Primex Wireless, Inc
Contents
1. 1310 Kerrisdale Blvd Unit 4 Newmarket ON L3Y 8V6 800 330 1459 www primexwireless ca 2 2 Sequence of Operation Transmitter Operation When power is first applied to the transmitter it checks for and displays the software version It then checks the position of the switches and stores their position in memory The transmitter looks for the master time source Specifier Note Select procedure appropriate to the master time source from either of the following GPS Time Source With the XR transmitter in GPS mode it powers a connected GPS engine mounted with a clear view of the sky Upon power the GPS module seeks the GPS satellites in orbit to determine position and UTC time Once the transmitter acknowledges receivable GPS data it downloads time data and synchronizes its internal master clock 16730 6 OAANINDNBWN KR XR Wireless Clock Systems Division 16730 to GPS time The transmitter then starts to transmit its internal time once every second The transmitter updates its internal clock every time it receives valid time data from the GPS NTP Time Source With the XR transmitter in NTP mode it connects over the Ethernet to the IP address of the NTP server This IP address is programmed into the transmitter as part of its configuration Once the connection to the NTP server is acknowledged it downloads time data and synchronizes its internal master clock to NTP time The transmitter then starts to transmit its internal t2. and 12 5 inch 317 5mm analog clocks shall have a tamper proof theft resistant clock lock mounting slots Specifier Note Select optional dial designs colors case options and hands from manufacturer s brochure Analog clock receivers shall be as follows Receiver sensitivity gt 110 dBm Receiver power dual lithium battery pack supplied by manufacturer Antenna type internal Antenna gain 7 dBd 16730 11 OANINNHBWNH XR Wireless Clock Systems Division 16730 If the transmitter stops transmitting valid time signals due to power failure the clocks will continue to function as accurate quartz clocks until a valid time signal is decoded If signal transmission is not restored after 96 hours the second hand will five step as a visual indicator that the signal has been lost Should the clocks lose power and signal the clocks will not function Specifier Note Analog clock faces can be made with Owner s logo as an option If desired leave in the following and arrange for Owner to provide hard copy or digital copy of logo in format required by Primex Wireless Contact Primex Wireless for details Traditional analog clocks AC Analog clocks shall be wall mounted Clocks shall have polycarbonate frame and polycarbonate lens Face shall be white Hour and minute hands shall be black 12 1 2 inch 317 5mm diameter analog clock 24 VAC Primex Wireless Model 14323 12 1 2 inch 317 5mm diameter analog clock 1
3. attachment to roof structure 16730 7 OANINNFWN KR XR Wireless Clock Systems Division 16730 The GPS Receiver cable must be plenum rated where required by local code Transmitter Specifier Note Select procedure appropriate to the master time source from either of the following Primex Wireless Model XRO1IM suppressor battery backup and a mounting shelf The clock system shall transmit time continuously to all clocks in the system Primex Wireless Model XROIIN consisting of a wireless transmitter surge suppressor battery backup and a mounting shelf Unit shall obtain current NTP time from Ethernet network The clock system shall transmit time continuously to all clocks in the system Transmission Frequency Ranges 72 020 to 72 980 MHz 74 610 to 74 790 MHz 75 210 to 75 390 MHz 75 440 to 75 600 MHz Transmission Power 1 watt 30dBm maximum Radio technology narrowband FM Number of channels 74 Channel bandwidth 20 kHz maximum Transition mode one way communication Data rate 2 KBps Operating range 32 degree F to 158 degrees F 0 degrees C to 70 degrees C Transmitter Transmitter output power 26 to 30 dBm Frequency deviation 4 kHz Transmitter power requirements 120 VAC 60 Hz 16730 8 OANANINDMNBWN KF XR Wireless Clock Systems Division 16730 Internal power requirements 5 VDC Carrier frequency stability 20 ppm Transmitter shall have 74 selectable cha
