USER MANUAL - CARPET EXTRACTOR X17 ECO REV F 0413.pmd
Contents
1. User Manual X17 ECO Carpet Extractor i This manual is furnished with each new Minuteman X17 This provides the necessary operating and preventive maintenance instructions Operators must read and understand this manual before operating or servicing this machine This machine was designed to give you excellent performance and efficiency For best results and minimal cost please follow the general guidelines below Operate the machine with reasonable care Follow the manufacturer s suggested maintenance instructions as provided in this booklet Use original Minuteman supplied parts nen Technical Specifications Model X17 ECO Model No Xizu5 X17115HP X17230 X17230HP Current Max 12 Amps 7 Amps Voltage drev 2307 Vacuum motor power 1250W 1250W Brush motor power 100W 100W Pump motor power 50PSI 100PSI SOPSI 100PSI Working width 17 48cm 17 43cm Gross Weight 110 lbs 110 lbs Solution tank 10 Gallon 37 8 LITERS 10 Gallon 37 8 LITERS Recovery tank 7 Gallon 26 5 LITERS 7 Gallon 26 5 LITERS Cable soft 50 tt Suction sealed 100 in of water 100 in of water Vibration lt 82 ts lt 2 5 mist Noise emission The sound pressure level measured under maximum conditions 83 dB A of use LwA according to DIN EN 60335 2 68 The sound pressure level measured at the ear of the driver under 72 dB A normal conditions of use LpA according to DIN EN 602. du transporteur livreur qui doit tre inform e imm diatement ELECTRICITE 115 Volt Mod les X17115 X17115HP appareils sont congus pour op rer sur un circuit standard de 15 amp 120 volt 60 hz circuit AC Tout voltage en bas de 105 volt AC o au del de 125 volts AC pourrait occasionner des dommages au moteur ELECTRICITE 230 Volt Mod les X17230 X17280HP Ces appareils sont congus pour op rer sur un circuit standard AC de 16 amp fusible type L 230 volt 50 hz Tout voltage en bas de 210 volt AC ou au del de 250 voli AC pourrait occasionner des dommages au moteur AVERTISSEMENT Les moteurs lectriques peuvent tre la cause d explosion si is sont utlis s pr s de mat riaux ou de vapeurs explosives Ne pas op rer pr s de mat riaux inflammables tels que solvant essence poussi re de grain etc INSTRUCTIONS POUR PRISSE DE TERRE Ces appareils doivent poss der une prise de miss terre pour prot ger l op rateur contre les chocs lectriques Cet appareil est muni d une corde lectrique trois fis et d un receptacle trois ourchons et prise de mise tere pour s accorder dans un recep tacle avec prise de mise terre r ciproque Le fil conducteur vert ou vert et jaune de la corde lectrique est le fi design comme prise de mise terra Ne jamais relier ce fi un fil autre que celi de prise de mise tere Instructions de d ballage DANGER Une mauvaise connexion du conducteur de terre
3. Grout breaker in handle tipped Ress breaker Boli is damaged Replace belt is lodged in the Brush housing Remove debris Switch is in OFF 0 position Flip switch to ON position Solution recovery is reduced Dome Id fiter or vac float shut of may be clogged Finse out tems Recovery dome id is nat Seated properly Reposition dome id Recovery Tank is not Seated properly over intake tube Reposition recovery tank so the intake tube is inserted into the inlet Recovery tank dump hase may nat be closed properly Disconnect cap from drain hose then reconnect to ensure the cap and hose snap together Bad seals on recovery dome id Check the gasket on the id Tor damage Replace if needed Vac shoe may be clogged Check vac shoe for debris and remove T necessary Vac shoe may be worn Replace vac shoe Vacuum motor does not start Grout breaker in handle may have tipped Reset breaker Motor carbon brush may be warn Contact a qualified senice technician Switch is in the OFF O Position Flip the switch to the ON l Position 29 e Minuteman International Made Simple Commercial Limited Warranty REVISION F EFFECTIVE 6 1 2009 Minuteman International Inc warrants to the original purchaserluser that the product is free from defects in workmanship and materials under normal use Minuteman wil at its optio
