English - tekcomm.tv or
Contents
1. This user manual provides complete instructions for installing and using this receiver The symbols serve as follows Warning Indicates warning information Tips Indicates any other additional important or helpful information MENU Represents a button on the remote control or the receiver Bold characters Move to Represents a menu item within a window Italic characters 1 4 Accessories m Installation Instructions 1 remote control unit m 2x batteries AAA type WARNING The batteries should not be recharged disassembled electrically short circuited be mixed or used with other types of batteries If rechargeable accumulators instead of batteries are going to be used e g NiMH we recommend using types with low self discharge to ensure long time operation of your remote control 1 5 Usage of external USB devices 15 recommended to use USB 2 0 storage devices or higher If your device is not compatible to USB 2 0 specifications recording playback and other multimedia functions of the receiver might not work properly m ensure best performance of your USB storage device please format it via your receiver through the menu Media to FAT32 system Other file systems are not supported by the receiver However it is possible to use already NTFS formatted disks TEKCOMM cannot guarantee compatibility with all types of USB storage devices m Ifyou are going to use external USB HDDs Hard Disk Drives please consi2. 6 6 6 Timeshift 10 2 6 Using the remote control 6 6 7 EPG Electronic Programme 3 0 CONNECTIONS 6 Guide 10 3 1 Connecting to a terrestrial 6 8 Instant Recording 11 antenna 6 7 0 MAIN MENU 11 3 2 Connecting to TV with HDMI 7 1 Edit Channel 11 cable 7 7 2 Installation 13 3 3 Connecting to TV with SCART 7 3 System Setup 14 cable 7 7ATools 17 3 4 Connecting to a digital audio 7 5 Games 18 amplifier and TV using HDMI 7 7 6 Media 19 3 5 Connecting to an analogue Audio Amplifier 7 TEKCOMM declares that this item complies with the basic requirements and other relevant regulations of directives 2004 108 EC and 73 23 EC RoHS 2002 95 EC Subject to alterations In consequence of continuous research and development technical specifications design and appearance of products may change HDMI the HDMI logo and High Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries Manufactured under license from Dolby Laboratories Dolby and the double D symbol are registered trademarks of Dolby Laboratories All other product names are trademarks or registered trademarks of their respective owners TEKCOMM 2015 All rights reserved TEKCOMM 1 0 INTRODUCTION 1 1 Safety Instructions DO NOT INSTALL YOUR RECEIVER m Ina closed or poorly ventilated cabinet directly on top of or under any other equipment on a surface which might obstruct the ventilation slots DO NOT EX
3. Locks the installation menu You can set Menu Lock to On or Off Parental Rating Choose between Off 4 years and up to 18 years Channels with a parental rating above the chosen age will be protected with a PIN code if available in your local broadcast New Password Enter your new PIN code 4 digits here Confirm Password Re enter your PIN code here to confirm 7 3 6 OSD Setting This menu allows you to change settings for OSD Timeout and OSD Transparency OSD Timeout Sets the duration time of on screen banners and messages remove The range is 1 10 seconds or Always On OSD Transparency To set the OSD transparency from Off 40 with 10 steps Load Default OSD Setting Press OK to clear all OSD settings and reset to default values 7 3 7 Audio Description Setting For the visually impaired a new feature is developed adding a spoken description to the original audio about the video content NOTE This is subject to availability by the broadcaster Switch the service On or Off A transmission with AD will then be signalled the info banner Switch also Use as default to On it will automatically cause the AD audio track to be mixed with the original audio and made audible With AD Volume Offset the level of the added description can be adapted 3 to 3 7 3 8 Auto Standby Auto Standby is a new feature that helps you reducing power consumption When set to 30Min 1 Hour 2 Hours or 3 Hours the receiver will switch to
4. Music 4 Press 4 to open a previously created play list Then you can select the music file that you want to add your play list by pressing 5 a single file will be 19 TEKCOMM added to the play list or 6 all files of this directory folder will be added to the play list 5 Press 5 to add a file to the playlist A favourite icon will be shown next to the file 6 Press 6 to add all files of this directory folder to the play list Press 6 again to delete all files from the play list 7 Press 7 to open the Edit menu This menu allows access to the following functions by entering the number rename 4 copy 5 delete 6 create folder 7 2 Press 2 to open the sort window You can sort by Name Time Size and Favourite INFO Press the INFO button to set repeat mode The option is Repeat Folder Random Folder Repeat One EXIT One step back or leave the folder and quit the function Image 4 Press 4 to open a previously created play list Then you can select the image file that you want to add your play list by pressing 5 a single file will be added to the play list or 6 all files of this directory folder will be added to the play list 5 Press 5 to add a file to the play list A favourite icon will be shown next to the file 6 Press 6 to add all files of this directory folder to the play list Press 6 again to delete all files from the play list 7 Press 7 to open the Edit menu This menu allows access of the fo
5. automatically Select Normal Hard of Hearing or Off Availability of DVB HoH subtitles depends on the broadcast If subtitles not supported they can be activated via Teletext if available 7 3 2 TV System Use this menu to match your receiver to your TV set The following settings are available Video Resolution Use this option to select the video resolution of your TV screen The options are By Source automatic detection of video resolution offered to the receiver By Native TV automatic detection of maximal resolution of TV screen and manual selections 480i 576i up to 1080p Use a setting that matches the specifications of your TV After a selection is made you will be asked to confirm Selection above 576i is only applicable on HDMI output 14 TEKCOMM Aspect Mode Connection Digital Audio Output NOTE Use this option to select the aspect ratio of your TV and the preferred conversion method The options are Auto automatic detection of aspect ratio 4 3 Panscan Displays 16 9 widescreen broadcasts full screen on your 4 3 TV 4 3 letterbox black bars on top and under the picture on a 4 3 TV and 16 9 use this setting for 16 9 TV sets Use this option to select the connection to your TV set Select HDMI or TV SCART RGB If connection type HDMI is selected then only the CVBS signal is available on the TV SCART Toggles between PCM and Bitstream output When PCM is selected all digital au
