FCC 47 CFR PART 15 SUBPART B TEST REPORT
Contents
1. 15 T2 IESIT INSIRUMEN TS aeree renere HP REC EE EnA EE Eaei EENEN 16 la TEST PROCEDURES rroen sonio LE EEEE 17 FE NU IMS PU nirea E en es ane E EE E 18 2 DATA SAMPLE EEEE ECE SERE pe cuem EEEE tea idee 19 20 TESTRESULIS eC M 20 8 PHOTOGRAPHS OF THE TEST 24 Page 3 This report shall not be reproduced except in full without the written approval of Compliance Certification Services C Compliance Certification Services Inc Report No T400909107 D 1 TEST RESULT CERTIFICATION Product Graphics Model eh1 VIA Applicant VIA TECHNOLOGIES INC 1F No 533 Chung Cheng Road Hsin Tien Taipei 231 Taiwan Manufacturer VIA TECHNOLOGIES INC 1F No 533 Chung Cheng Road Hsin Tien Taipei 231 Taiwan Tested September 16 21 2010 Test Voltage 100VAC 60Hz Standard Item Result Remarks FCC 47 CFR Part 15 Subpart B July 10 2008 Conducted Main Port PASS Meet Class B limit ICES 003 Issue 4 M ANSI C63 4 2003 Radiated PASS Meet Class B limit Note 1 The statements of test result on the above are decided by the request of test standard only the measurement uncertainties are not factored into this compliance determination 2 The in2. Site VSWR SIDT EUROPE 9x6x6 N A 02 26 2011 Turn Table CCS CC T 1F N A N C R Antenna Tower CCS CC A 1F N A N C R Controller CCS CC C 1F N A N C R Test S W NOTE 1 The calibration interval of the above test instruments is 12 months and the calibrations are traceable to NML ROC and NIST USA 2 N C R No Calibration Request Page 16 This report shall not be reproduced except in full without the written approval of Compliance Certification Services O Compliance Certification Services Inc Report No T100909107 D 7 3 TEST PROCEDURES please refer to measurement standard or CCS SOP PA 031 Procedure of Preliminary Test The equipment was set up as the test configuration to simulate typical usage per the manual When the EUT is a tabletop system a wooden turntable with a height of 0 8 meters is used which is placed on the ground plane When the EUT is a floor standing equipment it is placed on the ground plane which has a 3 12 mm non conductive covering to insulate the EUT from the ground plane Support equipment if needed was placed per ANSI C63 4 e All I O cables were positioned to simulate typical usage as per ANSI C63 4 e The EUT received AC power source from the outlet socket under the turntable All support equipment power received from another socket under the turntable e The antenna was placed at 3 or 10
3. 00 2 60 312 10 166 00 QP 8 616 00 33 59 0 36 33 95 37 00 3 05 91 30 120 10 QP 9 770 20 32 28 2 52 34 80 37 00 2 20 232 30 100 00 QP REMARKS The other emission levels were very low against the limit Page 20 This report shall not be reproduced except in full without the written approval of Compliance Certification Services O Compliance Certification Services Inc Report No T100909107 D dBuV m 70 0 60 0 50 0 400 la l o ES x54 l x dT IT d Di 3 31 LH MHH M HEEH 0 0 1 i i i i PO 30 50 100 200 300 400 500 600 700 800 1000 Frequency MHz No Frequency Reading Correction Result Limit Margin Degree Height Remark MHz dBuV Factor dB m dBuV m dBuV m dB cm 1 72 52 39 36 17 67 21 69 30 00 8 31 150 10 400 00 QP 2 124 20 32 75 11 15 21 60 30 00 8 40 147 20 400 00 QP 3 154 07 33 53 12 91 20 62 30 00 9 38 128 00 400 00 QP 4 184 29 36 63 13 63 23 00 30 00 7 00 331 60 400 00 QP 5 233 60 38 18 10 98 27 20 37 00 9 80 225 60 400 00 QP 6 462 16 35 14 2 94 32 20 37 00 4 80 353 90 165 80 QP 7 616 90 30 84 0 36 31 20 37 00 5 80 29 00 120 70 QP 8 770 20 32 08 2 52 34 60 37 00 2 40 239 20 100 00 QP REMARKS The other emission levels were very low against the limit Page 21 This report shall not be reproduced except in full wit
4. TEST Page 25 This report shall not be reproduced except in full without the written approval of Compliance Certification Services
