USER MANUAL - Kramer Electronics
Contents
1. ALL OTHER WARRANTIES REMEDIES AND CONDITIONS WHETHER ORAL OR WRITTEN EXPRESS OR IMPLIED TO THE MAXIMUM EXTENT PERMITTED BY LAW KRAMER ELECTRONICS SPECIFICALLY DISCLAIMS ANY AND ALL IMPLIED WARRANTIES INCLUDING WITHOUT LIMITATION WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE IF KRAMER ELECTRONICS CANNOT LAWFULLY DISCLAIM OR EXCLUDE IMPLIED WARRANTIES UNDER APPLICABLE LAW THEN ALL IMPLIED WARRANTIES COVERING THIS PRODUCT INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE SHALL APPLY TO THIS PRODUCT AS PROVIDED UNDER APPICABLE LAW IF ANY PRODUCT TO WHICH THIS LIMITED WARRANTY APPLIES IS A CONSUMER PRODUCT UNDER THE MAGNUSON MOSS WARRANTY ACT 15 U S C A 2301 ET SEQ OR OTHER APPICABLE LAW THE FOREGOING DISCLAIMER OF IMPLIED WARRANTIES SHALL NOT APPLY TO YOU AND ALL IMPLIED WARRANTIES ON THIS PRODUCT INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR THE PARTICULAR PURPOSE SHALL APPLY AS PROVIDED UNDER APPLICABLE LAW Other Conditions This limited warranty gives you specific legal rights and you may have other rights which vary from country to country or state to state This limited warranty is void if i the label bearing the serial number of this product has been removed or defaced ii the product is not distributed by Kramer Electronics or iii this product is not purchased from an authorized Kramer Electronics reseller If you are unsure whether a reseller is an authorize2. Electronics to perform substantially the same function as the original product 3 Issue a refund of the original purchase price less depreciation to be determined based on the age of the product at the time remedy is sought under this limited warranty What Kramer Electronics will not do Under This Limited Warranty If this product is returned to Kramer Electronics or the authorized dealer from which it was purchased or any other party authorized to repair Kramer Electronics products this product must be insured during shipment with the insurance and shipping charges prepaid by you If this product is returned uninsured you assume all risks of loss or damage during shipment Kramer Electronics will not be responsible for any costs related to the removal or re installation of this product from or into any installation Kramer Electronics will not be responsible for any costs related to any setting up this product any adjustment of user controls or any programming required for a specific installation of this product How to Obtain a Remedy under this Limited Warranty To obtain a remedy under this limited warranty you must contact either the authorized Kramer Electronics reseller from whom you purchased this product or the Kramer Electronics office nearest you For a list of authorized Kramer Electronics resellers and or Kramer Electronics authorized service providers please visit our web site at www kramerelectronics com or contact the Kramer Electro
3. does not cover cartons equipment enclosures cables or accessories used in conjunction with this product Without limiting any other exclusion herein Kramer Electronics does not warrant that the product covered hereby including without limitation the technology and or integrated circuit s included in the product will not become obsolete or that such items are or will remain compatible with any other product or technology with which the product may be used How Long Does this Coverage Last One year as of this printing please check our Web site for the most current and accurate warranty information Whois Covered Only the original purchaser of this product is covered under this limited warranty This limited warranty is not transferable to subsequent purchasers or owners of this product What Kramer Electronics will do Kramer Electronics will at its sole option provide one of the following three remedies to whatever extent it shall deem necessary to satisfy a proper claim under this limited warranty 1 Elect to repair or facilitate the repair of any defective parts within a reasonable period of time free of any charge for the necessary parts and labor to complete the repair and restore this product to its proper operating condition Kramer Electronics will also pay the shipping costs necessary to return this product once the repair is complete 2 Replace this product with a direct replacement or with a similar product deemed by Kramer
