HRW-4 label rewinder user`s manual
Contents
1. agent or reseller is authorised to give any warranties on behalf of TSC Any obligation to warranty other than that specifically addressed above is hereby disclaimed TSC Auto ID Technology EMEA GmbH Georg Wimmer Ring 8b 85604 Zorneding Germany TEL 49 0 8106 37979 00 FAX 49 0 8106 37979 05 emea_sales tscprinters com www tscprinters com DE TSC User_ HRW CE 01 15 Original user manual TSC HRW 4 HRW 6 CHUCK Heavy Duty HRW Label Rewinder e Dual Torque Range and Direction Controls e Constant Adjustable Torque HRW technology e Adjustable Speed Control up to 125cm per second e Precise Variable Torque HRW 4 Control picture with Adjustable Paper Guide HRW 6 CHUCK Remove all parts from the shipping container and verify contents PACKAGE CONTENTS e User Manual this document e HRW 4 HRW 6 CHUCK Drive Unit e Power Supply Module e TSC Quick Chuck Quick Locking Core Chuck or Standard Shaft with three 3 metal Vanes installed or Model 10 INCHES Shaft with six 6 metal Vanes installed or Model ACH Adjustable Core Holder Retain the Shipping Container and Packaging for Storage and Transport SPECIFICATIONS Weight of the machine 9 6Kg to 11 1Kg depending on model Max Label Roll Weight HRW 4 7Kg HRW 6 CHUCK 8Kg Max Label Roll Diam 300mm for HRW 6 CHUCK 280mm for HRW 4 Start Stop ON OFF ON Direction Switch Power Supply Input 280VAC 50Hz Outp2. MAINTENANCE Your HRW 4 HRW 6 CHUCK requires no maintenance Product Limited Warranty All TSC Products are warranted to the original end user customer to be free from defects in materials and workmanship If it is determined by TSC that a product has failed under the terms of this warranty the product will be repaired or replaced at no charge to the customer TSC reserves all rights to determination of coverage and liability under this warranty The warranty period for all new TSC products is outlined below Warranty Period Products Covered 5 years Label Rewinders Power Supply Modules The warranty period for all products starts on the date purchased by the original end user customer Warranty coverage is not transferable with ownership and will terminate immediately upon rental resale or any other change in ownership This warranty does not cover repair to any product which is damaged has been modified is missing parts or has been opened or repaired by any unauthorised person Use of any unauthorised accessory or attachment will void coverage Purchase documentation should be retained for coverage verification In the event your product requires service please contact the distributor you bought the product from The customer assumes responsibility for all cost and risk incurred in transport for service TSC makes no other warranty of any kind expressed or implied or to suitability or fitness for a particular purpose No other person
3. on desired to run left or right 8 Start the printer and adjust the TORQUE Control Knob for the desired take up tension Use the minimum TORQUE setting needed to rewind labels properly Excessive torque might pull the labels too hard and cause the printer to lose registration EXTERNAL HALT CONTROL An External Halt Control jack on the HRW is for use with external devices capable of providing an open circuit halt command A 3 5mm control cable is necessary for use not included With Pin 2 and Pin 3 of the External Halt Control circuit closed connected together using a 3 5mm dual circuit plug the HRW will operate When the External Circuit is opened the HRW will stop 3 5mm EXTERNAL HALT CONTROL Stereo Plug Dual Circuit Plug Contact CLOSED RUN Contact OPEN HALT Pin 1 No connection NOT USED Pin 2 Normally Closed NC contact ve Pin 3 Normally Closed NC contact return woo O _ g RESET 555
4. ut 11V AC 2 5A e KEEP MANUAL IN A SAFE PLACE FOR FUTURE REFERENCE e A WARNING This Product is for indoor use only Not for use in wet locations IMPORTANT INFORMATION This product is a label rewinder It is only to be used to rewind or unwind labels of the recommended dimensions and weight in an indoor dry environment The machine has to be unplugged before any manipulation The machine is to be used on a flat surface if the surface is not flat it is to be fixed using the holes in the base plate e Do not leave the power cable in a passageway e The ambient light of the working area needs to be sufficient to avoid any risk e The rewinder can be used in ambient temperatures of 2 C to 40 C e Connection of the machine to the power source must respect local and European legislations SET UP if you have the HRW 4 Adjustable Core Holder option Skip to step 3 1 CHUCK Mount the inner Flange onto the Quick Chuck with two screws provided 2 Slide the Shaft and Flange Assembly onto the HRW Motor Shaft allowing for clearance to the HRW Chassis and Motor Screws Tighten the Allen Screw onto the flat part of the Motor Shaft until it is tight 3 HRW 4 Slide the Hub of the HRW 4 over the motor Shaft of the HRW Position the Hub so there is a gap between the HRW 4 Hub and the Rewinder Drive Unit case Tighten the Allen Screw onto the flat part of the Motor Shaft until it is tight 4 Set the HRW in place near the label e
5. xit slot of the printer 5 CAUTION AVOID ACCIDENTS THE HRW WEIGHS OVER 7KG SO CHOOSE ONLY A STURDY SURFACE ON WHICH TO SET THE UNIT 6 Verify that the DIRECTION Switch on the HRW Control Panel is in the OFF position Plug the Power Plug at the end of the wire on the AC Wall Transformer into the HRW Power Input Jack Plug the AC Transformer into an appropriate AC power outlet The unit is now ready for use A FOR YOUR SAFETY Switch off device before any manipulation REWINDING LABELS 1 Place the DIRECTION Switch on the HRW Control Panel in the centre OFF position 2 Slide an empty label core over the Quick Chuck or Vanes on the shaft until the core is against the inner Flange Plate On the Quick Chuck tighten the Lock Knob for an HRW 4 see the HRW 4 user manual 3 If desired slide the outer label Flange Plate with Ball Plunger in the Hub onto the Shaft and up against the label core 4 Feed the label web from the printer and secure it to the take up roll core with tape Rotate the take up reel a couple of turns 5 Place the HRW TORQUE RANGE Switch in the NORMAL REWIND position NOTE When the TORQUE RANGE Switch is in the HIGH SLIT position the HRW develops higher torque Use the HIGH SLIT position for label slitting or rewinding large diameter rolls 6 Rotate the TORQUE Control Knob to the minimum position fully counter clockwise 7 Place the HRW DIRECTION Switch in the positi
Download Pdf Manuals
Related Search