4. Wipe off any debris from O ring under dump hose cap Dome lid should be cleaned Pull or rinse off any debris from the attached Filter Place lid upside down when storing machine for ventilation to prevent odor build up Vacuum shoe should be cleaned of any debris Brush should be cleaned of any carpet string or debris Vac Float Shut off page 12 Item P should be pulled out inspected cleaned if necessary Solution In Line Filter page 16 should be inspected and cleaned if necessary Wheels should be cleaned of hard debris which may damage finished hard surface floors Electrical Cord should be inspected for any damage j Vacuum Hose should be inspected for tight fit at the rear of the machine and to the bottom of the Vac Connection Tube 28 Maintenance BI MONTHLY MONTHLY YEARLY MAINTENANCE EVERY TWO WEEK 1 Purge solution system to remove residue build up by flushing as follows a b c Use 1 quart White Vinegar to two gallons clean hot water in the solution tank operate solution pump with spray jets installed for two full minutes Drain the remaining solution with the solution leveldrain hose this is important to help keep the hose clear Use 2 gallons clean hot water in the solution tank operate solution pump with spray jets installed for two full minutes Drain the remaining water with the solution level drain hose Important Repeat 2 gallon rinse as vinegar may affect coloring in ca
5. days Not o exceed two hours Exception PAS 14B tyr tyr 0 Battery Chargers One year replacement Replacement Parts Ninety days Batteries 0 3 months replacement 4 12 months pro rate Polyethylene Plastic Tanks Tanks have 10yr warranty additional labor 150 4 Wnszz896 jo saqua urueujnunur wwe Ozv6 Gze 008 auod YSN 00109 sioul aeuDuid 02 einod S SBNY leuoneuuenu ueuieinuw UE9 2 oouoj o2x3 Jeuej3nui
6. plastic threads 5 Turn Shut off Valve C counterclockwise to open 16 Ren Machine Overview Solution Tank Drain Hose The solution tank may be drained by removing the Solution Tank Drain Hose A from the Hose Barb B and routing the hose to a floor drain Solution Level Indicator The solution Tank Drain Hose also serves a water level indicator for the solution tank The amount of water remaining in the solution tank can be seen through the clear drain hose 17 Machine Overview ccm Brush Removal Use a 4mm or 5 32 Hex Tool to remove the flat head screw on the underside of the right side of the brush housing Pry open the brush housing door Pull brush straight out to the side To re install Insert the end of the brush with drive lugs first to match the drive hub on the left side Twist the brush until the drive hub locks in to the brush Close the brush housing door The bearing in the door will insert itself into the end of the brush While holding the housing door closed re install flat head screw from the underside of the housing 18 Machine Overview Brush Pressure Gauge The brush pressure gauge informs the operator if the brush pressure setting is in optimum range The machine operates best in the green area If the machine reaches the yellow or red range the brush pressure can be lowered by raising the brush by turning the brush pressure ad
7. 3 SPRAY JET PUMPAUX POWER amp PUMP BREAKER X17115 1 5amp X17230 1 0amp H any of the functions above are not operating check if the circuit breaker buttons have tripped Press to reset Machine Overview Momentary Handle A When handle is pushed forward the spray jets shut off Brush Switch B ON OFF switch for brush Flip switch up to I position to tum on the brush motor Flip switch to o position to shut off brush motor Vacuum Switch C ON OFF switch for vacuum Flip switch up to I position to turn on vacuum Flip switch to position to shut off Spray Jet Auxiliary Switch 0 Power switch for spray jet and auxiliary function Push the switch to the position to turn ON the spray jets Push switch to II position to use the Off aisle wand This will power the auxiliary outlet and will turn the water pump on for the auxiliary connection See page 22 for connection details Make sure to turn off the brush motor when this switch is in the auxiliary mode or damage to carpet may occur 15 Machine Overview Solution Tank In line Filter The In line Filter B should be cleaned regularly To clean 1 Close the Shut off Valve C by turning the handle 90 clockwise 2 Next twist the Filter Cap A counterclockwise 3 Pull the filter out to clean filter and cap 4 Place filter back into cap twist cap clockwise onto filter body tighten by hand Note Using tools to tighten may damage