4. KRAMER ELECTRONICS LTD USER MANUAL MODELS 610T Detachable Optical DVI Transmitter 610R Detachable Optical DVI Receiver P N 2900 000152 Rev 8 Contents 1 Introduction 2 Getting Started 2 1 Achieving the Best Performance 2 2 Safety Instructions 2 3 Recycling Kramer Products 3 Overview 3 1 Your Detachable Optical DVI Transmitter Receiver 4 Using the Detachable Optical DVI System 4 1 Capturing the EDID 4 2 Connecting the Detachable Optical DVI Transmitter Receiver 4 3 Avoiding Pitfalls with the 610T and 610R 5 Technical Specifications Figures Figure 1 610 Detachable Optical DVI Transmitter and Receiver Figure 2 The Auto EDID Button on the 610T Figure 3 Connecting the Fiber Optic Cables Figure 4 Connecting the 610T 610R Detachable Optical DVI Transmitter Receiver O ONDOA OF VONN o NNA Introduction Welcome to Kramer Electronics Since 1981 Kramer Electronics has been providing a world of unique creative and affordable solutions to the vast range of problems that confront the video audio presentation and broadcasting professional on a daily basis In recent years we have redesigned and upgraded most of our line making the best even better Our 1 000 plus different models now appear in 14 groups that are clearly defined by function GROUP 1 Distribution Amplifiers GROUP 2 Switchers and Routers GROUP 3 Control Systems GROUP 4 Format Standards Converters GROUP 5 Range Exte
5. R OPERATING TEMPERATURE 0 to 40 C 32 to 104 F STORAGE TEMPERATURE 40 to 70 C 40 to 158 F HUMIDITY 10 to 90 RHL non condensing DIMENSIONS 3 8cm x 7 2cm x 1 9cm 1 5 x 2 83 x 0 75 W D H WEIGHT 0 14kg 0 31lbs approx INCLUDED ACCESSORIES 2 power supplies Specifications are subject to change without notice at http Awww kramerelectronics com 610T 610R Technical Specifications LIMITED WARRANTY The warranty obligations of Kramer Electronics for this product are limited to the terms set forth below Whatis Covered This limited warranty covers defects in materials and workmanship in this product What is Not Covered This limited warranty does not cover any damage deterioration or malfunction resulting from any alteration modification improper or unreasonable use or maintenance misuse abuse accident neglect exposure to excess moisture fire improper packing and shipping such claims must be presented to the carrier lightning power surges or other acts of nature This limited warranty does not cover any damage deterioration or malfunction resulting from the installation or removal of this product from any installation any unauthorized tampering with this product any repairs attempted by anyone unauthorized by Kramer Electronics to make such repairs or any other cause which does not relate directly to a defect in materials and or workmanship of this product This limited warranty
6. chable Optical DVI Transmitter Receiver Avoiding Pitfalls with the 610T and 610R If any of these problems occur we recommend the following If the display device shows only a black screen e Check that all the AC and DC plugs and jacks used by the external power supplies are firmly connected e Check that the DVI ports are firmly plugged into the computer and the display device and be sure that the transmitter and receiver modules are correctly plugged into the computer and display device respectively e Check if the computer and display are powered ON and properly booted e Reset the system by unplugging and then replugging the transmitter DVI port or receiver DVI port and then reboot the system If the screen is distorted or displays noise e Check if the graphics resolution is properly set e Goto the Display Properties of Windows and check the settings 610T 610R Using the Detachable Optical DVI System e Be sure that the resolution is set for WUXGA 1920 x 1200 at 60Hz or lower e Reset the system e Disconnect and reconnect the optical DVI cables Be sure that at all times the cables are stored and used away from liquid or dirt 610T 610R Using the Detachable Optical DVI System Eee 5 Technical Specifications INPUTS DVI IN 610T 4 LC optical connectors 610R OUTPUTS 4 LC optical connectors 610T DVI OUT 610R RESOLUTION Up to WUXGA 60Hz 1 65Gbps POWER SOURCE 5V DC 240mA max 610T 390mA max 610
7. d Kramer Electronics reseller please visit our Web site at www kramerelectronics com or contact a Kramer Electronics office from the list at the end of this document Your rights under this limited warranty are not diminished if you do not complete and return the product registration form or complete and submit the online product registration form Kramer Electronics thanks you for purchasing a Kramer Electronics product We hope it will give you years of satisfaction For the latest information on our products and a list of Kramer distributors visit our Web site where updates to this user manual may be found We welcome your questions comments and feedback Web site www kramerelectronics com KRAMER E mail info kramerel com ite of Tastitu Quality amp Control SAFETY WARNING T Disconnect the unit from the power supply before opening and servicing P N 2900 000152 Rev 8
