel 15 All MIDI Program Change messages are sent exclusively on that channel Molten Voltage devices all read MIDI messages on Channel 15 by default Set any other devices to receive MIDI Program Change messages on Channel 15 Changing MIDI Channel Although changing the MIDI Output Channel is not recommended because Molten Voltage devices read MIDI messages primarily on Channel 15 it is possible to change the Master Control MIDI Output Channel as follows NAM 1 Hold down the DOWN Button as you power the unit on The unit will display a lowercase c with a period after it follow by the current MIDI Channel e g c 15 2 Release the DOWN Button 3 Repeatedly
14. g sent over the MIDI OUT Jack The CLOCK LED is toggled when the START Button is pressed unless a Program is running and a new Program number has been selected as described above TEMPO LED G The TEMPO LED always flashes in time with the current tempo at quarter note intervals The tempo corresponds to the standard quarter note interval of 24 MIDI Clocks Note MIDI Clock data is not being sent unless the CLOCK LED is illuminated Display C The Display provides a variety of information On startup the Display shows the version information flashes Program 1 and shows its tempo then indicates Program 1 Program number The Display shows Program numbers as follows Programs 1 99 appear as P 1 through P 99 un m Programs 100 128 appear as u 00 through u 28 u means upper Program 27 Program 128 Programs are selected with the UP and DOWN Buttons and the SELECT Knob as described above If the Display is flashing a program number a new Program has been selected but not engaged Once the new Program is engaged by pressing the START Button the Display will stop flashing questions MoltenVoltage com 2015 MoltenVoltage com All Rights Reserved v 1 09 Molten Voltage Master Control MV 58 Owner s Manual p 7 Tempo information If a Program has a fixed tempo associated with it the far right decimal point after the last character will be off If a Program uses the oLd tempo from the pr

Download Pdf Manuals

image

Related Search

Related Contents

TRIP TRACKER APPLICATION ON ANDROID  V81291A Istr.Uso Whad 1000  C510 - T2voice  H:\Ale\Professione\2012\Parco\Progetto GPP\riuso_progetti_da alba  RADEX -N Composite    User Manual  AC-172N-1790 MANUAL DE INSTALACIÓN Y PREPARACIÓN  Rapoo 1070P  Operator Panel OP37/Pro  

Copyright © All rights reserved.
Failed to retrieve file