CodiSys ™ - Elprosys
Contents
1. power supplied from an electric grid module 220V AC or directly from automotive electric installation 12V DC no need to solder cables inside the dashboard on exception of mileage counters that have inaccessible programmable circuits e g Mitsubishi Lancer handling of programmable circuits does not depend on clock rate of a supervising computer and a set of chips installed on the computer motherboard a number of persons can use the software every user has his her own password and all the actions performed by that person are recorded in the system log updated versions of software are delivered free of charge via the Internet the system files are protected from unauthorised use in other systems 2 Hardware requirements The CodiSys has the following hardware requirements PC compatible computer with installed WINDOWS operation system or newer 20 MB free space on a hard disk free RS 232 port parallel printer s port CENTRONICS a printer may be connected 3 Content of the CodiSys package user s manual CodiProglI programmer 14 pin clips SMD 8 pin clips SMD 8 pin clips DIP BMW adapter Green Codistecker BMW adapter Brown White Blue Black Codistecker BMW adapter SW17 power supplying cable 12V power supply unit 220VAC 12VDC hardware key HASP connecting cable RS232 standard licence agreement 4 Markers and speci2. o ELPROSYS Automotive electronics programming chip tuning 41 800 Zabrze 94 Wolno ci St phone 48 32 376 1 376 fax 48 32 376 1 375 www elprosys com pl e mail office elprosys com pl tts amen Came FS Rome gt R BE CodiSys Abbreviated system user s manual Elprosys Automotive electronics programming chip tuning 41 800 Zabrze 94 Wolno ci St 94 phone 48 32 376 1 376 fax 48 32 376 1 375 WRAZ 2 w po I ey Contents DOREB oie senor E z SPRA GA R GE A kaca 4 Hardware requirements acid 4 Content of the CodiSys package dance 4 Markers and special signs used in the TER cod 4 Connection of the programming programmer and the hardware A EEEE N E E a pts E ET E E E ein detuashant vate 5 a a OE EAT AYN 5 Modification of mileage indicated on a dashboard 1122111111 5 Modification of the dashboard serial number e ssuuaaaasaaaanas 7 Backup copies of IAL TA ooo eo 7 The method of programming loops accounting for the limited ei E E E E E E E ri ata igen A A E 8 Elprosys Automotive electronics programming chip tuning 2 41 800 Zabrze 94 Wolno ci St 94 phone 48 32 376 1 376 fax 48 32 376 1 375 Elprosys Automotive electronics programming chip tuning 41 800 Zabrze 94 Wolno ci St 94 phone 48 32 376 1 376 fax 48 32 376 1 375 1 Features possibility to use the programmer in open area
3. 32 376 1 375
4. be depressed in this way the operators confirms making a record about mileage counter failure The system shall automatically make a copy in a directory folder FAILURES AWARIE that contains information about failures and launches the mileage counter programming procedure After shutdown the CodiProgll program the application is ready to perform the next programming operation or the user is informed about possible errors during data writing RER In order to avoid troubles or data loss it is indispensable to remember that the system must cleaned and every remain of paints and other insulating materials that may cause lack of electric contact have to be removed After the programmer completes reading data from the mileage counter the system must automatically recognize correct value of mileage 0 otherwise or in any doubts the user must contact the licence provider Neglecting or non obedience to this instruction may cause damage of the dashboard Elprosys Automotive electronics programming chip tuning 6 41 800 Zabrze 94 Wolno ci St 94 phone 48 32 376 1 376 fax 48 32 376 1 375 BE The read write voltage used by the programmer should be as low as possible However is an old dashboard is to be programmed one has to apply medium or high programming voltage since the circuit can cause problems during programming While connecting the coupling clip to the programmed
5. is unaltered the unsuccessful programming operations will be not accounted by the licence provider If the CodiSys3 log file is damaged the licence provider shall account programming loops and charge according to the CodiProg II indications However the programming operations which are not one hundred percent positive will not be counted up by the system Settling accounts with the licence provider can be carried out in two ways The first method is a direct visit of the Elprosys company s representative at the premises of the licence owner The second way is the remote settlement It is possible via the Internet fax or telephone The squaring procedure looks like as follws a the system administrator from the user s company sends the file CodiSys3 log to the e mail address mariusz najmowicz elprosys com pl b possible errors and program messages that have occurred during unsuccessful programming operations should be registered and sent to the fax number 48 32 376 1 375 c after receiving the file or the fax the licence provider determines the number of programming operation that are not to charged and deducts from the total number for which the licence is granted and must be paid such information shall be passed to the company s system administrator by phone d the sum for the licence fee should by paid by bank transfer or postal order e one has send a copy of payment receipt to the fax number 48 32 376 1 37