4. 20 VAC Primex Wireless Model 14306 Additional colors finishes and dial faces are available from manufacturer Analog clocks shall be AC powered 24 VAC or 120 VAC Clocks must have an 18 inch 457 2mm cord with 2 prong plug 9120 VAC or pigtail 24 VAC to connect to power source Analog clocks shall be capable of adjusting for Daylight Saving Time Time shall be automatically be updated from the transmitter 6 times per day If power is interrupted the clock will stop until power resumes Upon resumption of power the clock will self correct to the current time Clocks shall have a tamper proof theft resistant clock lock mounting slots Analog clock receivers shall be as follows Receiver sensitivity gt 110 dBm Receiver power 24 VAC or 120 VAC see model Antenna type internal Antenna gain 7 dBd If transmitter stops transmitting valid time signals due to power failure the clocks will continue to function as accurate quartz clocks until a valid time signal is decoded If 16730 12 OANINMNBWN KF XR Wireless Clock Systems Division 16730 signal transmission is not restored after 96 hours the second hand will five step as a visual indicator that the signal has been lost Should the clocks lose power and signal the clocks will not function Specifier Note Analog clock faces can be made with Owner s logo as an option If desired leave in the following and arrange for Owner to provide hard copy or digita
5. 30 1 OAANINDMNFWN KR XR Wireless Clock Systems Division 16730 Specifier Note Edit the following list as required for the project List other sections with work directly related to this section 1 2 Related Sections Division 16 Electrical 120 volt grounded outlet required for transmitter Division 16735 Wireless Tone Generator Division 16731 Digital Display Clocks and Timers Specifier Note List standards referenced in this section complete with designations and titles This article does not require compliance with standards but is merely a list of those used 1 3 1 4 1 5 References This Technical Specification and Associated Drawings Primex Wireless XR Satellite Time System User Manual Definitions GPS Global Positioning System a worldwide system that employs 24 satellites in an integrated network to determine geographic location anywhere in the world and which employs and transmits Universal Coordinated Time the world s most accurate and reliable time UTC Universal Coordinated Time NTP Network Time Protocol used for synchronizing the clocks on computer networks and devices from either a public server or a separate server on a private local area network System Description XR wireless clock system shall continually synchronize clocks throughout the facility and shall be capable of clock readouts in multiple time zones where desired The system shall provide wireless ti
6. OMANANIDNFWNFR XR Wireless Clock Systems Division 16730 Primex Wireless Inc September 2009 1310 Kerrisdale Blvd Unit 4 Newmarket ON L3Y 8V6 800 330 1459 www primexwireless ca Product Guide Specification Specifier Note This product specification is written according to the Construction Specifications Institute CSI MasterFormat SectionFormat and PageFormat contained in the CSI Manual of Practice The section must be carefully reviewed and edited by the Architect Engineer Consultant to meet the requirements of the project and local building code Coordinate this section with other specification sections and the drawings Delete all Specifier Notes when editing this section DIVISION 16730 XR WIRELESS CLOCK SYSTEMS Specifier Note This section covers the Primex Wireless XR Synchronized Clock System Consult Primex Wireless for assistance in editing this section for the specific application Part 1 General Requirements and Scope Furnish and install a complete new XR wireless clock system using Primex Wireless Inc XR wireless system All bids shall be based on the equipment as specified herein The specifying authority must approve any alternate system Reference Division 16730 Clock Systems Specifier Note Edit the following list as required for the project 1 1 Section Includes Transmission Systems GPS Receiver Primary Transmitter Satellite Transmitter Clocks Analog Digital 167
7. cks shall be fully portable capable of being relocated at any time The system must operate in accordance with a Technical Acceptance Certificate issued under the authority of Industry Canada and the Ministry of Industry This license will be granted to and held by the end user Regulatory Requirements Equipment and components furnished shall be of manufacturer s latest model The end user will hold a license known as a Non Complex Fixed Station Radio License granted by Industry Canada and the Ministry of Industry This license grants the end user protected use for wireless transmission at the designated frequency IC 2365 Application for License to Install and Operate a Radio Station in Canada must be completed and signed by end user prior to license issuance The end user will grant permission for Primex Wireless to apply for the license on their behalf Primex Wireless will provide all documents and technical information to Industry Canada for approval This license will designate a unique call sign for each end user Transmitter and receiver shall comply with RSS 119 of Issue 6 of Industry Canada specifications as follows Equipment and components furnished shall be of manufacturer s latest model The end user will hold a license known as a Radio Station Authorization granted by 16730 3 OANANINNBWN KR XR Wireless Clock Systems Division 16730 1 7 the ICC This license grants the en