8. 335 2 68 Measurement inaccuracy KpA 1 848 A The frequency weighted acceleration measured according to DIN EN ISO 5349 which have an effect upon the upper limbs hand arm system amounts under normal working conditions CE Declaration C DECLARATION OF CONFORMITY MANUFACTURER S NAME Minuteman international Inc MANUFACTURER S 14N845 U S Routo 20 ADDRESS Pingree Grove IL 60140 USA EQUIPMENT Electric Carpet Extractor DESCRIPTION EQUIPMENT MODEL x17230 DESIGNATION Application of Council Directives ENG0335 1 ENG0325 2 68 ENSO366 ENT2100 1 EN12100 2 ENSSD14 1 2004 108 EC IECICISPR 14 1 Additional Standards ISO 349 1 ISO 5349 2 the undersigned hereby declare that the equipment spacifiec above conforms othe above Directive and Standards ees zam 7 ac op PRINTED NAME Dean Theobold TITLE Vice President Table Of Contents Machine Overview 12 X17 Back amp Bottom Machine Overview Circuit Breakers Momentary Handle Brush Switch Vacuum Switch 15 Spray Jet Auxil s 15 Solution Tank In ine Filter 16 Solution Tank Drain Hose 17 Solution Level Indicator 117 Brush Removal 18 Brush Pressure Gauge 19 Removable Recovery Tani 20 Cord Relief 21 Handle Adjustment E Accessories 22 Maintenance Operating instructions 26 Troubleshootir 28 juteman International Made Simple Commer Safety Instructions FOR COMMERCIAL USE ONLY IMP
9. G 1 Always work away from the cord 2 Machine operates by pulling backwards over carpet 3 Therecovery dome lid page 12 item B should be properly seated on Recovery Tank item C for proper vacuum recovery 4 See page 14 Control Panel Switch Identifications Normal Cleaning Mode 1 Tum on vacuum switch C Tum on brush switch B Tum on the solution pump D to position 1 Adjust brush pressure at rear of machine until brush pressure gauge reads in green zone Solution pump should be turned off by either using the momentary bail item A or flip the switch spray jet to the center position item D 6 before the end of each cleaning pass 26 Operating Instructions CONTINUED During the cleaning cycle care should be taken not to allow foam to build up in the recovery tank If this should happen the machine should be turned off Defoamer order 4910543 should be added to the recovery tank only never into the solution tank Foam should not be seen inside the right side of the dome lid The recovery water level can be viewed from the operator s position of the machine through the lett side of the visible recovery dome The X17 has a float ball shut off located in the recovery tank that cuts off suction to the vacuum hose When the recovery tank is full the vacuum motor will become noticably louder and the machine will not pick up water Recovery tank must be emptied NOTE Never tilt machine completely back with recovery t
10. ORTANT SAFETY INSTRUCTIONS When using an electrical appliance basic precautions should always be followed including the following READ ALL INSTRUCTIONS BEFORE USING WARNING To reduce the risk of fire electric shock or injury Do not leave appliance when plugged in Unplug from outlet when not in use and before servicing WARNING To reduce the risk of electrical shock do not expose to rai Never allow children or untrained adults to operate this equipment Keep the area of operation clear of all persons particularly small children and pets Keep bystanders at least 25 feet away from the area of operation Use only as described in this manual Use only manufacturers recommended attachments Do not use with damaged cord or plug If appliance is not working as it should has been dropped damaged left outdoors or dropped into water return it to a service center Do not pull or carry by cord use cord as a handle close a door on cord or pull cord around sharp edges or comers Do not run appliance over cord Keep cord away from heated surfaces Donotunplug by puling on cord To unplug grasp the plug not the cord Do not handle plug or appliance with wet hands Do not put any object into openings Do not use with any opening blocked keep free of dust lint hair and anything that may reduce air flow Store indoors Keep hair loose clothing fingers and all parts of body away from openi