5. full without the written approval of Compliance Certification Services O Compliance Certification Services Inc Report No T100909107 D 6 6 TEST RESULTS CCS Conduction Test 4 e dB Bandwidth Bandwidth Environmental 8 Tested By Juicheng Su Lie o 80 0 dBuV QP AVG 40 2 1 4 5 6 0 0 0 150 0 5 MHz 5 30 000 QuasiPeak Average Correction QuasiPeak Average QuasiPeak Average QuasiPeak Average NO Frequency Remark reading reading factor result result limit limit margin margin MHz dBuV dBuV dB dBuV dBuV dBuV dBuV dB dB Pass Fail 1 0 1510 20 40 12 56 9 65 30 05 22 21 65 94 55 94 35 89 33 73 Pass 2 0 2066 15 82 11 33 9 65 25 47 20 98 63 34 53 34 37 87 32 36 Pass 3 0 2668 22 89 19 38 9 65 32 54 29 03 61 21 51 22 28 67 22 19 Pass 4 0 4000 14 66 12 45 9 65 24 31 22 10 57 85 47 85 33 54 25 75 Pass 5 0 4688 14 40 12 76 9 58 23 98 22 34 56 53 46 54 32 55 24 20 Pass 6 2 8040 16 68 10 43 9 67 26 35 20 10 56 00 46 00 29 65 25 90 Pass REMARKS L1 Line One Live Line Page 13 This report shall not be reproduced except in full without the written approval of Compliance Certification Services O Compliance Certification Services Inc Report No T100909107 D CCS Conduction Test 4 e dB Bandwidth Bandwidth Environmental o Tested By Juicheng Su Lie O 80 0 QP AVG 40 23 4 4 5 6 0 0 0 150 0 5 MHz 5 30 000 QuasiPeak Average Correc
6. printer the printer will print pattern on paper The H pattern will be shown on the screen of monitor through the EUT Personal Computer reads and writes data into and from modem Repeat the above procedure 4 to 7 Note Test program is self repeating throughout the test Page 6 This report shall not be reproduced except in full without the written approval of Compliance Certification Services C Compliance Certification Services Inc Report No T400909107 D 4 SETUP OF EQUIPMENT UNDER TEST 4 1 DESCRIPTION OF SUPPORT UNITS The EUT has been tested as an independent unit together with other necessary accessories or support units The following support units or accessories were used to form a representative test configuration during the tests No Equipment Model No Serial No FCC ID Trade Name Data Cable Power Cord D SUB Cable LCD Monitor 2408WrFB CN OG293H 74261 DELL Shielded 1 8m Unshielded 1 8m 87C 0LVS A00 with two cores CN 0G293H 74261 HDMI Cable LCD Monitor 2408WFB pepe FCC DoC DELL gm Unshielded 1 8m DM 1414 304012264 IFAXDM1414 ACEEX Unshielded 1 8m Unshielded 1 8m PS 2Keyboard Y SJ17 SY528UK Logitech Unshielded 1 8m N A PS 2 Mouse M S34 HCA25200078 021211029 Logitech Unshielded 1 8m N A Note Grounding was established in accordance with the manufacturer s requirements and conditions for the inte
7. used in the device without going below the lowest frequency for which a radiated emission limit is specified up to the frequency shown in the following table Highest frequency generated or used in the device Upper frequency of measurement range or in which the device operated or tunes MHz MHz Below 1 75 30 1 75 108 1000 108 500 2000 500 1000 5000 in 7 F Above 1000 5 harmonic of 9 or 40GHz Page 15 This report shall not be reproduced except in full without the written approval of Compliance Certification Services Report No T100909107 D O Compliance Certification Services Inc 7 2 TEST INSTRUMENTS Open Area Test Site 1 Manufacturer Model Serial Number ADVANTEST R3261C 81720301 ESVS20 838804 004 03 28 2011 8447D 2944A09173 04 13 2011 C Calibration Due N C R Name of Equipment Spectrum Analyzer EMI Test Receiver Pre Amplifier Bilog Antenna amp S P 3 Meter Chamber Model E4446A 8449B AMF 6F 260400 40 8P 3115 3116 104PEA 104PEA Calibration Due 11 05 2010 04 17 2011 05 23 2011 05 09 2011 10 13 2010 08 13 2011 04 17 2011 Serial Number MY48250064 3008A00965 985646 9602 4659 00026370 24815 4PEA 30956 4PEA Name of Equipment Manufacturer Spectrum Analyzer Agilent Pre Amplifier HP MITEQ EMCO EMCO Huber Suhner Huber Suhner Pre Amplifier Horn Antenna Horn Antenna Low Loss Cable Low Loss Cable