6. 5 f an employee from the ElproSys company shall disclose password to unlock the programmer g after resetting of the programming loop counter by means of the CodiRes program the old CodiSys3 log file should be deleted then the software shall create a new log file which is necessary for further settlement In case of a failed unsuccessful programming procedure but registered within the programmer the user is obliged to inform the employee of the ElproSys company about the event ifa direct telephone contact is impossible at the moment note the following information Czy nienaruszony nie naruszony ort oznacza brak uszkodzenia czy brak modyfikacji pliku Elprosys Automotive electronics programming chip tuning 8 41 800 Zabrze 94 Wolno ci St 94 phone 48 32 376 1 376 fax 48 32 376 1 375 a current time b current date c mileage counter type i e producer car make HW version SW version d all the data of the programmable circuit e make the second data readout from the programmable circuit does not refer to the car makes from the list f if possible check whether the mileage counter of the vehicle works correctly and contains appropriate data in the car The programmer and accompanying equipment are covered by one year long warranty Elprosys Automotive electronics programming chip tuning 9 41 800 Zabrze 94 Wolno ci St 94 phone 48 32 376 1 376 fax 48
7. al signs used in the text The mark denotes a passage that contains information which is extremely important and special attention should be paid to it Neglecting the instruction or inaccurate obedience to it may result in to serious and unalterable damage The mark denotes a passage that contains a significant information Elprosys Automotive electronics programming chip tuning 4 41 800 Zabrze 94 Wolnosci St 94 phone 48 32 376 1 376 fax 48 32 376 1 375 5 Connection of the programming programmer and the hardware key In order to install both the programmer and the hardware authorization key HASP one has to carry out the following actions switch the computer off plug in the hardware key to the parallel printer port LPT the printer may be connected to the other side of the key connect the CodiProgll programmer to a free serial port COM connect power supplying voltage to the programmer switch the computer on 6 First run In order to install the software the user has to run the installation program setup exe After having installation completed the computer has to be restarted The CodiChange program must be run as the first one Please enter the user_name Admin to the user box and the system administrator s password which is provided along with the licence agreement must be typed in the password box Next a configuration window shall be
8. circuit power supply voltage of the whole system must be switched off jo The dashboard under programming should be disconnected from the car installation The programmed circuit shall be energised from the CodiProg II appliance 8 Modification of the dashboard serial number For the current version of software modification of the dashboard serial number is possible only for BMW car makes In order to change the serial number one has to run the CodiChange exe program Having been logged in it is necessary to press F3 key Then selection of an applicable car make is carried out and after depressing the Next Dalej button the program is prepared to programming procedure For this a coupling clip should be carefully placed on the programmable circuit When done confirm by pressing the OK button After depressing the OK button the CodiProg II programmer shall be activated and data reading from the mileage counter is possible After shutdown the CodiProgll program in case of the correct readout the CodiChange program shall display the current serial number of the dashboard A new serial number should be entered five last digits or seven characters digits and letters that are the same as in the car chassis number and accepted by pressing the Execute Wykonaj button The system shall automatically make a copy in a directory folder FAILURES AWARIE that contains information about failu