11. Solution Hose F to the quick connect Solution Coupling C To tum ON the tool the auxiliary switch in the machine handle must be in the I position as shown on Page 14 Item D The vacuum switch must also be tumed on when using the motorized tool 390070 Upholstery Too Requires Hose Assembly 831255 Scrub Vacuum Wand Requires Hose Assembly 828924 or 830750 Hose assemblies for non motorized tools Do not require QC coupler G 831019 Pump Out Hose 17603 Vac Out Hose Caution Brush motor must be tumad OFF when using auxilary function f the rush molor is ON damage to VN smetmi ooo 22 gt Maintenance USER MAINTENANCE INSTRUCTIONS All service and repairs should be performed by a qualified service representative or electrician No user serviceable components are employed in the electrical assembly No lubrication of the motor is required BEFORE CLEANING OR MAINTAINING THE MACHINE UNPLUG THE ELECTRICAL CORD Protect equipment from freezing Severe pumping system damage can occur if allowed to freeze DAILY MAINTENANCE opnom Solution tank should be emptied after each use Flush solution pump system with 1 gallon of clean hot water Operate for 30 seconds through the spray jets then drain the remaining water with the solution level drain hose Both require flushing for best performance Removable recovery tank should be rinsed clean and drained using dump hose Tank does not need to be removed
12. age des escaliers Ne pas utiliser pour ramasser des liquides infammables ou combustibles tels que l essence ou de dans les zones o is peuvent pr sents Branchez une prise corectement mise la terre Voir les instructions de mise la terre Sila mousse ue sort d ouvertures d chappement toumer teindre imm diatement Utiisez uniquement des produits chimiques recommand s par le distributeur fabricant Get apparel doit re utilis uniquement avec le cordon d alimentation fourni parl fabricant X17115 X17115HP 748613 X17230 X17230HP 748613CE Unpacking Instructions eo INSPECTION Carefully unpack and inspect your machine for shipping damage Each unitis tested and thoroughly inspected before shipment and any damage is the responsibilty of the delivery carrier who should be notified immediately ELECTRICAL Model Numbers X17115 X17115HP are designed to operate on a standard 15 amp 115 vol 60 hz AC circuit Voltages below 105 volts AC or above 125 volts AC could cause serious damage to the motor Model Numbers X17230 X17230HP are designed to operate on a standard 10 amp 230 vot 50 hz AC circuit Voltages below 210 volts AC or above 250 volts AC could cause serious damage to the motor WARNING Electric motors can cause explosions when operated near explosive materials or vapors Do not operate this machine near flammable materials such as solvents thinners fuels grain du
13. ank in place Always remove tank and set to the side before tilting complete machine To empty the recovery tank use the recovery tank dump hose page 13 item D Unclip the hose from the tank and turn the cap a quarter turn counter clockwise and dump waste water into a floor drain slop sink 27 Troubleshooting a 28 Troubleshooting G Caution Unplug power cord before senicing machine components Problem Possible Cause Remedy Power cord may be disconnected at the twist lock or wall outlet Check connections and reconnect i Machine does not function necessary Wall outlet breaker may have Reset breaker Grout breaker in handle tripped Reset breaker Solution tank imine fer valve may be _ Open valve water dispensed from spray jets closed Sprayiet Switch is in OFF 0 or AUX i position Flip sprayjet switch to ON 7 position No water in solution tank Fil solution tank Spray intermittent or streaked Solution hoses may be clogged or kinked Check hose for clogs remove any debris 1 found Replace kinked hase if found Solution Tank inne iter may be clogged Clean strainer thoroughly The spray jets may be clogged Remove the spray tips and clean as required Do not clean out the hole in the jt with a pin or wire This may cause permanent damage dens Troubleshooting Brush does not tum ON
14. en shipped Follow the instruction on page 10 to connect the handle assembly to the machine A HANDLE ADJUSTMENT KNOB B SHOULDER BOLT C COVER D HANDLE ASSEMBLY E SCREW F CORD RELIEF Machine Overview X X17 Front HANDLE B RECOVERY DOME LID C RECOVERY TANK D SOLUTION TANK E SOLUTION TANK FILL PORT F FAUCET FILL HOSE G RECOVERY WINDOW H BRUSH MOTOR BELT COVER VACSHOE Vacuum Connection K VACUUM MOTOR INTAKE COVER L VACUUM CONNECTION TUBE M RECOVERY INLET N HANDLE VACUUM FLOAT SHUT OFF Q RECOVERY WINDOW EXTENSION HOSE R VACUUM MOTOR GASKET 12 en chine Overview X17 Back amp Bottom X17115 TWIST LOCK POWER CONNECTOR SHOWN X17230 POWER CONNECTOR HANDLE ADJUSTMENT KNOB AUXILIARY POWER OUTLET FOR MINUTEMAN MOTORIZED TOOL ONLY RECOVERY TANK DUMP HOSE BRUSH PRESSURE ADJUSTMENT KNOB OFF AISLE WAND WATER FEMALE QUICK CONNECT VACUUM HOSE CONNECTION POINT IN LINE SOLUTION FILTER VAC SHOE BRUSH BRUSH END COVER SPRAY JETS 2 BRUSH MOTOR SOLUTION TANK DRAIN HOSE Q PRECAST OMMSOw B 13 Machine Overview Handle Control Panel A MOMENTARY SPRAY SHUT OFF B BRUSHSWITCH C VACUUM SWITCH D SPRAY JET AUXILIARY SWITCH 14 Circuit Breakers The circuit breakers are located on bottom and rear of the handle assembly 1 BRUSH MOTOR BREAKER X17115 1 5amp X17230 1 0amp 2 VACUUM PUMP BREAKER X17115 12amp X17230