8. 74 45 46 54 39 54 00 74 00 8 54 19 61 Frequency MHz Emission frequency in MHz Reading dBuV Uncorrected Analyzer Receiver reading Correction Factor dB m Antenna factor Cable loss Amplifier gain Result dBuV m Reading dBuV Corr Factor dB m Limit dBuV m Limit stated in standard Margin dB Result dBuV m Limit dBuV m Q P Quasi Peak Page 19 This report shall not be reproduced except in full without the written approval of Compliance Certification Services C Compliance Certification Services Inc Report No T400909107 D 7 6 TEST RESULTS Below 1GHz Antenna Pole Vertical Antenna Distance 10m dBuV m 70 0 60 0 50 0 S 300 m Erer 551 341 41 LT IL pL Jd IJ 0 0 1 i i i i i i P 30 50 100 200 300 400 500 600 700 800 1000 Frequency MHz No Frequency Reading Correction Result Limit Margin Degree Height Remark MHz dBuV Factor dB m dBuV m dBuV m dB cm 1 64 24 42 42 18 42 24 00 30 00 6 00 0 00 100 00 QP 2 74 08 44 61 17 41 27 20 30 00 2 80 79 40 100 00 QP 3 117 28 37 69 11 29 26 40 30 00 3 60 66 00 100 00 QP 4 153 96 40 15 12 90 27 25 30 00 2 75 348 80 100 00 QP 5 185 86 36 56 13 56 23 00 30 00 7 00 353 50 100 00 QP 6 233 80 40 75 10 95 29 80 37 00 7 20 0 00 400 00 QP 7 462 20 37 34 2 94 34 40 37
9. FCC 47 PART 15 SUBPART TEST REPORT for Graphics Card MODEL eh1 Test Report Number T100909107 D Issued for VIA TECHNOLOGIES INC 1F No 533 Chung Cheng Road Hsin Tien Taipei 231 Taiwan Issued By Compliance Certification Services Inc Linkuo Laboratory No 81 1 Lane 210 Pa De 2nd Rd Luchu Hsiang Taoyuan Shien 338 Taiwan TEL 886 3 324 0332 FAX 886 3 324 5235 E Mail service ccsrf com Issued Date September 27 2010 ewe L77 SOY 2 j ICMA TAF 9 ACCREDITED Gj MN Testing Laboratory TESTING CERT 0824 01 ila 0363 Note This report shall not be reproduced except in full without the written approval of Compliance Certification Services Inc This document may be altered or revised by Compliance Certification Services Inc personnel only and shall be noted in the revision section of the document The client should not use it to claim product endorsement by TAF A2LA NIST or any government agencies The test results in the report only apply to the tested sample Page 1 25 O Compliance Certification Services Inc Report No T100909107 D Revision History Revised By 00 September 27 2010 Initial Issue Celine Chou Page 2 This report shall not be reproduced except in full without the written approval of Compliance Certification Services O Compliance Certification Services Inc Report No T100909107 D TABLE OF CONTENTS 1 TEST RES
10. On Board PORT PORT TYPES Q TY TESTED WITH 1 DVI Port 1 2 HDMI Port 1 1 Page 5 This report shall not be reproduced except in full without the written approval of Compliance Certification Services C Compliance Certification Services Inc Report No T400909107 D 3 TEST METHODOLOGY 3 1 DECISION OF FINAL TEST MODE 1 The following test mode s were scanned during the preliminary test Pre Test Mode Mode 1 DVI 1920 x 1200 Resolution 60Hz Mode 2 HDMI 1920 x 1200 Resolution 60Hz Mode 3 DVI 1920 x 1200 Resolution 60Hz 1920 x 1200 Resolution 60Hz Mode 4 DVI 1440 x 900 Resolution 60Hz 1920 x 1200 Resolution 60Hz Mode 5 DVI 1024 x 768 Resolution 60Hz 1920 x 1200 Resolution 60Hz Mode 6 DVI 800 x 600 Resolution 60Hz 1920 x 1200 Resolution 60Hz 2 After the preliminary scan the following test mode was found to produce the highest emission level Final Test Mode Conducted p Mode 3 M Emission Emission SE Mode 3 Emission Then the above highest emission mode of the configuration of the EUT and cable was chosen for all final test items 3 2 EUT SYSTEM OPERATION 1 Install EUT into the Personal Computer and simulators as shown on 4 2 on the power of all equipment Personal Computer reads data from disk 2 3 4 EMC Test Run test program and run H pattern Personal Computer sends H pattern to