9. displayed The widow demands to set up the following parameters number of the serial port COM to which the CodiProgll is connected maximum correct mileage authorised users names and passwords the boxes for old passwords have to be left empty After filling the table the data has to be accepted by clicking the button Confirm changes Zatwierdz zmiany then terminate the program by closing its window e g Alt F4 shortcut Now the CodiProg program should be launched First it is necessary to get logged in For that purpose the user has to enter his her name and password the both were record in the previous program After successful completion the login procedure the option About the program O programie from the Help Pomoc menu Unless the program displays the message Communication error occurred Nast pi b d komunikacji the system is ready to operation If communication has not been established one should check connections contacts and wiring or use another serial COM port of the computer the appropriate serial port can be selected using the F6 key Inside the box Maximum correct mileage the minimum possible value should be entered In case of servicing a car which mileage exceeds the value shown in the box the previously set value should be incremented at least to the number of kilometres indicated by the mileage counte
10. he option Search Wyszukiwanie can be selected however that option shall not be described in this manual it is an option for advanced users In case in the option 1 is selected the appropriate type of coding is sought therefore one has to move to the box where a new mileage value should be entered the number can be expressed either in kilometres or in miles After correct input of data values the button Execute Wykonaj should be depressed in this way the operators confirms making a record about mileage counter failure The system shall automatically make a copy in a directory folder FAILURES AWARIE that contains information about failures and launches the mileage counter programming procedure After shutdown the CodiProgll program the application is ready to perform the next programming operation or the user is informed about possible errors during data writing In the operator selects the option 2 he must be absolutely sure about the dashboard type the value of current mileage should be entered That number must be given as accurately as possible because it will be added to the list of mileage values If the real mileage is unknown the number 999999 is to be entered In the following the button Next Dalej should be depressed and one can select from the list such a mileage value which is the closest to the desired number Then the button Execute Wykonaj should
11. r being corrected Standard value for that box is 400 000 km 7 Modification of mileage indicated on a dashboard In order to alter mileage indication one has to run the CodiChange program After having been logged in the F2 key should be depressed then selection of an appropriate Elprosys Automotive electronics programming chip tuning 5 41 800 Zabrze 94 Wolno ci St 94 phone 48 32 376 1 376 fax 48 32 376 1 375 programmable circuit is to be carried out Next the readout voltage must be defined The operator decides whether the circuit uses pull up resistors As far as possible the entered information shall be assisted and completed by the program itself After setting up the above parameters the next steps can be executed The operator carefully connects a clip to the programmable circuit and approves the operation by depressing the OK button After confirming selections and clicking OK the CodiProgll programmer shall be activated and data from the mileage counter shall be read After readout completion and closing the CodiProgll program of the data from the counter are read correctly the CodiChange software moves to automatic recognizing of mileage coding method Depending of the dashboard type the three options are available 1 Selection of automatic recognition of mileage The mileage counter is known for sure hence the List Lista option is activated 3 Incase of a new model of mileage counter t
12. res and launches the new serial number programming procedure After shutdown the CodiProgll program the application is ready to perform the next programming operation or the user is informed about possible errors during data writing 9 Backup copies of primary data For safety the CodiChange program makes backup copies from the factory made dashboard The copies are located in the FAILURES AWARIE The data are stored in the following format date of programming year month day tome of operation hour minute second car make and coding method In case when using backup copied gets necessary one has to choose an appropriate item from the list and click the Execute Wykonaj button Connect the coupling clip and place it over the circuit that is to be programmed Accept the consecutive dialogue box depressing OK each time The CodiChange program shall call the CodiProg II programmer and the previous data shall be restored Elprosys Automotive electronics programming chip tuning 7 41 800 Zabrze 94 Wolno ci St 94 phone 48 32 376 1 376 fax 48 32 376 1 375 10 The method of programming loops accounting for the limited version The number of programming loops is registered and displayed by the CodiProg II software However that indication may count up unsuccessful and partially uncompleted programming operation along with the correct ones In such a case if the CodiSys3 log file
Download Pdf Manuals
Related Search