15. ir local distributor for export warranty policies Minuteman is not responsible for costs or repairs performed by persons other than those specifically authorized by Minuteman This warranty does not apply to damage from transportation alterations by unauthorized persons misuse or abuse of the equipment use of non compatible chemicals or damage to property or loss of income due to malfunctions of the product It a dificulty develops with this machine you should contact the dealer from whom it was purchased This warranty gives you specific legal rights and you may have other rights which vary from state to state Some states do not allow the exclusion or limitation of special incidental or consequential damages or limitations on how long an implied warranty lasts so the above exclusions and limitations may not apply to you 30 Se Cord Electric Group Three years parts two years labor ninety days travel Not to exceed two hours Exceptions Model Parts Labor Poly Travel Port A Scrub Tyr Gmonhs 10yrs 0 MPV 13 0 o o MPV 14 818 2ys o o V Series Upright Vacuums dx o o Rapid Air Blower dy tyr toys 0 Explosion Proof Vacuum dy D o X12 X12H amp TRS 14 dy ayr toys 0 E17 amp E20 Electric Scrubbers 1yr Gmonths 10yrs 0 Pneumatic Vacuums 3y ay o o Description Parts Labor Poly Travel Battery Operated Group 3ys 2ys 10 90 days Sweepers iy iy 90 days Internal Combustion Group iy dy 30 90
16. is damaged replace immediately Do not use with damaged cord or plug If appliance is not working as it should has been dropped damaged left outdoors or dropped into water return to service center Do not pull or carry by cord use cord as handle close a door on cord or pull cord around sharp edges or corners Do not run appliance over cord Keep cord away from heated surfaces Do not unplug by pulling cord To unplug grasp the plug not the cord Do not handle plug or appliance with wet hands This equipment should be stored indoors and not exposed to rain 25 Operating Instructions OPERATING INSTRUCTIONS Maximum Water Temperature FILLING THE X17 Remove clear solution cover lid from front of machine or use the supplied faucet fill hose by pulling hose out and holding rubber inlet against faucet Fill solution tank with desired amount of warm water and add liquid cleaning chemical Minuteman Extraction Shampoo order 902163 Gee instructions on container for proper dilutions DO NOT USE powdered cleaning chemicals Powders are unlikely to dissolve thoroughly resulting in clogging the inline solution strainer and other fitings This can reduce or stop solution flow to the pump and spray jets Carpet should be thoroughly vacuumed and obstacles relocated before beginning the cleaning cycle Heavy trafic lane areas should be pre treated or spotted with Minuteman Pre Treat order 902183 for best results TO BEGIN CLEANIN
17. justment knob counter clockwise 19 Machine Overview Removable Recovery Tank To remove tank 1 Unelip dump hose from solution tank 2 Pull recovery tank straight up To replace tank 11 Feed dump hose through opening in solution tank 2 Lower tank into place Recovery vacuum inlet will rest on vacuum connection tube See page 12 items L amp 3 Clip dump hose to solution tank 20 Handle Adjustment The X17 handle was designed with operator comfort in mind The angle position of Ihe handle can be adjusted to suit the needs of the operator Angle Adjustment The handle can be adjusted without tools by loosening the Handle Adjustment Knob A and rotating the handle to the desired position Cord Relief Use cord relief to prevent cables from disconnecting Lock the cord in place by looping the cable and threading the cable through the relief then pull the cable down so it locks into place as shown in figure 2 21 Machine Overview cmm Accessories X17115 46300 00 Motorized Tool X17230 46300 02 Motorized Tool Only this tool may plug into the Auxiliary Power B The vacuum hose as shown on Page 13 G must be first disconnected from the machine back panel Connect the Suction Hose 0 tool o the Vacuum Inlet A Connect the tool Power Cord E to the Auxiliary Power B A Coupler Quick Connect 8 pin 450295 is required to connect the tool