11. ULT CERTIFICATION 2 4 2 5 3 TEST aca ae 6 3 1 DECISION OF FINAL TEST MODE n oerte rines renonce 6 3 2 EUT SYSTEM OPERATION rax e ru eee ieee eee 6 4 SETUP OF EQUIPMENT UNDER 7 4 1 DESCRIPTION OF SUPPORT UNTTS eaten etico oie eot erences 7 4 2 CONFIGURATION OF SYSTEM UNDER 7 5 FACILITIES AND ACCREDITATIONS 8 m FAGLEG MEC EE 8 MEE CP EE Ss 8 53 MEASUREMENT UNCERTAING Y ite EUH 9 6 CONDUCTED EMISSION MEASUREMENT 10 6 1 LIMITS OF CONDUCTED EMISSION 50 10 6 2 TEST INSTRUMENTS odd acum Pine sup PEL Uo qup FU DdUE 10 ps TEST PROCEDURES 11 ST PEN TINI DU ar ee ae 12 6 5 DATA SAMPL E 12 6 6 13 7 RADIATED EMISSION 15 7 1 LIMITS OF RADIATED EMISSION 5
12. ces Inc Report No T100909107 D 5 3 MEASUREMENT UNCERTAINTY Where relevant the following measurement uncertainty levels have been estimated for tests performed on the EUT as specified in CISPR 16 4 2 Conducted emissions 9kHz 30MHz 2 0518 2 30 200MHz 13 8856 Radiated emissions 200 1000MHz 3 8721 This uncertainty represents an expanded uncertainty expressed at approximately the 9596 confidence level using a coverage factor of k 2 Consistent with industry standard e g CISPR 22 2006 clause 11 Measurement Uncertainty determining compliance with the limits shall be base on the results of the compliance measurement Consequently the measure emissions being less than the maximum allowed emission result in this be a compliant test or passing test The acceptable measurement uncertainty value without requiring revision of the compliance statement is base on conducted and radiated emissions being less than Ucispr which is 3 6dB and 5 2dB respectively CCS values called 2 in CISPR 16 4 2 is less than Uc seg as shown in the table above Therefore MU need not be considered for compliance Page 9 This report shall not be reproduced except in full without the written approval of Compliance Certification Services O Compliance Certification Services Inc Report No T100909107 D 6 CONDUCTED EMISSION MEASUREMENT 6 1 LIMITS OF CONDUCTED EMISSION MEASUREMENT Class A dBuV Class B dBuV FREQUENCY MHz 1 The l
13. equipment it is placed on the ground plane which has a 12 mm non conductive covering to insulate the EUT from the ground plane e All I O cables were positioned to simulate typical actual usage as per ANSI C63 4 e The test equipment EUT installed by AC main power through a Line Impedance Stabilization Network LISN which was supplied power source and was grounded to the ground plane e All support equipment power by from a second e The test program of the EUT was started Emissions were measured on each current carrying line of the EUT using an EMI Test Receiver connected to the LISN powering the EUT e The Receiver scanned from 150kHz to 30MHz for emissions in each of the test modes e During the above scans the emissions were maximized by cable manipulation e Thetest mode s described in Item 3 1 were scanned during the preliminary test e After the preliminary scan we found the test mode described in Item 3 1 producing the highest emission level e The worst configuration of EUT and cable of the above highest emission level were recorded for reference of the final test Procedure of Final Test EUT and support equipment were set up on the test bench as per the configuration with highest emission level in the preliminary test e Ascan was taken on both power lines Line 1 and Line 2 recording at least the six highest emissions Emission frequency and amplitude were recorded into a computer in which correction