8. d defective Cleaning Prior to final acceptance clean exposed surfaces of clocks using cleaning methods recommended by clock manufacturer Remove temporary labels from clock faces Do not remove labels from backs of clocks Demonstration Provide training to Owner s representative on setting and adjusting clocks replacing batteries and routine maintenance Protection Protect finished installation until final acceptance of the project Testing All devices must be tested at their operational location under normal operational conditions to assure reception of signal END OF SECTION 16730 16
9. d user protected use for wireless transmission at the designated frequency This license will designate a unique call sign for each end user Transmitter and receiver shall comply with RSS 119 of Issue 6 of Industry Canada specifications as follows This device may not cause harmful interference and This device must accept interference received including interference that may cause undesired operation Transmitter frequency shall be governed by IC RSS119 Issue 6 Transmitter output power shall be governed by IC RSS119 Issue 6 System shall be installed in compliance with local and state authorities having jurisdiction Submittals Product Data Submit complete catalog data for each component describing physical characteristics and method of installation Submit brochure showing available colors and finishes of clocks Specifier Note In accordance with Industry Canada regulations an application for Technical Acceptance Certificate must be filed prior to use of the equipment Normally the manufacturer will have completed the filing and obtaining the license If not the Owner will be required to file the application with the Industry Canada prior to use Furnishing the license or a copy of the application will confirm that Industry Canada approval has been obtained Operating License Submit evidence of application for IC Radio Station Authorization prior to installing equipment Furnish the license or a cop
10. ence producing GPS wireless time systems Installer Company with documented experience in the installation of commercial time systems Prior to installation a site survey must be performed to determine proper transmitter placement Delivery Storage and Handling Deliver all components to the site in the manufacturer s original packaging Packaging shall contain manufacturer s name and address product identification number and other related information Store equipment in finished building unopened containers until ready for installation 16730 5 OAANINDMNBWN KR XR Wireless Clock Systems Division 16730 1 11 Project Site Conditions Clocks shall not be installed until painting and other finish work in each room is complete Specifier Note Delete following site condition if NTP will be the master time source Coordinate installation of GPS receiver for access to the roof or exterior side wall so that the bracket and related fasteners are watertight 1 12 System Startup At completion of installation and prior to final acceptance turn on the equipment ensure that all equipment is operating properly and that all clocks are functioning 1 13 Warranty Manufacturer will provide a 1 year warranty on GPS receiver transmitter and satellite transmitter All other components will have a 1 year warranty Part 2 Products 2 1 Manufacturer XR wireless clock system shall be manufactured by Primex Wireless Inc