6. be overwritten After completion the unit will reboot and come back with the first channel in the new channel list 7 4 6 Auto update OTA If set to On the unit will check automatically at the moment of going to stand by for an Over The Air software upgrade An Over The Air update might not be available in your region Please visit our website www tekcomm tv or contact your local service hotline for more information about this option 7 5 Games Your receiver is equipped with two games which can be played on your TV screen using the receiver remote control 18 TEKCOMM Use Y to select Games from the Main menu and press OK or P to proceed Select one of the available games Othello or Sudoku using Y and press OK to start the game Follow the directions on screen Press EXIT to quit a game 7 6 Media The Media menu consists of the following submenus Media Player HDD Information DVR Setting and Remove USB device safely Use Y to highlight the menu of choice and press OK to enter Press EXIT to quit 7 6 1 Media Player This function allows playback of different kind offiles from the connected USB storage device In the Media menu select Media Player and press OK to enter this menu When entering the media player the highlight is on the USB storage device Press W and OK to open the directory respectively its folders subfolders First select which files you like to play back Press 1 to switch between Video Record M
7. standby if it doesn t receive any commands during this time Set Auto Standby to Off to deactivate the automatic standby function 16 TEKCOMM 7 4 Tools Press MENU in viewing mode to enter the Main Menu Select the Tools submenu with A Y and press OK or P to enter Use Y to highlight the submenu of choice and press OK proceed Press EXIT to leave 7 4 1 Information This submenu shows receiver specific information such as hardware version and software version It also displays our web address www tekcomm tv Please have the Information screen on hand when you call our hotline The person who answers your call might ask for the information given in this screen 7 4 2 Load Factory Settings This option allows you to reset the receiver to factory settings which clear all stored channels WARNING By resetting your receiver to factory default all your settings and stored channels will be permanently deleted Please use this option with care Use Y to select Load Factory Settings in the Tools menu and press OK You are asked to input your PIN code Input the correct PIN code using the 0 9 DEFAULT PIN 1234 A confirmation window is displayed Select Yes to return to factory settings Select No to cancel Press EXIT to leave 7 4 3 S W Upgrade by OTA This receiver is equipped with an Over The Air software upgrade function An Over The Air update might not be available in your region Please visit our website www tekc
8. to enter The receiver will display a list with8 timers followed by their respective status Select the timer you wish to set or change with A Y and press OK to proceed The timer setup menu will now be displayed The following settings are available Timer Mode Choose between Off the timer is inactive Once Daily the timer will be executed every day same time or Weekly the timer will be executed every week same day same time and Monthly the timer will be executed every month same day same time 15 TEKCOMM Timer Service Choose between Channel the timer will wake up the receiver or Record Timer will start recording the scheduled event Wakeup Channel Use P to select the channel the timer will wake up with Wakeup Date Use the 0 9 buttons to enter the date for the timed event Wakeup Time Use the 0 9 buttons to enter the starting time Duration Use the 0 9 buttons to enter the duration of the timer When all settings have been made use Y to move the highlight to Save and press OK to confirm To quit the timer without saving your settings move the highlight to Cancel 7 3 5 Parental Lock This menu allows you to protect the installation menu and or channels with a PIN code You can also enter a new PIN code in the Parental Lock menu Use Y to select Parental Lock from the System Setup menu and press OK to proceed You will be asked to enter your PIN code DEFAULT PIN 1234 Menu Lock
9. After performing this function the USB device is no longer accessible from your receiver To gain access to your storage device again re insert it or switch the receiver to standby and on again A 1 Troubleshooting There may be various reasons for abnormal operation of the receiver Check the receiver according to the procedures shown below If the receiver does not work properly after checking it please contact your dealer or the local Service Hotline Do NOT try to open or disassemble the receiver It may cause a dangerous situation and warranty will be void 21 TEKCOMM Problem Possible cause What to do The LED indicator does not lit Mains lead is unplugged Check the mains plug No signal found The antenna is disconnected The antenna is damaged misaligned Out of digital signal area The active antenna requires the antenna power external power to be switched ON Check the antenna lead Check the antenna Check with your dealer Switch the antenna power of the receiver ON connect external power No picture or sound on HDMI or SCART are not selected Switch to the correct TV amplifier remote control The remote control is not aimed correctly The front panel is obstructed The batteries of the remote control are exhausted TV or amplifier on your TV or the amplifier or input unit are set to a higher resolution Select lower resolution on the than the TV supports receive