14. ere used to calculate the emission level and compare reading to the applicable limit and only Q P reading is presented e The test data of the worst case condition s was recorded Page 17 This report shall not be reproduced except in full without the written approval of Compliance Certification Services O Compliance Certification Services Inc Report No T100909107 D 7 4 TEST SETUP Below 1GHz Test table amp Turntable 1 or 1m 4m Boundary of Coaxial Cable Ground Plane EMI Receiver Above 1GHz Antenna 7 tower gt 3m pepe Horn V antenna EUT 4 4m p oU Spectrum L x analyzer Turntable e For the actual test configuration please refer to the related item Photographs of the Test Configuration Page 18 This report shall not be reproduced except in full without the written approval of Compliance Certification Services O Compliance Certification Services Inc Report No T100909107 D 7 5 DATA SAMPLE Below 1GHz Frequency Reading m Result Limit Margin Degree Height MHz dBuV dB m dBuV m dBuV m dB xx 1649 ose 3000 65 neo 10100 GP Above 1GHz Corr Reading Result Limit Margin Frequency Factor MHz dB m Average Peak Average Peak Average Peak Average Peak dBuV m dBuV m dBuV m dBuV m dBuV m dBuV m dB dB XXXX XXX 4 35 49 81 58
15. factors were used to calculate the emission level and compare reading to the applicable limit e The test data of the worst case condition s was recorded Page 11 This report shall not be reproduced except in full without the written approval of Compliance Certification Services O Compliance Certification Services Inc Report No T100909107 D 6 4 TEST SETUP Vert reference plane 2 O EUT A O g 80cm s LISN S Reference ground plane O 40cm e For the actual test configuration please refer to the related item Photographs of the Test Configuration 6 5 DATA SAMPLE F QuasiPeak Average Correctrion QuasiPeak Average QuasiPeak Average QuasiPeak Average requency d 5 MHz reading reading factor result result limit limit margin margin dBuV dBuV dB dBuV dBuV dBuV dBuV dB dB X XX 43 95 33 00 10 00 53 95 43 00 56 00 46 00 Pass Frequency MHz Emission frequency in MHz Reading dBuV Uncorrected Analyzer Receiver reading Insertion loss of LISN if it gt 0 5 dB Correction Factor dB LISN Factor Cable Loss Result dBuV Raw reading converted to dBuV and CF added Limit dBuV Limit stated in standard Margin dB Result dBuV Limit dBuV Page 12 This report shall not be reproduced except in
16. formation of measurement uncertainty is available upon the customer s request Deviation from Applicable Standard None The above equipment has been tested by Compliance Certification Services Inc and found compliance with the requirements set forth in the technical standards mentioned above The results of testing in this report apply only to the product system which was tested Other similar equipment will not necessarily produce the same results due to production tolerance and measurement uncertainties Approved by Reviewed by a 3 N Ethan Huang Stan Lin Section Manager Supervisor Page 4 This report shall not be reproduced except in full without the written approval of Compliance Certification Services C Compliance Certification Services Inc Report No T400909107 D 2 EUT DESCRIPTION Product Brand Name Model Applicant Serial Number Received Date EUT Power Rating PC Configuration Power Supply Power Rating Graphics Card VIA TECHNOLOGIES INC T100909107 September 9 2010 Powered by PC Power Supply Manufacturer Sea Soine Model SS 500HT Active PFC F3 I P 100 240VAC 50 60Hz 9A O P 3 3VDC 30A 5VDC 30A 12V1 17A 12V2 16A 12V 0 8A 5Vsb 2A Memory Capacity 3GB CPU Manufacturer VIA Model 1 60GHz HDD Manufacturer Samsung Model SP1213C 111GB LAN Card Manufacturer On Board VGA Card Manufacturer On Board Sound Card Manufacturer
