LPTT1202 – 12-CHANNEL TOUCH PANEL CONTROLLER
Contents
1. LPT1T1202 12 CHANNEL TOUCH PANEL CONTROLLER tinvowuction CE EE Lite Puter Thank you for buying the LPTT1202 Please read the manual carefully before bringing this device into service This device features 12 channels 24 touch sensors flash and hold modes two colour LED indicators 3 synchronous chase controls chase speed control and 6 signal output connectors one 25 pin SUB D connector amp five 8 pin DIN connectors Make sure that the device was not damaged in transit If the device is damaged you should contact your dealer and postpone installation of this device MMi 2 Safety Instructions Be very careful when installing the device touching live wires can cause life threatening electroshocks AN Do not touch the device during operation as the housing heats up Protect this device against rain and moisture Unplug the supply cable before you open the housing e a qualified technician should install and service this device e damages caused by disregarding certain guidelines in this manual are not covered by the warranty and the dealer will not accept responsibility for the ensuing defects or problems e do not switch the device on immediately if it has been exposed to changes in temperature Protect the device against damage by leaving it switched off until it has reached room temperature this device falls under protection class I It is essential therefore that the device be earthed Have this de2. SIGNAL OUT 1 x 12 CHs 25 pin SUB D connector for connection to a power pack The LPTP406 is a 4 channel patchable power pack 10A channel CONNECTIONS see also figure above LPTT1202 LPTT1202 LPTP406 RT LPTP406 LPTP406 pa LPTP406 6 Cleaning and Maintenance _ All screws should be tightened and free of corrosion 2 The housing mounting supports and connections should not be modified or tampered with e g do not drill extra holes in mounting supports do not change the location of the connections 3 The electric power supply cables should be undamaged Have this device installed by a qualified technician 7 Caution e Disconnect the device from the mains prior to maintenance e Use a moist cloth to clean the device and avoid the use of alcohol or solvents for cleaning purposes e Replace a blown fuse with an identical one e Spare parts should be ordered with your local dealer 8 Technical Specifications Power Supply 20Vdc through power pack Number of Channels 12 Signal Output ON DC 10V OFF DC 0V Dimensions 482 x 75 5 x 88mm Weight 1 3kg The information in this manual is subject to change without prior notice LPTT1202 3 GB
3. ofessional use of the device Use the original packaging if the device is to be transported Note that all modifications of the device are forbidden for safety reasons Do not remove the serial number sticker from the device as doing so will void the warranty Only use the device for its intended purpose All other uses may lead to short circuits burns electroshocks lamp explosion crash etc Using the device in an unauthorised way will void the warranty Front Panel Description HN A HN TL ATT a eA as 1 23 45 6 7 8 9 SENS touch sensitivity adjustment POWER SWITCH turns the device ON OFF POWER INDICATOR this red indicator lights when the device is activated FLASH TOUCH KEY activates the channel in question when touched HOLD TOUCH KEY the channel in question is activated when the key is touched and is deactivated when the key is released OUTPUT INDICATOR indicates if the channel is active red LED CHASE 3 buttons to select CH1 4 CH5 8 CH9 12 respectively CHASE INDICATOR indicates whether the group of 4 channels is selected as an output in the current chase red LED CHASE SPEED turn the rotary knob to adjust the chaser speed Back Panel Description LPTT1202 2 GB 10 EXT POWER for operation test only 11 SIGNAL OUT 2 x 6 CHs 8 pin DIN sockets for connection to a LPTP406 12 SIGNAL OUT 3 x 4 CHs 8 pin DIN sockets for connection to LPTP406 13
4. vice installed by a qualified technician e make sure that the available voltage does not exceed the voltage stated in the specifications of this manual e do not crimp the power cord and protect it against damage from sharp edges Ask an authorised dealer to replace the cord if necessary e always disconnect the device from the mains when it is not in use or when you wish to clean it Only handle the power cord by the plug Never pull out the plug by tugging the power cord e Do not look directly into the light source as sensitive people may go into epileptic seizure if they do e Be aware that damages caused by user modifications to the device are not covered by the warranty Keep the device away from children and unauthorised users LPTT1202 1 GB ORWN CON OD 9 5 General Guidelines This device is a light controller for professional use on stages in discos theatres etc This device should only be operated with an alternating current of max 230Vac 50Hz and is designed for indoor use only Do not shake the device Avoid brute force when installing or operating the device Select a location where the device will be protected against extreme heat moisture and dust Do not use or transport the device under temperatures lt 5 C or gt 35 C Familiarise yourself with the functions of the device before actually using it Do not permit operation by unqualified people Any damage that may occur will probably be due to unpr
Download Pdf Manuals
Related Search