10. No to discard Delete Press BLUE in Edit Channel to enable the Delete function The Delete sign will move up to indicate that Delete is selected Use Y to highlight a channel and press OK to mark it for deletion When 12 TEKCOMM you have marked all channels you wish to delete press EXIT twice A confirmation banner will be displayed Select Yes to delete the marked channels or No to cancel 7 1 2 Radio Channel List Basically the operation of the Radio Channel List is the same as in the TV Channel List The only difference is that in Radio Channel List there is no video information so it will always display the radio background on the preview screen 7 1 3 Delete all Use this menu to delete all stored channels Select Delete All with Y and press OK The receiver asks you to enter the pin code DEFAULT PIN 1234 Inside the confirmation window select Yes with 4 gt and press OK to delete or select No to cancel WARNING The Delete all function will permanently delete all current channels and all favourite lists from your receiver and you are not able to leave the menu until you search for channels again 7 1 4 Rename Favourite list This menu allows you to personalize the names of the8 available favourite lists Use Y to select Rename Favourite List from the Edit Channel Menu and press OK to proceed The names of all groups are now displayed Select a favourite group with A Y and press OK to edit its name A tex
11. POSE THE RECEIVER OR ITS ACCESSORIES m direct sunlight or any other equipment that generates heat to rain or intense moisture to intense vibration and to any shock which may cause permanent damage to your receiver or to any magnetic objects such as loudspeakers transformers etc m Do not use a damaged power cord It may cause a fire or an electric shock Do not touch a power cord with wet hands It may cause an electric shock m When the receiver is not used for a long period of time you should unplug the power cord rom the wall socket m Donot use alcohol or ammonia based liquids to clean the receiver If you wish you may clean your receiver with a soft lint free cloth slightly made damp with a mild soap solution and only after disconnecting from the mains voltage supply Make sure no foreign objects fall through the ventilation slots because this could cause fire or an electric shock Donot place any objects on top of the receiver because this might prevent proper cooling of the components inside Safety Precautions m Never try to open the receiver It is dangerous to touch the inside of the receiver due to high voltages and possible electrical hazards Opening the receiver will void the warranty of the product Refer all maintenance or servicing to suitably qualified personnel m When you are connecting cables be sure that the receiver is disconnected from the mains supply voltage Wait a few seconds after switching off
12. TEKCONMM Bulan Terminal Num rique Terrestre um Haute D finition TCT2100 z 0 rpoLDyY TEKCOMM Manuel d utilisation User Manual Fig 1 Fig 2 Fig 3 Fig 6 Antenna ital Terrestrial High Definition Receiver jodel TCT2100 ANTIN man A Fig 7 gt Amplificateur Audio Amplificateur audio analogique Digital Terrestrial High Definition Recover Model TCT2100 tA Fig 8 lt TIpotsy TEKCOMM P riph rique de stockage USB HOTLINE 0826 029 928 support_fr strong tv 0 15 par mn poste fixe en France Supplied by STRONG amp Co Japan Represented by STRONG Ges m b H Franz Josefs Kai 1 1010 Vienna Austria Email support_at strong tv TEKCOMM 17 Jun 2015 12 34 TEKCOMM Licenses ANY USE OF THIS PRODUCT IN ANY MANNER OTHER THAN PERSONAL USE THAT COMPLIES fe WITH THE MPEG 2 STANDARD FOR ENCODING VIDEO INFORMATION FOR PACKAGED MEDIA mas 15 EXPRESSLY PROHIBITED WITHOUT A LICENSE UNDER APPLICABLE PATENTS IN THE MPEG 2 PATENT PORTFOLIO WHICH LICENSE IS AVAILABLE FROM MPEG LA LLC 6312 S Fiddlers Green Circle Suite 400E Greenwood Village Colorado 80111 U S A THIS PRODUCT IS LICENSED UNDER
13. THE AVC PATENT PORTFOLIO LICENSE FOR THE PERSONAL AND NONCOMMERCIAL USE OF A CONSUMER TO i ENCODE VIDEO IN COMPLIANCE WITH THE AVC STANDARD AVC VIDEO AND OR ii DECODE AVC VIDEO THAT WAS ENCODED BY A CONSUMER ENGAGED IN A PERSONAL AND NON COMMERCIAL ACTIVITY AND OR WAS OBTAINED FROM A VIDEO PROVIDER LICENSED TO PROVIDE AVC VIDEO NO LICENSE IS GRANTED OR SHALL BE IMPLIED FOR ANY OTHER USE ADDITIONAL INFORMATION MAY BE OBTAINED FROM MPEG LA L L C SEE HTTP WWW MPEGLA COM This product contains one or more programs protected under international and U S copyright laws as unpublished works They are confidential and proprietary to Dolby Laboratories Their reproduction or disclosure in whole or in part or the production of derivative works therefrom without the express permission of Dolby Laboratories is prohibited Copyright 2003 2009 by Dolby Laboratories All rights reserved 25 Sep 2015 16 47 TEKCOMM TABLE OF CONTENT 1 0 INTRODUCTION 3 3 6 Connecting a USB storage 1 1 Safety Instructions 3 device 7 1 2 Storage 3 4 0 STARTING UP FOR THE FIRST TIME 8 1 3 Equipment Set up 4 5 0 QUICK GUIDE TO USING 1 4 Accessories 4 YOUR RECEIVER 9 1 5 Usage of external USB devices 4 6 0 OPERATION 9 2 0 YOUR RECEIVER 5 6 1 Changing channels 9 2 1 DEFAULT PIN 1234 5 6 2 Info Banner 9 2 2 Front Panel 5 6 3 Selection of audio language 10 2 3 Rear Panel 5 6 4 Teletext 10 24 Remote control 5 6 5 Subtitles 10 2 5 Installing the batteries
14. TV set Select HDMI or TV SCART Availability of DVB HoH subtitles depends on the broadcast If subtitles are not supported they can be activated via Teletext if available When all settings have been made move the highlight to OK and press OK to continue NOTE Wrong region selection can lead to missing channels or channels being stored at wrong positions in the channel list The receiver will now advance to the Aerial Adjustment screen This part of the wizard is of great help when setting up your antenna system Use Y to move the highlight to the setting you wish to alter and use lt gt to change values The following settings are available Antenna Power Set to On if you use an active antenna When set to On 5 V will be present at the ANT IN connector of the receiver Select Off for passive antennas Beeper Select On for an audible indication of signal reception Off turns the beeper off Channel No Select a channel that is known to carry a broadcast in your region The Signal Strength and Signal Quality bars give a visual indication of the reception Adjust your antenna to obtain maximum signal strength and quality When all settings have been made press OK to start scanning The receiver will search for all available channels now Once scanning is finished the receiver switches to viewing mode TIP If the Welcome menu does not appear after switching on the receiver the first time reset the receiver to factory