17. hout the written approval of Compliance Certification Services C Compliance Certification Services Inc Above 1GHz Antenna Pole Test Mode Environmental 60 RH Bandwidth 4 MHz Conditions Report No T100909107 D Detector Function Tested By Han Chaic Frequency Corr Reading Result Limit Margin Degree Height Factor Average Peak Peak Average Peak Average Peak MHz j dBuV m dBuV m dBuV m dBuV m dBuV m dBuV m dBuV m dB dB cm 1640 000 5 89 51 92 46 03 74 00 27 97 244 100 2110 000 3 27 49 23 45 96 74 00 28 04 178 100 2240 000 2 83 49 04 46 21 74 00 27 79 360 100 2590 000 1 49 48 93 47 44 74 00 26 56 256 100 3060 000 0 64 47 01 47 65 74 00 26 35 133 100 3530 000 2 22 45 49 47 71 74 00 26 29 224 100 REMARKS 1 The other emission levels were very low against the limit 2 means the average measurement was not performed when the measured peak data under the limit of average detection Page 22 This report shall not be reproduced except in full without the written approval of Compliance Certification Services O Compliance Certification Services Inc Antenna Pole ent TestMode Mode FAME el E 609 RH Bandwidth MHz Conditions Re
18. meter away from the EUT as stated in ANSI C63 4 The antenna connected to the Spectrum Analyzer via a cable and at times a pre amplifier would be used e The Analyzer Receiver quickly scanned from 30MHz to 40GHz The EUT test program was started Emissions were scanned and measured rotating the EUT to 360 degrees and positioning the antenna 1 to 4 meters above the ground plane in both the vertical and the horizontal polarization to maximize the emission reading level e Thetest mode s described in Item 3 1 were scanned during the preliminary test e After the preliminary scan we found the test mode described in Item 3 1 producing the highest emission level e The worst configuration of EUT and cable of the above highest emission level were recorded for reference of the final test Procedure of Final Test e EUT and support equipment were set up on the turntable as per the configuration with highest emission level in the preliminary test e The Analyzer Receiver scanned from 30MHz to 40GHz Emissions were scanned and measured rotating the EUT to 360 degrees varying cable placement and positioning the antenna 1 or 1 to 4 meters above the ground plane in both the vertical and the horizontal polarization to maximize the emission reading level e Recording at least the six highest emissions Emission frequency amplitude antenna position polarization and turntable position were recorded into a computer in which correction factors w
19. nded use 4 2 CONFIGURATION OF SYSTEM UNDER TEST 1 LCD Monitor 2 LCD Monitor 3 Modem 4 PS 2 Keyboard 5 PS 2 Mouse Test table Page 7 This report shall not be reproduced except in full without the written approval of Compliance Certification Services C Compliance Certification Services Inc Report No T400909107 D 5 FACILITIES AND ACCREDITATIONS 5 1 FACILITIES All measurement facilities used to collect the measurement data are located at No 81 1 Lane 210 Pa De 2nd Rd Luchu Hsiang Taoyuan Shien Taiwan The sites are constructed in conformance with the requirements of ANSI C63 4 and CISPR 22 All receiving equipment conforms to CISPR 16 1 1 CISPR 16 1 2 CISPR 16 1 3 CISPR 16 1 4 CISPR 16 1 5 and CISPR 16 2 3 5 2 ACCREDITATIONS Our laboratories are accredited and approved by the following approval agencies according to ISO IEC 17025 Taiwan TAF USA A2LA The measuring facility of laboratories has been authorized or registered by the following approval agencies Canada Industry Canada Norway Nemko Japan VCCI Taiwan BSMI USA FCC Copies of granted accreditation certificates are available for downloading from our web site http www ccsrf com Page 8 This report shall not be reproduced except in full without the written approval of Compliance Certification Services O Compliance Certification Servi