11. ime once every second The transmitter updates its internal clock in this mode once per hour Analog Clock Operation Apply power or insert batteries Follow set up procedures detailed in manufacturer s instructions After initial setup the clock will shut off the receiver Six times each day the microprocessor will activate the receiver and starting with the stored channel it will again look for a valid time signal If necessary the clocks will resynchronize to the correct time If the clock has not decoded a valid time signal for a pre determined number of days it will go to a step mode Low battery voltage is a common cause of the clock to not properly decode a time signal If a clock goes into step mode replace the batteries first and then determine if the clock synchronizes to master time before attempting other troubleshooting methods 2 3 Equipment General The clock system shall include a transmitter indicating clocks and all accessories for complete operation Specifier Note If NTP transmitter package is purchased delete GPS Receiver statement otherwise select extension cable length if applicable GPS Receiver GPS roof mounted with 10 foot cable 3m attached Primex Wireless extension cable available 50ft 15 25m 100 ft 30 5m and 200 ft 61m The GPS Receiver shall be a complete GPS receiver including antenna in a waterproof case designed for roof or outdoor mounting Provide mounting bracket for
12. ing care not to strip threads Connect power supply to the transmitter Connect power supply to the transmitter Set the channel number on the display to correspond to the Industry Canada license Plug power supply into electrical outlet Analog clocks perform the following operations with each clock Set clock to correct time in accordance with manufacturer s instructions Observe analog clock until valid signals are received and analog clock adjusts itself to correct time Install the analog clock on the wall in the indicated location plumb level and tight against the wall If using 12 1 2 inch 317 5mm clock attach using clock lock hanging method and suitable fasteners as approved by clock manufacturer Analog clocks AC Perform the following operations with each clock Observe clock until valid time signals are received and analog clock adjusts itself to correct time 16730 15 OAANINHNDMNBWN RK XR Wireless Clock Systems Division 16730 Install the analog clock on the wall in the indicated location plumb level and tight against the wall Attach using clock lock hanging method and suitable fasteners as approved by clock manufacturer Specifier Note Delete the following if wire guards are not required 3 3 3 4 3 5 3 6 3 7 Wire guards Secure to wall using approved theft resistant fasteners Adjusting Prior to final acceptance inspect each clock adjust as required and replace parts which are foun
13. l copy of logo in format required by Primex Wireless Contact Primex Wireless for details Analog clock faces shall bear Owner s logo as indicated Digital Clocks Primex Wireless Model XRA1B203 6 digit 4 inch 101 6mm 7 segment red LED display Specifier Note Select optional digit style colors and case styles from manufacturer s brochure Digital clocks must be able to receive synchronized time signal from Primex Wireless master or satellite transmitter Digital clocks must have time and date option Digital clocks shall be capable of automatically adjusting for Daylight Saving Time Power Supply 120 VAC 50 60 cycle Digital clocks must be viewable from 150 feet 45 7m Specifier Note Where desired for protection of clocks specify the following optional equipment Wire guards Provide one for each analog clock as follows Analog clock wire guard Primex Wireless Model 14131 14 by 14 inch 355 6 by 355 6 mm size for nominal 12 1 2 inch 317 5 mm diameter analog clocks Analog clock wire guard Primex Wireless Model 14123 18 by 18 inch 457 2 by 457 2mm size for 16 inch 406 4mm diameter analog clocks Digital clock wire guard Primex Wireless Model 14388 for 2 5 inch LED digital clocks Digital wire guard Primex Wireless Model 14389 for 4 inch LED digital clocks 16730 13 OmMANNBPWN XR Wireless Clock Systems Division 16730 Dual D Lithium Battery Pack Primex Wireless Model 14885 contains
14. me from a master time source This time source will either be the atomic clock on the GPS system or the clock from a defined NTP server that the XR transmitter can access via the customer Ethernet The master time will be synchronized to UTC Hard wiring will not be required to the clocks installed for the system Clocks shall automatically adjust for Daylight Saving Time in locations where DST is observed Analog Clocks shall be synchronized to within 10 milliseconds 6 times per day and 16730 2 OANINNHBWNH XR Wireless Clock Systems Division 16730 1 6 the system shall have an internal oscillator that maintains plus or minus one second per day between synchronizations so that clock accuracy shall not exceed plus or minus 0 2 seconds The system shall include an internal clock reference so that failure to detect the master time source shall not result in the clocks failing to indicate time Additionally XR transmitters will have an internal battery backup of up to eight hours in the event of a power failure so that settings and the correct master time will be instantly recalled upon restoration of power The system shall incorporate a fail safe design so that failure of any component shall not cause failure of the system Upon restoration of power or repair of failed component the system shall resume normal operation without the need to reset the system or any component thereof Clock locations shall be as indicated and clo