15. The coloured buttons of the remote control allow you to jump to selected pages directly as indicated on the bottom of the Teletext screen Use the Y buttons to select one page up or down use the gt buttons to select subpages Press EXIT or TTX to get back to viewing mode 6 5 Subtitles Some channels support a choice of subtitle languages Press SUBTITLE in viewing mode to display a list of available subtitle languages Select your subtitle of choice with Y and press OK to confirm Press EXIT to leave without making changes Availability of DVB HoH subtitles depends on the broadcast If subtitles are not supported they can be activated via Teletext if available 6 6 Timeshift Timeshift allows you to pause live broadcasts and resume playback later To activate this function set the Timeshift mode in the DVR Setting menu to on by selecting Pause For details see 7 6 3 Press H in viewing mode to activate Timeshift The progress information banner appears on screen Live TV keeps playing for moment and will then pause Press to resume Timeshifted playback Press STOP to return to live TV NOTE Timeshift and its playback only work properly when a fast USB storage device such as a USB2 0 HDD is connected to the receiver Timeshift and playback of HD content requires sufficient read write speed of the used USB storage device 6 7 EPG Electronic Programme Guide The Electronic Programme Guide is a very useful function that allo
16. a fast USB storage device such as a USB2 0 HDD is connected to the receiver Timeshift recording and playback of HD content require a sufficient read write speed of the used USB storage device TEKCOMM 4 0 STARTING UP FORTHE FIRSTTIME When you use your receiver for the first time the Welcome Easy install menu appears Use Y to move the highlight to the setting you wish to alter and use lt gt to change values Start by selecting your language using lt P gt Once you have selected your language press Y to move the highlight to the next item and use 4 P to change Language Here you can choose your language Region Select your region where this receiver is used Subtitle Select Normal to display subtitles per default Select Hard ofHearing to show HoH subtitles per default Select Off to hide subtitles per default Aspect Mode Use this option to select the aspect ratio of your TV and the preferred conversion method The options are Auto automatic detection of aspect ratio 4 3 Panscan Displays 16 9 widescreen broadcasts full screen on your 4 3 TV 4 3 letterbox black bars on top and under the picture on a 4 3 TV and 16 9 use this setting for 16 9 TV sets Scan mode Select All to store scrambled and free to air channels or select Free to store only free to air channels Note Scrambled channels cannot be viewed with this receiver Connection Use this option to adjust the established connection to your
17. ations Demodulator Demodulator Transmission mode Video Decoder Profile level Video resolutions Decoding amp Video out Aspect ratio Audio Decoder Audio support Sampling rate Audio mode COFDM 16 QAM 64 QAM QPSK 2K 8K MPEG 2 MP ML AVC H264HP L4 1 MPEG4 ASP supported 480i 480p 576i 576p 720p 1080i 1080p By Native TV By source PAL 4 3 Letterbox 4 3 Pan amp Scan 16 9 Auto AAC Dolby Digital Plus AC3 PCWAC3 MPEG MusiCam Layer II 32 44 1 48 KHz Stereo Mono Dolby and the double D symbol are registered trademarks of Dolby Laboratories Tuner Front End Input frequency range Input signal level Memory and System Flash memory SDRAM Multimedia Video playback Audio playback Picture view DVB T UHF amp VHF Tuner 174 230 MHz VHF and 470 862 MHz 20 84 dBm 4MB 64 MB MPEG 1 and MPEG 2 encoded mpg VOB AVI MKV TS M2T M2TS MPEG 4 and MOV MP3 OGG BMP JPEG TEKCOMM cannot guarantee the playback of all files although extensions are listed as it depends on codec used data bit rate and resolution all MPEG codec formats are supported Connectors ANT IN IEC Female HDMI TV SCART RGB CVBS Audio L amp R USB 2 0 port 5 V 800 mA max supported General Data Supply voltage 220 240 V AC SMPS 50 60 Hz TEKCOMM TEKCOMM Power consumption Power consumption in standby Operating temperature Stora
18. cable This connection gives the highest possible quality 3 3 Connecting to TV with SCART cable Fig 6 Your receiver is also equipped with a SCART connector alternatively the TV set can be connected to the receiver using a good quality SCART cable 3 4 Connecting to a digital audio amplifier and TV using HDMI Fig 6 By connecting your receiver to the latest digital amplifiers or Home Cinema systems you will enjoy the best possible sound quality and multi channel audio depending on the broadcast Connect the HDMI output of the receiver to an input of your amplifier and then connect the HDMI output of the amplifier to your TV set Select the correct input on your amplifier to watch and listen to programmes 3 5 Connecting to an analogue Audio Amplifier Fig 7 Use an optional SCART to Cinch cable to connect your receiver to the analogue input of your Hi Fi or audio amplifier to achieve best possible analogue audio quality if SCART is not in use for Video 3 6 Connecting a USB storage device Fig 8 Connecting a USB device to the unit allows you to playback movies music and picture files which are stored on it See chapter 7 5 1 Mediaplayer Additionally TV programmes can be recorded put on hold Timeshift and played See chapter 6 Operation NOTE It is recommended to use USB 2 0 storage devices or higher for recording and playback of TV programmes or HD movies NOTE Timeshift recording and playback only work properly when
19. cording 7 0 MAIN MENU The main menu gives you access to settings multimedia functions and games To access the main menu press MENU in viewing mode The main menu consists of the following sub menus Edit Channel Installation System Setup Tools Games and Media Throughout the main menu MENU or EXIT can be used to get back to the previous screen 7 1 Edit Channel Use Y to select Edit Channel and press or P to enter Use Y to highlight the submenu of choice and press OK to select Press EXIT lt to get back to the main menu 7 1 1 TV Channel List n the Edit Channel menu select TV Channel List with Y and press OK to enter Use lt P to change the channel group if you have already set up favourite groups Select the channel of choice with Y Press OK to view the selected channel in the preview box 7 1 1 1 Adding channels to favourite lists Channels from the TV Channel List can be added to up to8 different favourite groups Press FAV in TV Channel List to access this function The FAV sign on the top of the screen will move up to indicate that the favourite function is selected Use A Y to select a channel you wish to add to a favourite group When the highlight is on the channel of your choice press OK A list with all available favourite lists will now pop up Use A Y to select the favourite list you wish to add the channel to and press OK press EXIT to finalize the process Favourite channels will b
