LED NEUTRON II Centre-piece Light Effect
Contents
1. Ensure adequate air flow to the housing for cooling Ensure adequate access to controls and connections Cleaning Use a soft dry or slightly damp to clean the cabinet and lenses Do not use solvents Connections and controls O O MIC NOOL SUVE O Q DMX MASTER SOUND DMKIN DM OUT 6 008 o 1 2 3 4 5 6 7 8 i Safety cable eyebolt 5 DMX in 3 pin XLR 2 LED display 6 DMX out 3 pin XLR 3 Control panel buttons 7 Mains inlet IEC amp fuse holder d Internal microphone 8 Mains daisy chain output IEC 151 579UK User Manual E qtx Setting up Install the LED NEUTRON II using the mounting bracket ideally to a secure point on a ceiling or trussing Experiment with positioning and distance to get the best coverage for the area to be lighted For DMX or master slave control link DMX out 6 to DMX in 5 using good quality DMX leads Connect the LED NEUTRON II to the mains supply using the appropriate IEC lead 7 A female IEC output can be used to daisy chain mains connection to other fixtures 8 Control panel settings The LED Neutron II can be operated in sound activated DMX and master slave modes Depending upon which mode of operation is required it will be necessary to select options and settings via the control panel 3 and display 2 To set the operating mode press MENU then UPA or DOWN v through options then ENTER to select an option To exit the menu press MENU and hold for 22. in the menu 5Eb4Y offers a choice of sound activation when no DMX signal is present There are 2 modes of DMX which are selected via the Chnd option on the control panel The channel allocations for DMX operation are detailed below 151 579UK User Manual E qtx Mode Value T Function _ _ _ _ Blackout No LED output o Blackout 000 015 No LED output Channel 1 016 239 Pre programmed sequence slow to fast 240 255 Sound activated operation B 000 000 Channel 2 10mm LEDs 001 255 Strobe slow to fast 7CH Mode Mode Value 1 Function 000 000 Blackout 001 199 Dimmer 0 100 S Channel 1 10mm LEDs 001 199 Dimmer 0 100 Channel Rea 000 255 Red brightness 0 100 O ga Channel 6 Mirror rotation Channel 7 Sound 000 127 Sound activation off 128 255 Sound activation on Specifications 100 240Vac 50 60Hz IEC in out 60W F3A 4 x 10W quad CREE LED 72 x 10mm white LED 350 x 335 x 170mm 7 or 2 channels 4 3kg BSEN60825 1 2007 Troubleshooting Check mains voltage is correct and outlet is switched on isla No LED display Nadentoutslt No strobe output ide Aca hcl Check that DMX mode is enabled set Addr on control panel Overheating Ensure that the unit is not too close to a heat source cutting out Ensure that adequate airflow is afforded for cooling Electronic equipment and should not be disposed with other household or commercial waste at the end of its useful
3. seconds Display Mode press ENTER for setting Z O Z o o Strobe mode on oFF strobe LEDs on or off sound activated when no DMX signal is present p Microphone sensitivity 0 100 0 100 gain S LED display dimmer oFF display off after 20s on constant display Sound activation Soll slow during silence 50u off during silence LED display inverted di SP dS P normal or inverted display EESE Fixture test sequence Fixture steps through all functions press MENU to exit Displays how many hours of use for the fixture Standalone and Master Slave operation Standby mode DMX fixture is off when no DMX signal is present The LED Neutron II can operate with sound activation by navigating to Son in the menu options and selecting from Sol or SoUe as described above For this to take effect the Slave mode SLnd must be set to Master ASE and standby SEbY set to off To control further LED Neutron II fixtures from this master unit connect an XLR lead from the DMX out of the master unit to the DMX in of the slave unit and set the slave unit to one of the two Slave modes 5L I 5L 2 whichever effect is preferred DMX operation The LED Neutron II can operate from a DMX signal connected to the DMX in connector This signal can be connected on to further units from the DMX OUT connector To operate via DMX set the DMX start address in the Addr option on the control panel The standby option
4. E qtx LED NEUTRON II Item ref 151 579UK Centre piece Light Effect User Manual www avsl qtx com sn ens group brand E qtx T Caution Please read this manual carefully before operating Damage caused by misuse is not covered by the warranty Introduction Thank you for choosing the LED Neutron II centre piece light as part of your effect lighting setup This unit has been designed to provide wide angle dynamic beam effects for dance floors and live shows Please read the following instructions for best results Unpacking Your LED Neutron II should reach you in good condition supplied with appropriate mains leads and mounting bracket If there is any damage or items missing from the packaging contact your dealer immediately Warning To prevent risk of fire or electric shock do not expose any components to rain or moisture If liquids are spilled on the housing disconnect mains allow unit to dry out and have the unit checked by qualified personnel before further use No user serviceable parts inside do not open refer all servicing to qualified personnel Safety Check for correct voltage and condition of IEC lead before connecting to power outlet Ensure DMX leads are in good condition with no short connections or damaged plugs Placement e The LED Neutron II is fitted with 4 feet for handling purposes to protect the mirrors If mounted at height use the integral bracket and attach a drop cable for safety
5. life C lt X Disposal The Crossed Wheelie Bin symbol on the product means that the product is classed as Electrical or E The goods must be disposed of according to your local council guidelines Errors and omissions excepted Copyright 2013 AVSL Goup Ltd 151 579UK User Manual
Download Pdf Manuals
Related Search