15. nnels to assure interference free reception Transmitter shall have the following switches Time zone adjustment switches for all time zones in the world Includes all Canadian time zones Atlantic Newfoundland Eastern Central Mountain and Pacific DIP Switch to allow the following configuration Daylight Saving Time bypass option 12 hour or 24 hour display GPS or NTP time source Local or LAN configuration UTC or UTC 30 minute UTC offset option for Newfoundland Transmitter housing shall be black metal case 16 3 4 inches 424 4mm by 12 inches 304 8mm by 1 7 8 inches 46 4mm in size Antenna shall be 46 inches 1168mm high commercial type mounted on top center of transmitter housing Antenna gain shall be lt 2 2 dB Antenna polarization shall be vertical Transmitter housing shall incorporate a display which shall include the following Time readout AM and PM indicator if 12 hour time display is set Day and date readout Time zone indicator including Standard or Daylight Savings Time On screen menu to verify diagnostics errors time updates and switch settings toggled by sequence of push buttons next to display Status LEDs Green which when solid indicates transmitter is broadcasting yellow which flashes in the event of lack of time update after 48 hours red which flashes to indicate connection or internal transmitter problem Internal clock Transmitter shall contain an internal clock such that failure t
16. o update time from source will not disable the operation of the clocks Power supply included Input 120 volt AC 50 60 Hz 0 4 amps Output 9 volt DC 1 5 amps Surge Protector Battery Backup included 16730 9 OAANINDNBWN KR XR Wireless Clock Systems Division 16730 Input 120 volt AC 60 Hz 1 Hz Output 120 volt AC S5O0VA 300 watts Surge Energy Rating 365 joules Additional Equipment Specifier Note Large buildings and multi building projects may require satellite transmitters to provide proper coverage Consult Primex Wireless for assistance in making this determination If satellite transmitters are required include the following two items in the project specification Wireless Receiver Switches Switches shall receive time packets from the Primary Transmitter and relay the synchronized time to the Satellite Transmitter connected to it The unit shall include the following Antenna mounted on top of the switch housing 1 1 1 2 inches 292mm long Power Supply Input 120 VAC 50 60 Hz 0 4 amps Output 9 volt DC 1 5 amps RS 232 data cable 5 feet 1 5mm long Daylight Savings Time bypass switch Dimensions 4 1 4 inches 108mm long 5 3 4 inches 146mm wide 1 1 4 inches 31 75mm deep Weight 12 ounces 34kg Operating Range 32 degrees F to 158 degrees F 0 to 70 degrees C Satellite Transmitters Primex Wireless Model XROIR Satellite Transmitters shall receive the signal from the Wireles
17. rge metal objects such as filing cabinets lockers or metal framed walls Transmitter s will be placed at locations indicated below Specifier Note To assure optimum performance of the XR Wireless Clock System transmitter s location s must be specified in the construction documents Primex Wireless Applications Engineering Dept should be consulted to determine the number and placement of transmitter s required for the project Contact Primex Wireless Technical Support at 1 800 404 8117 OMmAANIDNBWN KR XR Wireless Clock Systems Division 16730 Specifier Note Select procedure appropriate to the master time source from either of the following If GPS Unit will be used as master time source Attach GPS receiver to transmitter using cable Set GPS LAN DIP switch to GPS If NTP will be used as master time source Connect CATS CATSe CAT6 EIA TIA standard Ethernet cable from transmitter LAN port to available network drop Set GPS LAN DIP switch to NTP Specifier Note If NTP is the master time source the network drop used to connect the XR transmitter must have connectivity to the NTP server which can be verified by the customer IT manager The default NTP address is time nist gov If the network has a different NTP IP address it may be programmed into the transmitter by the installer to allow connection to the proper network time Contact Primex Wireless Technical Support at 1 800 404 8117 Connect antenna to transmitter us