20. der that power specifications may exceed the supported output of your receiver max 5 V 800 mA If so please connect your USB HDD to an according external power adapter m Itis advised not to store important information on USB storage devices used with the receiver Always make backups of data on your USB storage device before using it with this receiver TEKCOMM will not take responsibility for any loss of information or circumstances caused by loss of information TEKCOMM 2 0 YOUR RECEIVER 2 1 DEFAULT PIN 1234 2 2 Front Panel 1 USB 2 IRsensor 3 Mode indicator 4 Standby On button 2 3 Rear Panel ANTIN HDMI TV SCART Power cord 2 4 Remote control 1 O 2 3 PG PG 4 DTV VCR 5 INFO 6 VOL VOL 7 MENU 8 EXIT 9 AY 10 4 gt 11 12 RECORD 13 TIMESHIFT 14 0 9 15 EPG Fig 1 Connector for USB storage devices Point your remote control towards this sensor RED indicates that the receiver is STANDBY mode GREEN indicates that the receiver is in OPERATING mode Switch receiver ON to running mode or STANDBY mode Fig 2 To connect to your antenna for reception of broadcasted signals To connect your receiver with your TV set using an HDMI cable To connect your receiver with your TV set using a SCART cable Your receiver requires a supply voltage of 220 240 V AC Auto selectable 50 60Hz 5 Please ensure the local power specification meets these requi
21. dio will be converted to stereo audio Bitstream enables you to listen or transfer Dolby Digital Dolby Digital Plus audio to the TV via HDMI or toa Home entertainment system Dolby Digital Plus is only available on the HDMI output Dolby and the double D symbol are registered trademarks of Dolby Laboratories 7 3 3 Local Time Setting Here you can set up your region and time zone Region Use P to select the region you live in GMT Usage Set to By Region for broadcaster defined time User Define to select manual a GMT zone or to Off to input time and date manually GMT Offset Allows you to adjust your time zone This option is only available when GMT Usage is set to User Define The GMT Offset range is 11 30 12 00 increasing by half hours progressively The cities matching the set GMT Offset are displayed at the bottom of the screen Daylight Saving Select On to add one hour for summer time Date Date and Time settings are available only when GMT Usage is set to Off Use the 0 9 buttons to enter the date Press EXIT to proceed Time Date and Time settings are available only when GMT Usage is set to Off Use the 0 9 buttons to enter the time Press EXIT to proceed Time Display Select On to display time on screen Off to remove 7 3 4 Timer Setting This menu allows you to set up to8 timed events for recording or waking up the receiver Use Y to select Timer Setting from the System Setup menu and press OK
22. e marked with When all changes have been made press EXIT twice A confirmation banner will pop up Select Yes to save the changes or No to discard 7 1 1 2 Locking channels Locked channels can only be watched after entering the PIN code DEFAULT PIN 1234 To lock or unlock a channel press RED while in TV Channel List Press Y to select a channel and press OK to lock or unlock it You are asked to input the PIN code DEFAULT PIN 1234 gt Locked channels will be marked with the LOCK symbol Locking unlocking multiple channels in one session 11 TEKCOMM is possible When all changes have been made press EXIT twice A confirmation banner will pop up Select Yes to save the changes or No to discard 7 1 1 3 Skipping channels Channels marked with Skip will be skipped when zapping channels with the Y buttons The channels will still be available from the channel list mark channels for skipping press GREEN while in TV Channel List Use Y to select a channel and press OK to mark or unmark it for skipping Channels set for skipping will be marked with the symbol When all changes have been made press EXIT twice A confirmation banner will pop up Select Yes to save the changes or No to discard 7 1 1 4 Moving channels To enable the Move function press YELLOW while in TV Channel List Use Y to select a channel and press OK to select it Now you can move the selected channel up or down inside the channel lis
23. ge temperature Operating humidity range Size WxDxH in mm Net weight 3 65 W typ 12 00 W max max 0 4 W 0 C 40 C 10 C 50 C 10 85 RH Non condensing 141x113x40 0 31 kg 24
24. llowing functions rename 4 copy 5 delete 6 create folder 7 2 Press button 2 to open the sort window You can sort by Name Time Size and Favourite INFO Press INFO to access slideshow settings You can change the slide time and slideshow repetition 3 Press 3 to show the files in a preview of 3x3 pictures EXIT One step back orleave the folder and quit the function 7 6 2 HDD Information This option shows relevant information about the connected USB device In this menu you can also format your USB storage device and setup the recording type Select HDD Information in the Media menu and press OK to enter Now you will see all details as Free and the used Recording Sizes and the used file system Press the YELLOW button Format to format the connected USB device Please enter your PIN code to access this menu and press OK to start formatting WARNING Formatting will permanently delete ALL data stored on the connected device Please make a backup copy ofall data you wish to keep before entering the HDD Format menu TEKCOMM cannot be held responsible for loss of data from USB devices used with this receiver 20 TEKCOMM Press OK to proceed select FAT or Cancel or press EXIT to leave without formatting Press BLUE DVR Set to select recording type Select REC amp TMS to store recordings and Timeshift copies to your HDD Select Record to store only recordings to your HDD Select Timeshift to switch recordings OFF Onl