8. er connectors Compliance with the limits for a Class A digital device pursuant to part 15 and 2 of FCC and CE External power adapter supplied or 5V DC from source NanoTools size The Kramer 610T can be powered either by an external power adapter or internally by the 5V pin on the DVI card of the computer The 610T automatically detects if it is being powered via the external power adapter and if so the internal power supply is cut off The 610R module must always be powered by the power adapter Most laptops require that the external power adapter is used for the transmitter 3 1 Your Detachable Optical DVI Transmitter Receiver Figure 1 illustrates the 610T and 610R detachable optical DVI extension system DVI Connector Indication LED Power Adapter Optic Connector Optic Cable Figure 1 610 Detachable Optical DVI Transmitter and Receiver 610T 610R Overview Sa 4 4 1 Using the Detachable Optical DVI System This section describes how to e Capture the EDID of the display device see Section 4 1 e Connect the detachable optical DVI transmitter and receiver see Section 4 2 e Troubleshooting the 610T and 610R see Section 4 3 Capturing the EDID The 610T and 610R are connected via four channels that transmit R G B and clock signals The EDID of the display device is captured onto the transmitter for the computer to read You can capture the EDID of the display device on the 610T so that w
9. hen the computer connects to the 610T it will read the virtual EDID information and identify the display device This procedure is performed only once for the connected display device After storing the EDID the system can be connected and disconnected without having to set the EDID again If the display device is replaced the new EDID should be set on the 610T transmitter To capture the EDID of a display device do the following 1 Connect the 5V power adapter to the power socket of the 610T and connect the adapter to the mains electricity The Indication LED lights 2 Push the Auto EDID button illustrated in Figure 2 using a thin screwdriver 3 Connect the 610T unit directly to the display device The Indication LED flashes several times while reading the EDID 4 When the Indication LED stops flashing disconnect the power 5 Disconnect the 610T The EDID information is now stored and the Indication LED is on 610T 610R Using the Detachable Optical DVI Systen 4 2 610T 610R Using the Detachable Optical DVI System mor Figure Con Feb HED Prak 2 The Auto EDID Button on the 610T necting the Detachable Optical DVI Transmitter Receiver To connect the 610T Detachable Optical DVI Transmitter with the 610R Detachable Optical DVI Receiver as the example in Figure 4 illustrates do the follow ing Set the EDID of the display device see Section 4 1 Plug the 610T DVI co
10. ll or incineration by requiring it to be collected and recycled To comply with the WEEE Directive Kramer Electronics has made arrangements with the European Advanced Recycling Network EARN and will cover any costs of treatment recycling and recovery of waste Kramer Electronics branded equipment on arrival at the EARN facility For details of Kramer s recycling arrangements in your particular country go to our recycling pages at Attp www kramerelectronics com support recycling 610T 610R Getting Started Overview The 610T and 610R are a detachable optical transmitter and receiver pair for sending DVI signals with resolutions of up to 1920x1200 at 60Hz over LC optical cable The 610T attaches to the transmitter side of a fiber optical cable and the 610R connects to the receiver end and both are sold as a set The 610T and 610R feature A maximum data rate of 4 95Gbps 1 65Gbps per graphic channel Inputs DVI D on a DVI I connector 610T 4 LC optical connectors for R G B amp clock 610R Outputs 4 LC optical connectors for R G B amp clock 610T DVI D on a DVI connector 610R Laser standards compliance IEC 60825 1 FDA 21CFR1040 Laser Class 1 Safety of laser products No EMI RFI HDTV Compatibility No HDCP Compliance A system range of up to 400m 131 2ft EDID capture that copies and stores the EDID from a display device 610T Multi mode fiber optic cable with 4 simplex or 2 duplex LC fib
11. nders and Repeaters GROUP 6 Specialty AV Products GROUP 7 Scan Converters and Scalers GROUP 8 Cables and Connectors GROUP 9 Room Connectivity GROUP 10 Accessories and Rack Adapters GROUP 11 Sierra Video Products GROUP 12 Digital Signage GROUP 13 Audio and GROUP 14 Collaboration Congratulations on purchasing your Kramer 610T Detachable Optical DVI Transmitter and 610R Detachable Optical DVI Receiver which are ideal for the following typical applications e Digital flat panel displays plasma display panels and projectors for medical appliances aero and traffic control factory facilities banks conference rooms and auditoriums e Kiosks with digital flat panel displays for information display e LED signboards in streets and in stadiums e Digital signage The package includes e 610T Detachable Optical DVI Transmitter and 610R Detachable Optical DVI Receiver e 2 power adapters 5V DC input e This user manual Introduction 2 2 1 Getting Started We recommend that you Unpack the equipment carefully and save the original box and packaging materials for possible future shipment Review the contents of this user manual Use Kramer high performance high resolution cables Go to http www kramerelectronics com support product_downloads asp to check for up to date user manuals application programs and to check if firmware upgrades are available where appropriate Achieving the Best Perfo