20. ower limit shall apply at the transition frequencies 2 The limit decreases in line with the logarithm of the frequency in the range 0 15 to 0 50 MHz 3 All emanations from a class A B digital device or system including any network of conductors and apparatus connected thereto shall not exceed the level of field strengths specified above 6 2 TEST INSTRUMENTS Conducted Emission Room 4 Name of Equipment Manufacturer Serial Number Calibration Due EMI Test Receiver ESCI 100782 06 10 2011 LISN ENV216 100066 03 31 2011 LISN ENV 4200 830326 016 04 27 2011 Test S W EZ EMC NOTE 1 The calibration interval of the above test instruments is 12 months and the calibrations are traceable to NML ROC and NIST USA 2 N C R No Calibration Request Page 10 This report shall not be reproduced except in full without the written approval of Compliance Certification Services O Compliance Certification Services Inc Report No T100909107 D 6 3 TEST PROCEDURES please refer to measurement standard or CCS SOP PA 031 Procedure of Preliminary Test e The EUT and support equipment if needed were set up as per the test configuration to simulate typical usage per the user s manual When the EUT is a tabletop system a wooden table with a height of 0 8 meters is used and is placed on the ground plane as per ANSI C63 4 see Test Facility for the dimensions of the ground plane used When the EUT is a floor standing
21. port No T100909107 D Detector Function Tested By Han Chaic Frequency Corr Reading Result Limit Margin Degree Height Factor Average Peak Peak Peak Peak MHz j dBuV m dBuV m dBuV m dBuV m dBuV m dBuV m dBuV m dB dB cm 1360 000 7 56 51 57 44 01 74 00 29 99 322 100 1470 000 6 92 49 75 42 83 74 00 31 17 199 100 1582 001 6 24 48 91 42 67 74 00 31 33 178 100 1920 000 4 15 49 72 45 57 74 00 28 43 334 100 2150 000 3 13 47 42 44 29 74 00 29 71 166 100 2820 000 0 40 47 04 46 64 74 00 27 36 244 100 REMARKS 1 The other emission levels were very low against the limit 2 means the average measurement was not performed when the measured peak data under the limit of average detection Page 23 This report shall not be reproduced except in full without the written approval of Compliance Certification Services O Compliance Certification Services Inc Report No T100909107 D 3 PHOTOGRAPHS OF THE TEST CONFIGURATION CONDUCTED EMISSION TEST Page 24 This report shall not be reproduced except in full without the written approval of Compliance Certification Services O Compliance Certification Services Inc Report No T100909107 D RADIATED EMISSION
22. tion QuasiPeak Average QuasiPeak Average QuasiPeak Average NO Frequency Remark reading reading factor result result limit limit margin margin MHz dBuV dBuV dB dBuV dBuV dBuV dBuV dB dB Pass Fail 1 0 1509 20 92 13 38 9 66 30 58 23 04 65 94 55 95 35 36 32 91 Pass 2 0 1748 15 53 10 81 9 66 25 19 20 47 64 72 54 73 39 53 34 26 Pass 3 0 2017 20 85 13 91 9 66 30 51 23 57 63 54 53 54 33 03 29 97 Pass 4 0 2686 21 06 18 67 9 66 30 72 28 33 61 16 51 16 30 44 22 83 Pass 5 0 4013 18 19 16 12 9 66 27 85 25 78 57 83 47 83 29 98 22 05 Pass 6 2 8040 16 41 11 15 9 69 26 10 20 84 56 00 46 00 29 90 25 16 Pass REMARKS L2 Line Two Neutral Line Page 14 This report shall not be reproduced except in full without the written approval of Compliance Certification Services O Compliance Certification Services Inc Report No T100909107 D 7 RADIATED EMISSION MEASUREMENT 7 1 LIMITS OF RADIATED EMISSION MEASUREMENT FREQUENCY MHz dBuV m At 10m Class A Class B 30 230 40 30 230 1000 47 37 Frequency Class A dBuV m At 3m Class B dBuV m At 3m mHz average Peak Average Pea NOTE 1 The lower limit shall apply at the transition frequencies 2 Emission level dBuV m 20 log Emission level uV m According to FCC Part 15 33 b for an unintentional radiator including a digital device the spectrum shall be investigated from the lowest radio frequency signal generated or
Download Pdf Manuals
Related Search