18. lrement Jes petits enfants et les animaux domestiques Garder les badauds au moins 25 m tres de la zone d op ration Utiisez uniquement comme d crit dans ce manuel Utilise uniquement les accessoires recommand s par le fabricant Ne pas utiliser le cordon ou la fiche est endommag Si l appareil ne fonctionne pas comme iI le devrait sil a t chapp endommag laiss l ext rieur o tomb dans l eau le retoumer un centre de service Ne pas tirer ou transporter par le cordon utile le cordon comme une poign e fermer une porte sur le cordon ou firer le cordon autour des ar tes Vives ou des coins Ne pas faire rouler l appareil sur le cordon Gardar le cordon oi des surfaces chauff e Ne pas d brancher en trant sur le cordon Pour d brancher saisir la fiche et non le cordon Ne manipulez pas la fiche ou l appareil avec les mains Ne placez pas d objet dans les ouvertures Ne pas utiiser avec des ouvertures sont bloques garder exempt de poussi re les peluches les cheveux et tout CONSERVEZ CES RECOMMANDATIONS ce qui peut r duire l coulement d air Garder les cheveux les v tements amples les doigts et toutes les parties du corps loign s des ouvertures et des pi ces mobiles Ne pas ramasser tout ce qui br le ou qui fume comme des cigarettes des allumettes ou des cendres chaudes teindre toutes les commandes avant de d brancher Faire preuve de prudence lors da nettoy
19. n repair or replace without charge parts that fail under normal use and service when operated and maintained in accordance with the applicable operation and instruction manuals All warranty claims must be submitted through and approved by factory authorized repair stations This warranty does not apply to normal wear orto items whose life is dependent on their use and care such as belts cords switches hoses rubber paris electrical motor components or adjustments Parts manufactured by Minuteman are covered by and subject to the warranties and or guarantees of their manufacturers Please contact Minuteman for procedures in warranty claims against these manufacturers Special warning to purchaser Use of replacement filters and or prefillers not manufactured by Minuteman or its designated licensees will void all warranties expressed or implied A potential health hazard exists without original equipment replacement All warranted items become the sole property of Minuteman or its original manufacturer whichever the case may be Minuteman disclaims any implied warranty including the warranty of merchantability and the warranty of fitness for a particular purpose Minuteman assumes no responsibilty for any special incidental or consequential damages This limited warranty is applicable only in the U S A and Canada and is extended only to the original user purchaser of this product Customers outside the U S A and Canada should contact the
20. ngs and moving parts Do not pick up anything that is burning or smoking such as cigarettes matches or hot ashes Tum off al controls before unplugging Use extra care when cleaning on stairs Do not use to pick up flammable or combustible liquids such as gasoline or use in areas where they may be present Connect to a properly grounded outlet only See grounding instructions If foanvliquid comes out of exhaust openings turn switch off immediately Use only chemicals recommended by dealer manufacturer This machine must be used only with the power supply cord provided from the manufacturer XITIIS X17115HP 748613 X17230 X17230HP 748613CE SAVE THESE INSTRUCTIONS Consignes de s curit POUR USAGE COMMERCIAL SEULEMENT MODE D EMPLOI SECURITAIRE Lorsque utilise un apparel lectrique des pr cautions de base doivent toujours tre suivies telles que BIEN LIRE LE MODES D EMPLOI AVANT USAGE AVERTISSEMENT Pour r duire les risques de feu choc lectrique ou blessure Ne pas quitter l appareil lorsque la prise de courant est branch e D brancher de la sortie lectrique lorsque la machine n est pas en usage ou pour en fare le service AVERTISSEMENT Pour r duire le risque de choc lectrique Ne pas exposer la pluie Entreposer l int rieur Ne laissez jamais des enfants ou des adultes non form s utiliser cet quipement Gardez l endroit d op ration d gag de toutes les personnes particu