12. nics office nearest you In order to pursue any remedy under this limited warranty you must possess an original dated receipt as proof of purchase from an authorized Kramer Electronics reseller If this product is returned under this limited warranty a return authorization number obtained from Kramer Electronics will be required You may also be directed to an authorized reseller or a person authorized by Kramer Electronics to repair the product Ifitis decided that this product should be returned directly to Kramer Electronics this product should be properly packed preferably in the original carton for shipping Cartons not bearing a return authorization number will be refused Limitation on Liability THE MAXIMUM LIABILITY OF KRAMER ELECTRONICS UNDER THIS LIMITED WARRANTY SHALL NOT EXCEED THE ACTUAL PURCHASE PRICE PAID FOR THE PRODUCT TO THE MAXIMUM EXTENT PERMITTED BY LAW KRAMER ELECTRONICS IS NOT RESPONSIBLE FOR DIRECT SPECIAL INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM ANY BREACH OF WARRANTY OR CONDITION OR UNDER ANY OTHER LEGAL THEORY Some countries districts or states do not allow the exclusion or limitation of relief special incidental consequential or indirect damages or the limitation of liability to specified amounts so the above limitations or exclusions may not apply to you Exclusive Remedy TO THE MAXIMUM EXTENT PERMITTED BY LAW THIS LIMITED WARRANTY AND THE REMEDIES SET FORTH ABOVE ARE EXCLUSIVE AND IN LIEU OF
13. nnector directly to the DVI connector of the computer Do not use any intermediate cable or adapter between them Connect the 610R to the 5V DC power adapter and connect the adapter to the mains electricity The Indication LED is on Connect the 610R DVI connector directly to the DVI connector of the display device Do not use any intermediate cable or adapter between them Connect the duplex LC fiber cables to the 610T and 610R modules one cable at a time as illustrated in Figure 3 Two duplex LC receptacles connected to two duplex LC patch cord multimode glass of fibers with a 62 5 125um or a 50 125um core wl a ta l pg fle M a YE m 610T Transmitter 610R Receiver Figure 3 Connecting the Fiber Optic Cables 6 Turn ON the Power on the computer and the display device 7 Ifthe transmitter does not power up connect the 5V power adapter to the 610T transmitter and connect the adapter to the mains electricity N 4 3 You can use the power supplied through a DVI pin from the graphic cards instead of using the power adapter After completing the installation if the system does not seem to work properly reconnect the power adapter while the system is powered 8 Setup the screen resolution as required LL y9802233323223209 Display Power S Power Supply Computer Supply Figure 4 Connecting the 610T 610R Deta
14. rmance To achieve the best performance Use only good quality connection cables to avoid interference deterioration in signal quality due to poor matching and elevated noise levels often associated with low quality cables Do not secure the cables in tight bundles or roll the slack into tight coils Avoid interference from neighboring electrical appliances that may adversely influence signal quality Position your Kramer 610T 610R away from moisture excessive sunlight and dust This equipment is to be used only inside a building It may only be connected to other equipment that is installed inside a building 2 2 Safety Instructions Caution There are no operator serviceable parts inside the unit Warning Use only the Kramer Electronics input power wall adapter that is provided with the unit Warning Disconnect the power and unplug the unit from the wall before installing Warning Class 1 Laser Product Invisible laser radiation present Avoid long term viewing of laser Avoid the use of magnifying viewing aids or instruments Such as binoculars telescopes microscopes and magnifying lenses but not spectacles or contact lenses Avoid placing optical devices in the emitted beam that could cause the concentration of the laser radiation to be increased 2 3 Recycling Kramer Products The Waste Electrical and Electronic Equipment WEEE Directive 2002 96 EC aims to reduce the amount of WEEE sent for disposal to landfi
Download Pdf Manuals
Related Search