25. o the compartment Correct position ofthe polar diagram shows the batteries inside the compartment 1 Open the cover 2 Insert the batteries 3 Close the lid WARNING The batteries should not be recharged disassembled electrically short circuited be mixed or used with other types of batteries 2 6 Using the remote control Fig 5 To use the remote control point it towards the front of your receiver The remote control supports a range of up to5 meters distance to the receiver at an angle of up to approx 30 degrees NOTE Managing the receiver will be limited or not possible if there are obstacles between the remote control sensor at the front panel of the receiver and the remote control Direct sunlight or very bright light can reduce or disturb the reception of the remote control signals 3 0 CONNECTIONS 3 1 Connecting to a terrestrial antenna Fig 6 To receive broadcasted signals your terrestrial indoor or outdoor antenna must be connected to the ANT IN connector on the back of the receiver Use a properly shielded antenna cable and suitable connectors TEKCOMM NOTE If the signals at your location are too weak to receive proper signals with an indoor antenna we recommend using an outdoor antenna which can be pointed towards the transmission tower Ask your local dealer for more information 3 2 Connecting to TV with HDMI cable Fig 6 The TV set shall be connected with the receiver using a good quality HDMI
26. omm tv or contact your local service hotline for more information about this option 7 4 4 Upgrade by USB This feature allows you to upgrade receiver software via the USB port When new software is available or your receiver it can be downloaded from our website www tekcomm tv Place the software file unzipped in the root directory of your USB storage device HDD memory stick etc and connect the device to the USB port of the receiver Select Upgrade by USB from the Tools menu and press OK to proceed The upgrade menu will now be displayed Use Y to select Update Mode and choose option Allcode Use Y to select Upgrade File and choose the file containing the latest and correct software When all settings have been made move the highlight to Start and press OK to start the upgrade process After a few seconds the receiver asks Are you sure to burn flash Select Yes to finalize the upgrade or No to quit without upgrading 17 TEKCOMM NOTE If after a software upgrade the receiver should behave in an unexpected way please perform a factory reset as well See chapter 7 4 2 WARNING After an update the receiver restarts automatically During the upgrade process NEVER disconnect the receiver from the mains or switch off the power Doing so might damage your receiver and will void warranty 7 4 5 Channel Dump and Load function This feature allows you to load a channels list quickly and use a channel list tha
27. r TV amplifier are not switched on Switch the TV amplifier on Scrambled channel The channel is scrambled Select an alternative channel message No response to the The receiver is off Plug in and turn on the plug Aim the remote control at the ront panel Check for obstructions Replace the batteries of the remote control Forgotten PIN code Forgotten channel lock code Default PIN is 1234 Contact the local Service Hotline or send an email to our Support via www tekcomm tv After moving the receiver to another room area you are no longer able to receive digital reception The antenna signals are too weak The signal strength quality might be less than before if using an indoor antenna Press INFO on the remote control 3x to call up the signal bars and adjust the antenna for maximum reception or rescan channels When using an active antenna check antenna power Try to use an outdoor antenna The receiver switches off automatically The Auto Standby function is enabled Disable the auto standby See section 7 3 7 for details Playback of video or Timeshift is causing picture freeze macro blocks or similar distortion especially on HD content The reading writing speed of your USB device may be too low Make sure to use a USB storage device with sufficient speed and space Pen drives USB sticks may not support sufficient speed 22 A 2 Technical Specific
28. rements before connecting your receiver to the wall outlet Fig 3 Switches the receiver On Standby Mutes all audio outputs of the receiver Page up down in all list modes No function Opens the current channel information 2x opens the current event information and 3x the signal information Increases decreases the volume level Opens the main menu in a menu you will get one step back Exits from the menu or sub menu Menu Off Change channel to next previous Menu On Moves the cursor up down Menu Off Decreases increases the volume level Menu On Change settings for specific menus Menu Off Displays the current channel list Menu On Activates the highlighted menu item Records the TV programme to the connected USB storage device Activates the Timeshift function Off On Enters a channel number in viewing mode or a value inside the respective menu Opens the EPG Electronic Programme Guide in TV mode TEKCOMM 16 RECALL Back to previously watched channel 17 AUDIO Opens the audio language selection 18 TV RADIO Toggles between TV or RADIO mode 19 FAV Opens the favourite group selection 20 FILE Opens the Media Player list 21 TTX Displays Teletext on the OSD On Screen Display 22 SUBTITLE Shows a list of subtitle languages 23 Fast rewind fast forward 24 Coloured buttons For Multimedia and Teletext functions 2 5 Installing the batteries Fig 4 Open the cover on the remote control and insert 2x AAA batteries int
29. settings by pressing the MENU button and selecting Load Factory Setting in the submenu Tools DEFAULT PIN 1234 TEKCOMM 5 0 QUICK GUIDE TO USING YOUR RECEIVER We at TEKCOMM understand that you can t wait to enjoy your new digital terrestrial HD receiver The following quick guide will make you familiar with the basic operation of this device We do however advice you to read the full manual to get the best performance from your receiver To turn your receiver ON or to Standby use the button on the remote control Choose a channel with A Y Alternatively you can digit the channel number with the 0 9 buttons on the remote control or press OK in viewing mode to display the channel list The volume can be adjusted with lt gt 6 0 OPERATION 6 1 Changing channels Following ways are possible for changing channels with your new receiver m Via direct access using the 0 9 buttons m Via the channel list using OK and the PG PG buttons m Via the Y buttons 6 1 1 Direct access via 0 9 buttons o gain direct access to a certain channel simply input its number with the 0 9 buttons on the remote control Channel numbers can be up to four digits long Entering a number with less than our digits is possible Just wait a few seconds and your receiver will switch to the selected channel or press OK immediately after selecting the channel number 6 1 2 Channel list Press OK in viewing mode to display the Channel List Use A Y in