18. s Receiver Switches and transmit the signal to the devices in its vicinity which are out of the range from the Master Transmitter The unit shall include the following Antenna mounted on top of the housing 46 inches 1168mm long Wireless Receiver Switch Power Supply Input 120 VAC 50 60 Hz 0 4 amps Output 9 volt DC 1 5 amps 6 foot 1 83m cord 16730 10 OANANINNBWN KR XR Wireless Clock Systems Division 16730 Surge Suppressor Battery Backup Mounting Shelf Transmission Power 1 watt maximum 72 MHz frequency Traditional analog clocks battery Analog clocks shall be wall mounted Clocks shall have polycarbonate frame and polycarbonate lens Face shall be white Hour and minute hands shall be black 9 inch 228 6mm diameter analog clock Primex Wireless Model 14280 12 1 2 inch 317 5mm diameter analog clock Primex Wireless Model 14155 16 inch 406 4mm diameter analog clock Primex Wireless Model 14163 24 inch 610mm diameter analog clock Primex Wireless Model 14346 Additional colors finishes and dial faces are available from manufacturer Analog clocks shall be battery operated Analog clocks shall be capable of automatically adjusting for Daylight Saving Time An on off switch located on the transmitter shall disable this function If desired Time shall be automatically updated from the transmitter 6 times per day Analog clocks shall remember the time during changing of batteries 9 inch 228 6mm
19. two sealed parallel lithium primary batteries Cable Connection Sealant Radio Shack Coaxial Cable Connector Sealant 278 1645 or approved electrical grade silicone sealant Part 3 Execution 3 1 Examination Verify that construction is complete in spaces to receive equipment and that rooms are clean and dry Verify that 120 volt electrical outlet is located within 6 feet 1 83m of location of transmitter and the outlet is operational and properly grounded 3 2 Installation Provide all equipment necessary for a complete and operable system Specifier Note valid for transmitter with GPS input The GPS unit can be mounted on the roof on a pole or at a window In each case the GPS unit must have a clear view of the sky If the GPS unit is mounted on the roof it must be located on a suitable bracket well above the level of standing or incidental water If the GPS unit is mounted at a window it must be located away from low E glass If transmitter to use NTP as source delete following work instruction with this note cable connection to GPS with cable connection sealant Any added cable lengths must be protected from outside elements Specifier Note Where desired for mounting transmitter specify the following equipment One Model Number 14005 18 inches long by 3 inches wide by 15 inches deep Transmitter Locate transmitter where indicated a minimum of 2 to 3 feet 6 to 1 meter above the floor away from la
20. y of the application for the license to the Owner End User prior to operating the equipment The original license must be delivered to the Owner End User Samples Submit one clock for approval Approved sample shall be tagged and shall be installed in the work at location directed 16730 4 OAANINNHBRWNH XR Wireless Clock Systems Division 16730 1 8 1 9 Manufacturer s Instructions Submit complete installation set up and maintenance instructions Floor plans indicating the location of system transmitter s approved by manufacturer will be submitted to owner prior to installation Substitutions Proposed substitutions to be considered shall be manufactured of equivalent materials that meet or exceed specified requirements of this Section Proposed substitutions shall be identified not less than 10 days prior to bid date Other systems requiring wiring and or conduit between master and clocks will not be accepted Other systems using wireless technology in an unlicensed frequency range will not be accepted Other systems using wireless technology where the license is held by any party other than the end user will not be accepted Quality Assurance Permits Obtain operating license for the transmitter from the Industry Canada Qualifications Manufacturer Company specializing in manufacturing commercial time system products with a minimum of 30 continuous years of documented experience including 4 years experi
Download Pdf Manuals
Related Search