21. peut entrainer un risque de choc lectrique Consultez un lectricien qualifi ou une personne de service si vous avez des doutes quant savoir si la prise est correctement mise la terre Ne pas modifier la fiche fournie avec l appareil si elle ne rentre pas dans la prise une prise ad quate par un lecticien qualifi Mod les X17115 X17115HP sont pour une utiisation sur un circuit nominal de 115 volts et a une fiche de tere qui ressemble la fiche du croquis A Mod les X17230 X17280HP sont pour une utilisation sur un circuit nominal de 230 volts et a une fiche de terre qui ressemble la fiche du croquis Assurez vous que l appareil est branch une prise ayant la m me configuration que la fiche Aucun adaptateur ne doit tre utilis e avec cet apparel ES Unpack machine Use philips screwdriver to Insert handle assembly in Align the teeth on the unscrew 4 screws and between bushings Insert bushing and handle assem remove cover the shoulder bolt through the bly before tightening the bushing and screw into the handle assembly using supplied wrench adjustment knob p Spin the adjustment knob tach the wire harness clockwise to tighten to the machine he wire harness must be aligned with the patterns on the connector to fit Screw the cover back with the 4 screws 10 Assembly HANDLE ASSEMBLY The X17 Handle Assembly D is not assembled on the machine wh
22. rpet Repeat procedure if machine has not been flushed daily 2 Remove Brush page 18 clean any debris off brush hubs at both ends 3 Wipe off any debris from bottom side of chassis 4 Rinse off the Dome Lid Filte MONTHLY 1 Check Spray Jets for full width spray pattern Remove twist orange cap 4 turn counter clockwise and clean with soft bristle brush if necessary Do not use pins or wire which can damage the spray tip 2 Clean the Recovery Window page 12 item G by removing 2 screws and wiping out with a soft cloth use hot water and white vinegar or gentle detergent Take care not to damage the gasket o 24 Inspect Gasket for cracks damage pena Maintenance 3 Flush out Recovery Window Extension Hose page 12 item O while Recovery Window is removed by pouring water vinegar solution through the hose Rinse with clear water 4 Clean off any debris from the Vac Connection Tube amp Recovery Inlet page 12 items L M 5 Clean amp Inspect Vacuum Motor Gasket page 12 item R for damage and ensure Vac Motor Cover page 12 item K is in place 6 Inspect Brush Motor Belt for wear page 12 item Replace if necessary YEARLY 1 Have a qualified service technician check the vacuum motor carbon motor brushes once a year or after every 500 operating hours CORD STORAGE The X17 is supplied with a detachable cord for ease of storage Regularly inspect cord for signs of damage If cord
23. st etc GROUNDING INSTRUCTIONS This floor finishing machine shall be grounded while in use to protect the operator from electric shock The machine is provided with a three conductor cord and a three contact grounding type attachment plug to fit the proper grounding type receptacie The green or green and yellow conductor in the cord is the grounding Wire Never connect his wire to other than the grounding pin of the attachment plug 8 DANGER Improper connection of the equipment grounding conductor can resultin a risk of electric shock Check with a qualified electrician or service person i you are in doubt as to whether the outlet is propery grounded Do not modify the plug provided with the appliance if it will ot fit the outlet have a proper outlet installed by a qualified electrician Model Numbers X17115 X1711SHP are for use on a nominal 115 volt circuit and has a grounding plug hat looks like the plug illustrated in sketch A Model Numbers X17230 X17230HP are for use on a nominal 230 0 circuit and has a grounding plug that looks like the plug illustrated in sketch B Make sure that the appliance is connected to an outlet having the same configuration as the plug No adapter should be used with this appliance INSPECTION Deval e inspectez soigneusement or machine en cas de dommages d exp dition Chaque unit est test e et soigneusement inspect avant exp dition ainsi que tout dommage est de la responsabilit
Download Pdf Manuals
Related Search