30. t by using Y When the channel is on the position of your choice press OK again The channel is now ixed on its new position When all changes have been made press EXIT twice A confirmation banner will pop up Select Yes to save the changes or No to discard 7 1 1 5 Editing channels The Edit function allows you to Sort Rename or Delete channels To enter the Edit menu press BLUE while in TV Channel List The Edit Channel menu will appear f you made changes in the previous menu but haven t saved them yet you will be asked to do so now Sort Press RED to enter the Sort menu Use Y to select sorting method and press OK to confirm Possible methods are Name A Z Sorting in alphabetical order from A to Z Name Z A Sorting in alphabetical order from Z to A Free Scramble First in the list will be Free To Air channels Lock All unlocked channels will placed first in the list Default Sorting by searched Order from lowest to highest frequency or by LCN numbering Rename Press GREEN in Edit Channel to enable the Rename function The Rename sign will move up to indicate that Rename is selected Use Y to highlight a channel and press OK to select it A text field will now pop up at the right of the screen Use gt Y to select characters and enter them with OK When you have finished editing press BLUE to enter the changes When all changes have been made press EXIT twice Select Yes to save the changes or
31. t field will now up at the right of the screen Use A Y to select characters and enter them with OK When you have finished editing press BLUE to save the changes When all changes have been made press EXIT twice to leave this menu 7 2 Installation 7 2 1 Auto Scan Use Y to select Installation and press OK or gt to advance Select Auto Scan with Y and press OK to enter Use P to toggle between Yes No When FTA Only is set to Yes scrambled channels won t be stored in the channel list Use Y to highlight Search Now press OK to start the auto scan The receiver will store all found channels in the channel list 7 2 2 Channel Scan Use Y to select Installation press OK or P gt to advance Use Y to select Channel Scan and press OK to enter Use gt to toggle between the available scan modes By Channel and By Frequency If By Channel is selected use the cursor buttons to select Scan Band and Channel No If By Frequency is selected use the cursor buttons to select Frequency and Bandwidth Highlight Search and press OK to start scanning Newly found channels will be added to the channel list 13 TEKCOMM 7 2 3 Antenna Power Use Y to select Installation press OK or P gt to advance Use Y to select Antenna Power and press OK to enter Set to On if you use an active antenna Select Offfor passive antennas When set to On 5 V will be present on the ANT IN connector of the recei
32. t previously was created on this backup or another receiver from the same model via the USB port This is useful when more receivers have to be installed in the same region thus omitting a full scan and optional sorting of channels It is also useful as a backup for your own unit Channel Dump function backup to USB Have a storage device connected to the USB port of the receiver Select Upgrade by USB from the Tools menu and press OK to proceed The upgrade menu will now be displayed Use Y to select Update Mode and choose the option Dump channel list Use Y to select Upgrade File A DataBase file name containing date and time will be presented format DBYYYYMMDDHHMM DateBaseYearMonthDateHourMinute udf Use Y to select Start and press OK to proceed The channel list and favourites will be saved Update Channel list function read from USB Have the storage device connected to the USB port of the receiver containing a previously made channel list on this unit or another ofthe same model Select Upgrade by USB from the Tools menu and press OK to proceed The upgrade menu will now be displayed Use Y to select Update Mode and choose the option Update Channel list Use Y to select Upgrade File Select the correct database file name format DBYYYYMMDDHHMM DateBaseYearMonthDateHourMinute udf Use Y to select Start and press OK to proceed Confirm the upgrade with OK to proceed Warning Old channel list and favourites will
33. the channel list to highlight your channel of choice and press OK once to select the highlighted channel Press OK again to leave the channel list mode Inside the channel list it is possible to use the PG PG buttons as well in order to scroll page wise through the list TIP Use lt gt to toggle between the All Channel list and favourite list s or press FAV in viewing mode or a list of the available favourite lists 6 1 3 Using the av buttons A switches to the next channel Y switches to the previous channel 6 2 Info Banner While watching TV you can press the INFO button at any time to access current information about the channel and event Press INFO twice for extended EPG details about the current channel Press INFO three times for technical details about the current channel Event information is displayed when available Availability depends on the broadcast TEKCOMM 6 3 Selection of audio language Some channels support a choice of audio formats and or languages To select another audio stream press AUDIO in viewing mode A list with available audio streams will now be displayed Use Y to select a stream and confirm with OK The audio channel as stereo mono left and right can be selected with the lt gt buttons 6 4 Teletext Your receiver includes a fully featured Teletext To access Teletext press the TTX button in viewing mode and use the 0 9 buttons to input the number of the page you wish to see
34. the receiver before you move the receiver or disconnect any equipment m Itis a necessity that you only use an approved extension and compatible wiring that is suitable for the electrical power consumption of the installed equipment Please ensure that the electrical power supply corresponds with the voltage on the electrical identification plate at the back of the receiver If the receiver does not operate normally even after strictly following the instructions in this user manual it is recommended to consult your dealer 1 2 Storage Your receiver and its accessories are stored and delivered in a packaging designed to protect against electric shocks and moisture When unpacking it make sure that all the parts are included and keep the packaging away from children When transporting the receiver from one place to another or if you are returning it under warranty conditions make sure to repack the receiver in its original packaging with its accessories Failing to comply with such packaging procedures could damage the product and void your warranty TEKCOMM 1 3 Equipment Set up We recommend you consult a professional installer to set up your equipment Otherwise please follow the instructions below m Refer to the user manual of your TV if applicable your antenna m Make sure that the HDMI cable and if applicable outdoor components are in a good condition m Ifyou use TV SCART connection use then well shielded SCART cable
35. usic or Image Press Y to select a file or folder and then press OK to open the folder subfolder if applicable or start playback of the file Press the EXIT button to exit Use the buttons like described below in order to choose functions during the different playback modes like described in the help banner below Video INFO Press the INFO button to set repeat mode The options are repeat folder folder icon repeat once 1 or no repetition no icon shown 1 During the playback of a movie with external subtitles press 1 to enter the subtitle menu In this menu you can select size and colours of your preference 2 Press 2 to open the Sort menu You can sort by Name Time or Size 7 Press 7 to open the Edit menu This menu allows accessing the following functions by entering the number rename 4 copy 5 delete 6 create folder 7 EXIT One step back or leave the folder and quit the function Record 2 Press 2 to enter a new name for the selected recording 3 Highlight the recording that you want to lock After pressing 3 you will be asked to input your PIN code DEFAULT PIN 1234 After entering your PIN code the recording is locked If you want to unlock the recording again press 3 again 4 Press 4 to mark the recording you want to delete By selecting the same recording and pressing 4 again you can remove the delete marker again Press EXIT to delete EXIT One step back or leave the folder and quit the function
36. ver Press EXIT to leave the Antenna Power menu 7 2 4 LCN Logical Channel Numbering If LCN Logical Channel Numbering is activated and an LCN signal is provided by the operator channels will be stored in the operator defined order Set LCN to On to activate the operator defined channel numbering or Off to store channels in the found order This function only applies when a new channel search is performed 7 3 System Setup This menu allows you to manage the system settings of your receiver It consists of the following sub menus Language TV System Local Time Setting Timer Setting Parental Lock OSD Setting and Auto Standby Press Y to highlight the menu of choice and press OK advance to the next screen Use Y to move the highlight to the setting of choice Values can be changed with lt P Press EXIT to leave 7 3 1 Language This menu allows you to set up your language preferences Language Use P to select the language for the On Screen Display First Audio Use 4 P to select Audio language Second Audio Use lt P to select a language that will be played when the language selected at First Audio isn t available Subtitle Language Use lt P to select the preferred subtitle language 2nd Subtitle Language Use gt to select the preferred 2nd subtitle language Teletext Use lt P to select the preferred Teletext language when available Subtitle Use lt P to select the preferred subtitle type to be displayed
37. ws you to view event schedules and programme information and to mark events movies for recording To access the EPG press the EPG button in viewing mode Use A Y to select a channel and 4 select an event Press OK to display detailed information of the selected event Use EXIT to quit the detailed information screen Press RED to access further step functions Use lt P to select a step and OK to execute it Press EXIT to quit the step function Press GREEN to set a timer for a selected event Refer to section 7 3 4 for details of the timer function NOTE Availability of EPG data depends on the broadcast 10 TEKCOMM 6 8 Instant Recording Your new receiver allows you to make an instant recording of the programme you are watching Simply press RECORD to start the recording To enter the duration for the recording press RECORD again while the program banner is visible Use the 0 9 buttons to enter the recording time and press OK to confirm At the beginning of the recording a recording sign will be shown for a short while on the upper left corner of your TV screen To stop the recording press STOP Select Yes and press OK again to stop the recording It is possible to make2 recordings at the same time if they are broadcasted on the same frequency You can access the Record Manager via the FILE button and select Record by pressing the button 1 Please connect a USB storage device with sufficient free space before you start a re
38. y the Timeshift function is active NOTE It is possible to use USB storage devices already formatted in NTFS Press EXIT to leave this menu 7 6 3 DVR Setting This menu allows you to configure settings for Timeshift recording and playback Select DVR Setting in the Media menu and press OK to enter Use Y to move the highlight and gt to change settings Timeshift Select between Auto Pause or Off When Timeshift is set to Auto it will automatically start every time after tuning to a channel When Timeshift is set to Pause it will start only after pressing the YELLOW II button Select Off to deactivate Timeshift Step to 30 sec to 30 min Set the time step you like to jump forward to by pressing 4 during playback of recorded files This only works when the info banner is displayed on screen If it is not press INFO Time Shift to Record If set to On the timeshifted part will be included in your recording when you start to record the current programme PS Record Select between On or Off When Offis selected recordings will also include subtitles and Teletext when available Record to PS mode On allows recordings without these extras and will need less space on your USB device Press EXIT to leave this menu 7 6 4 Remove USB device safely Select Remove USB device safely from the tools menu and press OK The receiver will display a message indicating that you can safely remove your storage device from the receiver NOTE
Download Pdf Manuals
Related Search